Haier HP200M1 Installation and Service Manual

Heat Pump Water Heater

Installation and Service Manual

Model

HP200M1

HP250M1

Please read this manual carefully prior to your use of this water heater.

The appearance of the water heater given in this manual is for reference only.



2

Contents

1. Product safety statement.......................................................................................................... 3

2. Functionings & principles .................................................................................................... 4

3. Technical parameters ............................................................................................................ 5

4. Description of parts and components ................................................................................. 6

5. Installation introduction ........................................................................................................11

6. Operating and settings.............................................................................................................. 13

7. Faults and protection ............................................................................................................... 26

8. Faults and protection .................................................................................................................17

9. The method of dismantling products ........................................................................................24

10. Repairs common tools ............................................................................................................29



3

1. Product safety statement

1. This appliance can be used by children aged from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

2. Children shall be closely supervised to make sure they stay away from this product.

3. The water may drip from the discharge pipe of the pressure relief device and this pipe must be

left open to the atmosphere.

Safety instructions (to be followed at any time)

Refrigerant: R134a; When handling product, you should

- No smoking

- Prevent the accumulation of electrostatic charges

- Work in a well ventilated place.

- Avoid contact with the skin and eyes

- Do not inhale the vapours

- Evacuate the hazardous area

- Stop the leakage



4

2. Functionings & principles

A low-pressure liquid refrigerant is vaporized in the heat pump's evaporator and passed into the

compressor. As the pressure of the refrigerant increases, so does its temperature. The heated

refrigerant runs through a condenser coil within the storage tank, transferring heat to the water

stored there. As the refrigerant delivers its heat to the water, it cools and condenses, and then

passes through an expansion valve where the pressure is reduced and the cycle starts over.



5

3. Technical parameters



6

4. Description of parts and components

Heat pump structure



7

Exploded view



He

a

1. C

The

and

to t

h

2. E

v

Eva

p

3. C

A c

o

con

d

a

t pump s

y

ompressor

compresso

r

compressed

i

h

e condenser

v

aporato

r

p

orato

r

effec

t

ondenser

o

ndenser: hi

g

d

ensation, th

e

y

stem co

m

is to effect

a

i

nto high te

m

heat exchan

g

t

s: it makes t

h

g

h-temperat

u

e

refrigerant

v

Wiring

b

ox

m

ponents

a

low-tempe

r

m

perature an

d

g

e

r

.

h

e liquid refr

i

u

re high-pres

s

v

apor discha

r

8

r

ature low-pr

e

d

pressure of

i

gerant abso

r

s

ure refriger

a

r

ge heat, the

h

e

ssure evap

o

the superhea

t

r

bs heat and i

s

a

nt vapor is

h

eat is absor

b

o

rato

r

refrige

r

t

ed vapo

r

, a

n

s

evaporated

condensed i

n

b

ed by the he

a

Inspirato

r

Exhaust p

i

r

ant vapo

r

s

u

n

d then disch

a

into steam.

n

to liquid, d

u

a

ting mediu

m

r

y pipe

i

pe

u

cked

a

rged

u

ring

m

.



4. T

h

The

pres

the

t

5. F

i

It’s

i

can

6.

H

Hig

h

syst

e

7. S

e

Ser

v

nee

d

h

ermal expa

n

refrigerant

p

sure is redu

c

t

hrottling pro

i

lte

r

i

nterio

r

has a

filter out im

p

H

igh Voltage

S

h

-voltage sw

i

e

m compone

n

e

rvice valve

v

ice valve is

d

le, sales sta

ff

n

sion valve:

p

asses throu

g

c

ed to the ev

a

cess.

filter and de

p

urities in the

S

witchgea

r

i

tch is to pr

e

n

ts, high-pre

s

mainly use

d

ff

can vacuu

m

g

h the ther

m

a

poration pr

e

siccant, the

d

refrigerant.

e

vent excessi

v

s

sure of the

h

d

for filling

r

m

infusion re

fr

9

m

al expansio

n

e

ssure, part

o

d

esiccant abs

o

v

e pressure

i

h

igh-voltage

s

r

efrigerant, a

f

fr

igerant fro

m

n

valve, the

p

o

f the refrige

r

o

rbs moistur

e

i

n the syste

m

s

witch is 2.8

M

f

ter removin

g

m

here.

p

ressure fro

m

r

ant will eva

p

e

fro

m

the re

f

m

, thus affect

i

M

Pa.

g

the nuts, i

t

m

the conde

n

p

orate into

g

f

rigerant, the

i

ng the life

o

t

contains a

v

n

sing

g

as in

filte

r

o

f the

v

alve



8. F

a

It f

o

effi

c

9.

