Grizzly W1704 Owner's manual

Category
Lathes
Type
Owner's manual
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 01/20)
MODEL W1704
8" X 13" BENCHTOP
WOOD LATHE
Phone: (360) 734-3482 • Online Technical Support: [email protected]
    COPYRIGHT © DECEMBER, 2003 BY WOODSTOCK INTERNATIONAL, INC. REVISED JANUARY, 2020 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#5378TR  Printed in China
4000909
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
SET UPELECTRICAL MAINTENANCE
SERVICE PARTS
OPERATIONS
SAFETYINTRODUCTION
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION .....................................2
Woodstock Technical Support
.................. 2
Machine Specifications
.......................... 3
Identification
..................................... 5
Controls & Components
......................... 6
SAFETY ...............................................7
Standard Machinery Safety Instructions
...... 7
Additional Safety for Wood Lathes
............ 9
Glossary of Terms
.............................. 10
ELECTRICAL ....................................... 11
Circuit Requirements
.......................... 11
Grounding Requirements
...................... 12
Extension Cords
................................ 12
SETUP .............................................. 13
Unpacking
....................................... 13
Items Needed for Setup
....................... 13
Inventory
........................................ 14
Hardware Recognition Chart
................. 15
Cleaning Machine
............................... 16
Machine Placement
............................ 16
Assembly
......................................... 17
Test Run
.......................................... 18
OPERATIONS....................................... 19
General
.......................................... 19
Workpiece Inspection
.......................... 20
Selecting Turning Tools
........................ 21
Adjusting Tailstock
............................. 22
Adjusting Tool Rest
............................. 23
Installing/Removing Headstock Center
..... 24
Installing/Removing Tailstock Center
....... 25
Installing/Removing Faceplate
............... 26
Changing Spindle Speed
....................... 27
Spindle Turning
................................. 28
Faceplate Turning
.............................. 30
Sanding/Finishing
.............................. 31
ACCESSORIES ...................................... 32
Wood Lathe Accessories
....................... 32
MAINTENANCE .................................... 34
General
.......................................... 34
Cleaning & Protecting
......................... 34
Lubrication
...................................... 34
SERVICE ............................................ 35
General
.......................................... 35
Aligning Pulleys
................................. 35
Changing/Tensioning Belt
..................... 36
Replacing Fuse
.................................. 37
Replacing Brushes
.............................. 37
Troubleshooting
................................. 38
Electrical Safety Instructions
................. 40
Electrical Components
........................ 41
Wiring Diagram
................................. 42
PARTS .............................................. 43
Main
.............................................. 43
WARRANTY ........................................ 45
Contents
-2-
Model W1704 (For Machines Mfd. Since 01/20)
INTRODUCTI ON
Woodstock Technical Support
INTRODUCTION
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety
precautions are overlooked or ignored,
serious personal injury may occur.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious
personal injury, damage to equipment, or
poor work results.
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 Ext. 2 or send e-mail to: techsupport@
woodstockint.com. Our knowledgeable staff will help you troubleshoot problems and process warranty
claims.
-3-
Model W1704 (For Machines Mfd. Since 01/20)
INTRODUCTI ON
Model W1704 Machine Specifications, Page 1 of 2
MODEL W1704
8" X 13" BENCHTOP WOOD LATHE
Product Dimensions
Weight........................................................................................................... 41 lbs.
Width (side‐to‐side) x Depth (front‐to‐back) x Height................................... 29 x 10‐1/2 x 13 in.
Footprint (Length x Width)..................................................................... 23‐1/2 x 5‐1/2 in.
Shipping Dimensions
Type.................................................................................................... Cardboard Box
Content........................................................................................................ Machine
Weight........................................................................................................... 52 lbs.
Length x Width x Height............................................................................. 30 x 15 x 8 in.
Electrical
Power Requirement.................................................................... 120V, Single‐Phase, 60 Hz
Full‐Load Current Rating........................................................................................ 3.2A
Minimum Circuit Size............................................................................................. 15A
Connection Type......................................................................................... Cord & Plug
Power Cord Included.............................................................................................. Yes
Power Cord Length............................................................................................... 6 ft.
Power Cord Gauge............................................................................................ 18 AWG
Plug Included....................................................................................................... Yes
Included Plug Type............................................................................................... 5‐15
Switch Type............................................................ Paddle Safety Switch w/Removable Key
Motors
Main
Horsepower.............................................................................................. 1/3 HP
Phase.............................................................................................. Single‐Phase
Amps........................................................................................................... 4A
Speed.................................................................................................. 4600 RPM
Type.................................................................................................... Universal
Power Transfer ............................................................................................ Belt
Bearings............................................................... Shielded & Permanently Lubricated
Main Specifications
Operation Information
Swing Over Bed............................................................................................ 8 in.
Distance Between Centers.............................................................................. 13 in.
Max. Distance Tool Rest to Spindle Center....................................................... 2‐3/4 in.
No of Spindle Speeds................................................................................. Variable
Spindle Speed Range......................................................................... 750 – 3200 RPM
Floor to Center Height.............................................................................. 9‐3/4 in.
-4-
Model W1704 (For Machines Mfd. Since 01/20)
INTRODUCTI ON
Model W1704 Machine Specifications, Page 2 of 2
Spindle Information
Spindle Taper.............................................................................................. MT#1
Spindle Thread Size............................................................................. 3/4" x 16 TPI
Spindle Thread Direction......................................................................... Right Hand
Spindle Bore........................................................................................... 0.394 in.
Type of Included Spindle Center........................................................................ Spur
Tailstock Information
Tailstock Taper........................................................................................... MT#1
Type of Included Tailstock Center...................................................................... Live
Construction
Bed................................................................................ Precision‐Ground Cast Iron
Frame........................................................................................ Cast Iron & Steel
Headstock.................................................................................... Cast Iron & Steel
Tailstock..................................................................................... Cast Iron & Steel
Paint Type/Finish...................................................................................... Enamel
Other Related Information
Bed Width............................................................................................. 5‐1/8 in.
Faceplate Size........................................................................................ 5‐3/4 in.
Other
Country of Origin ............................................................................................... China
Warranty ....................................................................................................... 2 Years
Approximate Assembly & Setup Time ................................................................. 15 Minutes
Serial Number Location .................................................................... ID Label on Lathe Bed
ISO 9001 Factory .................................................................................................. Yes
Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................... Yes
-5-
Model W1704 (For Machines Mfd. Since 01/20)
INTRODUCTI ON
Identification
Become familiar with the names and locations of the controls and features shown below to better
understand the instructions in this manual.
For Your Own Safety Read Instruction Manual Before
Operating Lathe
a) Wear eye protection.
b) Do not wear gloves, necktie, or loose clothing.
c) Tighten all locks before operating.
d) Rotate workpiece by hand before applying power.
e) Rough out workpiece before installing on faceplate.
f) Do not mount split workpiece or one containing knot.
g) Use lowest speed when starting new workpiece.
Quill
Bed
Tool Rest
MotorON/OFF
Switch
Headstock Spindle Tailstock
Adjustment Knob
Spindle
Speed Dial
Tool Rest
Base
Tool Rest Base
Lock Lever
Tool Rest
Lock Handle
Tailstock
Lock Lever
Quill
Lock Handle
-6-
Model W1704 (For Machines Mfd. Since 01/20)
INTRODUCTI ON
Controls & Components
Refer to Figures 13 and the following descriptions to
become familiar with the basic controls and components
of this machine. Understanding these items and how they
work will help you understand the rest of the manual and
stay safe when operating this machine.
To reduce your risk of serious injury
or damage to the machine, read this
entire manual BEFORE using machine.
A. Spindle Speed Dial: Controls spindle speed. Always
turn dial to lowest setting before starting lathe.
B. ON/OFF Paddle Switch: Turns lathe ON and OFF.
C. Tailstock Adjustment Knob: Moves quill toward or
away from spindle.
