Blue Sea Systems 7860 Operating instructions

Brand: Blue Sea Systems

Model: 7860

Type: Operating instructions

Instructions

Sure Eject

™

Mounting Adapter Kit

7860

Blue Sea Systems, Inc.

4600 Ryzex Way

Bellingham, WA 98226 USA

p 360.738.8230

www.bluesea.com

980036520 Rev. 002

Installation Instructions

Assembly Instructions

1. Choose an installation location with a flat surface and a vehicle wall of 3/4" or less.

2. Use backing plate as cutout template, and cut mounting holes.

3. Peel one of the adhesive strips on the backing plate and start to peel the remaining

three, so small tabs of backing are available to grab.

4. Put the backing plate through the mounting hole, align the screw hole, and lightly

push the fully peeled adhesive to the back of the mounting surface.

IMPORTANT!

Adhesive is very sticky, and is activated by pressure. Only use light pressure until you are sure

plate is aligned with cutout.

5. While keeping the holes aligned, use the tabs created in step 2 and peel the

remaining adhesive strips, pressing them lightly onto the mounting surface.

6. Verify alignment of backing plate with cutout and then press firmly around the

backing plate to set adhesive.

7. Pass wires through cutout and connect to Sure Eject Assembly.

8. Install Sure Eject Assembly into the cutout hole, keeping gasket aligned with

mounting plate, and mount to vehicle body using supplied #10-32 x 1" screws.

Max. Torque 19 in-lb (2.1 N-m)

1. Removeprotectivelmfromfrontfaceofmountingplate.

2. Align Sure Eject, mounting plate, door seal, and door as shown, then secure using

included #8-32 x 7/8" screws. If installing without door, use #8-32 x 7/16" screws

(not included)

IMPORTANT!

Warranty void if incorrect screw length is used.

3. Place foam gasket over Sure Eject, against back of mounting plate,

before wiring Sure Eject.

Easily install 15A and 20A Sure Eject units from the outside of a vehicle.

Features

• Allows one person installation of Sure Eject

• No special shaped cutouts required

• Threaded backing plate secures Sure Eject to vehicle without added hardware

• Compatible with all 15A and 20A Sure Eject ejection units, with and

without covers (7850, 7850001, 7851, & 7851001)

Specications

Sure Eject Assembly Screws #8-32 x 7/8"

Max. Torque 10.8 in-lb (1.2 N-m) for #8-32 x 7/8" screws

Installation Screws #10-32 x 1"

Max. Torque 19 in-lb (2.1 N-m) for #10-32 x 1" screws

NOTE: Anti vibration thread-locker recommended.

Mounting Adapter Kit includes:

1. 1 x Mounting Plate

2. 4x #8-32 x 7/8" Assembly Screws

3. 1x Backing Plate

4. 4x #10-32 x 1" Installation Screws

5. 1x Foam Gasket for Face Plate

#10-32 x 1"

screw (x4)

Max. Torque:

19 in-lb (2.1 N-m)

Sure Eject Assembly

Vehicle Body

(up to 3/4" thick)

Backing Plate

Mounting Plate

Sure Eject Door Seal

#8-32 x 7/8"

Screws (x4)

Max. Torque:

10.8 in-lb (1.2 N-m)

Sure Eject

Door

7850, 7850001 (15A)

or 7851, 7851001 (20A)

Sure Eject

Foam Gasket

for Face Plate

Cutout Template

Use 13/64"

(or #6) drill bit

Cutout Area

Face Plate Outline

6.00"

(152.4mm)

Mounting

Screw

Centers

4.50"

(114.3mm)

Mounting Screw Centers

5.76"

(146.4mm)

4.29"

(109mm)

R .25" x 4

(6.4mm)

Use 0.5" (13mm)

drill bit for

correct radius

Blue Sea Systems 7860 Operating instructions

Blue Sea Systems 7860 Operating instructions

Blue Sea Systems 7860 Operating instructions

Related papers

Other documents