Land Pride PFL12 Series User manual

Brand: Land Pride

Model: PFL12 Series

Type: User manual

This manual is also suitable for

PFL12

Table of Contents

Cover photo may show optional equipment not supplied

with standard unit.

For an Operator’s Manual and Decal Kit in French

Language, please see your Land Pride dealer.

Read the Operator’s Manual entirely. When you see this symbol,

the subsequent instructions and warnings are serious - follow

without exception. Your life and the lives of others depend on it!

Pallet Fork

PFL1242

319-211M

Operator’s Manual

Printed 4/17/19

72040

4/17/19PFL1242 Pallet Fork 319-211M

Machine Identification

Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new

manual.

If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were

originally ordered, the weights and measurements are no longer accurate for your machine. Update the record by

adding the machine weight and measurements provided in the Specifications & Capacities Section of this manual with

the Option(s) weight and measurements.

Dealer Contact Information

Model Number

Serial Number

Machine Height

Machine Length

Machine Width

Machine Weight

Delivery Date

First Operation

Accessories

Name:

Street:

City/State:

Telephone:

Email:

WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov

California Proposition 65

Table of Contents

4/17/19

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1

Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 8

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 1: Assembly & Set-Up . . . . . . . . . . . . 9

Fork Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Tractor Shutdown Procedure . . . . . . . . . . . . . . . . 10

Tractor Hook-Up . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Section 2: Adjustments . . . . . . . . . . . . . . . . . 11

Fork Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Section 3: Operating Procedures . . . . . . . . . 12

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 12

Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Transport Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pallet Fork Operation . . . . . . . . . . . . . . . . . . . . . . 13

Picking up a Load . . . . . . . . . . . . . . . . . . . . . . . 13

Traveling with a Load . . . . . . . . . . . . . . . . . . . . . 14

Placing a Load . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Unhooking the Pallet Fork . . . . . . . . . . . . . . . . . . . 14

General Operating Instructions . . . . . . . . . . . . . . . 15

Section 4: Maintenance & Lubrication . . . . . 16

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Long-Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 16

Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pallet Fork Contact Points . . . . . . . . . . . . . . . . . 17

Section 5: Specifications & Capacities . . . . 19

Section 6: Features & Benefits . . . . . . . . . . . 20

Section 7: Troubleshooting . . . . . . . . . . . . . . 21

Section 8: Torque Values Chart . . . . . . . . . . 22

Section 9: Warranty . . . . . . . . . . . . . . . . . . . . 23

Table of Contents Continued

4/17/19

Parts Manual QR Locator

The QR (Quick Reference) code on the

cover and to the left will take you to the

Parts Manual for this equipment.

Download the appropriate App on your

smart phone, open the App, point your

phone on the QR code and take a picture.

Dealer QR Locator

The QR code on the left will

link you to available dealers

for Land Pride products.

Refer to Parts Manual QR

Locator on this page for

detailed instructions.

Table of Contents

See previous page for Table of Contents.

Important Safety Information

4/17/19

Important Safety Information

Listed below are common practices that may or may not be applicable to the products

described in this manual.



Safety at All Times

Careful operation is your best

assurance against an accident.

All operators, no matter how much

experience they may have, should

carefully read this manual and

other related manuals, or have the

manuals read to them, before

operating the power machine and

this attachment.

 Thoroughly read and understand

the “Safety Label” section. Read

all instructions noted on them.

 Do not operate the equipment

while under the influence of drugs

or alcohol as they impair the ability

to safely and properly operate the

equipment.

 The operator should be familiar

with all functions of the tractor and

attachment and be able to handle

emergencies quickly.

 Make sure all guards and shields

appropriate for the operation are in

place and secured before

operating attachment.

 Keep all bystanders away from

equipment and work area.

 Start tractor from the driver’s seat

with hydraulic controls in neutral.

 Operate tractor and controls from

the driver’s seat only.

 Never dismount from a moving

tractor or leave tractor unattended

with engine running.

 Do not allow anyone to stand

between tractor and attachment

while hooking-up.

 Keep hands, feet, and clothing

away from power-driven parts.

 While transporting and operating

equipment, watch out for objects

overhead and along side such as

fences, trees, buildings, wires, etc.

 Store attachment in an area where

children normally do not play.

When needed, secure attachment

against falling with support blocks.

Look for the Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

potential hazard to personal safety involved and extra

safety precaution must be taken. When you see this

symbol, be alert and carefully read the message that

follows it. In addition to design and configuration of

equipment, hazard control, and accident prevention are

dependent upon the awareness, concern, prudence, and

proper training of personnel involved in the operation,

transport, maintenance, and storage of equipment.

Tractor Shutdown & Storage

 If engaged, disengage power

take-off.

 Park on solid, level ground and

lower attachment to ground or

onto support blocks.

 Put tractor in park or set park

brake, turn off engine, and remove

switch key to prevent unauthorized

starting.

 Relieve all hydraulic pressure to

auxiliary hydraulic lines.