D. Quill Lock Handle: Secures quill in position.
E
. Quill: Holds centers or tooling. Can be moved toward
and away from spindle.
F. Tailstock Lock Lever: Secures tailstock in position
along bed.
G. Tool Rest: Provides stable platform for cutting tools.
H. Tool Rest Lock Handle: Secures tool rest in position.
I. Tool Rest Base (Banjo) Lock Lever: Secures tool
rest holder when tool rest is proper distance from
workpiece.
Figure 1. Switch box controls.
A
B
Figure 2. Tailstock controls.
D
F
C
E
Figure 3. Tool rest controls.
I
H
G
-7-
Model W1704 (For Machines Mfd. Since 01/20)
SAFETY
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the equipment or a situation that may cause
damage to the machinery.
NOTICE
SAFETY
OWNER’S MANUAL.
Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY.
Untrained operators
have a higher risk of being hurt or killed. Only
allow trained/supervised people to use this
machine. When machine is not being used,
disconnect power, remove switch keys, or
lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
DANGEROUS ENVIRONMENTS.
Do not use
machinery in areas that are wet, cluttered,
or have poor lighting. Operating machinery
in these areas greatly increases the risk of
accidents and injury.
MENTAL ALERTNESS REQUIRED.
Full mental
alertness is required for safe operation of
machinery. Never operate under the influence
of drugs or alcohol, when tired, or when
distracted.
ELECTRICAL EQUIPMENT INJURY RISKS. You can
be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow an
electrician or qualified service personnel to
do electrical installation or repair work, and
always disconnect power before accessing or
exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect
machine from power supply BEFORE making
adjustments, changing tooling, or servicing
machine. This eliminates the risk of injury
from unintended startup or contact with live
electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
Standard Machinery Safety Instructions
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention mea-
sures—this responsibility is ultimately up to the operator!
SAFETY
Standard Machinery Safety Instructions
-8-
Model W1704 (For Machines Mfd. Since 01/20)
SAFETY
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips, which could cause loss
of workpiece control.
HAZARDOUS
DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware of
dust hazards associated with each workpiece
material, and always wear a NIOSH-approved
respirator to reduce your risk.
HEARING PROTECTION.
Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
REMOVE ADJUSTING TOOLS.
Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys,
wrenches, or any other tools on machine.
Always verify removal before starting!
INTENDED USAGE.
Only use machine for its
intended purposenever make modifications
without prior approval from Woodstock
International. Modifying machine or using
it differently than intended will void the
warranty and may result in malfunction or
mechanical failure that leads to serious
personal injury or death!
AWKWARD POSITIONS.
Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
CHILDREN & BYSTANDERS.
Keep children and
bystanders at a safe distance from the work
area. Stop using machine if they become a
distraction.
GUARDS & COVERS.
Guards and covers reduce
accidental contact with moving parts or flying
debris—make sure they are properly installed,
undamaged, and working correctly.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury may
occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during
operation greatly increases risk of injury or
loss of control. Before starting, verify machine
is stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase risk of serious injury.
UNATTENDED OPERATION. To reduce the risk
of accidental injury, turn machine OFF and
ensure all moving parts completely stop
before walking away. Never leave machine
running while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. A
machine that is improperly maintained could
malfunction, leading to serious personal injury
or death.
CHECK DAMAGED PARTS. Regularly inspect
machine for any condition that may affect
safe operation. Immediately repair or replace
damaged or mis-adjusted parts before
operating machine.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside, resulting
in a short. Do not handle cord/plug with wet
hands. Avoid cord damage by keeping it away
from heated surfaces, high traffic areas, harsh
chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the
intended operation, stop using the machine!
Contact Technical Support at (360) 734-3482.
-9-
Model W1704 (For Machines Mfd. Since 01/20)
SAFETY
Additional Safety for Wood Lathes
INTEGRITY OF STOCK.
Verify each workpiece is
free of knots, splits, nails, or foreign material
to ensure it can safely rotate on spindle
without breaking apart or causing turning tool
kickback.
WORKPIECE PREPARATION.
