LG SP182CM Owner's manual

Brand: LG

Model: SP182CM

Type: Owner's manual

This manual is also suitable for

OWNER’S MANUAL

AIR CONDITIONER

Please read this manual carefully before operating

your set and retain it for future reference.

P/NO:MFL68070403

www.lg.com

SP242CM

U56

TYPE:WALL MOUNTED

MODELS

SP182CM

U56

SP242CM

N56

SP182CM

N56

ENGLISH

ESPAÑOL

2 Room Air Conditioner

Room Air Conditioner Owner’s Manual

TABLE OF CONTENTS

Display Luminosity(Optional) ..............15

Energy-Saving Cooling Model ............15

........................................16

To Cancle The Timer Setting...............16

Sleep Mode Operation ........................16

......................

Jet Cool

Operation...............................17

Forced Operation.................................17

E. Maintenance and Service..................18

Indoor Unit...........................................18

Outdoor Unit ........................................20

Operation Tips!....................................20

Self-Diagnosis Function ......................20

Troubleshooting Tips!

Save time and money!.........................21

Call the service immediately in the

following situations ..............................21

Spec sheet...........................................22

A. Safety Precautions ..............................3

B. Electrical Safety...................................6

Temporary Use of an Adapter ...............6

Temporary Use of an Extension Cord ...6

Symbols used in this Manual.................6

C. Product Introduction...........................7

Indoor Units ...........................................7

Operation Indication Lamps ..................8

Outdoor Unit ..........................................8

D. Operating Instructions........................9

How to insert the Batteries ....................9

Wireless Remote Controller

Maintenance..........................................9

Operating Method..................................9

Wireless Remote Controller

Operation Mode...................................12

.....13

Air Circulation Operation

.....................14

Auto Clean Operation..........................14

Cooling Only Model ..........................10

Wireless Remote Controller

Heat Pump Model .............................11

Horizontal Vane Control

Auto Operation.....................................13

Healthy Dehumidification Operation

Timer Setting

Setting the Current Time......................15

FOR YOUR RECORDS

Write the model and serial numbers here:

You’ll find many answers to common problems in the

Inside you will find many helpful hints on how to use

You can find them on a label on the side of each unit.

Model #

Serial #

Dealer's Name

Date Purchased

Staple your receipt to this page in the event you need

it to prove date of purchase or for warranty issues.

READ THIS MANUAL

and maintain your air conditioner properly. Just a little

preventive care on your part can save you a great deal

of time and money over the life of your air conditioner.

chart of troubleshooting tips. If you review our chart of

Troubleshooting Tips

for service at all.

first, you may not need to call

PRECAUTION

• Contact the authorized service technician for

repair or maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by

young children or invalids without supervision.

• Young children should be supervised to ensure

that they do not play with the air conditioner.

• When the power cord is to be replaced,

replacement work shall be performed by

authorized personnel only using only genuine

replacement parts.

• This appliance is not intended for use by persons

(including children) with reduced physical,sen-

sory or mental capabilities, or lack of experience

and knowledge, unless they have been given su-

pervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

WARNING: Before accessing the terminals, all

power circuits must be disconnected.

WARNING: Fixed installations will incorporate

disconnect means in accordance with

installation rules.

WARNING: This device will not be accessible to

public.

WARNING: The appliance must be installed in

accordance with national regulations

for electrical installations.

Plug in the power plug properly.

Otherwise, it will cause electric shock or fire due to heat generation or electric shock.

Do not operate or stop the unit by inserting or pulling out the power plug.

Do not operate with wet hands or in damp environment.

Do not direct airflow at room occupants only.

Do not allow water to run into electric parts.

Do not use the socket if it is loose or damaged.

Do not open the entrance during operation.

Always perform grounding work.

Always install air leakage breaker and a dedicated switching board.

Unplug the unit if strange sounds,smell,or smoke comes from it.

It will cause electric shock or fire due to heat generation.

In the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

Do not damage or use an unspecified power cord.

It will cause electric shock or fire.

It will cause electric shock or fire due to heat generation.

It may cause electric shock.

It may cause failure of machine or electric shock.

No grounding may cause electric shock.

No installation may cause fire and electric shock accident.

It may cause fire and electric shock accident.