 Wait for all components to stop

before leaving operator’s seat.

 Use steps, grab-handles and

anti-slip surfaces when stepping

on and off the tractor.

 Detach and store attachment in an

area where children normally do

not play. Secure attachment using

blocks and supports.

OFF

Safety Precautions for

Children

Tragedy can occur if the operator

is not alert to the presence of

children. Children generally are

attracted to attachments and their

work.

 Never assume children will remain

where you last saw them.

 Keep children out of the work area

and under the watchful eye of a

responsible adult.

 Be alert and shut the attachment

and tractor down if children enter

the work area.

 Never carry children on the tractor

or attachment. There is not a safe

place for them to ride. They may

fall off and be run over or interfere

with the control of the power

machine.

 Never allow children to operate the

power machine, even under adult

supervision.

 Never allow children to play on the

power machine or attachment.

 Use extra caution when backing

up. Before the tractor starts to

move, look down and behind to

make sure the area is clear.

Be Aware of

Signal Words

A signal word designates a degree or

level of hazard seriousness. The

signal words are:

Indicates a hazardous situation that, if

not avoided, will result in death or

serious injury.

Indicates a hazardous situation that, if

not avoided, could result in death or

serious injury.

Indicates a hazardous situation that, if

not avoided, may result in minor or

moderate injury.

WARNING

CAUTION

DANGER

Important Safety Information

4/17/19

Listed below are common practices that may or may not be applicable to the products

described in this manual.

Transport Safely

 Comply with federal, state, and

local laws.

 Use towing vehicle and trailer of

adequate size and capacity. Secure

equipment towed on a trailer with

tie downs and chains.

 Sudden braking can cause a towed

trailer to swerve and upset. Reduce

speed if towed trailer is not

equipped with brakes.

 Avoid contact with any overhead

utility lines or electrically charged

conductors.

 Always drive with load on end of

loader arms low to the ground.

 Always drive straight up and down

steep inclines with heavy end of a

tractor with loader attachment on

the “uphill” side.

 Engage park brake when stopped

on an incline.

 Maximum transport speed for an

attached equipment is 20 mph. DO

NOT EXCEED. Never travel at a

speed which does not allow

adequate control of steering and

stopping. Some rough terrains

require a slower speed.

 As a guideline, use the following

maximum speed weight ratios for

attached equipment:

20 mph when weight of attached

equipment is less than or equal

to the weight of machine towing

the equipment.

10 mph when weight of attached

equipment exceeds weight of

machine towing equipment but

not more than double the weight.

 IMPORTANT: Do not tow a load

that is more than double the weight

of the vehicle towing the load.

Practice Safe Maintenance

 Understand procedure before doing

work. Refer to the Operator’s Manual

for additional information.

 Work on a level surface in a clean

dry area that is well-lit.

 Lower attachment to the ground and

follow all shutdown procedures

before leaving the operator’s seat to

perform maintenance.

 Do not work under any hydraulic

supported equipment. It can settle,

suddenly leak down, or be lowered

accidentally. If it is necessary to work

under the equipment, securely

support it with stands or suitable

blocking beforehand.

 Use properly grounded electrical

outlets and tools.

 Use correct tools and equipment for

the job that are in good condition.

 Allow equipment to cool before

working on it.

 Disconnect battery ground cable (-)

before servicing or adjusting

electrical systems or before welding

on equipment.

 Inspect all parts. Make certain parts

are in good condition & installed

properly.

 Replace parts on this attachment

with genuine Land Pride parts only.

Do not alter this attachment in a way

which will adversely affect its

performance.

 Do not grease or oil attachment

while it is in operation.

 Remove buildup of grease, oil, or

debris.

 Always make sure any material and

waste products from the repair and

maintenance of the attachment are

properly collected and disposed.

 Remove all tools and unused parts

before operation.

Tire Safety

 Tire changing can be dangerous

and must be performed by

trained personnel using the

correct tools and equipment.

 Always maintain correct tire

pressure. Do not inflate tires

above recommended pressures

shown in the Operator’s Manual.

 When inflating tires, use a clip-on

chuck and extension hose long

enough to allow you to stand to

one side and NOT in front of or

over the tire assembly. Use a

safety cage if available.

 Securely support the implement

when changing a wheel.

 When removing and installing

wheels, use wheel handling

equipment adequate for the

weight involved.

 Make sure wheel bolts have been

tightened to the specified torque.

Use A Safety Chain

 A safety chain will help control

drawn machinery should it

separate from the tractor drawbar.

 Use a chain with the strength

rating equal to or greater than the

gross weight of the towed

implement.

 Attach the chain to the tractor

drawbar support or other specified

anchor location. Allow only

enough slack in the chain to

permit turning.

 Always hitch the implement to the

machine towing it. Do not use the

safety chain tow the implement.

Important Safety Information

4/17/19

Listed below are common practices that may or may not be applicable to the products

described in this manual.

Prepare for Emergencies

 Be prepared if a fire starts.

 Keep a first aid kit and fire

extinguisher handy.

 Keep emergency numbers for

doctor, ambulance, hospital, and

fire department near phone.

911

Avoid High

Pressure Fluids Hazard

 Escaping fluid under pressure can

penetrate the skin causing serious

injury.

 Relieve all residual pressure

before disconnecting hydraulic

lines or performing work on the

hydraulic system.

 Make sure all hydraulic fluid

connections are tight and all

hydraulic hoses and lines are in

good condition before applying

pressure to the system.

 Use a piece of paper or

cardboard, NOT BODY PARTS, to

check for suspected leaks.

 Wear protective gloves and safety

glasses or goggles when working

with hydraulic systems.

 DO NOT DELAY. If an accident

occurs, see a doctor familiar with

this type of injury immediately. Any

fluid injected into the skin or eyes

must be treated within

a few hours or

gangrene may

result.

Wear Personal Protective

Equipment (PPE)

 Wear protective clothing and

equipment appropriate for the job

such as safety shoes, safety

glasses, hard hat, and ear plugs.

 Clothing should fit snug without

fringes and pull strings to avoid

entanglement with moving parts.

 Prolonged exposure to loud noise

can cause hearing impairment or

hearing loss. Wear suitable

hearing protection such as

earmuffs or earplugs.

 Operating equipment safely

requires the operator’s full

attention. Avoid wearing

headphones while operating

equipment.

Keep Riders Off

Machinery

 Never carry riders on tractor or

implement.

 Riders obstruct operator’s view

and interfere with the control of

the power machine.

 Riders can be struck by objects or

thrown from the equipment.

 Never use tractor or implement to

lift or transport riders.

Use Safety

Lights and Devices

 Slow moving tractors, and

self-propelled equipment can

create a hazard when driven on

public roads. They are difficult to

see, especially at night. Use the

Slow Moving Vehicle (SMV) sign

when on public roads.

 Flashing warning lights and turn

signals are recommended

whenever driving on public roads.

Use Seat Belt and ROPS

 Land Pride recommends the use

of a CAB or roll-over-protective-

structures (ROPS) and seat belt

in almost all power machines.

Combination of a CAB or ROPS

and seat belt will reduce the risk

of serious injury or death if the

power machine should be upset.

 If ROPS is in the locked-up

position, fasten seat belt snugly

and securely to help protect

against serious injury or death

from falling and machine overturn.

Important Safety Information

4/17/19

Avoid crystalline Silica

(quartz) Dust

Because crystalline silica is a basic

component of sand and granite,

many activities at construction sites

produce dust containing crystalline

silica. Trenching, sawing, and boring

of material containing crystalline

silica can produce dust containing

crystalline silica particles. This dust

can cause serious injury to the

lungs (silicosis).

There are guidelines which should

be followed if crystalline silica

(quartz) is present in the dust.

 Be aware of and follow OSHA

(or other local, State, or Federal)

guidelines for exposure to airborne

crystalline silica.

 Know the work operations where

exposure to crystalline silica may

occur.

 Participate in air monitoring or

training programs offered by the

employer.

 Be aware of and use optional

equipment controls such as water

sprays, local exhaust ventilation,

and enclosed cabs with positive

pressure air conditioning if the

machine has such equipment.

Otherwise respirators shall be worn.

 Where respirators are required, wear

a respirator approved for protection

against crystalline silica containing

dust. Do not alter respirator in any

way. Workers who use tight-fitting

respirators can not have beards/

mustaches which interfere with the

respirator seal to the face.

 If possible, change into disposable

or washable work clothes at the

work site; shower and change into

clean clothing before leaving the

work site.

 Do not eat, drink, use tobacco

products, or apply cosmetics in

areas where there is dust containing

crystalline silica.

 Store food, drink, and personal

belongings away from the work

area.

 Wash hands and face before eating,

drinking, smoking, or applying

cosmetics after leaving the exposure

area.

These are common practices that may or may not be applicable to the products described in

this manual.

Dig Safe - Avoid

Underground Utilities

 USA: Call 811

CAN: digsafecanada.ca

Always contact your local utility

companies (electrical, telephone,

gas, water, sewer, and others)

before digging so that they may

mark the location of any

underground services in the area.

 Be sure to ask how close you can

work to the marks they positioned.

Handle

Chemicals Properly

 Protective clothing should be

worn.

 Handle all chemicals with care.

 Follow instructions on container

label.

 Agricultural chemicals can be

dangerous. Improper use can

seriously injure persons, animals,

plants, soil, and property.

 Inhaling smoke from any type of

chemical fire is a serious health

hazard.

 Store or dispose of unused

chemicals as specified by the

chemical manufacturer.

Important Safety Information

4/17/19

This page left blank intentionally.

Important Safety Information

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

72042

Safety Labels

Your Pallet Fork comes equipped with all safety labels in place.

They were designed to help you safely operate your implement.

Read and follow their directions.

1. Keep all safety labels clean and legible.

2. Refer to this section for proper label placement. Replace

all damaged or missing labels. Order new labels from your

nearest Land Pride dealer. To find your nearest dealer,

visit our dealer locator at www.landpride.com.

3. Some new equipment installed during repair requires

safety labels to be affixed to the replaced component as

specified by Land Pride. When ordering new components

make sure the correct safety labels are included in the

request.

4. Refer to this section for proper label placement.

To install new labels:

a. Clean surface area where label is to be placed.

b. Spray soapy water onto the cleaned area.

c. Peel backing from label and press label firmly onto the

surface.

d. Squeeze out air bubbles with edge of a credit card or

with a similar type of straight edge.

818-798C

Warning: Pinch Point Hazard

Important Safety Information

858-971C

Warning: Lift Capacity & Safe Operation

Important Safety Information

Table of Contents

PFL1242 Pallet Fork 319-211M4/17/19

72042

72043

838-293C

Warning: Read Manual

858-995C

1200 lbs. Lift Capacity

Introduction

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

customer service or repair parts are required. Your Land

Pride dealer has trained personnel, repair parts, and

equipment needed to service the implement.

Serial Number

For quick reference and prompt service, record model

and serial number on the inside cover page and again on

the warranty page. Always provide model number and

serial number when ordering parts and in all

correspondences with your Land Pride dealer. For

location of your serial number plate, see Figure 1.

Serial Number Plate Location

Figure 1

Further Assistance

Your dealer wants you to be satisfied with your new pallet

fork. If for any reason you do not understand any part of

this manual or are not satisfied with the service received,

the following actions are suggested:

1. Discuss any problems you have with your attachment

with your dealership service personnel so they can

address the problem.

2. If you are still not satisfied, seek out the owner or

general manager of the dealership, explain the

question/problem, and request assistance.

3. For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

[email protected]

72042

Introduction

Land Pride welcomes you to the growing family of new

product owners. This Pallet Fork has been designed with

care and built by skilled workers using quality materials.

Proper assembly, maintenance, and safe operating

practices will help you get years of satisfactory use from

this product.

Application

The Land Pride PFL1242 Pallet Fork has uses and

applications in farming, ranching, nurseries, campuses,

theme parks, warehouses, lumber yards, and large or

small retail outlets. This pallet fork will quickly and

conveniently turn your compact and/or sub-compact

tractor loader, equipped with loader arms and universal

quick-attach hitch plate, into a forklift to expand your

material handling capability.

The first two digits in the model number indicate weight

class (PFL1242 = 1,200 lbs) and the last two digits give

fork length (PFL1242 = 42").

For additional information and performance enhancing

options, see “Specifications & Capacities” on page 19

and “Features & Benefits” on page 20.

Using This Manual

•

This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments,

troubleshooting, and maintenance. Read this manual

and follow the recommendations to help ensure safe

and efficient operation.

• The information contained within this manual was

current at the time of printing. Some parts may change

slightly to assure you of the best performance.

• To order a new Operator’s or Parts Manual, contact

your authorized dealer. Manuals can also be

downloaded, free-of-charge, from our website at

www.landpride.com

Terminology

“Right” or “Left” as used in this manual is determined by

facing the direction the machine will operate while in use

unless otherwise stated.

Definitions

Owner Assistance

The dealer should complete the Online Warranty

Registration at the time of purchase. This information is

necessary to provide you with quality customer service.

The parts on your Pallet Fork have been specially

genuine Land Pride parts. Contact a Land Pride dealer if

IMPORTANT: A special point of information related

to the following topic. Land Pride’s intention is this

information must be read & noted before continuing.

NOTE: A special point of information that the

operator should be aware of before continuing.

Section 1: Assembly & Set-Up

Table of Contents

PFL1242 Pallet Fork 319-211M4/17/19

Fork Installation

Figure 1-1

Notched Opening

Pin Notches

72047

Section 1: Assembly & Set-Up

Fork Installation

Refer to Figure 1-1:

CAUTION

To avoid minor or moderate injury:

A pinching hazard exists when installing forks. Do not place

hands or fingers between carrying bars and forks.

1. Raise the fork locking pin (#1) straight up.

2. Center upper end of fork (#2) on upper carrying

bar (#3). Make sure retaining hook (A) is caught

behind upper carrying bar (#3) and retaining

hook (B) fits in notched opening in lower carrying

bar (#4).

3. Slide fork to the right by pushing on the fork near

carrying bars (#3 & #4) until locking pin (#1) is

positioned over one of the pin notches.

4. Lower locking pin handle (#1) to seat pin in the

selected notch. Make sure locking pin is seated and

retaining hooks “A” & “B” are secured behind the

carrying bars.

5. Repeat steps 1-4 for the second fork, but slide the

second fork to the left.

NOTE: Never place 2 forks on the same side of

notch opening. Always have them equal distance

from the center of the frame.

Section 1: Assembly & Set-Up

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures.

Follow these procedures and any additional shutdown

procedures provided in your tractor Operator’s Manual

before leaving the operator’s seat.

1. Reduce engine speed and shut-off all power to the

attachment.

2. Park tractor and attachment on solid, level ground.

3. Lower attachment until it is flat on the ground or on

non-concrete support blocks.

4. Put tractor in park or set park brake, turn off engine,

and remove switch key to prevent unauthorized

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic

lines.

6. Wait for all components to come to a complete stop

before leaving the operator’s seat.

7. Use steps, grab-handles and anti-slip surfaces when

stepping on and off the tractor.

Tractor Hook-Up

Refer to Figure 1-2:

DANGER

To avoid serious injury or death:

A crushing hazard exists while hooking-up and unhooking the

attachment. Do not allow anyone to stand between attachment

and power machine while approaching or backing away from

the attachment. Do not operate lift and/or tilt controls while

someone is near the power machine and/or attachment.

WARNING

To avoid serious injury or death:

• Lightweight power machines may need weight added to the

rear to maintain steering control and prevent forward

tipping or side tipping caused by a heavy front load. Consult

your power machine Operator’s Manual to determine

proper weight requirements and maximum weight

limitations.

• Check hitch fit-up frequently. An improper fit-up can cause

the attachment to come loose from the loader hitch plate

and fall.

• Always shut power machine down following the “Shutdown

Procedure” provided in this manual before leaving the

operator’s seat.

Pallet Fork With Universal Quick Attach Hitch Plate

Figure 1-2

1. If needed, pull locking handles up on loader hitch

until locking pins are fully raised.

2. Carefully drive up to the pallet fork making sure

loader hitch is parallel with the pallet fork hitch plate.

3. Tilt top of loader hitch slightly forward.

4. Place top of loader hitch under the top angled bars

on the pallet fork hitch plate.

5. Slowly lift loader hitch up until hitch and top angle

bars on the pallet fork have come together.

6. Tilt top of loader hitch back to align bottom slots in the

pallet fork hitch plate with locking pins on the loader

hitch.

7. Continue tilting pallet fork back until forks are slightly

higher at the front than at the back. Lower loader

arms until forks are slightly above ground surface.

8. Shut tractor down properly. See “Tractor Shutdown

Procedure”.

9. Push locking handles on loader hitch down until

locking pins fully extend through bottom slots in pallet

fork hitch plate. Make sure locking handles are

locked into position to keep pins from backing out.

Top

Angle Bar

Pallet Fork

Hitch Plate

Bottom Slots

72043

Section 2: Adjustments

Table of Contents

PFL1242 Pallet Fork 319-211M4/17/19

Section 2: Adjustments

Fork Adjustment

Refer to Figure 2-1:

WARNING

To avoid serious injury or death:

Always adjust pallet forks an equal distance away from the

center and as far apart as the pallet will allow. This will

optimize load stability, protect against load shifting, and make

handling the load safer.

CAUTION

To avoid minor or moderate injury:

A pinching hazard exists when repositioning forks. Do not

place hands or fingers between carrying bars and forks.

1. Locate tractor and pallet fork on a flat, level surface.

Place transmission in park or set park brake.

2. Tilt Pallet Fork until front of forks are slightly lower at

the front than at the back. Lower loader arms until

forks are slightly above ground surface.

3. Shut tractor down properly. See “Tractor Shutdown

Procedure” on page 10.

4. Pull the fork locking pin handle (#1A) straight up.

5. Slide pallet fork (#1) to the optimized load carrying

width by pushing or pulling on the fork near the

carrying bars. Be sure to position locking pin (#1A)

directly over one of the five notches in the upper

carrying bar.

6. Lower locking pin (#1A) to seat locking pin in the

selected notch.

• Check locking pin to be sure it has seated.

• Check retaining hooks to be sure they are secured

behind upper and lower carrying bars.

7. Repeat steps 1 to 6 for fork (#2). Make sure both

forks are an equal number of notches away from the

middle of the upper carrying bar.

NOTE: Forks will adjust easier if glide surfaces are

kept lubricated. See “Pallet Fork Contact Points”

on page 17 for lubricating instructions.

Fork Adjustment

Figure 2-1

Upper Carrying Bar

Lower Carrying Bar

Notch locations

Retaining

Hooks

72042

Section 3: Operating Procedures

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

• Always adjust forks so that they are evenly spaced as far

apart as the load will allow and centered on the frame. Keep

load centered on the forks, even when stopped. This will

optimize load stability and protect against load shifting.

• Never lift a load with one fork or more than two forks.

Using one fork will cause the load to be unbalanced. Using

more than two forks will not increase the lift capacity and

can make the job unsafe.

• Always secure equipment with solid, non-concrete supports

before working under it. Never go under equipment

supported by concrete blocks or hydraulics. Concrete can

break, hydraulic lines can burst, and/or hydraulic controls

can be actuated even when power to hydraulics is off.

