Ohlins HR609 Mounting Instruction

Category
Car kits
Type
Mounting Instruction
Shock Absorber for HONDA CBR250R HRC
HR 609
Mounting Instructions
Note!
Please note that this image is a general representation
of the product and may differ slightly from your product.
Note!
Please note that during storage and transportation,
especially at high ambient temperature, some of the oil
and grease used for assembling may leak and stain the
packaging. This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Warning!
Before installing this product, read the Öhlins Owner’s
Manual. The shock absorber is an important part of your
vehicle and will affect the stability.
Kit Contents
Description Part No Pcs
Shock absorber HR 609 1
Sticker "ÖHLINS" 01185-04 2
Sticker "ÖHLINS" 01185-01 2
Sticker "ÖHLINS" 00192-01 2
C-spanner S36 60710-01 2
Owners manual 07241-02 1
Alternative components
Spring 46/165/100 N/mm 60292-34 1
Spring 46/165/110 N/mm 60292-39 1
Note!
Before installing this product, check the contents of the
kit. If anything is missing, please check an Öhlins dealer.
2
MOUNTING INSTRUCTIONS
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground. Make
sure the motorcycle is in a stable position.
2
Remove the passenger seat by unlocking it with
ignition key then remove the rider seat by
loosening the screws (1),(2)
Warning!
It is advisable to have an Öhlins dealer install the shock
absorber.
Warning!
If working on a raised vehicle, ensure it is securely
supported so that it will not tip over.
Note!
Before mounting this product clean the vehicle
thoroughly.
Note!
When working on this product, always see the Vehicle
Service Manual for vehicle specic procedures and
important data.
1
2
3
MOUNTING INSTRUCTIONS
3
3
Partially dismount rear side cover by loosening
the screws (1), (2)
4
Partially dismount middle cover by loosening
the bolts (1), (2), (3)
1
1
2
2
4
MOUNTING INSTRUCTIONS
5
Remove LH/RH front upper cover by loosening
the plastic clip (1) and the bolt (2) for each
side, then take fuel tank cover off in order to
gain access to fuel tank mounting bolts.
6
Remove fuel tank by loosening mounting bolts
(1) Front x1
(2) Rear x2
1
2
2
1
5
MOUNTING INSTRUCTIONS
7
Loosen 4 bolts (two each side) of airbox in
order to have more space when removing upper
shock absorber mounting point.
8
Remove upper and lower mounting shock bolts
according to the diagram while slightly lifting
airbox.
1
2
6
MOUNTING INSTRUCTIONS
9
Remove original shock absorber, then replace
with Ohlins product
Tighten the mouting bolts at the torque value
as specied in the vehicle service manual and
reverse all procedures.
Note!
Lower the vehicle so that the suspension is slightly
compressed before tightening the screws.
Caution!
Ensure that all screws are tightened to the correct
torque and that nothing fouls or restricts movement
of the shock absorber when the suspension is fully
compressed or extended.
Öhlins Asia Co. Ltd
700/937 Moo5, Tambol Nongkhaga,
Amphur Phantong, Chonburi Province
20160 Thailand
© Öhlins Asia Co. Ltd. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SET-UP DATA
Warning!
Before riding, always make sure that the basic settings
made by Öhlins are according to recommended
Set-up Data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make any
adjustments. Contact an Öhlins dealer if you have any
questions about setting up.
ADJUSTMENTS
Part no. MI_HR609_EN_0
Issued 2017-01-09
Recommended set-up
Spring Preload............. 7 mm.
Rebound adjuster ........ 10 Clicks
Spring
Part No ........................ 60292-36
Free spring length......... 165 mm.
Spring rate.................... 105 N/mm
Preload adj.range......... [ 0-14] mm
Shock absorber data
Length ............................. 298 mm.
Stroke .............................. 54 mm.
Spring Preload
Adjuster
Rebound
Adjuster
Recommended spring
Spring part No. Spring rate
Preload adj.range
60292-34 100 N/mm [ 0-14] mm
60292-39 110 N/mm [ 0-14] mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Ohlins HR609 Mounting Instruction

Category
Car kits
Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI