W10343076B
IT'S TIME TO RETHINK THE GARAGE.
®
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
LE GARAGE REPENSÉ.™
STEEL
MODULAR GEARBOX
FULL-DOOR CABINET
Assembly Instructions
ARMARIO MODULAR DE ACERO PARA HERRAMIENTAS,
PARA PARED - PUERTA COMPLETA
Instrucciones de ensamblaje
ARMOIRE À OUTILS MODULAIRE EN ACIER - PORTE PLEINE
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
CABINET/LOCKER SAFETY ........................ 2
PARTS ........................................................... 3
ASSEMBLY INSTRUCTIONS........................ 3
ACCESSORIES .............................................. 5
WARRANTY ................................................... 6
SEGURIDAD DEL ARMARIO .......................7
PIEZAS ...........................................................8
INSTRUCCIONES DE ENSAMBLAJE ..........8
ACCESORIOS.............................................. 10
GARANTÍA .................................................. 11
SÉCURITÉ DE L’ARMOIRE.........................12
PIÈCES .........................................................13
INSTRUCTIONS D'ASSEMBLAGE .............13
ACCESSOIRES.............................................15
GARANTIE ....................................................16
2
CABINET/LOCKER SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
3
PARTS
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
■ Intended for use in a garage.
■ Maximum weight limit is 45 lbs (20 kg) for each shelf.
■ Maximum weight limit is 300 lbs (136 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include a hex key
wrench, a key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
P3
P7
P2
P4
P5
P6
P10
P8m
P8
P9
P1
F1 F2 F3c F5
4
Assemble Cabinet
Gather the required tools before starting installation.
Tools Needed:
Tools Supplied:
IMPORTANT:
■ Two people may be required to complete the assembly.
■ As you assemble the cabinet, make sure the edges with the
holes are facing up.
■ If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
six internal hex head bolts (F1) and two ⁵⁄₁₆"
flange nuts (F2) for
the two middle holes only, as shown. Do not tighten completely.
4. Position side panel (P3) so that the top (P2) is between the edges
of side panel (P3).
5. Align the holes and attach the top (P2) to the side (P3) using six
internal hex head bolts (F1) and two ⁵⁄₁₆"
flange nuts (F2) for the
two middle holes only, as shown. Do not tighten completely.
6. Insert cabinet bottom (P4) between the edges of side panels
(P1 and P3).
NOTE: Make sure the edges with the holes are facing up.
7. Align the holes and attach the bottom (P4) to the side panels
(P1 and P3) using six hex-head bolts (F1) and two ⁵⁄₁₆"
flange
nuts (F2) for the two middle holes only, for each side as shown.
Do not tighten completely.
Attach Back Panels
1. Align lower back panel (P6) with the holes in the cabinet
bottom (P4). Using Phillips-head screws (F3c), attach back panel
(P6) to the bottom (P4) and sides (P1 and P3) as shown. Do not
tighten screws completely.
2. Align upper back panel (P5) with the holes in the cabinet top (P2).
Using Phillips-head screws (F3c), attach back panel (P5) to the
top (P2) and sides (P1 and P3) as shown. Do not tighten screws
completely.
NOTE: Upper back panel (P5) will slightly overlap lower back
panel (P6).
3. Using Phillips-head screws (F3c), attach the upper back panel
(P5) to the lower back panel (P6) as shown.
4. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle, and bottom.
5. Using the hex key (provided), completely tighten all the cabinet
bolts and nuts.
F1 F2
F1
⁵⁄₁₆
" Internal hex head bolt (24)
F2
⁵⁄₁₆
"Flange nut (8)
■ ¹⁄₂" Wrench
■ ³⁄₈" Wrench
■ ¹¹⁄₃₂" Wrench
■ Phillips screwdriver
■ Pliers
■ Level
■ Hex key ■ Key
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet.
Failure to do so can result in back or other injury.
F3c
F3c Phillips-head screw (16 - black)
P2
P1
P3
P4
P3
P2
P1
P4
P6
P5
P2
P3
5
Install Leveling Legs or Casters
The Gladiator
®
Modular Cabinet is designed to be either stationary or
to roll on casters. See “Assessories” to order the caster kit.
IMPORTANT: If you decide to install the casters on the cabinet, see
the installation instructions included with the caster kit (provided).
To install leveling legs:
1. Place the cabinet on its side.
2. Screw a leveling leg (P7) into each of the four rivet nuts located at
the corners of the cabinet as shown.
3. Stand the cabinet upright.
4. If you have not already, fasten the two bolts at each front corner,
of the cabinet frame. Completely tighten all the cabinet bolts and
nuts.
Install Shelves
IMPORTANT:
■ Install shelf (P8m) in the cabinet so that the long edge with
magnets is facing the cabinet front.
■ Use the pair of holes indicated to install shelf (P8m), so the doors
will lock.
■ Shelf (P8) may be installed using any of the other pairs of holes in
the cabinet sides.
1. Align the holes in the shelf with the pair of holes shown.
2. Using Phillips-head screws (F3c) and small flange nuts (F5) per
side, fasten shelf (P8m) to the cabinet sides (P1 and P3).
