Maxon BMR-CS Maintenance Manual

M-14-23

REV. A

FEBRUARY 2016

Maintenance Manual Contains:

• Warranty Information

• Warnings

• Service Time Chart

• Periodic Maintenance Checklist

• Service and Maintenance Instructions

• Decals

• Hydraulic & Electrical System Diagrams

• Troubleshooting

LIFT CORP.

11921 Slauson Ave.

Santa Fe Springs, CA. 90670

CUSTOMER SERVICE:

TELEPHONE (562) 464-0099 TOLL FREE (800) 227-4116

FAX: (888) 771-7713

WARRANTY/ RMA POLICY & PROCEDURE

NOTE: For latest version of all Manuals (and replacements), download the

Manuals from Maxon’s website at www.maxonlift.com.

LIFTGATE WARRANTY

Type of Warranty: Full Parts and Labor

Term of Warranty: Standard Liftgates - 2 years from ship date or 6,000 cycles

Premium Liftgates - 2 years from ship date or 10,000 cycles

This warranty shall not apply unless the product is installed, operated and maintained in accordance with MAXON Lift’s speciﬁ cations as set forth in

MAXON Lift’s Installation, Operation and Maintenance manuals. This warranty does not cover normal wear, maintenance or adjustments, damage or

malfunction caused by improper handling, installation, abuse, misuse, negligence, or carelessness of operation. In addition, this warranty does not

cover equipment that has had unauthorized modiﬁ cations or alterations made to the product.

MAXON agrees to replace any components which are found to be defective during the ﬁ rst 2 years of service, and will reimburse for labor based on

MAXON’s Liftgate Warranty Flat Rate Schedule. (Copy of the Flat Rate is available at www.maxonlift.com.)

All warranty repairs must be performed by an authorized MAXON warranty facility. For any repairs that may exceed $500, including parts and labor,

MAXON’s Technical Service Department must be notiﬁ ed and an “Authorization Number” obtained.

All claims for warranty must be received within 30 Days of the repair date, and include the following information:

1. Liftgate Model Number and Serial Number

2. The End User must be referenced on the claim

3. Detailed Description of Problem

4. Corrective Action Taken, and Date of Repair

5. Parts used for Repair, Including MAXON Part Number(s)

6. MAXON R.M.A. # and/or Authorization # if applicable (see below)

7. Person contacted at MAXON if applicable

8. Claim must show detailed information i.e. Labor rate and hours of work performed

Warranty claims can also be placed online at www.maxonlift.com. Online claims will be given priority processing.

All claims for warranty will be denied if paperwork has not been received or claim submitted via Maxon website for processing by MAXON’s Warranty

Department within 30 days of repair date.

All components may be subject to return for inspection, prior to the claim being processed. MAXON products may not be returned without prior written

approval from MAXON’s Technical Service Department. Returns must be accompanied by a copy of the original invoice or reference with original

invoice number and are subject to a credit deduction to cover handling charges and any necessary reconditioning costs. Unauthorized returns will be

refused and will become the responsibility of the returnee.

Any goods being returned to MAXON Lift must be pre-approved for return, and have the R.M.A. number written on the outside of the package in plain

view, and returned freight prepaid. All returns are subject to a 15% handling charge if not accompanied by a detailed packing list. Returned parts

are subject to no credit and returned back to the customer. Defective parts requested for return must be returned within 30 days of the claim date for

consideration to:

MAXON Lift Corp.

10321 Greenleaf Ave., Santa Fe Springs, CA 90670

Attn: RMA#__

MAXON’s warranty policy does not include the reimbursement for travel time, towing, vehicle rental, service calls, oil, batteries or loss of income due to

downtime. Fabrication or use of non Maxon parts, which are available from MAXON, are also not covered.

MAXON’s Flat Rate Labor Schedule takes into consideration the time required for diagnosis of a problem.

All Liftgates returned are subject to inspection and a 15% restocking fee. Any returned Liftgates or components that have been installed or not returned

in new condition will be subject to an additional reworking charge, which will be based upon the labor and material cost required to return the Liftgate or

component to new condition.

PURCHASE PART WARRANTY

Term of Warranty: 1 Year from Date of Purchase.

Type of Warranty: Part replacement only. MAXON will guarantee all returned genuine MAXON replacement parts upon receipt and inspection of parts

and original invoice.

