Danfoss MT50-5VI Installation guide

Brand: Danfoss

Model: MT50-5VI

Type: Installation guide

Instructions

Danfoss reciprocating compressors

MT / MTZ / NTZ / VTZ

8510196P04H - FRCC.PI.049.A4.ML | 1

English / English p. 2

Français / French p. 4

Deutsch / German p. 6

Español / Spanish p. 8

Italiano / Italian p. 10

Português (Brasil) / Brazilian Portuegese p. 12

Polski / Polish p. 14

Dansk / Danish

http://instructions.cc.danfoss.com

Svenska / Swedish

Português / Portuguese

Nederlands / Dutch

Gaeilge / Irish

Suomi / Finnish

Lietuviu kalba / Lithuanian

Latviesu valoda / Latvian

Eesti / Estonian

Elinika / Greek

Slovenčina / Slovak

Slovenščina / Slovene

中文 / Chinese

български (Bălgarski) / Bulgarian

Română / Romanian

Magyar / Hungarian

Čeština / Czech



Instructions

2 | © Danfoss | DCS (CC) | 2018.03

8510196P04H - FRCC.PI.049.A4.02

The compressor must only be used for its

designed purpose(s) and within its scope of

application (refer to «operating limits»).

Consult Application guidelines and data-

sheet available from cc.danfoss.com

The compressor is delivered under

nitrogen gas pressure (between 0.3

and 0.7 bar) and hence cannot be

connected as is; refer to the «assembly»

section for further details.

Under all circumstances, the

EN378 (or other applicable local safety

regulation) requirements must be

fullled.

The compressor must be handled

with caution in the vertical position

(maximum oset from the vertical :

15°)

Refrigerant

Oil

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

High side

pressure range

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Low side

pressure range

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

Discharge temperature must be kept lower than 130°C

* When MT compressors are used with R417A, the factory charged mineral oil 160P must be replaced by polyolester oil 160PZ-175PZ.

** R407A and R407F are not used for China Market.

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

Installation and servicing of the compressor by qualied personnel only. Follow these instructions and sound refrigeration engineering practice relating to

installation, commissioning, maintenance and service.

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Never operate compressors without

terminal cover tted

A: Model number D: Supply voltage, Starting current & Maximum current

B: Serial number E: Housing service pressure

C: Certication logo: Contact Danfoss F: Factory charged lubricant

TH : Thermostat SR : Start Relay

SC : Start Capacitor RC : Run Capacitor

IOL : Motor Protector

HM8-40

15 Nm

HM12-50

Danfoss reciprocating compressors

MT / MTZ / NTZ / VTZ

Instructions

8510196P04H - FRCC.PI.049.A4.02

1 - Introduction

These instructions pertain to the Maneurop® MT,

MTZ,VTZ & NTZ compressors used for refrigera-

tion systems. They provide necessary informa-

tion regarding safety and proper usage of this

product.

2 – Handling and storage

• Handle the compressor with care. Use the

dedicated handles in the packaging. Use the

compressor lifting lug and use appropriate

and safe lifting equipment.

• Store and transport the compressor in an

upright position.

• Store the compressor between -35°C and

50°C.

• Don’t expose the compressor and the packa-

ging to rain or corrosive atmosphere.

3 – Safety measures before assembly

Never use the compressor in a ammable at-

mosphere.

• The compressor ambient temperature may

not exceed 50°C during o-cycle.

• Mount the compressor on a horizontal at

surface with less than 3° slope.

• Verify that the power supply corresponds to

the compressor motor characteristics (see

nameplate).

• When installing MTZ,VTZ or NTZ, use equip-

ment specically reserved for HFC refrigerants

which was never used for CFC refrigerants.

• Use clean and dehydrated refrigeration-grade

copper tubes and silver alloy brazing material.

• Use clean and dehydrated system components.

• The piping connected to the compressor must

be exible in 3 dimensions to dampen vibrations.

4 - Assembly

• Slowly release the nitrogen holding charge

through the schrader port.

• Remove the gaskets when brazing rotolock

connectors.

• Always use new gaskets for assembly.

• Connect the compressor to the system as

soon as possible to avoid oil contamination

from ambient moisture.

• Avoid material entering into the system while

cutting tubes. Never drill holes where burrs

cannot be removed.

• Braze with great care using state-of-the-art tech-

nique and vent piping with nitrogen gas ow.

• Connect the required safety and control de-

vices. When the schrader port is used for this,

remove the internal valve.

5 – Leak detection

Never pressurize the circuit with oxygen or

dry air. This could cause re or explosion.

• Do not use dye for leak detection.

• Perform a leak detection test on the complete

system.

• The low side test pressure must not exceed 25

bar.

• When a leak is discovered, repair the leak and

repeat the leak detection.

6 – Vacuum dehydration

• Never use the compressor to evacuate the

system.

• Connect a vacuum pump to both the LP & HP

sides.

• Evacuate the system to a pressure of 500 µm

Hg (0.67 mbar) absolute.

• Do not use a megohmmeter nor apply power

to the compressor while it is under vacuum as

this may cause internal damage.

7 – Electrical connections

• Switch o and isolate the main power supply.

See overleaf for wiring details.

• The compressor is protected against excess

current and temperature by an internal over-

load protector. Follow local regulations regar-

ding power line protection. The compressor

must be connected to earth.

• All electrical components must be selected as per

local standards and compressor requirements.

8 – Filling the system

• Keep the compressor switched o.

• Fill the refrigerant in liquid phase into the

condenser or liquid receiver. The charge must

be as close as possible to the nominal system

charge to avoid low pressure operation and

excessive superheat.

• Keep the refrigerant charge below 2.5 kg per

compressor cylinder if possible. Above this

limit; protect the compressor against liquid

ood-back with a pump-down cycle or suc-

tion line accumulator.

• Never leave the lling cylinder connected to

the circuit to avoid overlling.

9 – Verification before commissioning

Use safety devices such as safety pressure

switch and mechanical relief valve in compliance

with both generally and locally applicable regu-

lations and safety standards. Ensure that they

are operational and properly set.

Check that the settings of high-pressure swit-

ches and relief valves don’t exceed the maximum

service pressure of any system component.

• A low-pressure switch is recommended to

avoid vacuum operation. Minimum setting

0.1 bar.

• Verify that all electrical connections are pro-

perly fastened and in compliance with local

regulations.

• When a crankcase heater is required, it must be

energized at least 12 hours before initial start-

up and start-up after prolonged shutdown.

10 – Start-up

• All service valves must be in the open position.

• Balance the HP/LP pressure.

• Energize the compressor. It must start

promptly. If it does not, switch it o

immediately. Possible single phase miswiring

can cause burn-out within seconds.

• If the compressor does not start, check wiring

conformity and voltage on terminals.

• If the internal overload protector trips out, it

must cool down to 60°C to reset. Depending

on ambient temperature, this may take up to

several hours.

11 – Check with running compressor

• Check current draw and voltage.

• Check suction superheat to reduce risk of

slugging.

• When a sight glass is provided observe the oil

level at start and during operation to conrm

that the oil level remains visible.

• Respect the operating limits as printed overleaf.

• Check all tubes for abnormal vibration. Move-

ments in excess of 1.5 mm require corrective

measures such as tube brackets.

• When needed, additional refrigerant in the

liquid phase may be added in the low-pressure

side as far as possible from the compressor.

The compressor must be operating during

this process.

• Do not overcharge the system.

• Never release refrigerant to the atmosphere.

• Before leaving the installation site, carry out

a general installation inspection regarding

cleanliness, noise and leak detection.

• Record type and amount of refrigerant charge

as well as operating conditions as a reference

for future inspections.

12 - Maintenance

Internal pressure and surface temperature

are dangerous and may cause permanent inju-

ry.Maintenance operators and installers require

appropriate skills and tools. Tubing temperature

may exceed 100°C and can cause severe burns.

Ensure that periodic service inspections to

ensure system reliability and as required by local

regulations are performed.

To prevent system related compressor problems,

following periodic maintenance is recommended:

• Verify that safety devices are operational and

properly set.

• Ensure that the system is leak tight.

• Check the compressor current draw.

• Conrm that the system is operating in a way

consistent with previous maintenance re-

cords and ambient conditions.

• Check that all electrical connections are still

adequately fastened.

• Keep the compressor clean and verify the ab-

sence of rust and oxidation on the compres-

sor shell, tubes and electrical connections.

13 - Warranty

Always transmit the model number and serial nu-

mber with any claim led regarding this product.

The product warranty may be void in following

cases:

• Absence of nameplate.

• External modications; in particular, drilling,

welding, broken feet and shock marks.