• Keep attachment, loader arms, and/or load away from

overhead electrical power lines. Place an orange warning

sign under overhead lines indicating type of danger above.

• Always use ROPS & seatbelt warning.

WARNING

To avoid serious injury or death:

• Allow only persons to operate this attachment who have

fully read and comprehended this manual, who are properly

trained to operate the attachment safely, and who are age 16

or older. Serious injury or death can result from the failure

to read, understand, and follow instructions provided in this

manual.

• Never carry riders on the attachment or power machine.

Riders can obstruct the operator’s view, interfere with

control of the equipment, be pinched by moving

components, become entangled in rotating components, be

struck by objects, be thrown or fall from the equipment, etc.

• Hydraulic fluid under high pressure can penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than

hands when searching for leaks. A doctor familiar with this

type of injury must treat the injury within a few hours or

gangrene may result. DO NOT DELAY.

• Do not abuse equipment. Incorrect use of the attachment

can damage equipment structurally and cause serious

injury or death.

• Check pallet fork frequently to make sure it is properly

attached to the loader hitch, forks are secured to the upper

and lower carrying bars, and fork locking pins are seated in

their notches.

• Consult your power machine’s manual for operating

capacity, lifting capacity, and operating specifications.

Exceeding rated capacities and specifications can result in

a roll-over or other serious hazard.

• Always know the weight of the load being lifted. Maximum

lift capacity should never exceed rated lift capacity of the

pallet fork. Also, it should never exceed 83% of the tractor

rated lift capacity. Use the smaller number of the two lift

capacities to determine maximum lift capacity.

Section 3: Operating Procedures

Operating Checklist

Hazard control and accident prevention are dependent

upon the awareness, concern, prudence, and proper

training involved in the operation, transport, storage, and

maintenance of the pallet fork. Therefore, it is absolutely

essential that no one operates this unit unless they are

age 16 or older and have read, fully understood, and are

totally familiar with the Operator’s Manual. Make sure the

operator has paid particular attention to:

Perform the following inspections before using your

Pallet Forks.

Operating Safety

DANGER

To avoid serious injury or death:

• A crushing hazard always exists around equipment

handling palletized loads. Objects on pallet can shift and

fall resulting in death or serious injury.

• Keep bystanders, pets, and livestock away from your work

area. Never allow anyone to go near or under the

attachment or its load. The attachment and/or load can fall.

• Do not drive up to anyone or an animal in front of a fixed

object such as a wall or bench. Never assume that the power

machine will stop in time.

• Use a “spotter” when it is hard to see in the direction you

are traveling and when placing a load that obstructs your

vision. A person or animal could be nearby in a blind spot.

• Never lift objects without pallets and make sure all objects

are secured before lifting them. Use extreme care when

securing round objects to make sure they can’t roll off.

• Lift only objects that have a stable base resting on the

pallet. Uneven, irregular, or round bases can easily tip off

or roll off the pallet.

• Do not lift loads that exceed the load guard height and do

not lift loads that have objects smaller than the openings in

the load guard.

• Keep load slightly tilted back to secure its weight against

the vertical face of the forks. Rotating front of forks too high

can cause the load to shift and fall onto the operator or

others. Rotating front of forks level or lower can cause the

load to fall forward.

Operating Checklist



Check Page

Read and follow all safety rules carefully.

Refer to “Important Safety Information” and

Safety Alert Symbols throughout this manual.

Read and follow assembly instructions.

Refer to “Section 1: Assembly & Set-Up”.

Read and follow all operating procedures

Refer to “Section 3: Operating Procedures”.

Read and follow all maintenance instructions.

Refer to

“Section 4: Maintenance & Lubrication”

Check Pallet Fork initially and periodically for

loose forks, hitch plate, bolts, and pins.

Refer to “Section 8: Torque Values Chart”.

Section 3: Operating Procedures

Table of Contents

PFL1242 Pallet Fork 319-211M4/17/19

• Do not travel across inclines where equipment could slip or

roll-over. Consult your power machine Operator’s Manual

for acceptable inclines they are capable of crossing.

• Do not use forks for digging, pushing, pulling or prying

objects. Only use forks to lift palletized loads.

• Do not use attachment to lift the front or back of the power

machine off the ground. Doing so can damage the

attachment, power machine, and/or cause serious injury or

death.

• Do not chain or strap palletized loads to the loader arms,

loader hitch, pallet fork hitch plate or forks.

• Do not use fork extensions. Fork extensions can damage

forks, pallet fork frame, loader hitch, and overload front of

machine resulting in loss of steering control and load.

• The parts on your pallet fork have been specially designed

and should only be replaced with genuine Land Pride parts.

Altering the equipment can adversely affect its performance

and/or reliability.

• Always lower forks to ground level before dismounting from

the skid steer/tractor. Follow manufacturer’s

recommendations when dismounting and parking the

machine.

• Always store attachment in a secure position so that it will

not fall over.

• Always stack pallets in such a manner that they will not tip

or fall.

Transport Safety

WARNING

To avoid serious injury or death:

• Follow all safety precautions when transporting a load. Not

using safe transporting methods can damage the equipment

and cause serious injury or death.

• Lightweight power machines may need weight added to the

rear to maintain steering control and prevent forward

tipping or side tipping caused by a heavy front load. Consult

your power machine Operator’s Manual to determine

proper weight requirements and maximum weight

limitations.

• Always transport loads as close to the ground as possible

without hitting objects. A load carried high could shift

causing the load to fall, tipping of the machine, and/or loss

of control.

• Transporting loads across inclines, over ramps, on bumpy,

soft, or slippery surfaces reduces machine stability and lift

capacity. Transporting and lifting loads under these

conditions is extremely dangerous. Follow all transport

instructions in your power machine Operator’s Manual.

• Always transport over ramps and inclines with the heavy

end of the power machine on the “uphill” side. This may

require one to drive up and back down inclines.

• When traveling on public roads, use LED lights, slow

moving vehicle sign, clean reflectors, and other adequate

devices to warn operators in other vehicles of your

presence. If implement blocks visibility of slow moving

vehicle sign, relocate sign so it is visible from the back at all

times. Always comply with all federal, state, and local laws.

• When traveling on public roadways, travel in such a way

that faster moving vehicles may pass safely. Use accessory

lights, clean reflectors, and a slow moving vehicle sign that

is visible from the back to warn operators in other vehicles

of your presence. Always comply with all federal, state, and

local laws.

Pallet Fork Operation

Picking up a Load

1. Make sure the load does not exceed the smaller of

two lift capacities:

• Rated lift capacity of the pallet forks.

• 83% of the rated lift capacity of the tractor front

loader.

2. Center forks under the pallet to evenly distribute the

weight.

3. Make sure the load is balanced and secure.

4. Check for overhead obstructions.

5. Stop completely before positioning forks at the

correct height.

6. Drive into the load as far as possible.

7. Lift load just off the ground and tilt it back slightly.

8. Back out slowly to clear racks or other obstacles.

9. Position load at a safe traveling height before

moving. Two to four inches above the floor is

recommended traveling height.

IMPORTANT: Do not attach chain intended for lifting

or securing loads to the pallet fork frame. Doing so

can cause damage to the frame.

IMPORTANT: Using 83% of the rated lift capacity

accounts for increased loader stresses caused by

the added extension of the pallet fork. It also ensures

that the front tires on your tractor are rated properly

for the job.

IMPORTANT: On heavy loads, the center of gravity

should not be positioned farther than 24" away from

the vertical face of the forks. Picking up heavy loads

positioned farther away can damage the unit and

void its warranty.

Section 3: Operating Procedures

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

Traveling with a Load

1. Pedestrians always have the right-of-way.

2. Keep load tilted back slightly.

3. Keep forks low, two to four inches above the floor,

when possible.

4. Continually scan all sides for pedestrians or other

traffic.

5. If load is large and blocks your view, travel in reverse.

6. Always drive at a safe speed and slow down when

going around corners. Avoid sudden braking.

7. Leave enough clearance when turning to keep pallet

forks and load from contacting obstacles such as

storage racks, buildings, trees, or fences.

8. When traveling over a ramp or incline, keep load on

the “uphill” side of the tractor.

9. When possible, travel straight up and down grades,

ramps, and inclines. Avoid making turns on grades,

ramps, and inclines.

10. Raise or lower load only when stopped, never while

traveling.

11. Slow down when traveling over rough or hilly terrain.

12. Do not transport loads on public roadways.

13. When traveling on public roadways, transport in such

a way that faster moving vehicles may pass you

safely.

14. Plan your route to avoid heavy traffic.

Placing a Load

1. Stop in front of desired location to place the load.

2. Slowly raise load to required height.

3. Move forward slowly with load raised until load is

positioned square and straight above its final

destination.

4. Level load to position it for placement.

5. Lower load onto it final resting location.

6. Before backing, check all sides for pedestrians or

other traffic.

7. Once load has settled, back up slowly.

8. Make sure forks clear pallet before turning or

changing fork height.

9. Lower forks before moving again.

Unhooking the Pallet Fork

Refer to Figure 3-1:

1. Park tractor with unit on a flat, level, solid surface and

lower pallet fork until slightly above the surface and

hitch angled with front of pallet forks slightly higher

than rear of pallet forks.

2. Without lowering the Pallet Fork, shut trator down

properly. See “Tractor Shutdown Procedure” on

page 10.

3. Unhook pallet fork as follows:

a. Pull lock handles up to remove pins from bottom

slots in hitch plate.

b. Return to tractor, restart

and tilt top of hitch plate

slightly forward toward the pallet fork.

c. Slowly lower the pallet fork onto the ground until

its top angle bar and loader hitch have separated.

d. Back tractor away slowly from the pallet fork while

making sure the loader hitch does not interfere

with the pallet fork.

Pallet Fork With Loader Mounting Plate

Figure 3-1

72043

Top

Angle Bar

Bottom slots

Section 3: Operating Procedures

Table of Contents

PFL1242 Pallet Fork 319-211M4/17/19

General Operating Instructions

By now you should have familiarized yourself with the

Operator’s Manual for your Pallet Fork.

If you haven’t, please do so now. We cannot overstress

the importance of following the safety operating

procedures that are spelled out in this Manual.

Proceed by getting onto the tractor seat, fastening

seatbelt and starting tractor. It isn’t going to take you long

to learn how to use your new Land Pride Pallet Fork.

We recommend that you take a little time to practice

securely attaching and detaching your pallet fork to and

from your tractor universal quick-attach hitch. It is also

important to practice lifting, lowering, maneuvering, and

placing an empty pallet on a level site until you gain the

confidence and skill needed to have a good feel in what

you are doing.

As you quickly become more skilled and adept in using

your Pallet Fork, you will soon learn that it is always more

important to focus on the don’ts than it is to focus on the

dos. For example, don’t exceed the lift capacity of your

forks or tractor. Don’t lift your load too high creating an

unstable load and unsafe situation. Don’t tilt your load too

far backwards, setting up a situation that could cause

your load to roll or spill backwards onto you, the tractor,

and the operator’s platform. Don’t drive too fast for your

ground and load conditions. Don’t work on or around

slippery or sloped areas that could cause you to lose

control of the tractor. Don’t allow pedestrians, pets, or

livestock to approach the danger zone of your working

area. Don’t leave your tractor with forks or load raised off

of the ground.

If you just follow these few safety reminders, you will find

that you will quickly become very adept, handy, and

skillful at using your Land Pride pallet fork.

See “Specifications & Capacities” on page 19 and

“Features & Benefits” on page 20 of your Operator’s

Manual for additional information.

Section 4: Maintenance & Lubrication

Table of Contents

PFL1242 Pallet Fork 319-211M 4/17/19

Maintenance

DANGER

To avoid serious injury or death:

Always secure equipment with solid, non-concrete supports

before working under it. Never go under equipment supported

by concrete blocks or hydraulics. Concrete can break,

hydraulic lines can burst, and/or hydraulic controls can be

actuated even when power to hydraulics is off.

WARNING

To avoid serious injury or death:

• Perform scheduled maintenance. Check for loose

hardware, missing parts, broken parts, structural cracks,

and excessive wear. Make repairs before putting implement

back into service.

• Do not alter implement or replace parts on the implement

with other brands. Other brands may not fit properly or

meet OEM (Original Equipment Manufacturer)

specifications. They can weaken the integrity and impair the

safety, function, performance, and life of the implement.

Replace parts only with genuine OEM parts.

Proper servicing and adjustments are key to the long life

of any implement. With careful inspection and routine

maintenance, you can avoid costly downtime and repair.

1. After using your pallet fork for a few lifts, check forks

to make sure they are still secured and check pallet

fork to make sure it is still properly attached to the

loader hitch.

2. Check forks to make sure they are not damaged,

broken, or worn excessively. Repair or replace as

needed.

3. Always remove any material that has become

entangled in the forks before continuing to use them.

4. Replace any worn, damaged, or illegible safety

labels by obtaining new labels from your Land Pride

dealer.

Long-Term Storage

Clean, inspect, service, and make necessary repairs to

the attachment when storing it for long periods and at the

end of the season. This will help ensure the unit is ready

for field use the next time you hook-up to it.

1. Remove any dirt and grease that may have

accumulated on the pallet fork. Scrape off compacted

dirt and then wash its surface thoroughly with a

garden hose.

2. Inspect pallet fork for loose, damaged, or worn parts

and adjust or replace when needed.

3. Repaint parts where paint is worn or scratched to

prevent rust. Ask your Land Pride dealer for aerosol

touch-up paint. Paint is also available in touch-up

bottles with brush, quarts, and gallon sizes by adding

TU, QT, or GL to the end of the aerosol part number.

Section 4: Maintenance & Lubrication

4. Replace all damaged or missing decals.

5. A coating of oil may also be applied to areas where

paint is worn off to minimize oxidation.

6. Store pallet fork inside a building and away from

human activity if possible. Inside storage will reduce

maintenance and make for a longer life.

7. Follow all unhooking instructions on page 14 when

disconnecting a tractor from the Pallet Fork.

8. Do not allow children to play on or around the stored

pallet fork.

Land Pride Touch-up Paint

Part No. Part Description

821-070C PAINT GP GLOSS BLACK SPRAY CAN

Page is loading ...

Land Pride PFL12 Series User manual

Brand: Land Pride

Model: PFL12 Series

Type: User manual

This manual is also suitable for

PFL12

Download PDF

report

Land Pride PFL12 Series User manual

This manual is also suitable for

Land Pride PFL12 Series User manual

Related papers

Other documents