Maytag MDB6701AWW - BI DW 5LVL SANI ESTAR Owner's manual

?vlP.YI AG

MDB-9

=. • 1

Cannot be Washed ........... 2

Operating Tips .............. 3

Loading ................. 3-6

Dishwasher Use ............ 7

Cycles, Options

and Lights .............. 8-11

Care &Cleaning ........... 12

Troubleshooting ........ 13-14

Warranty & Service ........ 15

Guide d'utilisation

et d'entretien .............. 16

Gui_ de Uso y Cuidado ..... 32

Part No. 6 920186 A www.maytag.com _2005 Maytag Appliances Sales Co.

:Safety

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this

manual are not meant to cover all possible conditions and

situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

tile dishwasher.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Important Safety Instructions

zfT_

Products with a .u_ label have been listed with

Underwriter's Laboratories, Inc. - those with a CSA tag have

been listed with Canadian Standards Association.

Nevertheless, as with any other equipment using electricity

and moving parts, there is a potential hazard.

1. Readall instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before

attempting to service.

4. Toavoid electrical shock hazard, the sides and back

must be enclosed and the front panels must be

attached before electrical power is applied to the

dishwasher. Refer to the installation instructions for

proper grounding procedures.

5. Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play

in, with, or around this dishwasher.

Z Toreduce the risk of injury when loading items to be

washed, sharp or pointed items should be located with

the handles up. Also, load sharp items sothey are not

likely to damage the door seal.

8. Do not touch the heating element on the bottom of

the tub during or at the completion of a cycle. It will

be [lot.

9. Use only detergents and rinse additives designed for a

residential automatic dishwasher. Never use soap,

laundry detergent, or hand washing detergent in your

dishwasher. Keep these products out of reach of

children.

10. Do not sit, stand on or abuse the door or dish racks of

the dishwasher.

11. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. Hydrogen gas is

explosive. If the hot water system has not been used

for such a period, turn on all hot water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this process.

12. Do not wash plastic items unless marked "dishwasher

safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

13. Do not tamper with controls.

14. Toprevent accidental child entrapment and

suffocation risks, always remove the door to the

washing compartment when removing an old

dishwasher from service or discarding it.

15. Use caution when unloading the dishwasher. Dishes

will be hot if unloaded shortly after a cycle has

completed.

16. Certified residential dishwashers are not intended for

licensed food establishments.

17 Toavoid water, mold or mildew damage to your home,

inlet and drain hose connections should be checked

periodically for leaks.

Save These Instructions

for Future Reference

WhatCanandCannotBeWashed

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

Aluminum Yes, except anodized. High water temperature and detergents may affect finish.

Cast Iron No Seasoning will be removed, and iron will rust.

China/Stoneware Yes, except antique or Always check manufacturer's recommendation before washing.

hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold

leaf may discolor.

Crystal Yes, except antique or Always check manufacturer's recommendation before washing.

delicate crystal. Some types of leaded crystal may etch with repeated washings.

Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.

Glass Yes A specialty glass called milk glass can yellow with repeated

dishwasher washing.

Gold-Plated No Will discolor.

Flatware

Pewter, Tin No

Plastics Yes, top rack, except Always check manufacturer's recommendation before washing.

disposable plastic Plastics vary in their capacity to withstand high water

items, temperatures and detergents. Disposable plastic items are not

dishwasher safe for this reason.

Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing

immediately. Prolonged contact with foods containing salt,

vinegar, milk products or juice could damage finish.

Sterling Silver or

Silverplate

No, if has commercial

"darkening".

Always check manufacturer's recommendation before washing.

Run a Rinse Only cycle (select models) if not washing

immediately. Prolonged contact with food containing salt, acid or

sulfide (eggs, mayonnaise and seafood) could damage finish.

Commercial "darkening" may be removed by detergent.

Wooden Items No Wood may warp, crack or discolor.

2

0perutin9Tips

Before You Start

• Don't prerinse. Simply scrape off any bones or

large food particles.

• If connected to a food waste disposer, make certain

the disposer is empty before starting the

dishwasher.

• Scrape off tomato-based food soils (see page 12).

• Remove certain foods such as mustard,

mayonnaise, lemon juice, vinegar, salt or dressings

from stainless steel flatware as soon as possible.

These foods may cause rusting and pitting if allowed

to remain in contact with the surface for an extended

period of time.

Operating the Dishwasher

1. After loading the dishwasher and adding detergent,

select the desired cycle and options by pressing

the pads. The indicator lights for the selected cycle

and options will illuminate. To cancel an option

press the pad again.

2. To start a cycle, close the door until it latches then

press the START/Cancel pad once. After a pause,

the fill will begin. The display countdown (select

models) will flash until START/Cancel is pressed.

Note

• If START/Cancel is not pressed within 30

seconds of choosing your cycle, the dishwasher

will turn off.

.

The dishwasher remembers your last cycle so you

do not have to reset the cycle each time. To start

the dishwasher using the same cycle and options

selected on the previous wash, just press the

START/Cancel pad.

To cancel a running cycle, press the

START/Cancel pad once. The dishwasher will

drain, then shut off. To turn the dishwasher off

without draining, press the START/Cancel pad

twice. To prevent unplanned cycle or option

changes, these selections are "locked in" after 1

minute.

Note

• If a cycle pad is pressed after the controls have

been "locked in," the light above the current cycle

will flash three times.

Adding a Forgotten Item

For best cleaning, the forgotten item should be added

early in the cycle.

1. Grasp door handle and unlatch door without

opening completely. All lights will flash to indicate

that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

4. Close and latch the door. Lights will stop flashing

when the door is properly shut. After a slight delay,

the cycle resumes automatically at the point of

interruption.

Notes

• If the door is opened during a running cycle,

there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

• Extended interruption of the wash cycle is not

recommended.

toadln9

General Recommendations

[Rack features vary by model)

• Items can be centered behind a single tine or loaded

at an angle to maximize space.

• Avoid blocking or preventing the spray arms from

spinning freely. Do not allow items to extend beyond

the racks.

• Face soiled surfaces toward the center of the

dishwasher.

For best dishwashing results follow guidelines on

following pages to determine the best arrangement for

your items.

Cont.

Loading

10 Place Setting Load

Upper Rack

3saucersare

loadedonthe

rackunderthe

Stack-RackTM

Shelf

[select

models)

Lower Rack

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates,

bowls, pans, long-handled utensils etc. can be loaded

in this rack. Do not load glasses over the tines.

The Stack-Rack TM (select

models) on the right side

of the upper rack folds

up or down for loading

flexibility. Fold it down to

hold long-handled

knives, spatulas and

spoons or short items like cups or juice glasses. Fold it

up for taller items like glasses, bowls, plates, etc.

The edge of the Stack-

RackTM (select models) is

designed to hold

stemware in place. Taller

stemware will fit better on

the right side as the

upper rack is deeper on

this side.

The Folding Tines (select

models) located in the

front right corner provide

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

To lower tines, carefully push the tines out of each

holder toward the center of the rack and lay the tines

down.

The Cup Clips (select

models) located in the

center of the upper rack

can be used to hold

light-weight plastic items,

cooking utensils, knives,

etc. in place. Clip the

item between the tine

and the clip.

The Vari-Lock TM Snugger

(select models) on the

left secures lightweight

items in place. It can be

adjusted by grasping the

wavy wire and rotating it

left to snug items against

the outer rack or to the

right to rest on top of light items. Do not load items

on top of the wire.

For best results with tall

glasses, rest the bottom of

the glass against the wavy

wire of the Vari-Lock TM

Snugger (select models).

4

Loading

Lower Rack

A variety of items such as

dinner plates, mixing bowls,

pots and pans and baking

dishes can be loaded in this

rack.

Tall items such as bakeware

and large platters can be

placed on the left side.

With the Stack-

Rack TM (select

models) shelf

raised, thin items

like cookie sheets

or pizza pans

may be placed

along the left

side. With the shelf down, two levels of glasses and

cups can be loaded. Stack-Rack TM style varies by

model.

Positioning the Fold-

Away TM Tines (select

models) flat in the back,

left corner provides

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

Back

Convertible Tines (select

models) in the back, right

corner can be adjusted to

provide narrow spacing for

loading plates or wide spacing

for loading deep bowls, pots or

pans. Flip tines up for narrow

spacing or down for wider

spacing.

Back

iii_TM _;iii_

;/jJ;"

Utensil Baskets

Removable Standard Utensil Basket (select

models)

For best cleaning results, prevent

items from nesting together by

placing some items in the basket

with handles up and some with

handles down. Load knives

handles up and spoons and forks

handles down, through the slots

in the hinged covered section(s)

(when closed).

Be sure that thin, finely pointed items do not extend

through the basket. This could block the lower wash

arm.

Small, lightweight items like baby spoons and plastic

measuring spoons should be placed in the section(s)

with the hinged cover(s).

Split & FitTM Utensil Basket

(select models)

The split silverware basket can

be separated and placed in

several locations in the lower

rack. Load flatware and utensils

into both sections or just one,

depending on your load.

To split the basket, hold the

basket

firmly along

the sides.

Unlock

baskets as

shown here.

Odds & Ends Basket (select models)

Use this supplemental

basket in the upper rack

for loading miscellaneous

items and utensils. This is

also a safe place to load

sharp knives and pointed

items.

Cont.

Loading

Adjustable Rack [select models)

The Adjustable Upper Rack (select models) can be

raised or lowered to accommodate taller plates,

platters, pans, etc. optimizing useable space in both

upper and lower racks. Full size dinner plates can be

loaded in the upper rack if it is in the lower position.

Always adjust the upper rack before loading.

To lower the rack:

1. Pull the rack fully out.

Adjusters

2. Place thumbs on

each lever on

the adjuster

while holding

rack with hands.

3. Press down on

the levers with

thumbs and

push rack down. The rack will come to a stop when

it is in position.

To raise the rack:

1. Pull the rack fully out.

2. Place hands on both sides and lift up until rack

comes to a stop and latches in place.

Notes

• The dishwasher will not

operate correctly if the

wash arm is not aligned

with one of the water

inlet holes on back wall

of the dishwasher.

• The left and right side adjusters on the racks

must both be fully in the upward or downward

position for proper connection.

Removing the Upper Rack

The rack can be removed when tall or oversized items

need to be loaded into the lower rack. Unload the

rack before removing it from the dishwasher.

To remove rack with tab-lock rack stops:

1. Roll the rack '/3to '/2of the way out.

2. Locate the rack stops at the end of each track.

Squeeze the tab in the middle of the rack stop and

pull the rack stop straight out. Take care to support

the rack while removing the rack stops.

3. Roll the rack all

the way out of the

track and remove

from the

dishwasher.

To replace:

Style may vary by model

1. Replace the

dishwasher rack by guiding the

wheels into the tracks.

Tab Lock

Rack Stop

2. Push each rack stop squarely into the end of the

track until the catch pops into the small hole on the

side of the track.

6

DishwasherUse

Hot Water

For optimal cleaning and drying results, hot water

is necessary. The incoming water temperature

should be 120 ° F [49 ° C) to properly activate the

detergent and melt greasy food soils.

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run

into a glass in the sink. Place a candy thermometer in

the glass and check the temperature once it has

stopped rising.

Detergent

Use a detergent designed specifically for use in an

automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink).

Recommended Amount

Too little detergent results in poor cleaning, hard water

filming/spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness.

Suds can cause the dishwasher to overflow. Measure

the detergent carefully and use only detergents

designed for use in a dishwasher. Less detergent is

needed in soft water. Try another brand of detergent if

sudsing continues.

The amount of detergent to use is determined by the

hardness of the water and soil level of the load. Refer

to the following chart for detergent usage

recommendations.

Light Soil 2 tsp 6 tsp

Soft (0-4 gpg) Normal Soil /4tsp 6 tsp

Heavy Soil 4 tsp 7 tsp

Medium [5-9 gpg) Light Soil 4 tsp 6 tsp

Normal Soil 4 tsp 6 tsp

Heavy Soil 5 tsp 7 tsp

Hard (10-12 gpg) All Levels 5 tsp 8 tsp

*Your local water utility or state university extension service can tell

you the degree of water hardness in your area.

In extremely hard water conditions (13 grains per

gallon or more*), it is difficult to achieve good

results with any dishwasher. A mechanical water

softener may be necessary to improve water

quality, detergent effectiveness, and protect the

dishwasher parts from the damage that hard

water can cause.

Add recommended amount of detergent to each cup

as shown and close the detergent lid.

Do not use detergent with the Rinse Only (select

models) cycle. Leave the detergent lid open when

running Rinse Only (select models).

Rinse Aid

Regular use of a rinse aid improves drying,

reduces spotting and filming, and reduces

moisture left on the dishwasher interior.

An automatic rinse aid dispenser is located next to the

detergent cup.

The window next to the dispenser cap indicates when

the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser monthly.