• Compressor opened or returned unsealed.

• Rust, water or leak detection dye inside the

compressor.

• Use of a refrigerant or lubricant not approved

by Danfoss.

• Any deviation from recommended instruc-

tions pertaining to installation, application or

maintenance.

• Use in mobile applications.

• Use in explosive atmospheric environment.

• No model number or serial number trans-

mitted with the warranty claim.

14 – Disposal

Danfoss recommends that compressors

and compressor oil should be recycled

by a suitable company.

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This

also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specications already agreed. All trade-

Page is loading ...

Anleitung

6 | © Danfoss | DCS (CC) | 2018.03

8510196P04H - FRCC.PI.049.A4.03

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Den Verdichter nur bei angebrachter Klem-

menabdeckung betreiben.

A: Modellnummer D: Versorgungsspannung, Anlaufstrom, Maximalstrom

B: Seriennummer E: Betriebsdruck Gehäuse

C: Zertizierung Logo: F: Werkseitig eingefülltes Schmiermittel

Bitte wenden Sie sich an Danfoss

TH : Thermostat SR : Startrelais

SC : Anlaufkondensator

RC : Betriebskondensator

IOL : Motorschutzschalter

HM8-40

15 Nm

HM12-50

Der Verdichter darf nur für den vorgesehe-

nen Verwendungszweck und innerhalb seines

Anwendungsbereichs zum Einsatz kommen (sie-

he „Einsatzgrenzen“).

Siehe Anwendungsrichtlinien und Datenblätter auf

cc.danfoss.com.

Der Verdichter wird mit unter Druck ge-

setztem Stickstogas (zwischen 0,3 und

0,7 bar) geliefert und kann daher nicht

unmittelbar angeschlossen werden. Sie-

he Abschnitt „Zusammenbau“ für weitere

Angaben.

Unter allen Umständen

müssen die Anforderungen der EN

378 (oder eine andere zutreende

nationale Sicherheitsnormen)

erfüllt werden.

Der Verdichter darf nur vorsichtig in

vertikaler Position gehandhabt und

transportiert werden (max. Schrän-

kung 15 °)

Installation und Wartung des Verdichters darf nur von qualiziertem Fachpersonal durchgeführt werden. Diese Anleitung befolgen und bei Installation, Inbe-

triebnahme, Wartung und Service gemäß gängiger Kältetechnikpraxis vorgehen.

Danfoss Hubkolben-Verdichter

MT / MTZ / NTZ / VTZ

Betriebsgrenzen

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

Druckbereich

Hochdruckseite

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Druckbereich

Niederdruckseite

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

Die Druckrohrtemperatur darf 130 °C nicht überschreiten.

* Wenn MT-Verdichter in Verbindung mit R417A verwendet werden, muss das werkseitig eingefüllte Mineralöl 160P durch das Polyesteröl 160PZ-175PZ ersetzt werden.

** R407A und R 407F wird nicht im chinesichen Markt verwendet.

Page is loading ...

Instrucciones

8 | © Danfoss | DCS (CC) | 2018.03

8510196P04H - FRCC.PI.049.A4.05

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Nunca ponga en marcha los compresores sin la

tapa de terminales instalada.

A: Número de modelo D: Tensión de alimentación, corriente de arranque,

corriente máxima

B: Número de serie E: Presión de servicio de la carcasa

C: Logo de certicación: F: Carga de lubricante de fábrica

Póngase en contacto con Danfoss

TH: termostato

SR: relé de arranque

SC: condensador de arranque

RC: condensador de funcionamiento

IOL: protector del motor

HM8-40

15 Nm

HM12-50

Este compresor solamente debe utilizarse para su(s)

cometido(s) designado(s) y dentro de su campo de

aplicación (consulte “límites de funcionamiento”).

Consulte las Guías de aplicación y Especicaciones

técnicas disponibles en cc.danfoss.com

Este compresor se suministra con

gas nitrógeno a presión (entre 0,3

y 0,7 bar) y, por lo tanto, no puede

conectarse tal cual; consulte la

sección «montaje», para más

información.

En todas las circunstancias,

deben cumplirse los requisitos de

la norma EN378 (u otras normas

locales de seguridad aplicables).

Este compresor se debe manipular

con precaución y en posición vertical

(desviación máxima de la posición

vertical: 15°)

La instalación y el mantenimiento del compresor deben ser realizadas únicamente por personal cualicado. Siga estas instrucciones y las prácticas de ingenie-

ría de refrigeración adecuadas respecto a instalación, puesta en marcha, mantenimiento y servicio técnico.