M

T

h

a

n

o

rced air thr

o

c

iency of the

M

otor

h

e role of th

e

o

ugh the duc

t

heat exchan

g

e

axial fan m

o

t

, and then f

l

g

er.

o

tor is driven

Se

r

nuts

10

l

ows through

axial fan bl

a

r

vice valve

a heat exch

a

des rotate.

a

nger to imp

r

ove heat tr

a

nsfer



9.

R

Hea

t

can

s

5.

I

Not

e

1. P

r

2.

V

a

3. L

o

4.

Va

5. P

r

Pip

e

R

efrigerant

t

pump refri

g

s

appearance

I

nstalla

t

e

:

r

essure relie

f

V

a

lve are not i

o

cal water c

o

Va

lves with N

F

r

essure relie

f

e

line install

a

g

erant is R13

4

is as follows

:

t

ion intr

o

f

valve, ther

m

ncluded in t

h

o

nsumption c

o

F

markings a

r

f

valves shall

a

tion diagra

m

4

a, ODP val

u

:

o

ductio

n

m

ostatic valve

h

e scope of s

u

o

nditions;

r

e recomme

n

be installed

i

m

:

11

u

e is 0, no d

a

n

, stop valve,

c

u

pply, please

n

ded in Franc

i

f pressure o

f

a

mage to the

c

heck valve

a

select prope

r

e;

f

water suppl

y

ozone layer.

a

nd French c

o

r

fittings as p

e

y

exceeds 6 b

a

R134a refri

g

o

mbination

er

ars.

g

erant



12

Installation precautions:

1. Water heaters shall be equipped with a dedicated power line and residual current circuit

breakers. The action current shall not exceed 30 mA;

2. The ground line and the zero line of the power supply shall be separated entirely.

3. Connecting the zero line to the ground line is not allowed.

4. Parameter of the power line: 3 1.5mm² or more.

5. If a power cable is damaged, it shall be replaced by qualified professionals to avoid risks.

6. In the case of places and walls where water may be splashed to, installation height of a power

socket shall not be less than 1.8 m, and it shall be ensured that water would not be splashed on

these places. The socket shall be installed out of children’s reach.

7. The phase line, zero line and ground line inside a power socket used in your home shall be

wired correctly without any wrong positioning or false connection, and internal short circuit shall

be avoided. Wrong wiring may cause fire accidents.



13

Wiring diagram

6. Operation and functions

Display



14

1. Key functions

A.

Main switch: time and specific water temperature are indicated after machine is switched off;

COMF mode is activated after starting the machine and icon lights.

B.

Mode key: it is used for working mode selection (COMF/ECO/VAC).

C.

Setting key: this key is used to set ECO (economy mode) time slot and VAC (vacation mode)

days.

D.

Time setting. Press TIMER key and the hour lights up. The time can be adjusted

together with - and + key, and the flashing will stop if there is no key action for 6

seconds. Press TIMER key again before the flashing stops, the minute flashes, for

which the setting method is the same as above.

E.

Quick heating function key: press this key and BOOST icon lights up and the quick heating mode

is activated. Heat-pump and electric heating are activated at the same time.

2. Indication

A. COMF comfort mode : starts the heat-pump to make temperature of the water tank reach the set

level, and performs heat preservation after heating. Heat-pump start is at a priority level.

1) The default temperature for the first start is set at 55 C, which may be adjusted via +

and - . The temperature can be adjusted between 35-75 ; the heat-pump can be heated up to

65 , beyond which the electric heater will be activated.

2) Within an ambient temperature range of 7-35 C, the heat-pump is the first to be started by the

system for heating. The heat-pump will not start if the temperature is out of this range, but the

electric heating will be activated.

B. ECO economy electricity consumption mode : during the economy electricity consumption

period, the heat-pump is activated for hot water supply.

1) Introduction to economy function:

Heating is started in the economy period, and heat preservation, which will not be continued if it is

not in the economy period, is carried out after heating. If heating is not completed within the

economy period, it will be kept on until the set temperature is reached.