It may cause fire and electric shock.

It may cause electric shock.

This could damage your health.

Do not modify power cord length or share the outlet with other appliances.

quallfied order to avoid a hazard.(Y Attachment)

ENGLISH

There is risk of fire or electric shock.

Avoid personal injury.

It may cause corrosion on the product.

A bad connection may cause water leakage.

Install the drain hose to ensure that the condensed water is drained away properly.

Do not use the telephone or turn switches on or off. There is risk of explosion or fire.

product on.

Two or more peopie must lift and transport the product.

Do not install the product where it will be exposed to sea wind (salt spray) directly.

Do not place ANYTHING on the power cable.

Do not plug or unplug the power supply plug to turn the unit ON/OFF.

When flammable gas leaks, turn off the gas and open a window for ventilation before turn the

Harsh detergent may also cause failure of product, fire, or electronic shock.

Do not use harsh detergent that causes corrosion or damage on the unit.

For inner cleaning, contact an Authorized Service Center or a dealer.

Indoor/outdoor wiring connections must be secured tightly and the cable should be routed properly

so that there is no force pulling the cable from the connection terminals.

Safely dispose off the packing materials. Like screws, nails, batteries, broken things etc after

Improper or loose connections can cause heat generation or fire.

Make sure to check that the power cable plug is not dirty, loose or broken and then only insert the

Children may play with them and cause injury.

Incorrect refrigerant used can prevent the normal operation of the unit.

Don’t use a power cord, a plug or a loose socket which is damaged.

Otherwise it may cause a fire or electrical shock.

Do not touch, operate, or repair the product with wet hands. Hold the plug by hand when taking out.

Do not place a heater or other heating appliances near the power cable.

Do not allow water to run into electric parts.Install the unit away from water sources.

Do not store or use or even allow flammable gas or combustibles near the product.

Do not use the product in a tightly closed space for a long time. Perform ventilaion regularly.

Do not open the front grille of the product during operation. (Do not touch the electrostatic filter, if

If strange sounds, smell or smoke comes from product. Immediately turn the breaker off or

Be sure to check the refrigerant to the used. Please read the label on the product.

Dirty, loose or broken power plug can cause electric shock or fire.

plug completely.

installation or svc and then tear away and thraw away the plastic packaging bags.

There is risk of electric shock or fire.

There is risk of fire and electric shock.

There is risk of electric shock or fire.

There is risk of electric shock.

There is risk of product damage or failure, or unintended operation.

There is risk of fire or electric shock.

This could result in personal injury and product damage.

Take care to ensure that nobody especially kids could step on or fall onto the outdoor unit.

Take care to ensure that power cable could not be pulled out or damaged during operation.

breaker.

When the product is not to be used for a long time, disconnect the power supply plug or turn off the

element etc.

Turn the main power off and unplug the unit when cleaning or repairing the product.

There is risk of fire, failure of the product, or electric shock.

There is risk of fire.

There is risk of physical injury, electric shock, or product failure.

the unit is so equipped.)

disconnect the power supply cable.

Ventilate the product room from time to time when operating it together with a stove, or heating

Oxygen deficiency could occur and hence harm your health.

Oxygen deficiency can occur and hence harm your health.

It may cause a problem for your neighbors and hence dispute.

Low refrigerant levels may cause failure of product.

There is risk of damage or loss of property.

It may cause product failure.

Do not touch the metal parts of the product when removing the air filter.

Do not step on or put anyting on the product. (outdoor units)

Always insert the filter securely after cleaning. Clean the filter every two weeks or more often if

Be cautious when unpacking and installing the product.

If the refrigerant gas leaks during the repair, do not touch the leakaing refrigerant gas.

There is risk of fire, electric shock, or damage to the plastic parts of the product.

There is risk of personal injury.

necessary.

There is risk of personal injury and failure of product.

There are sharp and moving parts that could cause personal injury.

A dirty filter reduces the efficiency.

Sharp edges could cause injury.

Do not tilt the unit when removing or uninstalling it.

Do not mix air or gas other than the specified refrigerant used in the system.

The refrigernat gas can cause frostbite (cold burn)

The condensed water inside can spill.

damage or injury.

Replace the all batteries in the remote control with new ones of the same type. Do not mix old and

accordance with local and national standards.