Danfoss Compresores alternativos

MT / MTZ / NTZ / VTZ

Límites de funcionamiento

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

Rango de presión

en el lado de alta

presión

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Rango de presión

en el lado de baja

presión

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

La temperatura de descarga se debe mantener por debajo de 130 °C

* Cuando los compresores MT se utilizan con R417A, el aceite mineral de fábrica 106P debe reemplazarse por aceite de polioléster 160PZ-175PZ.

** R407A y R407F no se utilizan en el mercado Chino.

Page is loading ...

Istruzioni

10 | © Danfoss | DCS (CC) | 2018.03

8510196P04H - FRCC.PI.049.A4.06

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Non mettere mai in funzione i compressori se

sprovvisti di coperchio coprimorsetti

A: Numero di modello D: Tensione di alimentazione, corrente di avviamento e corrente

massima

B: Numero di serie E: Pressione di esercizio

C: Certicazione Logo: Contattare Danfoss F: Lubricante caricato in fabbrica

TH : Termostato

SR : Relè di avviamento

SC : Condensatore di avviamento

RC : Condensatore di marcia

IOL : Protezione motore

HM8-40

15 Nm

HM12-50

L’installazione e la manutenzione del compressore devono essere eettuate solo da personale qualicato. Seguire queste istruzioni e le corrette procedure

relative a installazione, messa in servizio, manutenzione e riparazione degli impianti di refrigerazione.

Il compressore deve essere utilizzato solo per gli

scopi per i quali è progettato e che rientrano nel suo

ambito di applicazione (fare riferimento ai «limiti

operativi»).

Consultare le linee guida per l’applicazione e la scheda

tecnica disponibili su cc.danfoss.com

Il compressore viene consegnato sotto

pressione di gas di azoto (compresa tra

0.3 e 0.7 bar) e pertanto non può essere

collegato così com’è; fare riferimento

alla sezione «montaggio» per maggiori

dettagli.

In qualsiasi circostanza si dovranno

soddisfare i requisiti EN378 (o altra nor-

ma locale applicabile sulla sicurezza).

Il compressore deve essere movimen-

tato con cautela in posizione verticale

(scostamento massimo dalla verticale:

15°)

Compressore alternativo Danfoss

MT / MTZ / NTZ / VTZ

Limiti operativi

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

Campo del lato di

alta pressione

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Campo del lato di

bassa pressione

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

La temperatura di scarico deve essere inferiore a 130°C

* Quando i compressori MT sono usati con R417A, l’olio minerale caricato in fabbrica 160P deve essere sostituito da olio poliestere 160PZ-175PZ.

** R407A e R407F non sono utilizzati per il mercato Cinese.

Page is loading ...

Instruções

8510196P04H - FRCC.PI.049.A4.28

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Nunca opere os compressores com a cobertura dos

terminais levantada

A: N° do Modelo D: Tensão, corrente de partida e corrente máxima

B: N° Serial E: Pressão de serviço

C: Logótipo de Certicação: F: Lubricante carregado de fábrica

Entre em contato com a Danfoss

TH: Termostato SR: Relé de Partida

SC: Capacitor de Partida

RC: Capacitor de Marcha

IOL: Protetor do Motor

HM8-40

15 Nm

HM12-50

A instalação e manutenção do compressor deverá ser efetuada somente por pessoal qualicado. Siga estas instruções assim como as boas práticas de engenharia de

refrigeração no que diz respeito à instalação, partida do equipamento, assistência e manutenção.

O compressor só pode ser usado para os ns

a que se destina e dentro do respectivo âmbito de

aplicação (consulte os «limites de operação»).

Consulte as orientações de Aplicação e as folhas de

dados disponíveis em cc.danfoss.com

O compressor é entregue com nitro-

gênio sob pressão (entre 0,3 e 0,7 bar)

pelo que não pode ser ligado tal como

é fornecido; consulte a seção «monta-

gem» para mais detalhes.

Em todas as circunstâncias deverão

ser respeitadas as diretrizes EN378 (ou

outros regulamentos de segurança

locais que se apliquem).