All warranty replacements parts will be sent out via ground freight. If a rush shipment is requested, all freight charges will be billed to the requesting

party.

TABLE OF CONTENTS

SUMMARY OF CHANGES: M-14-23, REVISION A ............................................................. 6

WARNINGS ........................................................................................................................... 7

PERIODIC MAINTENANCE .................................................................................................. 9

DECALS - WELDING CAUTION ........................................................................................... 9

DECALS .............................................................................................................................. 10

PREVENTATIVE MAINTENANCE CHECKLIST ................................................................. 12

PERIODIC MAINTENANCE CHECKS ................................................................................ 14

BMR LUBRICATION DIAGRAM .......................................................................................... 15

CHECKING HYDRAULIC FLUID ........................................................................................ 16

CHANGING HYDRAULIC FLUID ........................................................................................ 18

BLEEDING HYDRAULIC SYSTEM ..................................................................................... 19

REPLACING PARTS ..........................................................................................................20

CLOSING CYLINDER REPLACEMENT ............................................................................ 20

LIFTING CYLINDER REPLACEMENT ............................................................................... 22

RUNNER REPLACEMENT ................................................................................................. 26

HYDRAULIC SYSTEM DIAGRAMS ................................................................................... 45

PUMP & MOTOR SOLENOID OPERATION - GRAVITY DOWN ........................................ 45

PUMP & MOTOR SOLENOID OPERATION - POWER DOWN .......................................... 46

GRAVITY DOWN HYDRAULIC SCHEMATIC ..................................................................... 47

GRAVITY DOWN HYDRAULIC LINES IDENTIFICATION .................................................. 48

POWER DOWN HYDRAULIC SCHEMATIC ....................................................................... 50

POWER DOWN HYDRAULIC LINES IDENTIFICATION .................................................... 52

ELECTRICAL SYSTEM DIAGRAMS ................................................................................. 54

INTERCONNECTING ELECTRICAL SCHEMATIC ............................................................. 54

SINGLE PUMP BOX ELECTRICAL SCHEMATIC - GRAVITY DOWN ............................... 55

DUAL PUMP BOX ELECTRICAL SCHEMATIC - GRAVITY DOWN ................................... 56

SINGLE PUMP BOX ELECTRICAL SCHEMATIC - POWER DOWN ................................. 57

DUAL PUMP BOX ELECTRICAL SCHEMATIC - POWER DOWN ..................................... 58

WIRING HARNESS CONNECTOR IDENTIFICATION ....................................................... 59

WIRING HARNESS TWIST-LOCK CONNECTORS ........................................................... 60

TROUBLESHOOTING ........................................................................................................ 61

PLATFORM WILL NOT RAISE & MOTOR WILL NOT RUN ............................................... 61

PLATFORM WILL NOT RAISE & MOTOR RUNS ............................................................... 62

PLATFORM WILL NOT RAISE LOAD AT RATED CAPACITY ............................................ 64

PLATFORM RAISES AND LOWERS UNEVENLY .............................................................. 66

PLATFORM RAISES HALFWAY & STOPS......................................................................... 68

PLATFORM WILL NOT FOLD ............................................................................................. 70

PLATFORM WILL NOT UNFOLD ........................................................................................ 72

POWER OPEN/CLOSE RELIEF VALVE PRESSURE SETTING ....................................... 74

LIFTING LINE RELIEF VALVE PRESSURE SETTING ....................................................... 75

TROUBLESHOOTING - GRAVITY DOWN ......................................................................... 76

PLATFORM WILL NOT LOWER ......................................................................................... 76

PLATFORM LOWERS SLOWLY ......................................................................................... 78

TROUBLESHOOTING - POWER DOWN ........................................................................... 80

RELIEF VALVE PRESSURE SETTING .............................................................................. 80

PLATFORM WILL NOT LOWER ......................................................................................... 82

PLATFORM LOWERS SLOWLY ........................................................................................ 84

PAGE DESCRIPTION OF CHANGE

COVER Updated REV and date.

49,53

Added hose information for 28 foot extension. Added NOTE about hose with yellow

bands.

55-58 Relay fuse changed to 2 AMP on electrical schematics.

SUMMARY OF CHANGES: M-14-23, REVISION A

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

7

• Do not stand, or allow obstructions, under the platform when lowering the Liftgate. Be sure your

feet are clear of the Liftgate.