If the refrigerant gas leaks during the installation, ventilate the area immediately.

Dismantling the unit, treatment of the refrigerant oil and eventual parts should be done in

If air enters the refrigerant system, an excessiveiy high pressure results, causing equipment

Otherwise it can be harmfull for your health.

There is risk of fire or product failure.

There may bum or explode.

Moisture may condense and wet or damage furniture.

This could harm to your health.

It is not sanitary and could cause serious health issues.

Be careful and avoid personal injury.

The chemicals in batteries could cause burns or other health hazards.

use the remote if the batteries have leaked.

window is left open.

Do not expose your skin or kids or plants to the cool or hot air draft.

Do not drink the water drained from the product.

Use a firm stool or ladder when cleaning, maintaining or repairing the product at an height.

Do not let the air conditioner run for a long time when the humidity is very high and a door or a

If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not

new batteries or different types of batteries.

Do not recharge or disassemble the batteries. Do not dispose off batteries in a fire.

Do not insert hands or other objects through the air inlet or outlet while the product is operating.

consumer air conditioner, not a precision refrigeration system.

Do not block the inlet or outlet of air flow.

Use a soft cloth to clean. Do not use harsh detergents, solvents or splashing water etc.

Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a

Always check for gas (refrigerant) leakage after installation or repair of product.

To avoid vibration or noise.

the neighborhoods.

Do not install the product where the noise or hot air from the outdoor unit could damage or disturb

Keep level even when installing the product.

ENGLISH

WARNING: Before accessing the terminals, all power circuits must be disconnected.

WARNING: This device will not be accessible to the public.

WARNING: The appliance must be installed in accordance with national regulations for electrical

installations.

6 Room Air Conditioner

Electrical Safety

• This appliance must be properly grounded.

To minimize the risk of electric shock, you must alway plug into a grounded oulet.

• Do not cut or remove the grounding prong from the power plug.

• Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance

unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the

house wiring.

• If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and

circuit checked by a qualified electrician.

We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections,

use only a genuine adapter, available from most local hardware stores. Ensure that the large slot in the

adapter is aligned with the large slot in the receptacle for a proper polarity connection.

To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground

terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage.

• Never use the appliance with a broken adapter.

We strongly discourage the use of an extension cord due to potential safety hazards.

Temporary Use of an Adapter

Temporary Use of an Extension Cord

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that may cause harm to the

air conditioner.

This symbol indicates special notes.

NOTE

Symbols used in this Manual

This appliance should be installed in accordance with national wiring regulations. This guide acts as a

guide to help to explain product features.

Owner's Manual 7

Here is a brief introduction of the indoor and outdoor units. Please see the information specific to your

indoor unit type.

Product Introduction

Standard Split Type

Art Cool Type Wide

Display panel LED indicators

Indoor Units

Art Cool Deluxe(Type 1)

Display panel LED indicators

ENGLISH

Signal receiver

Front panel

Air discharge

Power cord

ON/OFF button

Plasma filter

Air inlet

Air filter

Art Cool Deluxe(Type 2)

Display panel LCD indicators

Signal receiver

Front panel

Air discharge

ON/OFF button

Power cord

Plasma filter

Air inlet

Air filter

Air Inlet

Signal Receptor

ON/OFF Button

Front Panel

Air Filter

8 Room Air Conditioner

Product Introduction

Air intake vents

Air outlet vents

Connecting

wires

Refrigerant pipes

Drain hose

Base plate

On/Off

: Lights up during the system operation, error code and auto restart setting.

Sleep mode : Lights up during sleep mode auto operation.(non-Inverter Model)

Plasma : The function illustrates its dynamic mode by using a multiple lighting system.

Timer

: Lights up during timer operation.(non-Inverter Model)

Lights up during timer operation or sleep mode auto operation (Inverter Model only)

Defrost mode

Power Display : Indicates the setting temperature and operation mode.

: Lights up during defrost mode or hot start operation (Heat pump model only)

: Lights up during outdoor unit operation. (Cooling model only)

Outdoor unit

operation

OUT

DOOR

! Hot start operation: Stops the indoor fan in heating operation for minutes to prevent cold air from blowing out

from unit.

! In defrost mode unit stops heating operation for few minutes to remove formation of ice on the heat

exchanger coils to maintain the efficiency.

Operation

mode

Shape of

display

Setting

temperature

Standard Too hot Hot Cold Too cold

Jet

Cool/Heat

Test

operation

Auto

clean

Comfortable

Auto operation mode

Cooling, heating,

Dehumidification

Mode

Energy-saving

cooling mode

Outdoor Unit

Operation Indication Lamps

Choose a suitable place where its safe & easy to reach.

2. Fix the holder to wall etc with the supplied

screws firmly.

3. Slide the remote controller inside the holder.

1. Remote controller should never be exposed to

direct sunlight.

2. Signal transmitter & receiver should always be

clean for proper communication. Use a soft

cloth to clean them.

NOTE

Operating Instructions

How to insert the Batteries

Wireless Remote Controller Maintenance

1. Remove the battery cover by pulling it according to the arrow direction.

2. Insert new batteries making sure that the (+) and (-) of battery are

installed correctly.

3. Reattach the cover by sliding it back into position.

1. Always use/replace both batteries of same type.

2. If the system is not to be used for a long time, remove the batteries to

save their working life.

3. If the display screen of remote controller starts, fading replace both of

the batteries.

4. Use 2 AAA(1.5 volt) batteries.

NOTE

3. In case some other appliances also get operated with remote control, change their position or consult

your serviceman.

1. The signal receiver is inside the unit.

Aim the remote controller towards the unit to operate it. There should not be any blockage in between.

Operating Method

Owner's Manual 9

Operating Instructions

ENGLISH

Room Air Conditioner 10

ENGLISH

Operating Instructions

• Reset (display): When you press the reset button, all the functions shown on the screen of remote

controller (above image), will be visible on the display. But some of these functions are optional for

your product and may not actually function.

Wireless Remote Controller (Cooling Only Model)

Display screen

Control panel

JET

COOL

JET

COOL

* Some functions may not be supported, depending on the

model.

Control

panel

Display

screen

Description

Fan button : Air come out from the

indoor unit below to the room without

air temperature change.

Sleep mode auto button*: Sets the

sleep mode auto operation.

Temperature adjustment buttons:

Adjusts the room temperature when

cooling and heating.

On/Off button: Turns the power

on/off.

Indoor fan speed button: Adjusts the

fan speed.

Operation mode selection button*:

Selects the operation mode.

Cooling operation ( ) /

Auto operation ( ) /

Dehumidifying operation ( )

Jet cooling*:

cools down the indoor

temperature within a short period of

time.

Air flow direction button: Adjusts the

air flow direction vertically.

Temperature display button: Displays

the room temperature. Press for

5 sec, conversion °C / °F

Timer button: Sets the current time

and the start / end time.

Navigation and functions button*:

Adjusts the time and sets the special

functions.

: Auto clean / : Operates energy

saving cooling

Set/clear button: Sets or cancels

functions.

Reset button : Resets the remote

control settings.

LIGHT button: Adjusts the brightness

of the indoor unit display.

Owner's Manual

Operating Instructions

Wireless Remote Controller (Heat Pump Model)

• Reset (display): When you press the reset button, all the functions shown on the screen of remote

controller (above image), will be visible on the display. But some of these functions are optional for

your product and may not actually function.

Display screen

Control panel

JET

COOL

JET

COOL

* Some functions may not be supported, depending on the

model.

Control

panel

Display

screen

Description

Fan button : Air come out from the

indoor unit below to the room without

air temperature change.

Sleep mode auto button*: Sets the

sleep mode auto operation.

Temperature adjustment buttons:

Adjusts the room temperature when

cooling and heating.

On/Off button: Turns the power

on/off.

Indoor fan speed button: Adjusts the

fan speed.

Operation mode selection button*:

Selects the operation mode.

Cooling operation (

) /

Auto changeover (

) /

Dehumidifying operation (

) / Heating

operation ( )

Jet cooling*:

cools down the indoor

temperature within a short period of

time.

Air flow direction button: Adjusts the

air flow direction vertically.

Temperature display button: Displays

the room temperature. Press for

5 sec, conversion °C / °F

Timer button: Sets the current time

and the start / end time.

Navigation and functions button*:

Adjusts the time and sets the special

functions.