O compressor deverá ser manuseado

com precaução e na posição vertical

(deslocamento máximo da posição ver-

tical : 15°)

Danfoss compressores

MT / MTZ / NTZ / VTZ

Limites de operação

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

Intervalo de pressão

do lado de alta

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Intervalo de pressão

do lado de baixa

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

A temperatura de descarga deverá ser mantida abaixo de 130°C

* Quando os compressores MT são utilizados com R417A, a carga de fábrica de óleo mineral 160P deve ser substituída por óleo poliolester 160PZ-175PZ.

** Os uidos R407A e R407F não são utilizados no mercado chinês.

Page is loading ...

Instrukcje

8510196P04H - FRCC.PI.049.A4.49

1" : 80 Nm

1"1/4 : 90 Nm

1"3/4 : 110 Nm

IOL

230 V

IOL

1 ~ PSC

~ CSR

230 V

IOL

Nigdy nie uruchamiać sprężarek bez zamonto-

wanej osłony puszki zaciskowej

A: Oznaczenie modelu D: Napięcie zasilania, prąd rozruchowy, max. prąd pracy

B: Numer seryjny E: Maksymalne ciśnienie robocze obudowy

C: Certykat logo: F: Typ oleju

Skontaktuj się z rmą Danfoss

TH : Termostat

SR : Przekaźnik rozruchowy

SC : Kondensator rozruchowy

RC : Kondensator roboczy

IOL : Zabezpieczenie silnika

HM8-40

15 Nm

HM12-50

Instalacji i serwisu sprężarki dokonuje wyłącznie wykwalikowany personel. Należy postępować zgodnie z poniższymi instrukcjami i zasadami dobrej prak-

tyki inżynierskiej w chłodnictwie, odnoszącymi się do instalacji, oddawania do użytku, konserwacji i serwisu.

Sprężarka może być wykorzystywana wyłącznie

w celu (celach), do jakiego (jakich) została

przeznaczona, obejmujących zakres jej zastosowań

(patrz „limity pracy ”).

Zapoznaj się z poradnikiem aplikacyjnym oraz z kartami

katalogowymi dostępnymi na stronie cc.danfoss.com

Dostarczona sprężarka znajduje się

pod ciśnieniem azotu (przedział od

0,3 do 0,7 bara), dlatego też nie może

być podłączana od razu; patrz paragraf

„montaż” w celu uzyskania dalszych

informacji.

W każdym przypadku należy

spełnić wymagania EN378 (lub innego

lokalnego przepisu bezpieczeństwa).

Sprężarkę należy przenosić ostrożnie

w pozycji pionowej (maksymalne

odchylenie od pionu: 15°)

Sprężarki Tłokowe Danfoss

MT / MTZ / NTZ / VTZ

Limity pracy

MT MTZ VTZ NTZ

R22 R417A* R407A** R407C R407F** R134a

R404A /

R507

R452A R448A R449A R513A R407C R134a

R404A/

R507

R452A

R404A/

R507

160P

160PZ-

175PZ*

175PZ-160PZ 175PZ 160PZ 175PZ

175PZ-

160Z/MPZ

Zakres ciśnienia

tłoczenia

bar (g)

10.9 -

27.7

9.32 -

25.5

11.6 -

25.8

12.5 -

29.4

12.1 -

24.0

7.87 -

22.6

13.2 -

27.7

12.5 -

27.3

11.7 -

26.0

11.7 -

25.9

8.37 -

23.36

7.8 -

29.4

7.87 -

20.2

9.89 -

27.7

12.5 -

24.2

13.2 -

27.7

Zakres ciśnienia

ssania

bar (g)

1.01 -

6.89

0.54 -

5.66

0.53 -

5.94

1.43 -

6.55

0.99 -

6.25

0.06 -

4.72

1.04 -

7.2

0.84 -

6.69

0.6 -

6.08

0.6 -

6.07

0.21 -

5.12

1.43 -

6.55

0.64 -

3.88

1.04 -

6.06

0.18 -

2.99

0.05 -

3.34

Temperatura tłoczenia nie może przekraczać 130°C

* W przypadku eksploatacji sprężarek MT z R417A, fabrycznie zalewany olej mineralny 160P należy wymienić na olej poliestrowy 160PZ-175PZ.

** R407A i R407F nie są stosowane na rynku chińskim.

Page is loading ...

8510196P04H - FRCC.PI.049.A4.ML

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This

also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specications already agreed. All trade-



Danfoss A/S

6430 Nordborg

Denmark