1 CPS-CAB-S02-1
CONPROSYS Series
CPS-CAB-S02-1 Product Guide
CONTEC CO., LTD.
CPS-CAB-S02-1 are cables to connect the MITSUBISHI CNC and the CONPROSYS series CNC
communication support controller(s).
External Dimensions
Specifications
Item
Specifications
Connector used
20-pin connector 10120-3000PE [3M] or equivalent
9-pin D-SUB connector 17JE-13090-02(D1)A [DDK] or equivalent
Cable
10 core shield cable (5pair). Conductor size: AWG#28
Conductor composition: 7pcs/0.127mm UL20276
Weight 150g (Max.)
Connection Diagram
*
The shell of 9-pin D-SUB connector is unconnected.
1
6
5
9
1
6
5 9
1
10
11
20
1000
+50
-0
[mm]
20pin Connector 9pin D-sub Connector
CN1 pin CN2 pin
0V 1 SG 5
SD1(TxD1) 12 RD 2
RD1(RXD1) 2 SD 3
RS1(RTS1) 13 CS 8
CS1(CTS1) 3 RS 7
ER1(DTR1) 14 DR 6
DR1(DSR1) 4 ER 4
CD 1
RI 9
0V 5
N.C. 6 Shell -
N.C. 10
0V 15
N.C. 16 9pin D-sub Connector
N.C. 20
CN3 pin
0V 11 SG 5
SD2(TxD2) 17 RD 2
RD2(RxD2) 7 SD 3
RS2(RTS2) 18 CS 8
Cs2(CTS2) 8 RS 7
ER2(DTR) 19 DR 6
DR2(DSR2) 9 ER 4
CD 1
RI 9
Shell - Shell -
Shield
Shield
Cable
Cable
CPS-CAB-S02-1 Product Guide
CONTEC CO., LTD. April 2018 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
https://www.contec.com/ NA06115 (LYVW141)
[04132018]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Notes!
Caution
- Do not strike or bend the product. Otherwise, the product may malfunction, overheat, break or be damaged.
- Do not insert or remove the cable while the power of the controller is on. Failure to observe this precaution may cause malfunction,
overheat, or break.
- Insert or remove the cable straight. Otherwise, the connector part may be damaged or distorted.
- The specifications of this product are subject to change without notice for quality improvement. When using the product continuously,
always check the latest information on Contec website.
- This document must accompany the product upon assigning or transferring.
- No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC.
- All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in
this document, please contact your retailer.
Disclaimer
- We will bear no responsibility for any malfunction or damages from fire, an earthquake, flood, a lightning strike, and other acts of nature,
environmental pollution, abnormal voltage, or incorrect usage.
- We will bear no responsibility if the product is damaged by connecting with inappropriate or not specified equipment.
- The contents of the document have been carefully observed. However, a user might find some details, states, variations are insufficient.
Moreover, the description of setting or usage might not cover any unpredictable issues.
- The information in this document is subject to change without notice or commitment. Regardless of expressed or implied,
we will bear no responsibility for neither the contents of the document nor accuracy, completeness, or sufficiency.
- We will bear no responsibility if the product is not used in accordance with the defined installation, condition and specification, or a user
fails to follow the regulations, the warnings provided in the instructions, manual or the like of the product.
- We will bear no responsibility if the malfunction or damage occurs due to inappropriate handling of the product by user or any part other
than our company (any “third party”), or results from dropping or bumping during transportation and relocation after purchase.
- We will
bear no responsibility if the malfunction or damage occurs due to inappropriate storage or handling, as well as the careless,
negligent or other improper actions by user or any third party.
- We will
bear no responsibility if the malfunction or damage is caused by hardware and/or software which is not the specified product.
- Do not modify the product. We will bear no responsibility for failures or damages caused by remodeling by non-approved engineers.
- Even during the warranty period, the warranty will not apply in this case that regardless of whether a request is made within the warranty
period, we disclaim any indirect or consequential damage (including any opportunity loss, compensation for any business-related damages),
deterioration or loss of data or information, damage to anything other than the product, or any other matters not described in this warranty,
incurred by yourself or your customers, due to any malfunction or defect of the product.
- We disclaim all express and implied warranties to the fullest extent permitted by law. If we cannot disclaim implied warranties under
applicable law, then to the extent possible, such implied warranties are limited to the duration of the express warranty.
- The warranty duration of any replaced or repaired product will be that portion of the warranty period remaining on your original product.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec CPS-CAB-S01 Owner's manual
-
Contec CPS-MG341-ADSC1-931 Reference guide
-
Contec CPS-MC341-A1-111 Reference guide
-
-
-
Contec CPS-SSI-4P Reference guide
-
-
Contec CPS-HBL-8005F Owner's manual
-
-