To add rinse aid to the

dispenser, turn the cap

counterclockwise to open.

Remove the cap and pour

liquid rinse aid into the

opening. The amount of

rinse aid dispensed during

the cycle is adjustable by moving the lever inside the

reservoir area. For most water conditions use the

manufacturer recommended setting of"2". Adjust it up to

the "MAX" setting for hard water. Set the lever anywhere

between these amounts as needed to get the best results.

Replace the cap and turn it clockwise to close.

7

Cvcles,OptionsandLights

Cycles

Choose the cycle that best describes your dishload by pressing the corresponding touchpad. (See page 3,

Operating Tips, for how to begin the cycle).

Heavy Wash Long cycle for heavy food soils. 132 2 washes/3 rinses

Medium cycle for average food

Normal Wash soils. Precision CleanTM Turbidity 97-117 1-2 washes*/1-2 rinses*

sensor is active with this cycle.

Light Wash Short cycle for light food soils. 82 1 wash/2 rinses

Designed to select the number

Auto Clean of water fills best suited for the

soil level of each load. Precision 94-128 1-2 washes*/2-3 rinses*

(select models) CleanTM Turbidity sensor is active

with this cycle.

Rinses dishes being held until 9 1 rinse

Rinse Only there is a full load.

Insta-Wash Quick cycle for light food soils. 38 1 wash/2 rinses

(select models) Does not include drying time.

Numberof fillswill vary dependingonthesoil levelofeach load.

Notes

• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

• Cycle times shown in the numerical display (select models) will increase or decrease, based on each load's soil

level, water temperature and selected options.

• Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 184 Residential

Dishwashe0 for sanitization: Auto Clean (select models), Heavy Wash, Normal Wash and Light Wash.

8

Cycles,OptionsnndLights

Options

In addition to choosing a cycle from page 7,choose as many available options as are needed for your dishload.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii ii ! !i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i i Liiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii i i! i !iii i j i

Hi Temp Wash Hi Temp Wash provides additional heat during the wash portion All cycles

(select models) of the cycle, which ensures proper water temperature for better (except Rinse Only

cleaning and drying results. It also adds an additional rinse to [select models])

the cycle which improves results in hard water situations.

ToughScrubZM/ Selected when washing loads with hard-to-remove food soils. Heavy Wash

ToughScruh TM Plus Depending on which cycle is being used, this option adds Normal Wash

(select models) heat and/or wash time to the wash cycle. Light Wash

Auto Clean (selectmodels]

Sanitize

(select models)

160 ° Wash

(select models)

Heated Dry

Sanitizes dishware. When cycle monitor recognizes that the

proper conditions have been met, Sanitized light will activate

at the end of the cycle. Sanitization may not be achieved if

there is an interruption of the cycle, power failure or if the

incoming water temperature is below 120° F [49° C].

Raises temperature in the final rinse to 160° E This option can

be used with any cycle except Insta-Wash (select models)

and Rinse Only.

For enhanced drying results select this option. When Heated

Dry is not selected, towel drying of some items such as plastic

and items with non-stick surfaces may be necessary and more

moisture may be noticed adhering to the dishwasher interior.

In models with plastic interiors, it is normal to notice vapor

escaping from the door vent as the heat dries your dishes.

Vapor will escape even if Heated Dry is not selected.

Heavy Wash*

Normal Wash*

Light Wash*

Auto Clean* (selectmodels)

Heavy Wash

Normal Wash

Auto Clean* (selectmodels]

All cycles

(except Rinse Only)

StartJCancel Starts and stops dishwasher. See page 3 under Operating Tips: All Cycles

Operating the Dishwasher, for explanation.

Used to automatically start the cycle at a later time. See page 10 All Cycles

Delay for instructions.

Control Lock Option Locks control touchpad to prevent unwanted use. See page 10 All Cycles

(select models) for instructions.

Onlythese cycles havebeendesignatedto meetNSFrequirements(NSF/ANSI18/4ResidentialDishwasher)for sanitization.

9

Cycles,Options(andLights

Lights/Display

Delay

The Delay option can be used to automatically start

the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced

energy costs if available in your area. This option is

also useful for conserving hot water at times of high

household usage (showers, laundry).

To set up a Delay:

1. Select the appropriate cycle and options for the

load. Close the door.

.

Press the Delay pad until the desired amount of

delay time is selected.

3. The Delay indicator and the count down display

(select models) will flash until the START/Cancel

pad is pressed.

4. As soon as the START/Cancel pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Delay indicator will remain lit

until the delay time has counted down.

.

The cycle will automatically start as soon as the

delay time expires.

Control Lock

Option (select models)

The control touchpads can be locked to prevent

unwanted use. If this feature is activated between

cycles, the dishwasher cannot be operated until the

controls are unlocked. If desired, the controls can be

locked after a cycle or delay has started.

Setting the Control Lock:

1. Press the Heated Dry pad for three seconds.

2. An indicator light next to the lock graphic will

illuminate when the controls are locked.

To Cancel:

1. Press the Heated Dry pad for three seconds.

2. The indicator light will go off.

Notes

• If a cycle or option pad is pressed after the

controls have been locked, the indicator light next

to the lock graphic will flash five times. On

selected models with a countdown display, the

display will flash an "L" simultaneously with the

lock indicator.

• This option does not lock the door, only the

dishwasher controls.

Note

• If 30 seconds elapse between setting the cycle

and options and pressing the START/Cancel

pad, the dishwasher will turn off.

To cancel a Delay:

When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will

start or resume immediately.

To cancel a Delay and the cycle:

• Press START/Cancel once to drain and turn off the

dishwasher.

Or

• Press START/Cancel twice to turn dishwasher off

without draining.

10

Cycles,OptionsnndLights

Lights/Display (select models)

Time Remaining Display

(select models)

Clean Light

Drying Light

(select models)

Washing Light

(select models)

Heating Delay Light

(select models)

Sanitized Light

(select models)

Shows approximate minutes remaining in a cycle. The symbol "2H" will appear when

cycle time is greater than 99 minutes. Cycle times shown in the numerical display

(select models) will increase or decrease, based on each load's soil level, water

temperature and selected options.

Illuminates at the end of the cycle and remains lit until the door has been open for 30

seconds continuously.

Illuminates during the entire dry period and goes out when the cycle is completed.

Illuminates during all rinse and wash portions of the cycle.

Illuminates when cycle is being extended to heat the water.

Illuminates at the end of the cycle when conditions have been met to achieve

sanitization. The light will remain lit until the door has been open for 30 seconds

continuously.

Notes

• When Sanitize is selected, cycles are monitored to assure sanitization. The Sanitized light will not activate if

sanitization requirements are not met. This could happen if the cycle is interrupted, power failure occurs or

incoming water temperature is below 120° F (/49° F).

• The Clean and Sanitized indicator lights (select models) will not relight after a power failure until after the next cycle

is run.

11

CareandCleaning

General Recommendations

• The dishwasher interior is normally self-cleaning.

Periodically check the bottom of the dishwasher tub

to see if any large particles remain.

• Wipe the edge of the inner door liner to remove any

food soil splashes which occurred during loading.

• When cleaning stainless steel, always wipe with the

grain. Never use products containing chlorine bleach

or citric acid.

• The color from some tomato-based food soils may

occasionally adhere to various components of the

dishwasher interior, causing temporary discoloration.

To minimize this:

• Remove excess tomato-based food soils from dishes,

before loading.

• Run the Heavy Wash cycle when washing loads

containing tomato-based food soils.

• Use a dishwasher detergent that contains chlorine to

better fight staining.

Standard Exterior Light to moderate Soft damp cloth and liquid spray cleaner.

Daily cleaning and light soil

Stainless Steel

Exterior

(select models)

Moderate to heavy soil

Streaks or fingerprints/restore shine

Discoloration

Interior Light to moderate

Discoloration, or tomato-based stain

*Brand names are trademarks of the respective manufacturer.

**Call 1-877-232-6771 to order.

Do Not use abrasive powders or cleaning pads.

Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula 409 Glass and Surface Cleaner*, or

similar multi-surface cleaner.

• Do Not use products containing chlorine

bleach or citric acid.

Follow with rinse and dry.

Soft cloth or damp sponge and Bon Ami*.

Follow with rinse and dry.

Soft cloth and Stainless Steel Magic Spray**.

Soft cloth or damp sponge and Cameo Stainless

Steel Cleaner*. Rinse immediately and dry.

Soft cloth or damp sponge.

Switch dishwasher detergent to chlorine-based

product.

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher

detergent or baking soda and select the Normal Wash

cycle. Allow the dishwasher to complete the cycle. Then

turn the water supply off and drain the dishwasher. To

drain, press the START/Cancel pad once to activate

the dishwasher. Press START/Cancel again to activate

the drain. Operate the drain twice to ensure most of the

water is removed. Last, disconnect the electrical supply

and prop open the door.

When turning the water supply to the home off, the

water shut off at the dishwasher must be turned off also.

12

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.

Dishwasher will not fill • Press the START/Cancel pad to start the dishwasher.

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home's circuit breaker or fuse box.

• Check inlet hose for a kink.

• Check water valve inlet for sediment and clean if necessary.

Dishwasher will not drain/ • If hooked up to a food waste disposer, be sure the knock-out is removed from the

water in tub bottom disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home's circuit breaker or fuse box.

• Check that the cycle is completed.

Dishwasher adds water at • This is normal. The sensor (select models) in the pump must stay submerged so a

end of cycle short fill of water is added after the cycle's last drain.

Detergent cup is not empty " Check that the cycle is completed.

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place.

Dishwasher seems noisy • A water valve hiss during fill is normal.

• Water circulation sounds are normal.

• A thumping sound may be a wash arm bumping an item that is extending beyond the

racks. Readjust load to avoid obstructing wash arm.

• Chopping or grinding sounds may be heard as the internal chopper blade chops hard

items like fruit seeds, nuts, etc.

• Humming during the drain is normal.

• A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of the cycle. This is normal.

• Proper installation affects the noise level.

Cycle takes too long • ToughScrubT% ToughScrub TM Plus or Sanitized (select models) has been selected

and the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49° C).

Dishwasher has an odor • Run dishes being held in the dishwasher through a Rinse Only cycle (select models).

• Many dishwashers have a "new" smell when first installed. This will dissipate with use.

• Dishwasher may not be draining properly. (See "Dishwasher Will Not Drain" section.)

• For a strong odor, place baking soda in both sides of the detergent cup. Select Light

Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle

by unlatching the door and let it stand overnight. Restart the dishwasher by latching

the door and allow it to complete the cycle. Another alternative is to use a dishwasher

cleaning product such as Jet-Dry Dishwasher Cleaner*.

Dishwasher leaks • Check that the dishwasher is level. (Refer to the Installation Instructions.)

• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use

only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Try another brand of detergent if sudsing continues.

• Follow directions closely on how to add a forgotten item (log.3).

• Toavoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

Indicator lights flashing • The countdown display (select models) flashes after a cycle is selected until the

START/Cancel pad is pressed.

• The countdown display (select models) and the delay indicator flash after a delay is

selected until the START/Cancel pad is pressed.

• All active display indicators flash if the door is opened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after

cycle "lock-in".

• The lock indicator flashes and the countdown display (selected models) flashes an "L"

if a pad is pressed while the control lock is enabled.

13 Cont.

*Brand names are trademarks of the respective manufacturer.

Display time drops • Thisis normal when the Auto Clean (select models) or Normal Wash cycle isselected and

the dishwasher decides to skip or add a drain and refill.

Select Hi Temp Wash option.

Check water temperature. Incoming water should be 120° F (49° C).

Always use a rinse aid.

Confirm that the cloudiness is removable by soaking the item in white vinegar for

approximately 5 minutes. If removed, the problem is due to hard water. Adjust detergent

amount being used to match water hardness (pg. 7). Be sure detergent is fresh, stored

properly and is a high quality brand.

If cloudiness is not removable, it is etching. This is an erosion of the surface of the glassware

and can be caused by water that is too hot, from using too much detergent or by

prewashing. Detergent needs food soil to act upon. If etching has occurred, the glassware is

permanently damaged. To prevent further etching, adjust the detergent amount to match

the water hardness, stop prewashing, and use water heating options only when incoming

water temperature is below 120° F (49° C).

Check water temperature. Incoming water should be 120° F (49° C).

Run [lot water at the sink before starting the dishwasher.

Check water hardness and adjust detergent amount accordingly (pg. 7).

Use fresh detergent stored in a cool dry place.

Select proper cycle for the soil level (pg. 8).

Select proper option, ToughScrub TM, ToughSerubTM Plus or Hi Temp Wash (select models).

Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet

holes (pg. 6).

Load items so they do not block the wash arms (pgs. 3-6).

Load the utensil basket with knife handles up and spoon and fork handles down.

Do not place glasses over tines.

Before loading, scrape off burnt on foods and wipe the starchy film from utensils used with

pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.

Aluminum utensils or pans carl leave marks when they rub against other items. Leavea

slight space between items.