3. Place shelf (P8) so that the holes in the ends are aligned with the
desired set of holes in the cabinet sides (P1 and P3).
4. Using Phillips-head screws (F3c) and small flange nuts (F5) per
side, fasten the shelf to the cabinet sides (P1 and P3).
Install Doors
The door hinges are designed with keyhole slots at the top and
bottom so the door will hang on the cabinet while you are fastening
the screws.
1. Start Phillips-head screws (F3c) in both the top and bottom holes
on each side of the cabinet.
2. Hang the right-hand side door (P10) from the top and bottom
screws, and hand tighten.
3. Insert the middle two screws through the door hinge into the
cabinet and hand tighten.
4. Repeat steps 2 and 3 to attach the left-hand door (P9).
5. Align the doors and completely tighten the screws.
Complete the Assembly
1. Make sure there is a bolt or screw in each hole of the cabinet
frame.
2. Move the cabinet to its final location.
3. If the doors are not aligned, loosen all the screws attaching the
door hinge to the cabinet.
4. Adjust door to the desired height, and fully tighten the screws.
ACCESSORIES
To order the accessories listed below or to inquire about other
available accessories call 1-866-342-4089 or contact your
authorized Gladiator brand dealer.
In Canada, call 1-800-807-6777.
Caster Kit
Order Part # GACK04KDSX
VersaTop™ Work Surface
Order Part # GAVT18SPSX
Modular Bamboo Top
Order Part # GAAC28BAYX
A. Leveling legs
F3c F5
F3c Phillips-head screw (8 - black) F5 Small flange nut (8)
A. Holes for installing shelf
B. Slot in shelf for lock
A
P7
P4
P1
P6
B
A
P1
P8m
P2
P3
F3c
F3c Phillips-head screw (8 - black)
A. Phillips-head screws (F3c)
A
P2
P4
P8
P9
P8m
6
GLADIATOR
®
GARAGEWORKS
STEEL MODULAR GEARBOX CABINET WARRANTY
TEN YEAR LIMITED WARRANTY - (GEARBOX ONLY - LABOR NOT INCLUDED)
For ten years from the original date of purchase, when the Steel Modular GearBox Cabinet is installed, used and maintained according
to the instructions attached to or furnished with the product, Gladiator
®
GarageWorks will, at its sole option, provide factory specified
replacement parts to correct defects in materials or workmanship that existed when the product was purchased or replace the product
(excludes shipping or freight fees). If replaced, your product will be covered by the remaining ten-year limited warranty of the original
unit.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THE LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AT
OUR DISCRETION AS PROVIDED HEREIN. This limited warranty is valid in the United States and Canada and applies only when the
product is used in the country in which it was purchased. This limited warranty is effective from the date of the original consumer
purchase. Proof of original purchase date is required to obtain service or replacement under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. In-home service including, but not limited to, service calls to correct the installation of any Gladiator
®
GarageWorks products or to
instruct you on how to use or install them.
2. Damage resulting from improper handling or shipping of products, or products damaged by accident, alteration, misuse, abuse, fire,
flood, improper installation, acts of God, neglect, corrosion, modification or mishandling.
3. All travel, transportation, shipping or freight fees to deliver replacement products or to return defective products.
4. Factory specified replacement parts or product replacement when your product is used in other than normal, single-family
household use, such as a commercial environment or handled in a manner contrary to published user or operator instructions and/
or installation instructions.
5. Cosmetic damage including scratches, dings, dents or cracks that do not affect the structural or functional capability of the
product.
6. Any labor costs during the limited warranty period.
7. Damage resulting from improper loading beyond the specified maximum weight capacity outlined in the assembly instructions
provided with the product, including overloading of hooks, baskets, shelves, cabinets, and other Gladiator
®
GarageWorks
accessories used with the product.
8. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.
9. Replacement keys or locking mechanism.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
GLADIATOR
®
GARAGEWORKS SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and
provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not
apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province
to province.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Gladiator
®
GarageWorks dealer to
determine if another warranty applies.
If you need service, call the Gladiator
®
GarageWorks Customer eXperience Center, 1-866-342-4089 (toll-free), from anywhere in the
U.S.A. In Canada, contact your Whirlpool Canada LP designated service company or call 1-800-807-6777.
In the United States, Gladiator
®
GarageWorks means Whirlpool Corporation, Benton Harbor, Michigan 49022. In Canada, Gladiator
®
GarageWorks means Whirlpool Canada LP, Mississauga, ON L5N 3A7. 9/11
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your Steel Modular
GearBox Cabinet to better help you obtain assistance or service
if you ever need it. You will need to know your complete model
number and serial number. You can find this information on the
model and serial label located on the back of the product.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Gladiator GAAC68PSDG User manual
-
Gladiator W11685170A User manual
-
Gladiator GAPK24A4FG Installation guide
-
-
-
-
-
-
-
Other documents
-
Whirlpool GACP15XXMG Warranty (59.89 KB)
-
-
-
Igloo FR329 Operating Instructions Manual
-
Ryobi STM405 Owner's manual
-
Gladiator Garageworks 2253351A User manual
-
Gladiator Garageworks 2253694A User manual
-
-
-