: Auto clean / : Operates energy

saving cooling

Set/clear button: Sets or cancels

functions.

Reset button : Resets the remote

control settings.

LIGHT button: Adjusts the brightness

of the indoor unit display.

ENGLISH

Heating

(Heat pump model only)

Dehumidification

Auto

Operation

Cooling

Press the ON/OFF BUTTON to turn the unit on.

The unit will respond with a beep.

Press the operation mode button. Each time the button is pressed,

the operation mode is shifted in the direction of the arrow.

For cooling operation set the desired indoor temperature by

pressing the ROOM TEMPERATURE SETTING BUTTONS.

For cooling the temperature can be set within 18°C~30°C and

Set the fan speed with the remote controller. You can select the fan speed.

Natural wind

For fresher feeling, press the INDOOR FAN SPEED SELECTION BUTTON and set to Natural wind mode.

In this mode, the wind blows like a natural breeze by automatically changing fan speed.

Operation Mode

12 Room Air Conditioner

Operating Instructions

for heating the temperature range is 16°C~30°C.

Step1(Low) Step2(Medium) Step3(High)Natural Wind

Owner's Manual 13

Operating Instructions

During Healthy Dehumidification Operation

If you select the dehumidification mode on the OPERATION MODE

SELECTION BUTTON, the product starts to run the dehumidification

function.

It automatically sets the room temperature and airflow volume to the best

condition for dehumidification, based on the sensed current room

temperature.

In this case, however, the setting temperature is not displayed on the remote

controller and you are not able to control the room temperature either.

During the healthy dehumidification function, the fan speed is automatically

set according to the optimization algorithm responding to the current room

temperature status, so that the room condition is kept healthy and

comfortable even in the very humid season.

Healthy Dehumidification Operation

The temperature and fan speed are automatically set by the electronic

controls based on the

actual room temperature.

If you feel hot or cold, press TEMPERATURE SETTING buttons for more

cooling or heating effect.

You cannot switch the indoor fan speed. It has already been set by the

Auto Operation Mode rule.

Auto Operation

Code Description

2 Cool

1 Cool slightly

0 Maintain

room

temperature

-1 Heat slightly

-2 Heat

You can set desired temperature and indoor fan speed.

Setting Temp. Range : 18~30°C.

: You can not set the actual setting temperature and the fan

speed in this operation mode. But you can use the Auto swing

in this operation. If the system is not operating as desired,

switch manually to another mode

NOTE

ENGLISH

14 Room Air Conditioner

During Auto Clean Operation, moistures left in indoor units after cooling operation or healthy

dehumidification operation can be removed.

Select Auto Clean Operation by the function setting button( ) .

Now whenever the unit is turned off, the indoor fan is still running

for about 30 minutes internally without cooling or dehumidification

operation. This function dries up any remains of moisture & cleans

the unit internally. If you push the Auto Clean button again, this

function is cancelled.

During Auto Clean fuction, only ON/OFF button, Plasma button, Auto Clean

button is used. During this operation, 'Cooling' lamp lights up.

NOTE

Auto Clean Operation

This operation circulates the air without cooling. It can be activated

by pressing the OPERATION MODE SELECTION BUTTON. Once

the air circulation is activated you can select the fan speed by

pressing the INDOOR FAN SPEED SELECTION BUTTON.

Air Circulation Operation

Operating Instructions

Owner's Manual 15

Operating Instructions

Energy-Saving Cooling Mode

Energy-saving cooling mode can save energy in cooling operation, because it can operate efficiently by

setting body-adaptation time according to the change of time and temperature and adjusting desired

temperature automatically.

1. Press the ON/OFF BUTTON to start the unit.

2. Select cooling operation.

3. Press the ENERGY-SAVING COOLING MODE BUTTON.

4. To cancel the energy-saving cooling mode, press the ENERGY-SAVING

COOLING MODE BUTTON again and unit will operate in previous

mode(Cooling mode), but temperature remains 22°C.

Display Luminosity

The unit display Luminosity can be adjusted by using the remote controller.

Press the LED LUMINOSITY button.

Display LED will be dark. Press the button again to set bright display.

Press the SET CLEAR BOTTON For 3 seconds.