2) Economy time setting

After entering this mode, press SET key to set the economy time, and the 2-digit temperature

shows LP. ON lights up, hour flashes; press + and - to set the hour right now.



15

Then press SET again, "minute will flash; press + and - to adjust the minute setting.

Press SET key again, ON stops lighting, OFF lights up. If no key action occurs after

flashing for 6 seconds, the above adjustment will be confirmed (other keys, whose original

functions stop functioning temporarily, can also be pressed for confirmation while flashing). The

default economy time period is 00:00 07:00.

C. VAC vacation mode icon : hot water is provided in advance in accordance with the return date

input by users.

1) Vacation day setting

Enter into VAC mode. The 2-digit temperature flashes and shows OO , press + and - right

now to set vacation days (the range is between 1 and 99 days); press SET key for confirmation.

No heating is carried out if OO is indicated.

2) VAC mode introduction

According to user-defined number of vacation days, finished 0:00 on vacation begin heating to 65

degrees, this temperature is not adjustable.

(1) The program starts from the confirmation of the setting. The VAC mode can not be scheduled

in advance

(2) After completion of the vacation mode, ECO mode will be activated automatically;

3) Example of vacation setting

For example, you set vacation days on January 1st and return home from vacation on January 5th.

The date shall be set as (5-1) =4 days, and corresponding temperature shall also be set. The

heat-pump will start heating on 00:00 o clock of January 5

th

automatically.

D.Quick heating mode icon “BOOST”: this icon will light up if quick heating function is

activated.Heat-pump and electric auxiliary unit are activated at the same time for heating.

Temperature icon “HW Left” : indicates set temperature and current temperature. Residual hot

water quantity icon : indicates the residual hot water quantity in the water tank.

Timer and preset state icon : indicates current time or preset time slot.

3. Control functions

A. Electrical leakage protection

The control system of this machine features an electricity leakage protection function.

B. 10-minutes protection

When starting the machine immediately after electricity input, the fan and the compressor will

start at the same time. When starting the machine immediately after shutdown, the machine unit

goes into the protection mode and starts after 10 minutes, which is considered to be normal.

C. Automatic defrosting function

The defrosting mode is automatically activated if the ambient temperature is too low and after the

compressor already runs continuously for a certain period.

D. Protection for nonconformist operation



16

The permissible ambient temperature for the heat-pump mode is between 7 C~35 C.

E. Overload protection function for water heaters

The working load of the compressor will be heavy if temperature is high in summer. In order to

meet hot water requirements of users and to lengthen service life of the compressor, this product

automatically adjusts the fan speed to ensure reliable operation of the compressor.

F. Anti-freezing function

The heat-pump starts heating to avoid freezing of the water tank if the temperature in the water

tank is too low.

G.The default temperature of this water heater is 55 C.

Function of the number of occupants, the temperature should be set as below; please raise the set

temperature if a more comfort is required.

H. Anti-legionella function:

This machine is equipped with a sterilization function, which is activated every 14 days to heat the

water tank to 65 C automatically to realize sterilization.

7. Checking and maintenance

Cleaning and maintenance of the water tank

Shut down the machine and cut off the power supply

Do not touch with wet hands

Do not clean with hot water or solvent

1. Safety valve maintenance

Rotate the safety valve handle once a month. The valve works well if there is water flowing out,

otherwise check for blocking and replace the safety valve if necessary.

2. Drain the water tank to empty

Cut off power supply and shut down water inlet valve, then drain the water tank to empty via the

sewage outlet. Please stay away from the sewage outlet if there is hot water inside the water tank

to avoid injury.

3. Replacement of the anode bar

The protective anode equipped for Haier heat-pump water heaters can prolong service life of its

products effectively. The magnesium anode, which shall be replaced in time, shall be checked

typically once every 2 years according to different water qualities.



17

4. Cleaning of the air filter:

The filter may be dedusted and cleaned every 3-6 months according to service conditions and dirt

accumulation. It is located at the top of the water heater and can be pulled out by holding the filter

handle upwards.

8. Faults and protection



18

Fault code identification method



19



20

Page is loading ...

Haier HP200M1 Installation and Service Manual

This manual is also suitable for

Haier HP200M1 Installation and Service Manual

Related papers

Other documents