• Keep ﬁ ngers, hands, arms, legs, and feet clear of moving Liftgate parts (and platform

edges) when operating the Liftgate.

• Disconnect Liftgate power cable from battery before repairing or servicing Liftgate.

Comply with the following WARNINGS and SAFETY INSTRUCTIONS while maintaining

Liftgates. See Operation Manual for operating safety requirements.

• If it is necessary to stand on the platform while maintaining the Liftgate, keep your feet and any

objects clear of the inboard edge of the platform. Your feet or objects on the platform can become

trapped between the platform and the Liftgate extension plate.

WARNING

!

• Correctly stow platform when not in use. Extended platforms could create a hazard for

people and vehicles passing by.

• Recommended practices for welding on steel parts are contained in the current AWS (American

Welding Society) D1.1 Structural Welding Code - Steel. Damage to Liftgate and/or vehicle, and

personal injury could result from welds that are done incorrectly.

• Recommended practices for welding on aluminum parts are contained in the current AWS

(American Welding Society) D1.2 Structural Welding Code - Aluminum. Damage to Liftgate

and/or vehicle, and personal injury could result from welds that are done incorrectly.

WARNINGS

• Welding on galvanized parts gives off especially hazardous fumes. Comply with WARNING decal

on the galvanized part (

FIG. 7-1). To minimize hazard remove galvanizing from weld area, provide

adequate ventilation, and wear suitable respirator.

FIG. 7-1

• Remove all rings, watches and jewelry before doing any electrical work.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

8

• If an emergency situation arises (vehicle or Liftgate) while operating the Liftgate, release the con-

trol switch to stop the Liftgate.

• A correctly installed Liftgate operates smoothly and reasonably quiet. The only noticeable noise

during operation comes from the power unit while the platform is raised. Listen for scraping, grat-

ing and binding noises and correct the problem before continuing to operate Liftgate.

• Use only Maxon Authorized Parts for replacement parts. Provide Liftgate model and serial num-

ber information with your parts order. Order replacement parts from:

MAXON LIFT CORP. Customer Service

11921 Slauson Ave., Santa Fe Springs, CA 90670

Online: www.maxonlift.com

Express Parts Ordering: Phone (800) 227-4116 ext. 4345

Email: Ask your Customer Service representative

• Keep decals clean and legible. If decals are illegible or missing, replace them. Free replacement

decals are available from Maxon Customer Service.

• Consider the safety and location of bystanders and location of nearby objects when operating the

Liftgate. Stand to one side of the platform while operating the Liftgate.

• Wear appropriate safety equipment such as protective eyeglasses, faceshield and clothing while

performing maintenance on the Liftgate and handling the battery. Debris from drilling and contact

with battery acid may injure unprotected eyes and skin.

• Do not allow untrained persons or children to operate the Liftgate.

• Be careful working by an automotive type battery. Make sure the work area is well ventilated and

there are no ﬂ ames or sparks near the battery. Never lay objects on the battery that can short the

terminals together. If battery acid gets in your eyes, immediately seek ﬁ rst aid. If acid gets on your

skin, immediately wash it off with soap and water.

• Read and understand the instructions in this Maintenance Manual before performing mainte-

nance on the Liftgate.

• Before operating the Liftgate, read and understand the operating instructions in Operation

Manual.

• Comply with all WARNING and instruction decals attached to the Liftgate.

SAFETY INSTRUCTIONS

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

9

Comply with welding CAUTION decals on Lift-

gate runners.

CAUTION

NOTE: See following pages to ﬁ nd the other decals on

Liftgate.

PERIODIC MAINTENANCE

FIG. 9-1

DECALS - WELDING CAUTION

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

10

PERIODIC MAINTENANCE

FIG. 10-1

NOTE: Ensure there is no residue, dirt, or corrosion where decals are attached. If

necessary, clean surface before attaching decals.

FAMILY OWNED DECAL

(2 PLACES)

P/N 283445-01

SERIAL PLATE

FAMILY OWNED

DECAL

P/N 283445-01

DECAL “C”

DECAL “A”

DECAL “F”

DECAL “B”

YELLOW

ALIGNMENT TAPE

P/N 090175-14

DECAL “D”

CAUTION DECAL

(2 PLACES)

P/N 260552

WARNING DECAL

P/N 288966-01

NOTE: Preferred decal layout is shown. De-

cals on the Liftgate are attached at the

factory. If vehicle does not permit this

layout, decals in the manual and de-

cal kit must be applied so that they are

easily visible when approaching vehi-

cle to operate Liftgate. Use good com-

mon sense when locating these decals

on vehicle.