Press the TIMER SETTING BUTTONS until the desired time is set.

Check the indicator for a.m. and p.m.

NOTE

Setting the Current T ime

Press the SET/CLEAR button.

ENGLISH

16 Room Air Conditioner

To cancel the timer setting

Timer Setting

Press the SLEEP Button to set the time, you can adjust the time by pressing Setting Button.

Press the SET/CLEAR BUTTON

SLEEP MODE AUTO BUTTON 1 to 7 times. The sleep mode is available for 1 to 7 hours.

• The sleep mode will operate indoor fan at super low speed in cooling mode for pleasant sleep.

In cooling mode or healthy dehumidification mode:

The setting temperature will rise automatically two times by 1°C over next consecutive 30 minutes

(Maximum 2°C) for a comfortable sleep. This will be the final setting temperature as long as sleep mode is

functioning.

NOTE

Sleep Mode Operation

Press the Timer button once to set on the

Reserved 'On' or 'Off'.

Press the Time Setting buttons until the

desired time is set.

Press the SET/CLEAR BUTTON

Description

Button on the

Indication on the LCD Display

Remote Controller

• If you wish to cancel all timer setting, press the SET/CLEAR button.

Operating Instructions

Owner's Manual 17

ON/OFF

button

Operating Instructions

ENGLISH

1. To adjust the direction of the air flow horizontally, press

repeatedly and select the desired

direction.

- Select

to adjust the direction of the air flow automatically.

2. To adjust the direction of the air flow vertically, press

repeatedly and select the desired direction.

- Select

to adjust the direction of the air flow automatically.

Horizontal Vane Control

Jet Cool Operation

Jet cool function can be used to cool the room quickly in hot summer. When this

function is turned on, the air conditioner runs in cooling operation mode with super

high fan speed and 18°C setting temperature for 30 minutes for fast and effective

cooling.

You can activate this operation by pressing the JET COOL BUTTON.

To change from jet cool mode to high fan speed cooling mode, press the JET COOL BUTTON or

INDOOR FAN SPEED SELECTOR BUTTON or the ROOM TEMPERATURE SETTING BUTTON again.

• Jet Cool operation cannot be activated during Air Circulation operation.

NOTE

• Adjusting the air flow direction vertically may not be supported, depending on the model.

• Adjusting the air deflector arbitrarily may cause product failure.

• If you restart the air conditioner, it starts to operate with the previously set direction of air flow, so the air

deflector may not match the icon displayed on the remote control. When this occurs, press

adjust the direction of the air flow again.

NOTE

JET

COOL

Forced operation

Forced operation is used when the remote controller can't be used. The operation will be started if the ON/OFF

button is pressed. If you want to stop the operation, re-press the button.

Heat pump Model

Cooling Model

Room Temp. ≥ 24°C 21°C ≤ Room Temp. < 24°C Room Temp. < 21°C

Operating mode Cooling Cooling Healthy Dehumidification Heating

Indoor FAN Speed

High High High High

Setting Temperature

22°C 22°C 23°C 24°C

Maintenance and Service

Indoor Unit

Before performing any maintenance, turn off the main power to the system, disconnect the circuit breaker and

unplug the power cord.

Clean the unit with a soft dry cloth. Do not use bleach or abrasives.

Never use any of these

• Water hotter than 40°C. It may cause deformation and discoloration.

• Volatile substances. They may damage the surface of the air conditioner.

Air Filters

The air filters behind the front panel / grill should be checked and

cleaned once in every 2 weeks or more often if necessary. To

remove the filters see the self explanatory diagrams for each

model type. Clean the filters with a vacuum cleaner or warm

soapy water. If dirt is not easily removed, wash with a solution of

detergent in luke warm water. Dry well in shade after washing and

reinstall the filters back in place.

Plasma Filters (Optional)

The plasma filters behind the air filter should be checked and

cleaned once in every 3 months or more often if necessary. To

remove the filters see the self explanatory diagrams for each

model type. Clean the filters with a vacuum cleaner. If it is dirty

wash it with water and dry well in shade an install back in place.

18 Room Air Conditioner

Maintenance and Service

• Do not washed the 3M filter with water, because the filter can be damaged.

