Lifetime 90469 Owner's manual

Brand: Lifetime

Model: 90469

Type: Owner's manual

MODEL N° 90469

OWNER’S MANUAL

COPY

INSTRUCTION #1141504 E 7/22/2016

COPY

Electric Drill

Phillips Screwdriver

(1)

Funnel

(1)

Wood Block

(1)

Cement Mix

(9 Bags, 80 lb each)

(30”)

Rebar

Rubber Mallet

(1)

Water Hose

(1)

9/16” Wrench

(2)

Ladder

(3)

(1)

Tape Measure

(1)

Shovel

Level

(1)

3/4” Socket Wrench

(2)

7/16” Socket Wrench

(2)

1/2” Socket Wrench

(2)

9/16” Socket Wrench

(2)

PARTS LIST

HARDWARE LIST

ID Item Description Qty

ALH Top Pole 1

ALF Middle Pole 1

ALE Bottom Pole 1

BGO Upper Extension Arm 2

BGP Lower Extension Arm 2

ALS Rear Lifter Arm 2

AKF Gas Spring 1

AKG Gas Spring Cover 1

ALX Rim 1

AJI Backboard 1

CKH Handle Top 1

CKI Handle Bottom 1

CKJ Handle Frame 1

BAA Left Frame Pad 1

BAB Right Frame Pad 1

AJQ Center Frame Pad 2

BGR U-Bolt Washer Plate 1

ALD Plastic Guard 1

AKZ Net 1

AMA Rim Cover Plate 1

APY Rim Pivot Bracket 1

AOW Spring Retainer Plate 1

ALL Pole Bracket 1

BLC Tie Plate 1

CKM Pump Adjust Link 2

CKG Link Cap 2

ALM Pole Cap 1

CMR Pump Adjust Actuator 2

AQC Extension Arm Caps 2

AKP Height Sticker 1

AMT Warning Sticker (applied to Middle Pole) 1

BGW Alignment Frame (image not shown) 1

ID Item Description Qty

BCO Pole Assembly Hardware

ANF 3/8” x 5” Hex Bolt 2

ANE 1/2” x 3.91” Spacer 2

AAF 3/8” Washer 2

AAA 3/8” Nylock Nut 2

CMV #10 x .62” Self-Drilling Screw 2

HARDWARE LIST

ID Item Description Qty

BCS Backboard to Rim Assembly Hardware

EAP 5/16” x 1” Carriage Bolt 2

AAQ 3/8” Push Nut 2

ABK 5/16” Nylock Flange Nut 4

AAV 5/16” Jam Nut 2

ADR #7 x 3/8” Screw 4

AJW Compression Spring 2

APZ 4” U-Bolt 1

ABQ 3/8” x 5 1/2” Axle 1

BCR Backboard to Pole Assembly Hardware

AQB 5/16” x 3/4” Thread-Cutting Bolt 2

ANZ 1/2” x 1/5” Spacer 2

AAX 1/2” Centerlock Nut 4

ANK 1/2” Nylon Washer 4

ABP 1/2” x 3/8” Poly Spacer 2

AOR 1/2” Washer 6

ANP 1/2” x 3/4” Coupler 1

AQD 1/2” x 5” Hex Bolt 1

ANQ 1/2” x 3” Bolt with Nylon Patch 2

ANU 1/2” x 1 3/4” Hex Bolt 2

AAD 1/2” x 7 1/16” Hex Bolt 1

ABN 1/2” x 1/8” Plastic Washer 4

ANS 1/2” Nylon Plug 4

BCT Handle Assembly Hardware

AAD 1/2” x 7 1/16” Hex Bolt 1

AOR 1/2” Washer 2

AAX 1/2” Centerlock Nut 3

ADT #6 x 5/8” Screw 7

ABB 3/8” Centerlock Nut 1

CHQ 3/8” x 1” Hex Bolt 1

CKV 3/8” Clear Plastic Washer 2

CKU 1/2” x .69” Black Poly Spacer 2

ACX 5/16” x 2 1/2” Hex Bolt 1

CKW 3/8” x 6” Hex Bolt 1

CKX .63” x 2 1/2” Spacer 2

AAW 1/2” x 6 1/2” Hex Bolt 2

CKY 1/2” x 1.15” Black Poly Spacer 2

CKZ Gas Shock Rod 1

ANZ 1/2” x 1/5” Spacer 3

AAO 5/16” Nylock Nut 1

AEB 1/4” Washer 2

BFI 3/8” Nylock Jam Nut 1

ABN 1/2” x 1/8” Plastic Washer 4

Parts shown at 10% of Actual Size

PARTS IDENTIFIER

BGP (x2)

Lower Extension Arm

BGO (x2)

Upper Extension Arm

ALS (x2)

Rear Lifter Arm

31”

ALH (x1)

Top Pole

ALF (x1)

Middle Pole

ALE (x1)

Bottom Pole

CKJ (x1)

Handle Frame

CKH (x1)

Handle Top

CKI (x1)

Handle Bottom

HARDWARE LIST

ID Item Description Qty

BCT Handle Assembly Hardware, Continued

ANK 1/2” Nylon Washer 2

AAB 1/4” Centerlock Nut 2

CKT .69” x 3-1/2” Poly Spacer 1

AKH Grease Packet 1

BCU Frame Pad Assembly Hardware

ADP #10 x 7/8” Self-Drilling Flat Screw 10

AKZ (x1)

Net

ALX (x1)

Rim

AJI (x1)

Backboard

Part shown at 5% of Actual Size

Parts shown at 10% of Actual Size

PARTS IDENTIFIER

AKF (x1)

Gas Spring

AKG (x1)

Gas Spring Cover

BAB (x1)

Right Frame Pad

BAA (x1)

Left Frame Pad

AJQ (x2)

Center Frame Pad

Parts shown at 25% of Actual Size

PARTS IDENTIFIER

ALM (x1)

Pole Cap

ALL (x1)

Pole Bracket

BLC (x1)

Tie Plate

AKP (x1)

Height Sticker

CMR (x2)

Pump Adjust Actuator

CKG (x2)

Link Cap

AQC (x2)

Extension Arm Cap

ALD (x1)

Plastic Guard

AMA (x1)

Rim Cover Plate

BGR (x1)

U-Bolt Washer Plate

CKM (x2)

Pump Adjust Link

Parts shown at Actual Size

AOW (x1)

Spring Retainer Plate

APY (x1)

Rim Pivot Bracket

HARDWARE IDENTIFIER

POLE ASSEMBLY HARDWARE [BCO]

Hardware shown at Actual Size

BACKBOARD TO RIM ASSEMBLY HARDWARE [BCS]

Hardware shown at Actual Size

CMV (x2)*

#10 x .62” Self-Drilling

Screw

AAA (x2)

3/8” Nylock Nut

AAF (x2)

3/8” Washer

ANF (x2)

3/8” x 5” Hex Bolt

ANE (x2)

1/2” x 3.91” Spacer

*Note: Only one #10 x .62” Self-Drilling

Screw (CMV) will be used in Section 1.

Save the second Screw for use in Section 5.

5”

(Not actual length)

EAP (x2)

5/16” x 1” Carriage Bolt

AAQ (x2)

3/8” Push Nut

ABK (x4)

5/16” Nylock Flange Nut

AAV (x2)

5/16”Jam Nut

ADR (x4)

#7 x 3/8” Screw

Hardware shown at 25% of Actual Size

AJW (x2)

Compression Spring

APZ (x1)

4” U-Bolt

ABQ (x1)

3/8” x 5 1/2” Axle

HARDWARE IDENTIFIER

AAD (x1)

1/2” x 7 1/16” Hex Bolt

(Not actual length)

AAX (x4)

1/2” Centerlock Nut

BACKBOARD TO POLE ASSEMBLY HARDWARE [BCR]

Hardware shown at Actual Size

AQB (x2)

5/16” x 3/4”

Thread-Cutting Bolt

ABP (x2)

1/2” x 3/8” Poly Spacer

AOR (x6)

1/2” Washer

ANK (x4)

1/2” Nylon Washer

AQD (x1)

1/2” x 5” Hex Bolt

5”

(Not actual length)

ANQ (x2)

1/2” x 3” Bolt with Nylon Patch

ANZ (x2)

1/2” x 1/5” Spacer

ABN (x4)

1/2” x 1/8” Plastic Washer

ANS (x4)

1/2” Nylon Plug

ANP (x1)

1/2” x 1 3/4” Nut Coupler

ANU (x2)

1/2” x 1 3/4” Hex Bolt

7 1/16”

HARDWARE IDENTIFIER

HANDLE ASSEMBLY HARDWARE [BCT]

Hardware shown at Actual Size

ACX (x1)

5/16” x 2 1/2” Hex Bolt

BFI (x1)

3/8” Nylock Jam Nut

CKT (x1)

.69” x 3 1/2” Poly Spacer

CKU (x2)

.69” x 3/4”

Poly Spacer

CHQ (x1)

3/8” x 1” Hex Bolt

AEB (x2)

1/4” Flat Washer

ABN (x4)

1/2” x 1/8” Plastic Washer

ANK (x2)

1/2” Nylon

Washer

CKX (x2)

.63” x 2 1/2” Spacer

CKY (x2)

1/2” x 1.15” Black Poly Spacer

CKZ (x1)

Gas Shock Rod

6”

(Not actual length)

CKW (x1)

3/8” x 6” Hex Bolt

(Not actual length)

AAD (x1)

1/2” x 7 1/16” Hex Bolt

AOR (x2)

1/2” Flat Washer

7 1/16”

HARDWARE IDENTIFIER

HANDLE ASSEMBLY HARDWARE (CONTINUED)

Hardware shown at Actual Size

AAX (x3)

1/2” Centerlock Nut

AAO (x1)

5/16” Nylock Nut

ABB (x1)

3/8” Centerlock Nut

AAW (x2)

1/2” x 6 1/2” Hex Bolt

(Not actual length)

ANZ (x3)

1/2” x 1/5” Spacer

AAB (x2)

1/4” Centerlock Nut

CKV (x2)

3/8” Plastic Washer

ADT (x7)

#6 x 5/8” Screw

ADP (x10)

#10 x 7/8” Self-Drilling Flat Screw

FRAME PAD ASSEMBLY HARDWARE [BCU]

Hardware shown at Actual Size

AKH (x1)

Grease Packet

6 1/2”

POLE ASSEMBLY

HARDWARE REQUIRED

SEC

Hardware shown at Actual Size

CMV (x2)*

#10 x .62” Self-Drilling

Screw

AAA (x2)

3/8” Nylock Nut

AAF (x2)

3/8” Washer

ANF (x2)

3/8” x 5” Hex Bolt

ANE (x2)

1/2” x 3.91” Spacer

5”

(Not actual length)

Note: Only one #10 x .62” Self-Drilling Screw (CMV) will be used in

Section 1. Save the second Screw for use in Section 5.

PARTS REQUIRED

TOOLS REQUIRED

Parts shown at 10% of Actual Size

Phillips Screwdriver

Wood Block

ALH (x1)

Top Pole

ALF (x1)

Middle Pole

ALE (x1)

Bottom Pole

ALL (x1)

Pole Bracket

Part shown at 25% of Actual Size

9/16” Socket Wrench (x2)

Electric Drill

Warning Sticker

POLE ASSEMBLY

SEC

30” Rebar

Shovel

Tape Measure

Cement Mix

Level

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

Dig a round hole 24” deep and 21” in diameter. If you live in an area

where frost heaves may pose a problem, consult your local building

inspector to determine the proper hole depth. The edge of the hole

should be ﬂ ush with the edge of the playing surface.

SEC

1.1

Note: A Ground Sleeve is available as an alternative to cementing

the Pole into the ground. Please contact Customer Service for

more information.

NO HARDWARE REQUIRED FOR THIS PAGE

Mix 8 1/2 bags of concrete. Save 1/2 bag of concrete mix to use

later in the assembly. Pour the mixed concrete into the hole until it is

ﬁ lled to the level of the playing surface.

(9 Bags, 80 lb each)

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

ALE

16”

Make a mark 16 inches from the dimpled end of the Bottom Pole (ALE)

(do not scratch the powder coating). Slide the Alignment Frame (BGW)

over the Bottom Pole.

SEC

1.2

Playing

Surface

ALE

TOP VIEW

BGW

Slide the dimpled end of the Bottom Pole (ALE) into the cement up to

the 16-inch mark. Position the pole next to the playing surface. For

regulation courts, the Alignment Frame (BGW) should cross the playing

surface at the middle of the scored measurements.

SEC

1.3

ALE

BGW

Note: Use a Level to make sure the Bottom Pole is standing vertical. Form

the cement into a downward slope away from the pole to allow water runoff.

Failure to do so may result in premature rusting of the Pole.

NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

Dimpled end

Rebar

Insert the 30” rebar (not included) inside the Bottom Pole (ALE) so it is

about 15” from the top of the pole. Check the pole several times within

the ﬁ rst hour to make sure that all sides are vertical and that the 16-inch mark

remains level with the surface.

SEC

1.4

Note: Allow 1-4 hours for the concrete to set.

30” Rebar

NO HARDWARE REQUIRED FOR THIS PAGE

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

Mix the remaining 1/2 bag of concrete. Fill the Bottom Pole (ALE) with

concrete until it reaches the top of the rebar (about 15” from the

top of the pole). Tamp the concrete down in the Bottom Pole with

a broom handle to remove air pockets. Clean all concrete off the

outside of the pole. You may now remove the Alignment Frame (BGW).

Allow the concrete to set for at least 72 hours before installing the rest of the

system onto the Bottom Pole.

SEC

1.5

Cement Level

Inside Pole

15”

Rebar

Note: STOP HERE! The concrete must cure for at least 72 hours (3 days) before

installing the rest of the system. In humid climates or wet weather, allow additional

time for the concrete to cure. Do not proceed until the curing process is complete.

NO HARDWARE REQUIRED FOR THIS PAGE

Page is loading ...

Lifetime 90469 Owner's manual

Lifetime 90469 Owner's manual

Lifetime 90469 Owner's manual

Related papers

Other documents