Noble House 24303 Operating instructions

Brand
Noble House
Model
24303
Type
Operating instructions

This manual is also suitable for

Page 1 of 5
This bench assimilates the shape of Tree Trunk at the long sides of the bench.
Therefore, the long sides of the bench is irregular in shape and is the intended design.
BENCH
CAUTION: You must read this before you proceed.
Noble House Home Furnishings LLC
Page 2 of 5
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Assemble on a clean non-marring surface (packing foam).
Save all packaging until finished.
No.
Picture
This Bench has multiple parts and may require up to some 15 minutes to assemble. To give you an
overview of the Bench parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions here below to familiarise the parts and steps before assembly.
1
1
13
B
No.
1
Before Beginning Assembly:
Qty
A
Picture
Qty
OVERVIEW
Table (A)
Support Bar (B)
Bench (A)
FRONT VIEW
Bolt
(M8x25mm)
C
D 13
E Spanner Wrench
Noble House Home Furnishings LLC
Page 3 of 5
Step 1
Step 2
Step 3
Attach the Support Bar (B) to the Bench (A)
You may need to apply a little pressure to the Legs - pushing outwards, so as to enable the Support
Bar (B) to be slotted into position.
Using Bolts (C) with Flat Washers (D), tighten the Bolts by using Spanner Wrench(E), as shown in
Pic.1
Loosely tighten the Bolts, up to 80%.
Place the Bench (A) facedown, onto a clean, soft surface to avoid any scratches or damages to the
product.
Lift legs upwards and outwards until the braces are met at position to the base of the bench, as
shown in the above pictures.
Unpack and place all parts on a clean non marring flat surface .
Pic.1
Noble House Home Furnishings LLC
Page 4 of 5
Step 4
Step 5
Secure Legs to Bench by using Bolts (C) and Flat Washers (D) with Spanner Wrench(E) as shown
in Pic.2 at all 8 positions.
Loosely tighten the Bolts, up to 80%. Turn it over and Sit on it.
Then turn it over again, in a sequential manner, gradually tighten each Bolt until all bolts are
evenly secured.
CAUTION: When tightening these screws, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one. This would cause the frame to
warp.
If there is still wobbles, loosen the screws and execute this same drop tests.
WARNING ! IF CHAIR IS NOT STABLE , IT COULD LEAD TO DAMAGING THE PRODUCT.
You are now at the FINAL stage of this assembly.
In a sequential manner, drive in and fully tighten all bolts.
Thereafter, turn the Bench right way up.
The Bench now is ready to be used
Pic.2
Noble House Home Furnishings LLC
Noble House Home Furnishings LLC
Page 5 of 5
Page 1 of 5Page 1 of 5
TABLE
This table assimilates the shape of Tree Trunk at the long sides of the table.
Therefore, the long sides of the table is irregular in shape and is the intended design.
CAUTION: You must read this before you proceed.
Noble House Home Furnishings LLC
Page 2 of 5Page 2 of 5
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Assemble on a clean non-marring surface (packing foam).
Save all packaging until finished.
D
Table Top
( with folded legs )
Description
Support Bar
B
Picture
1
1
A
Description
Picture
C
This Table has multiple parts and may require up to some 15 minutes to assemble. To give you an
overview of the Table parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions here below to familiarise the parts and steps before assembly.
Qty
No.
No.
1
Spanner Wrench
E
Before Beginning Assembly:
13
Washer
(M8.5/16x2mm)
Bolt
(M8x25mm)
Qty
13
OVERVIEW
Support Bar (B)
Table (A)
FRONT VIEW
Noble House Home Furnishings LLC
Page 3 of 5Page 3 of 5
Step 1
Unpack and place all parts on a clean non marring flat surface .
Place the Table (A) facedown, onto a clean, soft surface to avoid any scratches or damages to the
product.
Lift legs upwards and outwards until the braces are met at position to the base of the table, as
shown in the above pictures.
Step 2
Step 3
Attach the Support Bar (B) to the Table (A)
You may need to apply a little pressure to the Legs - pushing outwards, so as to enable the Support
Bar (B) to be slotted into position.
Using Bolts (C) with Flat Washers (D), tighten the Bolts by using Spanner Wrench (E), as shown in
Pic.1
Loosely tighten the Bolts, up to 80%.
Pic.1
Noble House Home Furnishings LLC
Page 4 of 5Page 4 of 5
Step 5
Secure Legs to Table by using Bolts (C) and Flat Washers (D) with Spanner Wrench(E) as shown in
Pic.2 above, at all 8 positions.
Loosely tighten these Bolts, up to 80%.
Turn it over, with assistance from your partner, stand to each of the longside of the table.
EXERT pressure, floorwards, onto the table.
This pressure will help the legs and table top to reach alignment at all joints.
Check for wobbleness.
Turn it over, and in a sequential manner, gradually tighten each Bolt until all bolts are evenly
secured.
CAUTION: When tightening these screws, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one. This would cause the frame to warp.
If there is still wobbles, loosen the screws and execute this same drop tests.
WARNING ! IF TABLE IS NOT STABLE , IT COULD LEAD TO DAMAGING THE PRODUCT.
You are now at the FINAL stage of this assembly.
In a sequential manner, drive in and fully tighten all bolts.
Thereafter, turn the Table right way up.
The Table now is ready to be used
Step 4
Pic.2
Noble House Home Furnishings LLC
Page 5 of 5
OUTDOOR
Noble House Home Furnishings LLC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Noble House 24303 Operating instructions

Brand
Noble House
Model
24303
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents