TRC 14 CCD
Installation
and user manual
Scope of delivery
(1) Colour Camera TRC 14 CCD
(2) Camera bracket
(3) Cover profile, sun shield
(4) Connection cable
(5) Fastening Material
* Specification is subject to change without prior notice
4)
20 m cable
(1) (2)
(3)
5)
Spare parts
* Specification is subject to change without prior notice!
1
Camera Installation
Warning!
If installing the camera alters the vehicle height or length the
vehicle must be inspected by the appropriate authorities.
Camera installation and fixing it so securely that it cannot
under any circumstances fall off and injure bystanders.
Technical Information
(1) The camera is built in aluminum housing.
(2) The camera transmits image and sound via connection cable to a monitor.
(3) The camera transmits image to the monitor equal to the back view of the
driving mirror.
(4) The LEDs improve night vision.
(5) Camera main elements:
6-pin connection cable (5)
Microphone (2B) Infrared
LEDs(4)
* Specification is subject to change without prior notice!
1 2B/5 2A 3 4/5 5
2
Camera Installation
Installation instruction
• The camera must be attached at a height of at least 2 m to provide suitable
viewing angle.
• Ensure that the installation location of the camera makes the camera bracket
sufficiently firm.
• Mount the camera in the middle of the rear of the vehicle and horizontal aswell.
• With screws fitted through the body is the most secure type of attachment, please
observe following:
- Sufficient space for mounting behind the body and for the drill head to come
out on the other side is essential.
- Suitable measures must be taken to prevent water penetration through any holes
made (e.g. using screw and sealant, using spray for outer attachment parts
with sealant).
Mount the camera in the middle of the rear of the vehicle and horizontal as well
3
Camera installation using threaded screws
• Tap hole M5 (Drill 4.2 mm holes) at the
points just marked.
• Deburr all drill holes.
• Greasing the threads of the bolts,
rust protection.
• Screw the camera bracket on with the
M5 x16 mm threaded screws.
Camera installation
• Self-tapping screws may only used if the
steel panels have minimum thickness
of 1,5 mm.
• Attach the camera holder on the chosen
location.
• Mark at least two different points for the
drill holes.
• Pre-punch the marked points.
• Drill 4.5 mm holes at the points just marked
• Deburr all drill holes.
• Greasing the threads of the bolts, rust
protection.
• Screw the camera bracket on with the
5 x16 mm self-tapping screws.
Camera installation using self tapping screws
• Drill the through hole for camera connection
cable.
• Drill a hole of 13 mm diameter near the
camera.
• Deburr the drill hole.
• Greasing the drill hole, prevent corrosion.
• Use cable sleeves in all sharp edged ducts.
4
• Push the camera into the camera bracket.
• Fastening and centering the camera loosely with two screws M3x6 mm in the
middle threaded drill holes (A).
• Align the camera to have the lens at an angle of approx. 60° to the perpendicular
axis of the vehicle (B).
• Push the camera guard over the camera that the central drill holes slide over
both screws heads and the slots are aligned with those of the camera
bracket (C ).
• Secure camera guard with four screws M3x8 mm in the slots.
• Tighten all screws after camera is aligned, checking function and setting camera,
if applicable monitor connection is necessary.
• Never mount camera without camera guard.
• To mount camera only use the supplied screws.
Camera connection
• Guide the camera cable into the vehicle interior.
• Insert the plug of the camera cable into the socket of the extension cable.
• Apply few amount of grease into the plug, prevent corrosion.
• Wrap the connection with the sealing tape supplied, protection against water
penetration. ·
• Plug connection should be accessible easily, considerably for dismantling work.
Checking the function and setting
• Check the function of the camera after monitor is connected. ·
• Align camera using the image on the monitor show the rear or the number of
vehicle at the bottom edge of the screen, and the middle of the number should
be in the middle of the screen.
• Tighten all fastening screws of the camera bracket.
• Other settings of the camera can be made on the monitor.
5
( A ) ( B )
( C )
10
1
2
4
3
5
6
7
8
9
1) Navigator GPS Teleco M-DVD5566 TRUCK
2) Rear camera connector
3) Connection cable
4) Video connector
5) Black: negative pole
6) Yellow: image inversion (-)
7) Red: positive pole (12 Vcc)
8) 20 m cable
9) Rear camera
10) Audio (do not connect)
11) The sensor must be under the
camera in order for the image to
be straight.
Schematic Installation
Light sensor
6
11
Technical Data
Dimension (b with bracket): approx. 95x70x86mm(WxDxH)
Power supply: approx. 2.4 watts with heater
Operating voltage: 11-16 DC
Picture sensor: Sony Effio sensor
Resolution: 270.000 pixels
Light sensitivity: <0.1 lux or 0 lux with LED
Operating temperature: -20°C to +65°C
Protection class: IP69K
Vibration resistance: 8 g
Weight: approx. 350 g
Viewing angle: approx. 110° diagonal
Video standard: PAL
Mirror function: detachable
Certification: CE, E-mark, ROHS,
Features
• Anodized salt spray proof aluminum die casting housing with protective
cover and mount in stainless steel
• Temperature controlled heater
• Electronic brightness adjustment
• IR-LED low light compensation
• Built-in microphone
Certification
This products has the E11 certification
RoHS
Made in China
20_11_2015
/