Iron deposits in the water carl leave a yellow, brown or orange film on dishes or the

dishwasher tub. A rust filter may be needed. Check with a water treatment company.

Separate silver or silver-plated silverware from stainless steel. These metals can be damaged

by contact with each other during washing.

Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. 12). If light

staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher

detergent that contains chlorine to better fight staining.

Certain dishwasher detergents may stain silver. Try another brand of detergent.

Be sure Heated Dry is selected.

Water droplets may form on the inner door as part of the drying process.

Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid* regularly, to

improve drying. Turn the rinse aid selector toward the MAX setting.

Check water temperature. Incoming water should be 120° F (49° C).

Select Sanitize option.

Increase detergent amount to match water hardness (pg. 7).

Load properly. (pgs. 3-6)

Plastic and items with non-stick surfaces are difficult to dry because they have a porous

surface which tends to collect water droplets. Towel drying may be necessary.

Glasses and cups with concave bottoms hold water and require towel drying. Locate these

items on the more slanted side of the rack for improved results.

Load dishes according to instructions so they do not strike each other (pgs. 3-6).

Washing fine antique china/crystal in the dishwasher is not recommended.

Do not load glasses over the tines.

Do not overload.

Sanitize was not selected.

Sanitization can only be achieved with the Auto Clean (select models), HeavyWash, Normal

Wash or Light Wash cycles.

Sanitization may not be achieved if there is an interruption of the cycle, power failure or if

incoming water temperature is below 120° F (49° C).

or increases (:selectmodels)

Glasses are cloudy/ •

spotted

Food soil remains

on dishes

Items washed in the "

dishwasher or the •

dishwasher tub itself

are stained/discolored "

Items not properly

dried/moisture is

present on the

dishwasher interior

after the dry cycle

Dishware is chipped •

Sanitized light does not "

illuminate at the end of "

the cycle (:select

models)

Dishwasher door will • Be sure adjustable racks (select models) are properly adjusted to upper or lower position

not close (pg. 6).

•Brandnamesaretrademarksof the respectivemanufacturer.

14

Wurrum¥u,d Service

CUSTOMER'S SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. IMPLIED

WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE,ARE LIMITED

TO ONE YEAR ORTHE SHORTEST

PERIODALLOWED BY LAW. MAYTAG

CORPORATION SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATESAND

PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE

DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS,SO

THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TOYOU. THIS

WARRANTY GIVESYOU SPECIFICLEGAL

RIGHTSAND YOU MAY ALSO HAVE

OTHER RIGHTS,WHICH VARY STATETO

STATEOR PROVINCE TO PROVINCE.

What is Not Covered By These Warranties

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents, unreasonable use, or acts of God.

d. Incorrect electric current, voltage, electrical and/or gas supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers [lave been removed, altered,

or cannot be readily determined.

3. Light bulbs, water filters and air filters.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors. For products requiring ventilation, rigid metal

ducting must be used.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to and from the servicer.

6. Any food loss due to refrigerator or freezer product failures.

Z Expenses for travel and transportation for product service in remote locations.

8. Outside of the United States and Canada this warranty does not apply.

Contact your dealer to determine if another warranty applies.

9. Consequential or incidental damages sustained by any person as a result of

any breach of these warranties. Some states do not allow the exclusion or

limitation of consequential or incidental damages, so the above exclusion may

not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the

dealer from whom your appliance was purchased or call Maytag Services, LLC,

Customer Assistance at 1-800-688-9900 USA and 1-800-688-2002 Canadato

locate an authorized servicer.

• Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY

for further information on owner's responsibilities for warranty service.

• If the dealer or service company cannot resolve the problem, write to Maytag

Services, LLC,Attn: CAIR" Center, RO. Box 2370,Cleveland,TN 37320-2370,or call

1-800-688-9900 USA and 1-800-688-2002 Canada. U.S.customers using

TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

• User's guides, service manuals and parts information are available from Maytag

Services, LLC,Customer Assistance.

Notes: When writing or calling about a service problem, please include:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or servicer;

d. A clear description of the problem you are having;

e. Proof of purchase (sales receipt).

15

Page is loading ...

Maytag MDB6701AWW - BI DW 5LVL SANI ESTAR Owner's manual

Maytag MDB6701AWW - BI DW 5LVL SANI ESTAR Owner's manual

in other languages

Related papers

Other documents