Before mounting, cut
off waste portions with a bandsaw or other
tool to ensure workpiece has no large edges to
catch turning tool, and it will rotate without
dangerous wobbling.
SECURING LOCKS.
Verify tool rest, headstock,
and tailstock are secure before turning lathe
ON.
SECURING WORKPIECE.
An improperly secured
workpiece can fly off spindle with deadly
force. Use proven setup techniques and always
verify workpiece is well-secured before starting
lathe. Only use high-quality fasteners with non-
tapered heads for faceplate attachment.
TOOL SUPPORT.
An improperly supported tool
may be grabbed or ejected. Adjust tool rest
approximately
1
4 away from workpiece and
1
8 above workpiece center line to provide
proper support for turning tool. Firmly hold
turning tool with both hands against tool rest.
TOOL KICKBACK
. Occurs when turning tool is
ejected from workpiece with great force,
striking operator or bystanders. Commonly
caused by poor workpiece selection/
preparation, improper tool usage, or improper
machine setup or tool rest adjustment.
ADJUSTMENT TOOLS
. Remove all chuck keys,
wrenches, and adjustment tools before turning
lathe ON. A tool left on the lathe can become
a deadly projectile when spindle is started.
SAFE CLEARANCES
. Before starting spindle, verify
workpiece has adequate clearance by hand-
rotating it through its entire range of motion.
EYE/FACE PROTECTION. Always wear a face
shield and safety glasses when operating lathe.
PROPER APPAREL.
Do not wear gloves, necktie or
loose clothing. Keep keep long hair away from
rotating spindle.
SPEED RATES. Select correct spindle speed for
workpiece size, type, shape, and condition.
Use low speeds when roughing or when turning
large, long, or non-concentric workpieces.
Allow spindle to reach full speed before
turning.
NEW SETUPS. Test each new setup by starting
spindle rotation at the lowest speed and
standing to the side of the lathe until
workpiece reaches full speed and you can
verify safe rotation.
ROUGHING.
Use correct tool. Take light cuts, use
low speeds, and firmly support tool with both
hands.
SHARP TOOLS. Only use sharp turning tools
they cut with less resistance than dull tools.
Dull turning tools can catch or grab and pull
your hands into the rotating workpiece.
STOPPING SPINDLE. Always allow spindle to
completely
stop on its own. Never put hands or
another object on spinning workpiece.
ADJUSTMENTS/MAINTENANCE. Make sure wood
lathe is turned OFF
, disconnected from power,
and all moving parts are completely stopped
before doing adjustments or maintenance.
MEASURING WORKPIECE. Only measure
workpiece after it has stopped. Trying to
measure a spinning workpiece increases
entanglement risk.
SANDING/POLISHING. To reduce entanglement
risk, remove tool rest before sanding. Never
completely wrap sandpaper around workpiece.
MAIN INJURY HAZARDS: Death or crushing injury from getting entangled in rotating spindle or
workpiece; death, blindness, or broken bones from being struck by a workpiece that breaks
apart or comes loose during rotation, turning tool kickback, or flying wood chips. To minimize
your risk of these hazards, always heed the following warning information:
-10-
Model W1704 (For Machines Mfd. Since 01/20)
SAFETY
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this wood lathe and woodworking in general. Become familiar with these terms for assembling, adjust-
ing or operating this machine.
Glossary of Terms
Bed: The long, rail-like metal base to which the
tailstock, tool base, and headstock are attached.
Chuck: A mechanical device that attaches to the
spindle and holds the workpiece.
Faceplate: The metal disc that threads onto the
headstock spindle.
Faceplate Turning: Turning situation in which the
grain of the turning stock is at right angles to the
lathe bed axis.
Backing Block: A sacrificial piece of wood glued
to the base of the workpiece and screwed to the
faceplate. Often used to prevent mounting marks
from appearing on the completed workpiece.
Headstock: The cast metal box to which the
motor is attached and contains the spindle, bear-
ings, belts, and electrical components for operat-
ing the lathe.
Offset Turning: A turning situation where the
center of the workpiece is offset at various
stages of the work to produce different shapes.
