Danfoss Drip drain Installation guide

VMBQH22J

SE – Monteringsinstruktion droppskål.................... 4

DE – Montageanweisung Auffangschale.................. 6

FI – Tippakaukalon asennusohje ........................8

EN – Assembly instructions drip tray ....................10

DA – Monteringsanvisninger drypbakke .................12

NO – Monteringsanvisning dryppskål....................14

FR – Instruction de montage, réservoir à condensats ....16

ES – Instrucciones de montaje, bandeja de goteo .......18

CS – Pokyny pro montáž odkapávací mísy ...............20

ET – Vee kogumisanuma kokkupaneku juhend ..........22

NL – Montage-instructies, lekbak........................24

PL – Instrukcja montażu, taca ociekowa . . . . . . . . . . . . . . . . . 26

Page is loading ...

3

VMBQH22J

Circuit diagram, drip tray (available in english only).

Page is loading ...

10

VMBQH22J

EN – Assembly instructions

drip tray

The drip tray accessory is used to collect the water from the outdoor

unit’s heat exchanger during defrosting and transport it to a suit-

able location. In order to avoid the water freezing in the drip tray, it is

equipped with an electric coil.

Components

The drip tray’s accessory set contains the following components:

1 x Drip tray

1 x Transformer

3 x M6 screws

1 x Relay set containing:

1 x Terminal block 125

1 x Relay K5, Phoenix

1 x Relay K6, Carlo Gavazzi

1 x Cable set:

Figure 1: Cable set

Summary

The drip tray is fitted to the outdoor unit’s stand•

The transformer is suspended from the stand’s cross stay•

The outlet pipe/hose is fitted•

The relay set is fitted to the heat pump•

Electrical connection to heat pump and outdoor unit•

⚠

Before any electrical work commences, the power supply must

be turned off using the safety switch.

Fitting the drip tray

1. Unpack the drip tray and check that all the components have

been delivered.

2. Fit the drip tray from the rear of the outdoor unit.

3. Turn the drip tray so that the pre-drilled holes in the stand line

up with the drip tray’s screw holes.

4. Lift the drip tray into place.

Figure 2: The drip tray.

5. Secure the drip tray using three M6 screws.

Figure 3: Mounting screws.

Fitting a transformer

6. Suspend the transformer from the stand’s cross stay.

Figure 4: Transformer.

Fitting an outlet pipe/hose

7. If necessary, place a heating cable in the outlet pipe/hose (deliv-

ery does not include a heating cable).

8. Connect the outlet pipe/hose to the outlet in the bottom of the

drip tray.

9. Lead the outlet pipe/hose away to a suitable location.

11

VMBQH22J

Fitting the relay set to the heat pump

The relay set ensures that there is no re-freezing in the drip tray once

defrosting has finished.

The K6 relay has three setting options on the front, where you can

adjust the relay’s function, time and range.

Dr (FUNCTION) stands for “Delay on release”, which means that the

power feed is maintained while you are adjusting the two other set-

tings.

TIME represents how many time units are counted before the power is

interrupted.

RANGE represents how long a unit will last.

Figure 5: The relay set fitted to the heat pump.

Position Name

1 Defroster card

2 Terminal block, 125

3 Relay K5, Phoenix

4 Relay K6, Carlo Gavazzi

10. Fit the terminal block and the two relays in the positions shown

in the figure above.

11. Set relay K6 to default setting as per the figure below:

Figure 6: Default setting for relay K6.

This setting means that the power will be maintained for 0.5 hours (5 x

0.1h) once defrosting has finished.

Electrical connection to the heat pump

12. The electrical connection to the heat pump is made using the

attached cable set and the junction clamps, as per the wiring

diagram, figure 7. (The cables have the equivalent marking

where they are to be connected.)

Electrical connection to outdoor unit

Figure 7: Electrical connection for outdoor unit.

13. Loosen and remove the outdoor unit’s side panel.

14. Feed the transformer cable into the outdoor unit’s connection

box.

15. Connect the transformer cables to the neutral terminal block

(N/220) and terminal block 126.

16. If required, feed through the heating cable for the outdoor

unit’s connection box.

17. Connect the heating cable’s cables to the neutral terminal block

(N/220) and terminal block 127.

18. Connect a 230V supply from terminal block 125 in the heat

pump to terminal block 125 in the outdoor unit’s connection

box.

19. Replace the side panel.

1 2 3

4

0p

In

Id

Io

Dr

R

Rb

FUNCTION

0,1s

1s

6s

60s

0,1h

1h

10h

RANGE

1

2

3

4

5

6

7

8

9

10

TIME

FUNCTION: Set to Dr (Delay on

release)

TIME: Set to 5

RANGE: Set to 0.1h

0V

230V

Fan, high speed

Fan, motor protection

cut out

Fan, low speed

Defrost sensor

Heat, drip tray

Accessories

Heating cable

Page is loading ...

Danfoss Drip drain Installation guide

Danfoss Drip drain Installation guide

in other languages

Related papers

Other documents