PowerMax MFT-410 Owner's manual
- Type
- Owner's manual
MFT-410
4 IN 1 MULTIFUNCTION TREADMILL
OWNER’S MANUAL
Read all instructions carefully before using this product. Retain this owner's manual
for the future's reference. Product may be slightly different with photos, it is subject
to actual product.
www.powermaxfitness.net
2
TABLE OF CONTENTS
WARRANTY 2
IMPORTANT SAFETY NOTICE 3
PARTS LIST 5
ASSEMBLY INSTRUCTION 6
STORAGE AND MAINTENANCE 12
1 YEAR LIMITED WARRANTY
PowerMax Fitness warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it has
been installed and operated in accordance with PowerMax Fitness's Owner's Manual. PowerMax
Fitness's obligation under this warranty is limited to replacing or repairing, free of charge, any
parts which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application. From the date of
purchase, the frame is warranted to be free from defects for 1(one) year*.
Customer Care
Phone: +91-8080-206-206
Email: support@powermaxfitness.net
Support / Complaint Generation: support.powermaxfitness.net
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase
* Terms and Conditions Apply. For T&C visit www.powermaxfitness.net
www.powermaxfitness.net
3
IMPORTANT SAFETY NOTICE
ATTENTION: Although the treadmill is considered as much as possible the safety during the design
and manufacture, but still need obey some safety precautions during use, please read this manual
carefully before assemble and use this treadmill, especially the below safety precautions:
1. Keep the children and pets away from the product at all times, DO NOT leave unattended
children in the same room with the machine.
2. Only allow one person use the machine one time.
3. If the user experiences dizziness, nausea, chest pain or any other abnormal symptoms,
STOP the workout at once! CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the treadmill on a clear, level surface, DO NOT use near water or outdoors,
5. Hands not close to any transmission parts during use.
6. Always wear appropriate workout clothing when exercising. Running or aerobic exercising
shoes are also required.
7. DO NOT place any sharp objects around the treadmill.
8. Handicapped or disabled person should not use the treadmill without presence of a
qualified health professional or physician.
9. Before use make sure that all the parts or units are securely tightened. If you find any
defective parts, keep the treadmill out of use until well repaired.
10. Before exercising, always do stretching exercise first.
11. NEVER operate the treadmill if it is not functioning properly.
12. Keep the training record well for your reference.
13. The max user weight for the product is 120kg. It is not designed for therapeutic use!
14. If necessary, you can ask someone help to assemble the treadmill.
WARNNING: Please consult the doctor before use this treadmill. It is important for the persons
whose age is more than 35 or have any illness. Read all the using and operating instruction
carefully before do any exercise. Our company will not take any responsibility for any damage
which caused by himself.
www.powermaxfitness.net
4
EXPLOSIVE VIEW
www.powermaxfitness.net
5
PARTS LIST
Part No. Part name/specification QTY.
Part No. Part name/specification QTY.
1 Monitor 1 22L/R L/R pedal tube 2
2 Front Handle bar 1 23L/R L/R pedal 2
3 Hexagon head bolt
M10*40*25 1 24 Hexagon head bolt M10*15 2
4 Flat washer (1)20* (1)10.5*2.0 5 25 Hexagon head boltM10*55*30
2
5 Hexagon socket head bolt
M8*80*30 2 26 Carriage bolt M8*45*20 6
6 Arc washer (1)20*(1)8.5*2.0 4 27L/R L/R upright 2
7 Cross head screw M5*10 2 28 Base frame 1
8 Flat washer 012*05.5*1.0 2 29 Pulling pin 1
9 Central upright 1 30 Hexagon socket head bolt
M8*50*25
10 Nylon nut M8 18 31 Body twister set 1
11 Hexagon socket head bolt
M8*35*20 2 32 Adjustment tube 1
12 U shape bracket 1 33 Flywheel cover 1
13 Grip pulse wire 1 2 34 Cross head screw M5*12 2
14 Grip pulse wire 2 2 35 Main frame 1
15 Grip pulse post 2 36 Sensor wire lower 1
16 Sensor wire upper 1 37 Sensor wire middle 1
17 Hexagon socket head bolt
M8*20 4 38 Push-up bar 2
18 Flat washer c1)20*c1)8.5*2.0 26 39 Hexagon socket head bolt
M8*45*40 4
19 Oil cylinder 2 40 Hexagon head bolt M6*40*20 4
20 Pulley set 1 41 Cross wrench 1
21 Hexagon socket head bolt
M8*40*20 3 42 Allen wrench 1
www.powermaxfitness.net
6
ASSEMBLY INSTRUCTION
Step 1.
Fix L/R upright (27L/R) and Central upright (9) to Base frame (28) with Carriage bolts (26), Flat
washers (18), Nylon nuts (10). Don't tighten the bolts, nuts and screws securely one time, also
including the following assembly step.
www.powermaxfitness.net
7
Step 2.
1. Using Hexagon head bolts (25) and flat washers (4), install frame (35) to L/R upright (27L/R).
2. Fix the Adjustment tube (32) to the Main frame (35) and Base frame (28) with Hexagon
socket head bolt (30) and (21), Flat washers (18), Nylon nuts (10).
3. Fix the Flywheel cover (33) to the Main frame (35) with 2pcs Cross screws (34). 4.Connect
the Sensor wire lower (36) with Sensor wire middle (37).
www.powermaxfitness.net
8
Step 3.
1. Assemble the U shape bracket (12) onto the Central upright (9) with 1pcs Hexagon head
bolt (3), flat washer (4).
2. Connect the Sensor wire middle (37) with Sensor wire upper (16).
3. Connect the Grip pulse wire1(13) with Grip pulse wire2 (14). Push the Grip pulse post (15)
into the U shape bracket (12) with the connected wires hiding the inside of posts. Align the
holes of the three parts (27R,12,15) and screw the Hexagon socket head bolt (11) in. (Don't
trap the sensor wires. If they block the holes, please use the Allen wrench (42) to push them
aside.)
4. Repeat the above for the assembly of Part 27L,12,15
www.powermaxfitness.net
9
Step 4.
1. Install L/R pedal tube(22L/R) to the Central upright (9) with 2 sets Hexagon socket head
bolts (17) and Flat washers (18).
1. Fix the two Oil cylinders (19) to the L/R pedal tube with 2 sets Hexagon socket head bolt
(21), Flat washers (18), Nylon nuts (10).
2. Fix the Oil cylinders (19) to the Central upright (9) and tighten them with 2 sets Hexagon
socket head bolts (17) and Flat washers (18).
3. Insert the hook of Pulley set (20) into the hole of the Central upright (9) first. Then screw
the steel cable of the Pulley set (20) to the L/R pedal tube(22L/R) with 2 sets Hexagon head
bolts (24) and Flat washers (4).
4. Fix the L/R pedal (23L/R) onto the L/R pedal tube(22L/R) with 4pcs Hexagon socket bolts
(40). For easy assembly, while do this you can fold the Pedal tube(22L/R) upward.
www.powermaxfitness.net
10
Step 5.
1. Expand the Front handlebar (2) slightly then slide it onto the Central upright (9). Align their
holes and tighten them with 2 sets Hexagon socket head bolts (5), Arc washers (6) and
Nylon nuts (10)
2. Connect the sensor wires upper (16) and Grip pulse wire1(13) with the wires from the
Monitor (1) respectively.
3. Unscrew the two Cross head screws (7) and Flat washers (8) from the Monitor (1) and then
slide it onto the plate of the Central upright (9). Align their holes and screw them together.
www.powermaxfitness.net
11
Step 6.
1. For easy assembly, unscrewing the adjustment knob of the Adjustment tube (32) 2 or 3
circles and pulling it out, push the Main frame (35) to the folded position.
2. Fix the Body twister set (31) to the Central upright (9) with 1 pcs Hexagon socket head
bolt (30), Nylon nut (10), flat washer (18). Then insert the pull pin (29).
3. Install the Push-up bar (38) to the Main frame (35) with 4pcs Hexagon socket head bolts
(39), Flat washers (18). Now you can fasten all the screws, bolts and nuts of every
assembly step securely.
www.powermaxfitness.net
12
STORAGE AND MAINTENANCE
1. STORAGE: For saving the space, you can fold the treadmill. Unscrew the adjustment knob of
the Adjustment tube (32) 2 or 3 circles. Pulling it out and holding, push the Main frame (35) to
the folded position at the same time. Please refer below picture
2. CLEANING: After used some time, the treadmill maybe become dirty. Remove dust or dirty on
the treadmill with a damp cloth slightly. Periodical cleaning will help to prolong the product life.
Never use solvents on the deck or belt. To use solvents can reduce the life of the deck and belt.
3. BELT CENTERING ADJUSTMENT: When you run or walk, you may push off harder with one
foot than the other. This will cause the running belt to run off-centered. Occasionally the belt may
need further adjustment to keep it centered. To center the belt, use the enclosed Allen wrench
(#42) to adjust the rear roller position. (refer below picture)
If the belt is too far to the left side:
A: Turn the right roller bolt 1/4 turn clockwise (tighten)
B: Turn the left roller bolt 1/4 turn counter-clockwise (loosen)
If the belt is too far to the right side:
A: Turn the left roller bolt 1/4 turn clockwise (tighten)
B: Turn the right roller bolt 1/4 turn counter-clockwise (loosen)
www.powermaxfitness.net
13
4. RUNNING BELT TENSION ADJUSTMENT: When you place your foot on the belt, if you can
feel a slipping sensation, then the belt has stretched and is slipping across the rollers. This is a
normal and common adjustment on any treadmill. To eliminate this slipping, turn both Allen bolts
on the rear roller 1/4 turn as below shown. Try the treadmill again to check for slipping. Repeat if
necessary, but never turn the roller bolts more than 1/4 turn at a time.
5. LUBRICATING THE DECK: A well lubricated deck will ensure high performance of your treadmill
and reduce the level of normal wear and tear to important components. This treadmill has been
pre-lubricated at the factory. However, for optimal performance, the running deck may require
periodic lubrication. With average usage (30 minutes workout session 3 times a week), lubricate
with silicon every four to six months. You may adjust the timing of the lubrication based on the
intensity of the treadmill usage level. Please refer below the picture.
BELT TENSION ADJUSTMENT
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
PowerMax MFT-410 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
LifeGear 40160 Owner's manual
-
-
-
-
-
-
-
Exerpeutic Treadmill with Pulse Owner's manual
-
-