Outboard Turning: Turning of workpiece with
the headstock situated at the far end of the lathe
so the work done is not over the bed of the lathe.
Roughing Out: Taking stock from square billet to
round blank.
Spindle: This term has two meanings. First, it
refers to the threaded shaft in the headstock to
which the faceplate is attached. Second, it refers
to any work that is spindle-turned.
Spindle-Turning: Work performed where the
grain and length of the workpiece are parallel to
the axis of the bed.
Swing: The capacity of the lathe, measured by
doubling the distance from the bed to the spindle
center.
Tailstock: The metal component at the opposite
end of the bed from the headstock containing a
quill and live or dead centers. It maintains pres-
sure on the spindle-turned workpiece.
Tool Base: The movable metal fixture attached
to the bed upon which the tool rest is fixed.
Tool Rest: The adjustable metal arm upon which
the tool rests during a turning operation.
Way: One of the metal rails that make up the bed
of the lathe.
-11-
Model W1704 (For Machines Mfd. Since 01/20)
ELECTRICAL
ELECTRICAL
Circuit Requirements
This machine must be connected to the correct size and
type of power supply circuit, or fire or electrical damage
may occur. Read through this section to determine if an
adequate power supply circuit is available. If a correct
circuit is not available, a qualified electrician MUST install
one before you can connect the machine to power.
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the full-
load current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
Circuit Requirements
This machine is prewired to operate on a power supply
circuit that has a verified ground and meets the following
requirements:
Circuit Type .............. 110V/120V, 60 Hz, Single-Phase
Circuit Size ............................................ 15 Amps
Plug/Receptacle ................................... NEMA 5-15
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Full-Load Current Rating at 120V ............... 3.2 Amps
The machine must be properly set up
before it is safe to operate. DO NOT
connect this machine to the power
source until instrtucted to do so later
in this manual.
Incorrectly wiring or grounding this
machine can cause electrocution, fire,
or machine damage. To reduce this risk,
only an electrician or qualified service
personnel should do any required
electrical work on this machine.
NOTICE
The circuit requirements listed in this
manual apply to a dedicated circuit
where only one machine will be running
at a time. If this machine will be
connected to a shared circuit where
multiple machines will be running at the
same time, consult with an electrician
to ensure that the circuit is properly
sized for safe operation.
-12-
Model W1704 (For Machines Mfd. Since 01/20)
ELECTRICAL
Grounding Requirements
This machine MUST be grounded. In the event of certain
types of
malfunctions or breakdowns, grounding provides
a path of least resistance for electric current
to travelin
order
to reduce the risk of electric shock.
Improper connection of the equipment-grounding
wire
will
increase
the risk of electric shock. The wire with green
insulation
(with/without yellow stripes) is the equipment-
grounding
wire. If repair or replacement of the power
cord or plug is necessary, do not connect the equipment-
grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel
if
you do not understand these grounding requirements,
or if
you are in doubt about whether the tool is
properly grounded.
If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
For 120V Connection
Extension Cords
We do not recommend using an extension cord with
this machine. Extension cords cause voltage drop, which
may damage electrical components and shorten motor
life. Voltage drop increases with longer extension cords
and smaller gauge sizes (higher gauge numbers indicate
smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required
plug and receptacle, and
meet the following requirements:
Minimum Gauge Size at 120V ...................... 16 AWG
Maximum Length (Shorter is Better) ................50 ft.
Grounding Pin
Neutral Hot
5-15 PLUG
GROUNDED
5-15 RECEPTACLE
120V
Figure 4. NEMA 5-15 plug & receptacle.
DO NOT modify the provided plug or
use an adapter if the plug will not
fit the receptacle. Instead, have an
electrician install the proper receptacle
on a power supply circuit that meets
the requirements for this machine.
This machine is equipped with a power cord with an
equipment-grounding
wire and NE MA 5-15 grounding
plug
(see figure). The plug must only be inserted into
a matching
receptacle that is properly installed and
grounded in accordance with local codes and ordinances.
