Mold Armor FG591 User manual

  • Hello! I am an AI chatbot trained to assist you with the Mold Armor FG591 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FG591 / J9189
EPA Registration No. 4091-23
EPA Establishment No. 55852-IL-001
QUESTIONS? COMMENTS?
CALL 888-326-7743
©2019 WM Barr & Co., Inc.
Distributed by: W.M. Barr & Co., Inc.
6750 Lenox Center Court
Suite 200, Memphis, TN 38115
PRECAUTIONARY STATEMENTS: Hazards to Humans and Domestic Animals
WARNING: Causes moderate eye irritation. Do not get on skin or on clothing. Avoid contact with
eyes. Wear waterproof gloves and appropriate clothing. Wash thoroughly with soap and water
after handling and before eating, drinking, chewing gum, using tobacco or using the toilet. Remove
and wash contaminated clothing before reuse.
FIRST AID:
IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact
lenses, if present, after the first 5 minutes, then continue rinsing eye.
IF ON SKIN OR CLOTHING: Take off contaminated clothing. Rinse skin immediately with plenty of water
for 15-20 minutes.
Call a poison control center or doctor for treatment advice. Have the product container or label with you when
calling a poison control center or doctor, or going for treatment. National Poison Control Center: 1-800-222-1222.
Non-Abrasive Formula · Works Indoors & Outdoors · Contains No Phosphates
Safe for use on: Acrylic, Sealed Fiberglass, Laminate, Steel, Glazed Porcelain,
Glass, Sealed Grout, Stainless Steel, Chrome, Glazed Ceramic, Mirrors, Formica
®
,
Corian
®
, Sealed Granite, Plastic Laminate, Linoleum, Crystal, and Vinyl.
PHYSICAL AND CHEMICAL HAZARDS: This product contains an oxidizing agent. Do not use
or mix with other chemicals such as toilet bowl cleaners, rust removers, or any cleaners
containing acids or ammonia as hazardous gases may be released. Prolonged contact with
metal may cause pitting or discoloration.
ENVIRONMENTAL HAZARDS:This product is toxic to fish and aquatic organisms.
DIRECTIONS FOR USE: It is a violation of Federal Law to use this product in a
manner inconsistent with its labeling.
For surfaces that may contact food, a potable water rinse is required. Do not use on
eating/cooking utensils, glasses/dishes or cookware. Contact with clothing, carpet,
fabric, painted wood surfaces or paper may cause discoloration or damage. Test on
a small inconspicuous area before applying to surface. Safe for use on hard
non-porous surfaces.
USE ONLY IN WELL VENTILATED AREAS. Vapors may irritate. Before use, open windows
and turn on fan. If the vapors bother you, leave the room while the product is working.
TO USE: Pour product into a pump-up sprayer. Do not dilute. Replace trigger or follow
manufacturer’s instructions for use of pump-up sprayer.
TO SANITIZE: For use on hard, non-porous, non-food contact surfaces. Pre-clean heavily
soiled surfaces. Spray surface until thoroughly wet. Let stand 10 seconds. Wipe clean
with a damp cloth. Kills 99.9% of Enterobacter aerogenes and Staphylococcus aureus.
TO DISINFECT bacteria, viruses
, and fungi on hard, non-porous surfaces: Pre-clean
heavily soiled surfaces. Spray surface until thoroughly wet. Let stand 30 seconds. To kill
KEEP OUT OF REACH OF CHILDREN
WARNING
SEE BACK PANEL FOR
ADDITIONAL PRECAUTIONARY STATEMENTS.
KEEP OUT OF REACH OF CHILDREN
WARNING
SEE BACK PANEL FOR
ADDITIONAL PRECAUTIONARY STATEMENTS.
ACTIVE INGREDIENTS:
Sodium hypochlorite......... 4.0%
Sodium carbonate............ 1.0%
OTHER INGREDIENTS: ... 95.0%
TOTAL: ....................... 100.0%
PEEL
HERE
mold and mildew, let stand 60 seconds. Then rinse with water or wipe with a damp
cloth. Kills 99.9% of Pseudomonas aeruginosa, Salmonella enterica, Staphylococcus
aureus, Trichophyton mentagrophytes, Aspergillus niger (60 seconds), Influenza A
H1N1
, Respiratory Syncytial Virus
, Human Coronavirus
.
TO PREVENT MOLD AND MILDEW GROWTH ON HARD SURFACES: To inhibit mold and
mildew growth: Thoroughly wet surface. Allow to air dry. Repeat every 7 days to inhibit mold
and mildew growth. Effective against Aspergillus niger*. Pre-clean heavily soiled surfaces.
TO CLEAN AND REMOVE MOLD AND MILDEW STAINS: Apply to stains. No scrubbing
required. Wait 10 minutes for stains to disappear, then rinse with water or wipe with a
damp sponge. Rinse vinyl or rubber surfaces within 15 minutes as prolonged contact
may cause damage.
TO TREAT WATER DAMAGE CAUSED BY SEWER BACKUP, RIVER FLOODING, LEAKY
PIPES, WINDOWS, ROOFS (NOT FOR USE IN CALIFORNIA):
Extract excess water and
remove gross filth or heavy soil along with non-salvageable materials. Test hidden area for
colorfastness. Saturate affected material with undiluted product using a sprayer with a
coarse spray tip. Allow the materials to remain damp for at least 1 minute prior to extraction.
STORAGE AND DISPOSAL
Store in original container in areas inaccessible to children. Keep securely closed.
Nonrefillable container. Do not reuse or refill this container. Place container in trash
or offer for recycling.
MOLD ARMOR RAPID CLEAN REMEDIATION
Proven one-step disinfectant, cleaner, sanitizer,
fungicide, mildewstat
*
, and virucide
Kills,
Cleans,
& PREVENTS
mold & mildew
Kills Mold.
Visible Results in 1 Minute.
No Scrubbing Required
For Use On Hard Non-porous Surfaces
NET CONTENTS: 1 GALLON
(
3.79 L
)
J9188
TOP PLY
FACER SIDE
PANEL 1
TOP PLY
ADHESIVE SIDE
PANEL 2
BACK OF PANEL 1
BOTTOM PLY
FACER SIDE
PANEL 3
5.7114"
5.7114"
4.4646"
4.4646"
0.1250"
R
0.2500"
5.7114"
4.4646"
5.7114"
4.4646"
/