Dell XPS 15 9575 2-in-1 User manual

Brand: Dell

Model: XPS 15 9575 2-in-1

Category: Notebooks

Type: User manual

XPS 15 2-in-1

Service Manual

Regulatory Model: P73F

Regulatory Type: P73F001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

subsidiaries. Other trademarks may be trademarks of their respective owners.

2020 - 03

Rev. A03

1 Before working inside your computer............................................................................................. 7

Before you begin ...................................................................................................................................................................7

Safety instructions.................................................................................................................................................................7

Recommended tools..............................................................................................................................................................7

Screw list................................................................................................................................................................................ 8

2 After working inside your computer............................................................................................... 9

3 Removing the base cover.............................................................................................................10

Procedure..............................................................................................................................................................................10

4 Replacing the base cover............................................................................................................. 13

Procedure..............................................................................................................................................................................13

5 Removing the solid-state drive.................................................................................................... 15

Prerequisites......................................................................................................................................................................... 15

Procedure..............................................................................................................................................................................15

6 Replacing the solid-state drive.....................................................................................................16

Procedure..............................................................................................................................................................................16

Post-requisites......................................................................................................................................................................16

7 Removing the I/O-board interposers.............................................................................................17

Prerequisites......................................................................................................................................................................... 17

Procedure..............................................................................................................................................................................17

8 Replacing the I/O-board interposers............................................................................................ 19

Procedure .............................................................................................................................................................................19

Post-requisites.....................................................................................................................................................................20

9 Removing the heat sink............................................................................................................... 21

Prerequisites......................................................................................................................................................................... 21

Procedure..............................................................................................................................................................................21

10 Replacing the heat sink..............................................................................................................23

Procedure............................................................................................................................................................................. 23

Post-requisites.....................................................................................................................................................................24

11 Removing the fans.....................................................................................................................25

Prerequisites........................................................................................................................................................................ 25

Procedure.............................................................................................................................................................................25

12 Replacing the fans.................................................................................................................... 26

Contents

Contents 3

Procedure.............................................................................................................................................................................26

Post-requisites.....................................................................................................................................................................26

13 Removing the battery................................................................................................................ 27

Lithium-ion battery precautions.........................................................................................................................................27

Prerequisites.........................................................................................................................................................................27

Procedure............................................................................................................................................................................. 27

14 Replacing the battery................................................................................................................ 29

Procedure.............................................................................................................................................................................29

Post-requisites.....................................................................................................................................................................29

15 Removing the I/O board............................................................................................................ 30

Prerequisites........................................................................................................................................................................ 30

Procedure.............................................................................................................................................................................30

16 Replacing the I/O board.............................................................................................................32

Procedure............................................................................................................................................................................. 32

Post-requisites.....................................................................................................................................................................33

17 Removing the speakers..............................................................................................................34

Prerequisites.........................................................................................................................................................................34

Procedure............................................................................................................................................................................. 34

18 Replacing the speakers..............................................................................................................35

Procedure.............................................................................................................................................................................35

Post-requisites.....................................................................................................................................................................35

19 Removing the coin-cell battery...................................................................................................36

Prerequisites........................................................................................................................................................................ 36

Procedure.............................................................................................................................................................................36

20 Replacing the coin-cell battery.................................................................................................. 37

Procedure............................................................................................................................................................................. 37

Post-requisites..................................................................................................................................................................... 37

21 Removing the power button with fingerprint reader.....................................................................38

Prerequisites.........................................................................................................................................................................38

Procedure............................................................................................................................................................................. 38

22 Replacing the power button with fingerprint reader.................................................................... 39

Procedure.............................................................................................................................................................................39

Post-requisites.....................................................................................................................................................................39

23 Removing the display assembly..................................................................................................40

Prerequisites........................................................................................................................................................................ 40

Procedure.............................................................................................................................................................................40

Contents

24 Replacing the display assembly..................................................................................................42

Procedure............................................................................................................................................................................. 42

Post-requisites.....................................................................................................................................................................43

25 Removing the system board...................................................................................................... 44

Prerequisites.........................................................................................................................................................................44

Procedure............................................................................................................................................................................. 44

26 Replacing the system board...................................................................................................... 46

Procedure.............................................................................................................................................................................46

Post-requisites..................................................................................................................................................................... 47

Entering the Service Tag in the BIOS setup program.................................................................................................... 47

27 Removing the palm-rest and keyboard assembly......................................................................... 48

Prerequisites.........................................................................................................................................................................48

Procedure............................................................................................................................................................................. 48

28 Replacing the palm-rest and keyboard assembly......................................................................... 49

Procedure.............................................................................................................................................................................49

Post-requisites.....................................................................................................................................................................49

29 Downloading drivers................................................................................................................. 50

Downloading the audio driver............................................................................................................................................ 50

Downloading the graphics driver.......................................................................................................................................50

Downloading the USB 3.0 driver........................................................................................................................................51

Downloading the Wi-Fi driver............................................................................................................................................. 51

Downloading the media-card reader driver......................................................................................................................52

Downloading the fingerprint reader driver....................................................................................................................... 52

Downloading the chipset driver.........................................................................................................................................53

Downloading the network driver....................................................................................................................................... 53

30 System setup...........................................................................................................................55

Boot Sequence.................................................................................................................................................................... 55

Navigation keys................................................................................................................................................................... 55

System setup....................................................................................................................................................................... 55

Entering BIOS setup program............................................................................................................................................56

Enabling or disabling the USB in BIOS setup program............................................................................................. 56

Identifying the storage drive in BIOS setup program................................................................................................56

Checking the system memory in BIOS setup program.............................................................................................56

System setup options......................................................................................................................................................... 56

31 System and setup password.......................................................................................................62

Assigning a system setup password................................................................................................................................. 62

Deleting or changing an existing system setup password............................................................................................. 62

Clearing CMOS settings..................................................................................................................................................... 63

Clearing BIOS (System Setup) and System passwords.................................................................................................63

Contents

32 Troubleshooting....................................................................................................................... 64

Flashing the BIOS................................................................................................................................................................ 64

Reinstall Windows using a USB recovery drive............................................................................................................... 64

Flashing BIOS (USB key)....................................................................................................................................................64

Fixing a no-boot issue caused by USB-boot support..................................................................................................... 65

Enhanced Pre-Boot System Assessment (ePSA) diagnostics......................................................................................65

Running the ePSA diagnostics.....................................................................................................................................65

System diagnostic lights.....................................................................................................................................................66

Flea power release...............................................................................................................................................................66

WiFi power cycle..................................................................................................................................................................67

33 Getting help and contacting Dell................................................................................................ 68

6 Contents

Before working inside your computer

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Before you begin

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click Start >

Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.

4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

5. Remove any media card and optical disc from your computer, if applicable.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise

noted, each procedure included in this document assumes that you have read the safety information that shipped with your computer.

NOTE:

Before working inside your computer, read the safety information that shipped with your computer. For more

safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the electrical outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat and clean.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by

its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety

instructions that shipped with the product or at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

CAUTION: When you disconnect a cable, pull on its connector or on its pull tab, not on the cable itself. Some cables have

connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When

disconnecting cables, keep them evenly aligned to avoid bending any connector pins. When connecting cables, ensure

that the ports and connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Recommended tools

The procedures in this document may require the following tools:

• Phillips #00 and #01 screwdriver

Before working inside your computer 7

• Torx #5 (T5) screwdriver

• Plastic scribe

Screw list

The following table provides the list of screws that are used for securing different components.

Table 1. Screw list

Component Secured to Screw type Quantity Screw image

Base cover Palm-rest and keyboard

assembly

Torx head M2x3 8

Battery Palm-rest and keyboard

assembly

M2x5 8

Display assembly Palm-rest and keyboard

assembly

M2.5x4 6

Display-cable bracket System board M1.6x1.8 2

Fans Palm-rest and keyboard

assembly

M2x3 4

Fingerprint-reader Palm-rest and keyboard

assembly

M1.6x1.8 1

Heat sink System board M2x3 5

I/O board Palm-rest and keyboard

assembly

M2x3 1

I/O-board interposer

Palm-rest and keyboard

assembly

M1.6x5.5 4

Power button Palm-rest and keyboard

assembly

M2x1.7 1

Speakers Palm-rest and keyboard

assembly

M2x1.7 2

Solid-state drive System board M2x3 1

System board Palm-rest and keyboard

assembly

M2x3 2

USB Type-C bracket I/O board M2x4 3

Type-C USB bracket System board M2x4 3

Wireless-antenna

bracket

System board M2x4 2

8 Before working inside your computer

After working inside your computer

CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.

1. Replace all screws and ensure that no stray screws remain inside your computer.

2. Connect any external devices, peripherals, or cables you removed before working on your computer.

3. Replace any media cards, discs, or any other parts that you removed before working on your computer.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

After working inside your computer 9

Removing the base cover

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

Procedure

1. Remove the eight torx head screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.

2. Using a plastic scribe, pry the base cover from the right corner of the palm-rest and keyboard assembly.

NOTE:

Do not begin to pry the base cover from top edge (next to hinges), as this may break the plastic clips and lead

to cosmetic damage.

3. Pry the base cover starting from the right side of palm-rest and keyboard assembly.

4. Pry the base cover from the bottom left corner of the palm-rest and keyboard assembly.

5. Pry the base cover from the left side of the palm-rest and keyboard assembly.

10 Removing the base cover

6. Move the base cover from left to right and lift the base cover from the palm-rest and keyboard assembly.

7. Turn-off the battery switch.

Removing the base cover

NOTE: Turn-off the battery switch before you proceed to remove any other component from your computer.

12 Removing the base cover

Replacing the base cover

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

Procedure

1. Turn-on the battery switch, If was turned off earlier.

2. Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly.

Replacing the base cover 13

3. Snap the base cover into the tabs on the palm-rest and keyboard assembly.

4. Replace the eight torx head screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.

14 Replacing the base cover

Removing the solid-state drive

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

CAUTION: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

Prerequisites

Remove the base cover.

Procedure

1. Peel and remove the thermal pad from the solid-state drive.

2. Remove the screw (M2x3) that secures the solid-state drive to the system board.

3. Lift the solid-state drive at an angle, then slide and remove the solid-state drive from the solid-state drive slot.

Removing the solid-state drive 15

Replacing the solid-state drive

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

Procedure

1. Align the notch on the solid-state drive with the tab on the solid-state drive slot.

2. At an angle, slide the solid-state drive into the solid-state drive slot.

3. Replace the screw (M2x3) that secures the solid-state drive to the system board.

4. Adhere the thermal pad on the solid-state drive.

Post-requisites

Replace the base cover.

16 Replacing the solid-state drive

Removing the I/O-board interposers

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

Prerequisites

Remove the base cover.

Procedure

1. Remove the four screws (M1.6x5.5) that secure the I/O-board cable to the system board.

2. Peel and remove the I/O-board cable from the fans.

3. Remove the two I/O-board interposers from the system board.

NOTE:

Remove the I/O-board interposers immediately after removing the I/O-board cable to prevent the interposers

from falling out of your computer. The pins on the interposer boards are very fragile. Avoid contact with the pins or

bottom of the boards, instead handle the boards by lifting and holding from the edges or side. After removing the

interposer boards from the system, place them on an ESD mat in a location where contact and movement can be

avoided. DO NOT push or apply pressure to the pins on the interposer boards and DO NOT use any motion that may

scratch the pins, such as rotating/turning the boards while they are in contact with any surface.

Removing the I/O-board interposers 17

18 Removing the I/O-board interposers

Replacing the I/O-board interposers

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in Before working inside your computer. After working inside your computer, follow the instructions in After

working inside your computer. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance.

Procedure

1. Using the alignment posts, place the two I/O-board interposers on the system board.

2. Align the screw holes on the I/O-board cable with the screw holes on the I/O-board interposers and adhere the I/O-board cable to

the fans.

NOTE:

When installing the I/O board cable, align and connect the I/O board end to the I/O board side and the system

board end to the system board side.

CAUTION: Wrong alignment of the cable might cause damage to the connectors.

3. Replace the four screws (M1.6x5.5) that secure the I/O-board cable to the system board.

Replacing the I/O-board interposers 19

Post-requisites

Replace the base cover.

Replacing the I/O-board interposers

Page is loading ...

Dell XPS 15 9575 2-in-1 User manual

Brand: Dell

Model: XPS 15 9575 2-in-1

Category: Notebooks

Type: User manual

Download PDF

report

Dell XPS 15 9575 2-in-1 User manual

Dell XPS 15 9575 2-in-1 User manual

Related papers

Other documents