Electro-Voice SL6.2M User manual

Brand: Electro-Voice

Model: SL6.2M

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

SL 6.2

Electro-Voice SL6.2M is a high-output speaker with a wide frequency response, making it suitable for small to medium theater surround applications. Its high-energy 6" low frequency transducer and pure titanium 1" high frequency neodymium transducer deliver wide dynamic range and smooth coverage. The SL6.2M features full bandwidth protection and overload protection, ensuring reliability and durability even at high volumes. The included Strong-Arm-Mount allows for easy and flexible aiming, making it easy to position the speaker for optimal sound distribution.

Model SL6.2M

Extended Range

High Output Speaker

Technical Specifications:General Description:

The SL6.2M provides high efficiency, high power

handling, and extended frequency response in a very

compact, plastic enclosure. It’s proven performance

and reliability position it as the correct choice for

small to medium theater surround applications.

The SL6.2M features a high-energy 6" low frequency

transducer, a pure titanium 1" high frequency

neodymium transducer mounted on a 100° x 100°

waveguide, and a crossover network with full

bandwidth protection. These components provide

wide dynamic range, smooth coverage, and

exceptional reliability.

One person installation is simple using the included

EV Strong-Arm-Mount

. It provides ease of location

and aiming not possible with other brackets.

The SL6.2M’s performance, reliability, and shape

make it ideal for digital age theaters.

Key Features:

• 46 Hz – 20 kHz Response

• 250W Power Handling

• 90 dB High Sensitivity

• Full-Bandwidth overload protection

• Strong-Arm-Mount

for easy, flexible

aiming

• Lightweight, unobtrusive plastic enclo-

sure

• Easy access input terminals

esnopseRycneuqerF

)Bd01-(zHk02-zH84

gnildnaHrewoP

sttaw052

ytivitisneS

m1/W1,Bd09

ecnadepmIsmho8

LPSdetaluclaCxaMBd611

egarevoClatnoziroH

°001

egarevoClacitreV

°001

ycneuqerFrevossorCzHk8.1

recudsnarTFL)mm001(”6

recudsnarTFH)mm52(”1

noitcetorPmetsySlluF

noisnepsuSsixA-itluM

noitatoRxgniwS°09x°001

slanimreTAG21stpecca,gnirpS

lairetaMerusolcnE)elbatniap(SBA

)DxWxH(miD

xmm914(”57.11x"9x”5.61

)mm892xmm822

)hcae(thgieWteN)gk5.4(sbl9.9

thgieWgnippihS)gk4.01(sbl32

seirosseccAdedulcnIMAS

™

yekxeh,

)gnitnuomllaw(ecapSflaH

esionknipsuounitnocnahtretaergBd3:gnitaRmargorPmreTgnoL

gnitar

)gnitnuomllaw(ecapSflaH:gvA

nalplacitrevnisixagnolhtiwdetnuomnehW

Packing List

Listed and illustrated below are the parts in-

cluded in each boxed pair of EVID™ speakers.

Product Feature Identification

Illustrated below are the major components

of the EVID™ Series full-range speakers.

EVID SL6.2M

A 2 Speaker system

B 2 SAM™ assembly

C 2 Large logo cap

C 2 Small logo cap

D 1 Data sheet/Instructions

E 1 Warranty card

F 1 SAM™ mounting tool

Figure Quantity Part

EDF

Figure 1: EVID™ components

Input wire

connectors

Connection eyebolt

for seismic

security cable

Figure 3: EVID™ features (back)

A. Shielded woofer

B. Coherent Coverage Waveguide horn

C. Low-frequency port

D. Treated woofer cone

E. Durable zinc-plated steel grille (not shown)

F. Cast aluminum Strong-Arm-Mount™ (SAM™)

G. Over 100 degrees of swing; 90 degrees

of rotation

H. Simple keyed socket head adjustments

I. Titanium dome tweeter with neodymium

magnet structure

(E)

Figure 2: EVID™ features (front)

Installation and Wiring

Step 1: Mount the SAM™ Bracket

The SAM™ bracket can be mounted on

either side of the speaker, enabling optimal

configuration for any installation. First,

determine whether the bracket should be

mounted on the left or right side of the

speaker (do not bolt the speaker to the

bracket). It is best to mount the bracket on

the side away from the direction in which

the speaker will be aimed. This ensures

that the full sweep angle is available for

aiming on that side and provides easier

access to the sweep tightening bolt on the

wall bracket (see step 2). For safety,

make sure the mounting surface can

support more than the speaker's

weight! Use only industry-accepted fasten-

ers and mounting methods when mounting

the bracket. Consult an expert if you are

not sure.

For standard vertical installation mount

the SAM™ bracket as shown in Figure 4.

For horizontal mounting configurations,

mounting the bracket on the bottom side

(as in Figure 5) is easiest and safest, and

allows the speaker to be mounted closer to

the ceiling.

Step 2: Mount the Speaker to the

SAM™ Bracket

Attach the speaker to the SAM™ bracket

with the socket head bolt, as shown in

Figure 6.

Secure the speaker with the provided

security tool by tightening the two socket

head bolts as shown. After selecting the

proper horizontal angle, secure the swing

axis as shown by tightening bolt A. Next,

select the proper vertical angle with the

aid of the angle markers as shown in

Figure 7. Then secure the rotation axis by

tightening bolt B.

SAM™

Ceiling

Figure 5: SAM™ mounted on bottom

SAM™

Figure 4: SAM™ mounted on side

Figure 6: Attach SAM™

Bolt A

(swing)

Bolt B

(rotation)

15˚ angle markers

Figure 7: Tighten socket-head bolts

Attach both logo caps as shown in Figure 8

after tightening and securing the speaker.

Step 3: Wire the Speaker

Connect the wires to the speaker at the

back terminal plate observing the polarity

of the connections. The push-terminals

accept banana connector plugs.

Step 4: Secure the Seismic Tab

Connection Point

The rear of the enclosure includes an eye-

bolt for connection to a seismic restraint.

Connect it to a properly rated hardware fit-

ting that is securely installed independent-

ly of the SAM™ bracket. Even if your local

construction code does not require the

installation of secondary support, its use is

highly recommended for further security.

Step 5: Test System Operation

After all connections are made, test the

complete system operation. The Trouble-

shooting Table on the next page will assist

in locating many speaker-related problems.

EV logo cap

(large)

EV logo cap

(small)

Figure 8: Attach logo caps

Connect seismic

security cable

Figure 9: Secure seismic security cable

Problem Possible Cause(s) Action

1. No sound Amplifier Connect a known working test speaker to the amplifier

outputs. If there is no sound, check that all the elec-

tronics are on, the signal routing is correct, the source

is active, the volume is turned up, and so on. Correct/

repair/replace as necessary. If there is sound, the

problem is in the wiring.

Wiring Verify that you have connected the correct wire pairs to

the amplifier. Play something at low level through the

amplifier (for example, from a CD player or tuner).

Connect the test speaker in parallel with the malfunc-

tioning line. If the sound has gone or is very weak, the

line has a short in it (possibly a severe scrape, pinch,

or staple puncture). If the sound level is normal, the

wire is open (possibly a cut wire or a missed connec-

tion). Using the test speaker, move down the line and

test each connection/junction until you find the problem

and correct it. Observe proper polarity.

2. Poor low- Speakers wired When two speakers are connected out of polarity

frequency out-of-polarity (out of phase), the low frequencies will cancel each

response other acoustically. Carefully observe the wire markings

or tracers on your speaker wires. Verify that the ampli-

fier (+) terminal is connected to the red speaker termi-

nals and the amplifier (–) terminal is connected to all

the black speaker terminals.

Improperly wired Using a test speaker as described above, verify that

subwoofer panel all amplifier and speaker wires are connected to their

proper terminals with the correct polarity. Reversing

just one set of amplifier wires can cut out all bass

output from the subwoofer.

3. Intermittent output Faulty connection Check all connections at amplifier and speakers to

such as crackling ensure they are clean and tight. If the problem persists,

or distortion it may be in the amplifier or wiring. See no. 1 above.

4. Constant noise Defective amplifier If the noise is present but no program material is

such as buzzing, or other electronic playing, the likely cause is the signal chain in the elec-

hissing, humming device tronics. Evaluate each component as necessary to iso-

late the problem.

Poor system Check and correct the system grounding, as required.

grounding or

ground loop

If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or

Electro-Voice distributor.

Troubleshooting Table

Architecture & Engineering Specs:

The loudspeaker shall be a two-way system consisting of one 6”

(152mm) low-frequency transducer, a 1” (25mm) high-frequency

transducer with a Coherent Coverage Waveguide, and a frequency-

dividing network installed in a vented, line-array enclosure. The

network shall include a passive limiter for both the low-frequency

and high-frequency transducers. The loudspeaker system shall meet

the following performance criteria: Power handling, 250-Watts long

term program using IEC268-5 shaped pink noise; Frequency

response, 46 Hz - 20 kHz (-10 dB from rated sensitivity); Pressure

sensitivity, 90 dB at one watt, 200 Hz -10 kHz at one meter; Impedance,

8 ohms nominal, 6 ohms minimum. The high-frequency transducer

shall drive a waveguide to cover evenly 100° horizontally by 100°

vertically. The enclosure shall be molded of acrylic butyl styrene. The

enclosure shall be 16.5” (419mm) high, 9” (228mm) wide, 11.75”

(298mm) deep. The finish shall be a paintable black. The grille shall

be zinc plated, powder coated for corrosion resistance, and

restrained with a safety leash. The loudspeaker shall be adjustable

over a range of 100° horizontally and 90° vertically. The support

bracket shall be low profile and integral with the enclosure.

U.S.A. and Canada only. For customer orders, contact Customer Service at:

800/392-3497 Fax: 800/955-6831

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

+ 49 9421-706 0 Fax: + 49 9421-706 265

Other International locations. For customer orders, contact Customer Service at:

+ 1 952 884-4051 Fax: + 1 952 736-4212

For warranty repair or service information, contact the Service Repair department at:

800/685-2606

For technical assistance, contact Technical Support at: 866/78AUDIO

Specifications subject to change without notice.

12000 Portland Avenue South, Burnsville, MN 55337

Phone: 952/884-4051, Fax: 952/884-0043

www.electrovoice.com

Part Number 38110-153 Rev A

Beamwidth:

Frequency Response and Impedance:

Directivity:

Block Diagram:

Side

Wall Plate

Front

Top

Dimension Drawings:

Electro-Voice SL6.2M User manual

Brand: Electro-Voice

Model: SL6.2M

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

SL 6.2

Download PDF

report

Electro-Voice SL6.2M User manual

This manual is also suitable for

Electro-Voice SL6.2M User manual

Related papers

Other documents