-13-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
USE helpers or power
lifting equipment to lift
this machine. Otherwise,
serious personal injury
may occur.
Wear safety glasses during
entire setup process!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual
to become familiar with
the controls and opera-
tions before starting the
machine!
Items Needed for Setup
The following items are needed, but not included, to set
up your machine.
Description Qty
Safety Glasses (for each person) ........................1
• Solvent/Cleaner ...........................................1
• Gloves ................................................. 1 Pair
Shop Rags ....................................... As Needed
Additional Person ..........................................1
Phillips Head Screwdriver #2 ............................1
Quality Metal Protectant Lubricant......... As Needed
-14-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
Inventory
The following is a list of items shipped with your machine.
Before beginning setup, lay these items out and inventory
them.
Note:
If you cannot find an item on this list, carefully
check around/inside the machine and packaging materials.
Often, these items get lost in packaging materials while
unpacking or they are pre-installed at the factory.
Inventory (Figures 5–6) Qty
A. Lathe Assembly
—Tool Rest Base (mounted) ..............................1
—Tailstock (mounted)
.....................................1
B.
Faceplate 5
3
4" .............................................1
C. Tool Rest 7" .................................................1
D
. Tool Rest 4
1
2" ..............................................1
E.
Adjustable Levers (Tool Rest Base, Tailstock) .........2
F
. Lock Handle M6-1 x 28 (Tool Rest) ......................1
G.
Live Center .................................................1
H.
Spur Center .................................................1
I
. Knockout Tool ..............................................1
J
. Lock Handle M6-1 x 17 (Quill) ...........................1
K.
Hardware (Not Shown)
—Hex Wrenches 3, 5mm .............................. 1 Ea
—Open-Ends Wrench 19/27mm
..........................1
A
Figure 5. Lathe assembly.
Figure 6. Loose inventory.
C
D
E
F
H
G
B
I
J
-15-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
Hex
Wrench
16mm
MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE
7
16"
3
8"
1
4"
5
16"
#10
1
2"
WASHERS ARE MEASURED BY THE INSIDE DIAMETER
USE THIS CHART TO IDENTIFY
HARDWARE DURING THE
INVENTORY/ASSEMBLY
PROCESS.
Flat Washer
Lock
Washer
Hex
Nut
Wing
Nut
Set
Screw
Cap
Screw
Carriage
Bolt
Hex
Bolt
Button
Head
Screw
Flange
Bolt
LINES ARE
1
16" INCH APART
1
4"
3
8"
1
2"
5
8"
5
16"
7
16"
9
16"
3
4"
7
8"
3
2
1
4"
2
1
2"
2
3
4"
2
1
3
4"
1
1
2"
1
1
4"
1
LINES ARE 1MM APART
5mm
10mm
20mm
15mm
25mm
40mm
30mm
35mm
45mm
50mm
60mm
55mm
70mm
65mm
75mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5
8"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
9
16"
1
2"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
12mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
10mm
7
16"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
8mm
3
8"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5
16"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
1
4"
W
A
S
H
E
R
D
I
A
M
E
T
E
R
#10
W
A
S
H
E
R
D
I
A
M
E
T
E
R
W
A
S
H
E
R
D
I
A
M
E
T
E
R
4mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
6mm
W
A
S
H
E
R
D
I
A
M
E
T
E
R
5mm
4mm
6mm
5mm
8mm
10mm
12mm
Tap
Screw
Phillips
Head
Screw
Flat
Head
Screw
E-Clip
External
Retaining
Ring
Internal
Retaining
Ring
Key
Lock
Nut
Hardware Recognition Chart
-16-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
Cleaning Machine Machine Placement
Workbench Load
Refer to the Machine Specifications for the
weight and footprint specifications of your
machine. Some workbenches may require
additional reinforcement to support the weight
of the machine and workpiece materials.
Consider anticipated workpiece sizes and
additional space needed for auxiliary stands,
work tables, or other machinery when
establishing a location for this machine in the
shop. Below is the minimum amount of space
needed for the machine.
