Zebra 2011 Owner's manual

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

1)Removecenterconsolefasciabyreleasingtheclipsatthe

topfirst.

2)Thenreleasetheclipsatthebottom.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

3)Removethethreeplugsattachingcableloomstothe

console.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

4)Offerupthelefthandsidebracket(032‐02‐0298)and

scribelinestopandbottomasshownontheairventlip.This

materialwillberemovedinstage7toallowclearanceforthe

brackets.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

5)Repeattheprocessoutlinedinstage4fortherighthand

sidebracket(032‐02‐0297).

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

6)Removetheleftandrighthandairventsasshown.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

7)Carefullyremovethematerialbetweenthescribedlinesas

shownbelowonbothairvents.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

8)Replacetheairventsandremovethetwoscrewsretaining

theCDchangerpicturedbelow.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

9)Fitthelefthandsidebracket(032‐02‐0298)asshownusing

oneofthescrewsremovedinstage8.

10)Fittherighthandsidebracket(032‐02‐0297)asshown

usingtheremainingscrewremovedinstage8.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

11)Drilltwo2mm

diameterpilotholesas

shownandfittwoself

tappingscrewsasshown.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

12)Repeattheprocessoutlinedinstage11forthelefthand

sidebracketasshown.

13)Reattachthethreecableloomplugstothecenterconsole

asshown.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

14)Carefullyreplacethecenterconsoleasshown.

NOTE:‐ bendingtheleftandrighthandsidebracketsout

slightlywillassistduringthisstage.Theycanbebentback

inwardsoncethecenterconsoleisfullyinplace

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

15)Fitthefrontbracket(032‐02‐0296)asshownusingfour

shake‐proofwashers(TD503481)andfoursocketbuttonhead

screws(TD503712).

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

16)RotatetheVESAplateontheTilt&RotateAssemblyby

180degreesasshown.

Removethefoursocketheadcapscrews,rotatetheVESA

plateby180degreesandre‐fitthefoursocketheadcap

screws.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

17)FitthedockingstationtotheVESAplateasshown.

NOTE:‐ ensurethelowestsetofholesareusedtoobtainthe

correctheight.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

18)FittheDockingStation/Tilt&

RotateAssemblytothefront

bracketasshownusingthe

providedM8fasteners.

NOTE:‐ Itmaybenecessaryto

temporarilyremovetherubber

edgestriptoallowforcorrect

fitment.

Ensurethatthelocationlugsare

correctlyengagedbeforefinal

tighteningtopreventunwanted

rotation.

For more information, contact your local Motion Reseller or Motion Representative.

www.MotionComputing.com

FordRanger2011+InstallationInstructions

Photographoffinishedinstallation

Zebra 2011 Owner's manual

Related papers

Other documents