STOW WARNING

DECAL

P/N 282847-01

DECALS

DECAL “E”

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

11

DECAL SHEET

FIG. 11-1

MODEL ORDER P/N DECAL “C”

BMRB-CS35 289163-01 3500 LBS. [1600 KG]

BMRB-CS44 289163-02 4400 LBS. [2000 KG]

DECAL SHEET PART NUMBERS

TABLE 11-1

(REFER TO TABLE 11-1)

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

12

MAXON BMR-CS LIFTGATE

PREVENTATIVE MAINTENANCE CHECKLIST

PERIODIC MAINTENANCE

PM Interval: Quarterly / Annual

Date: / /

Equipment: W/O # Location:

Mechanic: Serial # Model #

Check Appropriate Box. “”

MAXON Quarterly Liftgate PM Procedures

Satisfactory Repair Required Corrected

1

Check your company’s maintenance records to verify when quarterly and

annual PM’s are due.

Satisfactory Repair Required Corrected

2

Check for oil leaks: cylinders, ﬁ ttings, hoses, valves, oil ﬁ lter and ﬁ ttings

inside of pump box.

Satisfactory Repair Required Corrected

3

Check for damage: bent ramps, platform, columns, runners & hydraulic

tubes.

Satisfactory Repair Required Corrected

4 Check for loose or missing nuts, bolts, covers, roll pins, screws and pins.

Satisfactory Repair Required Corrected

5

Check for cracked welds: columns, runners, platform, chain arms, pump

box and door frame.

Satisfactory Repair Required Corrected

6

Check platform lowering speed: Range is 8-22 seconds with unloaded

platform. Check “D” valves for proper operation.

Satisfactory Repair Required Corrected

7 Check platform pins and couplers. Check roller assemblies.

Satisfactory Repair Required Corrected

8

Check platform raising speed: Range is 9-21 seconds with unloaded

platform.

Satisfactory Repair Required Corrected

9

Check open and close speed: Range is 4-7 seconds in either direction.

Adjust if necessary.

Satisfactory Repair Required Corrected

10 Check platform pins and couplers. Check roller assemblies on runners.

Satisfactory Repair Required Corrected

11

Check switches, circuit breaker & wiring connections on Liftgate as well as

inside pump box. Also check that ground strap connections are tight.

Satisfactory Repair Required Corrected

12 Check gear pump for unusual noise (i.e. squealing or excessive RPM).

Satisfactory Repair Required Corrected

13

Check oil level with platform stowed. Refer to oil decal inside pump cover.

The sight glass should be half full. Check oil for contamination. Change if

needed.

Satisfactory Repair Required Corrected

14 Check batteries: load test, corrosion, cables, hold downs and water level.

Satisfactory Repair Required Corrected

15 Check platform chains for wear each time maintenance is performed.

Satisfactory Repair Required Corrected

16 Check operation of retension ramps.

Satisfactory Repair Required Corrected

17 Check all charging and ground cable connections.

Satisfactory Repair Required Corrected

18

Pump EP synthetic grease in each lube ﬁ tting at 2 platform pivots and the 2

roller axles on the 4 tandems. Wipe away grease seepage. Ensure each of

the tandem rollers is clean and free of grease.

Satisfactory Repair Required Corrected

19

Follow your company’s guidelines for completing PM stickers and

maintenance records for the Liftgate.

TABLE 12-1

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

13

MAXON Annual Liftgate PM Procedures

Satisfactory Repair Required Corrected

20 Replace spin-on ﬁ lter in pump box. Change hydraulic ﬂ uid if contaminated.

Satisfactory Repair Required Corrected

21 Inspect wear on slide pads, on the RH and LH runners.

TABLE 13-1

For more detailed information, please refer to the applicable sections in this Maintenance Manual and

the separate Parts Manual. Use only genuine Maxon replacement parts for all repairs.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

14

NOTE: Photocopy the PM CHECKLIST on the preceding page to help keep track of peri-

odic maintenance on the Liftgate. Keep completed form with maintenance records.

Annually

Quarterly

PERIODIC MAINTENANCE CHECKS

Never operate the Liftgate if parts are loose or missing.

WARNING

Check the hydraulic ﬂ uid level in the pump reservoir. Refer to the CHECKING HYDRAULIC

FLUID procedure in the PERIODIC MAINTENANCE section.

Pump EP synthetic grease in ﬁ tting on 2 platform pivots and roller axels on 4 tandems.

Check for worn out links on each of the two platform chains.

Check each end of the two platform chains to make sure they are fastened properly.

Check that all roll pins are in place and protrude evenly from both sides of hinge pin col-

lar. Replace roll pins if necessary.

Check that all WARNING and instruction decals are in place and legible.

Check electrical wiring for chafﬁ ng and make sure wiring connections are tight and free

of corrosion. MAXON recommends using dielectric grease on all electrical connections.

Check hoses and ﬁ ttings for chafﬁ ng and ﬂ uid leaks. Replace if necessary.

Keep track of the grade of hydraulic ﬂ uid in the pump reservoir. Never mix two different

grades of ﬂ uid.

If hydraulic ﬂ uid appears contaminated, refer to the CHANGING HYDRAULIC FLUID

procedure on following page.

Check for rust and oily surfaces on Liftgate. If there is rust or oil on the Liftgate, clean it

off.

Change spin-on oil ﬁ lter.

Inspect for wear on slide pads on the RH & LH runners.

!

NOTE: When replacing parts, refer to Parts Manual for genuine MAXON replacement parts.

Check pump box cover seal. Replace seal if damaged.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

15

FIG. 15-1

NOTE: Lube ﬁ ttings are shown for the tandem roller axles on the LH runner and the pivot

on the LH side of platform. There are also lube ﬁ ttings in the same location on the

tandem roller axles for the RH runner and the pivot on the RH side of the platform.

Refer to the PERIODIC MAINTENANCE CHECKS and PREVENTATIVE MAIN-

TENANCE CHECKLIST for the recommended grease and maintenance interval.

BMR LUBRICATION DIAGRAM

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

16

CHECKING HYDRAULIC FLUID

1. Stow the platform in the up position. Refer

to Operation Manual for instructions.

NOTE: If the hydraulic ﬂ uid in the reservoir is contaminated, do the CHANGING

HYDRAULIC FLUID procedure in this section.

CAUTION

Keep dirt, water and other contaminants from entering the hydraulic system.

Before opening the hydraulic ﬂ uid reservoir ﬁ ller cap, drain plug and hydraulic

lines, clean up contaminants that can get in the openings. Also, protect the

openings from accidental contamination.

Never mix synthetic ﬂ uids with conventional hydraulic ﬂ uids. Hydraulic system

must be purged if the ﬂ uids are mixed.

2. Open the pump box cover to gain

access to full line and ﬁ ller cap

(FIG. 16-1).

4. Reinstall ﬁ ller cap (FIG. 16-1) and close

the pump box cover.

NOTE: Exxon Univis HVI-13 hydraulic ﬂ uid is recommended for operating tem-

peratures of -40 to +120° F. Refer to decal in pump box. The ISO-15 ﬂ uids

in TABLE 17-1 may be used if the recommended ﬂ uids are unavailable. If

necessary, the ISO-32 ﬂ uids in TABLE 17-2 may be used where ordinary

seasonal temperatures are near +100° F or higher.

3. Check if hydraulic ﬂ uid level

is at the full line (FIG. 16-1). If

necessary, remove ﬁ ller cap (FIG.

16-1) and add the correct grade

of hydraulic ﬂ uid until level rises to

the full line (FIG. 16-1).

CHECKING HYDRAULIC FLUID LEVEL

FIG. 16-1

FILLER

CAP

NOTE: Information for checking

hydraulic ﬂ uid level is shown

on a decal on the pump

reservoir.

PERIODIC MAINTENANCE

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

17

ISO-32 HYDRAULIC OIL

BRAND PART NUMBER

CHEVRON HIPERSYN 32

KENDALL GOLDEN MV

SHELL TELLUS S2 V32

EXXON UNIVIS N-32

MOBIL

DTE-13M, DTE-24,

HYDRAULIC OIL-13

TABLE 17-1

TABLE 17-2

ISO-15 OR MIL-H-5606 TYPE HYDRAULIC OIL

BRAND PART NUMBER

CHEVRON FLUID A, AW-MV-15

KENDALL GLACIAL BLU

SHELL TELLUS S2 V15

MOBIL DTE-11M

ROSEMEAD THS FLUID 17111

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

18

1. Place empty 5 gallon bucket under drain plug.

GRAVITY DOWN LIFTGATES

4. Reinstall ﬁ ller cap (FIG. 18-1).

POWER DOWN LIFTGATES

1. Place empty 5 gallon bucket under drain plug.

CHANGING HYDRAULIC FLUID

PERIODIC MAINTENANCE

3. Remove ﬁ ller cap (FIG. 18-1).

Reﬁ ll reservoir until hydraulic

ﬂ uid level until level rises to the

full line (FIG. 18-1).

FULL LINE

CAUTION

Keep dirt, water and other contaminants from entering the hydraulic system.

Before opening the hydraulic ﬂ uid reservoir ﬁ ller cap, drain plug and hydraulic

lines, clean up contaminants that can get in the openings. Also, protect the

openings from accidental contamination.

Never mix synthetic ﬂ uids with conventional hydraulic ﬂ uids. Hydraulic system

must be purged if the ﬂ uids are mixed.

NOTE: Exxon Univis HVI-13 hydraulic ﬂ uid is recommended for operating tem-

peratures of -40 to +120° F. Refer to decal in pump box. The ISO-15 ﬂ uids

in TABLE 17-1 may be used if the recommended ﬂ uids are unavailable. If

necessary, the ISO-32 ﬂ uids in TABLE 17-2 may be used where ordinary

seasonal temperatures are near +100° F or higher.

2. Open and lower platform. Remove the drain plug

(FIG. 18-1). Drain hydraulic ﬂ uid from system.

Reinstall drain plug.

FILLER CAP

DRAIN PLUG

SINGLE PUMP BOX

FIG. 18-1

5. Reinstall ﬁ ller cap (FIG. 18-1).

4. Remove ﬁ ller cap (FIG. 18-1).

Reﬁ ll reservoir until hydraulic

ﬂ uid level until level rises to the

full line (FIG. 18-1).

3. Open and lower platform. Remove the drain plug

(FIG. 18-1). Drain hydraulic ﬂ uid from system.

Reinstall drain plug.

2. Press the POWER DOWN ON DEMAND button

on the column switch to set the Liftgate in Grav-

ity Down mode. Refer to Operation Manual for

instructions.

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

19

BLEEDING HYDRAULIC SYSTEM

1. Use UP/DOWN toggle switch to lower the

opened platform to the ground.

2. Loosen, but do not disconnect, the nut

connecting hydraulic line to ﬁ tting on

pressure compensated ﬂ ow control valve

(FIG. 19-1) at top of both cylinders.

3. Set the UP/DOWN switch on the RH runner in

the UP position for approximately one second

and then release the switch. Wait ten seconds

and then switch to UP and release. Repeat

this step until there is no air bubbling from the

loosened line ﬁ ttings.

5. Use UP/DOWN toggle switch to raise and

lower the platform to make sure the Liftgate

operates correctly.

4. Tighten nut on hydraulic line (FIG. 19-1).

FIG. 19-1

NOTE: Perform this procedure at a place where Liftgate platform can be

lowered to lowest point of travel. Get a helper to operate Liftgate

control switch.

PRESSURE COMPENSATED

FLOW CONTROL VALVE

NUT

(HYDRAULIC

LINE)

FITTING

11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713

20

CLOSING CYLINDER REPLACEMENT

1. UNFOLD the platform. Lower the

platform (DOWN) to comfortable

height for work. Upper pin must be

lower than the bottom of the column

(see FIG. 20-1).

2. Disconnect the hydraulic hoses from

lower end of cylinder (FIG. 20-2). Plug

hoses to prevent spills.

3. Remove the upper roll pin (FIG. 20-2)

from the runner and then remove the

upper pin.

FIG. 20-2

RUNNER

HYDRAULIC HOSE

ROLL PIN

UPPER PIN

REPLACING PARTS

FIG. 20-1

UPPER PIN

(CLOSING

CYLINDER)

COLUMN

CYLINDER

Page is loading ...

Maxon BMR-CS Maintenance Manual

Maxon BMR-CS Maintenance Manual

Related papers

Other documents