Placement Location
INJURY HAZARD! Untrained
users can injure themselves
with this machine. Restrict
access to machine when
you are away, especially if
it is installed where chil-
dren are present.
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but
it will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper
care of your machine's unpainted surfaces.
There are many ways to remove this rust
preventative, but the following steps work well
in a wide variety of situations. Always follow the
manufacturer’s instructions with any cleaning
product you use and make sure you work in a
well-ventilated area to minimize exposure to
toxic fumes.
Before cleaning, gather the following:
Disposable rags
Cleaner/degreaser (WD•40 works well)
Safety glasses & disposable gloves
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it
soak for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/
degreaser is effective, the rust
preventative will wipe off easily. If you
have a plastic paint scraper, scrape off as
much as you can first, then wipe off the
rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a
quality metal protectant to prevent rust.
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
36"
11
1
/
2
"
Figure 7. Minimum working clearances.
-17-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
Assembly
Before beginning the assembly process, refer to Items
Needed for Setup
and gather everything you need.
Ensure all parts have been properly cleaned of any
heavy-duty rust-preventative applied at the factory (if
applicable). Be sure to complete all steps in the assembly
procedure prior to performing the
Test Run
or connecting
the machine to power.
To assemble machine, do these steps:
1. Install tailstock lock lever and M6-1 x 17 quill lock
handle, as shown in Figure 8.
2
. Install tool rest base lock lever and M6-1 x 28 tool
rest lock handle, as shown in
Figure 9.
3
. Insert tool rest into tool rest base and tighten tool
rest lock handle (see Figure 10).
Note: Unless workpiece clearance is an issue, always
install the larger of the (2) tool rests included with
this machine to give yourself more room to work.
lock levers
Figure 8. Hardware installed on tailstock.
Quill
Lock Handle
Tailstock
Lock Lever
Figure 9. Hardware installed on tool rest
base.
Tool Rest
Lock Handle
Tool Rest Base
Lock Lever
Figure 10. Tool rest installed on tool rest
base.
Tool
Rest
Tool Rest
Lock Handle
Tool Rest Base
Lock Lever
-18-
Model W1704 (For Machines Mfd. Since 01/20)
SETUP
Test Run
Serious injury or death can result
from using this machine BEFORE
understanding its controls and related
safety information. DO NOT operate, or
allow others to operate, machine until
the information is understood.
DO NOT start machine until all
preceding setup instructions have been
performed. Operating an improperly set
up machine may result in malfunction
or unexpected results that can lead
to serious injury, death, or machine/
property damage.
Once assembly is complete, test run the machine to
ensure it is properly connected to power and safety
components are functioning properly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from power,
and fix the problem BEFORE operating the machine again.
The
Troubleshooting table in the SERVICE
section of this
manual can help.
To test run machine, do these steps:
1. Clear all setup tools away from machine.
2. Turn spindle speed dial all the way counterclockwise
(see Figure 11).
3.
Connect machine to power supply.
4. Verify machine is operating correctly by flipping ON/
OFF paddle switch up, then slowly turning spindle
speed dial clockwise.
When operating correctly, machine runs smoothly
with little or no vibration or rubbing noises.
Investigate and correct strange or unusual noises
or vibrations before operating machine further.
Always disconnect machine from power when
investigating or correcting potential problems.
5.
Turn spindle speed dial all the way counterclockwise.
6. Turn machine OFF.
7.
Remove switch disabling key (see Figure 12).
8.
Try to start machine with paddle switch.
— If machine does not start, switch disabling feature
is working correctly.
— If machine does start, immediately disconnect
power to machine. Switch disabling feature is not
working correctly. Call Tech Support for help.
Congratulation! The Test Run is complete.
The test run consists of verifying the following: 1) The
motor powers up and runs correctly, and 2) the safety
disabling mechanism on the switch works correctly.
Figure 11. Location of spindle speed dial.
Figure 12. Removing switch key from
paddle switch.
Spindle
Speed Dial
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Grizzly W1704 Owner's manual

Category
Lathes
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI