BEA 10ECA User manual

Type
User manual

BEA 10ECA is a ceiling accessory designed for use with BEA EAGLE sensors. It provides a mounting solution for the sensor in ceiling-mounted applications. The 10ECA features a pass-through for the EAGLE sensor harness, allowing for easy wiring and installation. It is suitable for use in both indoor and outdoor environments, making it a versatile accessory for various applications.

BEA 10ECA is a ceiling accessory designed for use with BEA EAGLE sensors. It provides a mounting solution for the sensor in ceiling-mounted applications. The 10ECA features a pass-through for the EAGLE sensor harness, allowing for easy wiring and installation. It is suitable for use in both indoor and outdoor environments, making it a versatile accessory for various applications.

©BEA | Original Instructions
75.5981.04 EAGLE FAMILY ACCESSORIES 20230408 Page 1 of 2
EAGLE FAMILY ACCESSORIES
SPACER
10EAGLESPACER
EAGLE SPACER V
10EAGLESPACERV
RAIN ACCESSORY
10ERA
CEILING ACCESSORY
10ECA
MOUNTING BRACKET
10EMB
RAIN COVER
10ERC
Reference EAGLE FAMILY User’s Guide (75.5957) for full EAGLE installation and setup.
ENGLISH
Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
PRECAUTIONS
Visit website for available
languages of this document.
!
CAUTION
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/
device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local,
national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines
(where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label
(e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
©BEA | Original Instructions
75.5981.04 EAGLE FAMILY ACCESSORIES 20230408 Page 2 of 2
INSTALLATION
FRONT
EAGLE mounting
holes
EAGLE
mounting holes
Header mounting
holes
EAGLE & wall
mounting holes
EAGLE & wall
mounting holes
EAGLE Harness
passage holes
EAGLE Harness
passage hole
EAGLE Harness
passage hole Camera
(EAGLE SPACER V only)
1. Pre-drill the EAGLE Harness passage hole
(14” for SPACER, 12” for SPACER V).
2. Route the EAGLE Harness through the wall/header and
then through the designated pass-thru on the spacer.
3. Route the EAGLE SPACER V camera harness through the
wall/header and then plug into SPACER V connector.
4. Mount the spacer to wall/header using self-drilling screws.
5. Route the EAGLE Harness through the pass-thru on the
sensor.
6. Mount sensor to accessory.
7. Wire the EAGLE Harness to the sensor.
EAGLE Harness
passage hole
SPACER / SPACER V
10EAGLESPACER / 10EAGLESPACERV
RAIN ACCESSORY
10ERA
CEILING ACCESSORY
10ECA
MOUNTING BRACKET
10EMB
RAIN COVER
10ERC
BOTTOM
Wall mounting
holes
Tech Support & Customer Service: 1-800-523-2462 | General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com
PLEASE KEEP FOR FURTHER USE – DESIGNED FOR COLOR PRINTING
CAMERA TECHNICAL SPECIFICATIONS
Voltage regulator
(built into wire harness):
6.6 – 36 VDC (±10%)
6 – 28 VAC (±10%)
Operating temperature: -30 – 60 °C (max. RH: 95%)
Video output: 1.0 (Vp-p) / 75Ω
Image Sensor: CMOS
Horizontal resolution: 480 TVL
NTSC output: 720 (H) × 480 (V)
Sync system: Inter-Sync
Frame rate: 30 fps
Min. illumination: 0.01 LUX
AE control: auto
Gain control: auto
Elec. shutter: 1 s ~ 1/10,000 s
S/N ratio: > 50 dB
AWB: auto
Voltage
Regulator
  • Page 1 1
  • Page 2 2

BEA 10ECA User manual

Type
User manual

BEA 10ECA is a ceiling accessory designed for use with BEA EAGLE sensors. It provides a mounting solution for the sensor in ceiling-mounted applications. The 10ECA features a pass-through for the EAGLE sensor harness, allowing for easy wiring and installation. It is suitable for use in both indoor and outdoor environments, making it a versatile accessory for various applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI