2. Roland
  3. JU-06

Roland JU-06 User manual

  • Hello! I am an AI chatbot trained to assist you with the Roland JU-06 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I connect the JU-06 to my computer to control the JUNO-106 software synthesizer?
    What is the MIDI input device that I should choose in my DAW software?
    What happens if I select control mode in the JU-06?
    How do I return to normal mode from control mode in the JU-06?
    Which JU-06 controllers correspond to the DCO RANGE 2' parameter in the JUNO-106 software synthesizer?
    Which JU-06 controller corresponds to the VCF CUTOFF FREQ parameter in the JUNO-106 software synthesizer?
1
JU-06 Version 1.20 Supplementary Manual
This document explains the functions that have been added to the JU-06. Read it in conjunction with the owner’s manual.
Controlling the JUNO-106 Software Synthesizer
You can use the controllers of the JU-06 to control the JUNO-106 software synthesizer inside your DAW software.
MEMO
For details on the JUNO-106 software synthesizer, refer to Roland Cloud (https://www.rolandcloud.com/).
1. Using a USB cable, connect the JU-06 to your computer.
2. While holding down the PATCH NUMBER [8] button, turn on the power.
You’ll need to install a USB driver on the computer. For details, refer to the JU-06 owner’s manual.
The JU-06 is in software synthesizer control mode, and the display indicates “
Ct
”.
3. As the MIDI input device in the DAW software you’re using, choose “Boutique.”
For more about the settings of your DAW software, refer to your DAW’s help or owner’s manual.
* If you select control mode, the internal sound engine does not play.
* If you select control mode, the following settings change.
5 MIDI CH: 1 ch
5 Control change output mode: Output to both USB and MIDI.
MEMO
To return to normal mode, turn the power o and on again.
Copyright © 2017 ROLAND CORPORATION01
2
JU-06 Version 1.20 Supplementary Manual
JU-06 Control Mode Correspondence Table
JUNO-106 software synthesizer
1 2 3 4
5 6
7 8
JU-06
1 2 3 4 5 6
7 8
3
JU-06 Version 1.20 Supplementary Manual
No.
JUNO-106
software synthesizer
JU-06 Remarks
1
LFO RATE LFO RATE
LFO DELAY TIME LFO DELAY TIME
LFO KEY TRIG – Cannot be controlled.
LFO TRIG ENV – Cannot be controlled.
2
DCO RANGE 2’ – Cannot be controlled.
DCO RANGE 4’ DCO RANGE 4’ CC VALU: 101
DCO RANGE 8’ DCO RANGE 8’ CC VALUE: 76
DCO RANGE 16’ DCO RANGE 16’ CC VALUE: 50
DCO RANGE 32’ – Cannot be controlled.
DCO RANGE 64’ – Cannot be controlled.
DCO LFO MOD DCO LFO MOD -128–127
DCO PWM LEVEL DCO PWM LEVEL
DCO PWM SRC DCO PWM SRC MAN.LFO only
DCO PWM LEVEL DCO PWM 0 and 127 only
DCO SAW LEVEL DCO SAW 0 and 127 only
DCO SUB OSC LEVEL DCO SUB OSC LEVEL
DCO NOISE LEVEL DCO NOISE LEVEL
3
HPF FREQ HPF FREQ
4
VCF VELOCITY SENS – Cannot be controlled.
VCF CUTOFF FREQ VCF CUTOFF FREQ
VCF RES VCF RES
VCF ENV POLARITY No corresponding controller.
VCF ENV1 MOD VCF ENV MOD -128–127
VCF LFO MOD VCF LFO MOD -128–127
VCF KEYFOLLOW VCF KEYFOLLOW -128–127
5
VCA VELOCITY SENS – Cannot be controlled.
VCA TONE – Cannot be controlled.
VCA ENV MODE VCA ENV MODE GATE and ENV1 only
VCA LEVEL VCA LEVEL
6
ENV1 ATTACK ENV ATTACK
ENV1 DECAY ENV DECAY
ENV1 SUSTAIN ENV SUSTAIN
ENV1 RELEASE ENV RELEASE
ENV2 ATTACK – Cannot be controlled.
ENV2 DECAY – Cannot be controlled.
ENV2 SUSTAIN – Cannot be controlled.
ENV2 RELEASE – Cannot be controlled.
7
CHORUS OFF – Operate using the CHORUS I/II button.
8
CHORUS I CHORUS I
CHORUS II CHORUS II
/