2. Computers & electronics
  3. TVs & monitors
  4. Wall & ceiling mounts accessories
  5. Toro
  6. 137-5580
137-5580

Toro 137-5580 User manual

  • Hello! I've read the Wing Mount Kit Installation Instructions for the Groundsmaster 4000 Series 137-5580. This document provides a detailed guide for installing the mounting kit, with a parts list and sequential steps for installation. The text also highlights the importance of safety measures before starting the process. I am ready to answer your questions regarding this document and the installation on your machine.
  • What should I do before starting the installation?
    What is the torque for bolts that secure the deck mount to the cutting unit?
    What is the torque for installing the hydraulic cylinder to the deck mount?
FormNo.3422-333RevA
WingMountKit
Groundsmaster®4000SeriesRotaryMower
ModelNo.137-5580
InstallationInstructions
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
DescriptionQty.Use
Nopartsrequired–Preparethemachine.
Deckmount1
Plate1
Springpin1
Spacer2
Bolt(3/4x4-1/2inches)1
Locknut(3/4inch)1
Cabletie1
Installthekit.
Determinetheleftandrightsidesofthemachinefrom
thenormaloperatingposition.
PreparingtheMachine
1.Parkthemachineonalevelsurface.
2.Disengagethepowertakeoffandlowerthe
attachments.
3.Engagetheparkingbrake.
4.Shutofftheengineandremovethekey.
5.Waitforallmovementtostop.
6.Allowmachinecomponentstocool.
©2021—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3422-333*
InstallingtheDeckMount
1.Removethesnapringsonbothsidesofthe
U-jointasshowninFigure3.
2.Removethecapsunderthesnaprings.Thiscan
bedonebyaddingmoregreaseintotheU-joint.
3.Removetheexistinglongbolt(Figure3).
4.Removetheplateandrubbercushion(Figure
3).Discardtheplate.
5.Removetheboltsthatholdthedeckmountto
thecuttingunit(Figure3).
6.Removethebolt,locknut,andspacersthat
securethehydrauliccylindertothedeck
mount.Discardthehardwareandexistingdeck
mount(Figure3).
g367529
Figure1
1.Existingdeckmount6.Locknut(3/4inch)
2.Longbolt7.Bolt(3/4x4-1/2inches)
3.Snapring8.Bolt
4.Plate9.Lockwasher
5.Rubbercushion10.Washer
7.Usingthenewdeckmountasatemplate,locate
anddrilla9/16inchholeintotherearplateson
thecuttingunitasshowninFigure2.
g365598
Figure2
1.102mm(4inches)3.Drilla9/16inchhole
2.36mm(1-13/32inches)4.Deckmount
8.Placethenewdeckmountontothecuttingunit.
9.Installtheboltsthatsecurethedeckmountto
thecuttingunit(Figure3andFigure4);torque
to102N∙m(75ft-lb).
2
g365599
Figure3
1.Springpin7.Spacer
2.Snapring8.Bolt(3/4x4-1/2inches)
3.Rubbercushion9.Bolt
4.Plate10.Lockwasher
5.Deckmount11.Washer
6.Locknut(3/4inch)
g365601
Figure4
1.Installeddeckmount
10.InstalltheU-jointcapsandsecurethemwiththe
previouslyremovedsnaprings(Figure3).
11.Installthehydrauliccylindertothedeckmount
withabolt(3/4x4-1/2inches),locknut(3/4
inch),andspacers(Figure3);torqueto136N∙m
(100ft-lb).
12.Installthecabletie(Figure5).
g365600
Figure5
1.Cabletie
13.Startthemachineandchecktheoperationof
thecuttingunit.Ensurenohosesrubagainst
themachineandifneeded,adjustthehoses.
3
/