MULTI Protection Filter

The multi protection filter behind the air filter should be checked and

cleaned once in every 1 month or more often if necessary. To remove the

filters see the self explanatory diagrams for each model type. Clean the filters with

a vacuum cleaner. Do not wash the multi protection filter with water, because the filter

can be damaged. And then insert the filter into original position.

•

We suggest changing multi protection filter every 6 months.

The location of the filters may differ, depending on the model.

If you need more filters,please contract the LG service center

(refer to the warranty card,)

•

Pull out the multi protection filter from the separately packed plastic bag.

Installation of new multi protection filter

•

Insert the multi protection filter into the case.

•

Multi protection filter is installed with 3M Mark front.

Test operation

During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room temperature

and resets in 18 minutes.

During test operation, if remote controller signal is received, the unit operates as remote controller

sets.

If you want to use this operation, Press and hold the ON/OFF button for 3~5 seconds, then the buzzer sound 1

'beep'. If you want to stop the operation, re-press the button.

1. Deluxe (Type 1):

Open the upside of the panel and lift it up as shown. The hooks of the panel will come off. Remove the

air filters. Then pull out the plasma filter

2. Deluxe (Type 2):

Open the front panel as shown.

Then pull the filter tab slightly forward to remove the air filter.

After removing the air filter remove the plasma and deodorizer filter by slightly pulling forward.

After cleaning and drying well reinstall the filters in their original position.

Front panel

Panel hook

Plasma filter

Front panel

3. Standard Split Type : Two different methods to open the front panel based on types of air

conditioner as below ;

Type 1: Open the front panel as shown.

Then pull the filter tab slightly forward to remove the air filter.

After removing the air filter remove the plasma and 3M multi protection filter by slightly pulling

forward.

How to use the front panel

1. Front panel closing

Move the link upward and close the front panel.

2. Front panel removing

Raise the link up to hook hanger and remove

front panel forward.

Plasma filter

(optional)

MULTI

protection filter

Owner's Manual 19

Maintenance and Service

Removal of Filters

Don't touch this plasma filter within 10 seconds after opening the inlet grille, it may cause an electric shock.

ENGLISH

Outdoor Unit

The heat exchanger coils and panel vents of the outdoor unit should be checked regularly.

If clogged with dirt or soot, the heat exchanger

and panel vents may be professionally steam cleaned.

Dirty or clogged coils will reduce the operating efficiency of the system and cause higher operating costs.

NOTE

Operation Tips!

Self-Diagnosis Function

Error Display LED ( )

Check Point

• Indoor room temperature thermistor open/short.!

• Indoor pipe temperature thermistor open/short.

(once)

3 sec 3 sec 3 sec

This unit has an inbuilt error diagnosis capability. Unit LED( ) will blink in case if thermistor fails.

Please contact your serviceman/dealer in such a situation

Do not overcool the room.

This is not good for the health and

wastes electricity.

Keep blinds or curtains

closed.

Do not let direct sunshine enter

the room when the air conditioner

is in operation.

Keep the room temperature

uniform.

Adjust the vertical and horizontal

airflow direction to ensure a

uniform temperature in the room.

Make sure that the

doors and windows

are shut thight.

Avoid opening doors and

windows as much as

possible to keep the cool

air in the room.

Clean the air filter

regularly.

Blockages in the air filter

reduce the airflow and

lower cooling and

dehumidifying effects.

Clean at least once every

two weeks.

Ventilate the room

occasionally.

Since windows are kept

closed, it is a good idea

to open them and

ventilate the room now

and ten.

Use high fan speed

for effective and fast

cooling.

The unit gives its rated

cooling capacity when the

fan speed is high.

Don't touch this plasma filter within 10 seconds after opening the inlet grille, it may cause an electric shock.

Type 2: Pull the front panel from both sides as shown.

Then pull the filter tab slightly forward to remove the filter. After removing the air filter remove

the plasma and triple deodorizer filter by slightly pulling forward.

Plasma filter

Deodorizer

filter

20 Room Air Conditioner

Maintenance and Service

Page is loading ...

LG SP182CM Owner's manual

Brand: LG

Model: SP182CM

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: LG SP182CM El manual del propietario

LG SP182CM Owner's manual

This manual is also suitable for

LG SP182CM Owner's manual

in other languages

Related papers

Other documents