Performance is everything.
vax.co.uk
User Guide
W87-RP-C
Rapide
Deluxe
Pre-Treatment
Contents
Machine Overview
General Safety Information
Getting Started
How To Use
Looking After Your Machine
FAQs
Other Information
Guarantee
Contents
1
2
3
4
5
8
10
11
12
vax.co.uk
1
8
7
6
4
5
11
20
13
3
19
14
15
12
22
1
17
16
19
23
21
22
18
Machine Overview
2vax.co.uk
NOTE: Some parts may vary according to model. Please check inside ap of box for more details.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Handle
Clean water tank latch
Clean water tank
Dirty water tank latch
Dirty water tank handle
Rotating brush bar
Dirty water tank
Dirty water tank lid
On/o switch
Handle screw
Power cord
Carrying handle
Handle release pedal
Cord hook
Solution spray trigger (hidden)
Upholstery water supply plug
Upholstery hose adaptor
Upholstery hose
Upholstery attachement tool
Water supply socket
Pre-treatment wand
Pre-treatment solution
Vax carpet cleaner solution
10
9
2
This carpet washer is intended for household use only and NOT for commercial or industrial use.
Please keep instructions for further use.
When using the carpet washer, basic safety precautions should always be observed, including the following:
1. Do not leave the carpet washer unattended when plugged in. Unplug the appliance from the socket when not in use.
2. Only use the carpet washer indoors.
3. Turn o all controls on the carpet washer before disconnecting or connecting from the mains supply.
4. Always unplug the carpet washer before connecting or disconnecting the hose and accessories.
5. Always unplug the carpet washer before carrying out any maintenance.
6. Children should be supervised to ensure that they do not play with the appliance.
7. This appliance is not intended for use by children under eight years of age and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance in a safe way and understands the hazards involved.
8. Cleaning and maintenance shall not be made by children without supervision.
9. The appliance should only be used as described in the quick start guide or in the full online user guide.
10. Only Vax recommended solutions and attachments should be used with this appliance.
11. Do not use this carpet washer if it has been dropped, damaged, left outdoors or dropped into water. Do not use
this carpet washer with a damaged cord or plug. If the supply cord is damaged return the carpet washer
to a Vax Authorised Service Agent or contact our customer care centre.
12. Do not pull or carry this appliance by the cord. Do not use the cord as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the carpet washer over the cord. Keep the cord away from heated surfaces.
13. Do not handle the plug or the carpet washer with wet hands.
14. Keep hair, loose clothing, ngers and all parts of the body away from openings and moving parts.
15. Do not pick up with the machine any hot coals, cigarette butts, matches or any hot, smoking or burning objects.
16. Do not pick up with the machine any ammable or combustible materials (lighter uid, petrol, kerosene etc.) or use the
machine in the presence of explosive liquids or vapours.
17. Do not use the machine on areas where there may be harmful or toxic material (chlorine, bleach, ammonia,
drain cleaner etc.)
18. Store the carpet washer in a cool, dry area.
19. Do not use an extension cord with this machine.
20. Do not carry the appliance while it is switched on.
21. To prevent dirty water from running into the motor, do not hold the appliance upside-down or lay it on its side.
Use the appliance in a normal cleaning position.
22. Do not use without all water tanks and solution tanks in place.
23. Do not use the carpet washer unless the carpets have been dry vacuumed thoroughly rst.
24. Keep the unit on the oor.
25. Do not put any objects into openings. Do not use with any openings blocked and do not restrict airow. Keep all openings
free of dust, lint, hair or anything that might reduce airow.
26. Do not attempt to remove blockages with sharp objects as they may cause damage.
27. Using improper voltage may result in damage to the motor and possible injury to the user. The correct voltage is listed on
the rating label.
28. Do not use without all of the lters in place.
29. Take extra care when cleaning on the stairs.
30. Keep the area you are cleaning well lit.
31. Do not unplug the machine by pulling on the cord.
General Safety Information
vax.co.uk
3
Getting Started
PLEASE READ SAFETY INFORMATION BEFORE USE (p3)
Assemble the mid section onto the base. Insert two nuts into the recesses located
on the left and right sides of the base.
Hold the nuts in place and insert the two
medium length screws through the front
of the mid section and tighten.
Assembling your carpet washer handle
Slide the handle onto the unit. Insert
the nut into the recess in the back of
the handle. Hold the nut in place and
insert the long screw through the front
of the handle and tighten.
Assembling your tool caddy
Align tabs on tool caddy with
slots on midsection and snap
into place.
Slide the adapter end of the
hose into the left slot on the
lower tool caddy.
Lock the hose into place by
pressing down onto the post
until secure.
Place nut into recess on tool
caddy and hold into place.
Press handle release and tilt
the midsection backwards.
Place screw through
the centre of the lower
midsection and tighten.
Assembling your hose
CAUTION: The carpet washer is a very powerful unit. Before plugging the cord into the electric outlet, make sure all controls on the unit are turned
o. Hold the carpet washer rmly when starting and in use.
4vax.co.uk
vax.co.uk
5
Before you begin cleaning
Operating your pre-treatment wand
Pre-treating your carpet before washing will help to remove stubborn stains. Do not saturate your carpet.
Mix the solution with warm
water (max 40 C) and ll
tank with solution.
Remove clean water tank.
Tighten cap before
returning tank to unit.
Place the clean water tank
back on the carpet cleaner.
Attach the pre-treatment tube
to the water supply port.
Turn clockwise to secure.
Unwrap power cord,
plug unit in and turn
the on/o switch.
Using the wand and trigger,
apply the pre-treatment
solution to your carpets.
Spray evenly onto desired
areas and leave for 10-15
minutes before washing.
O
Pour required dose of pre
treatment solution (approx.
40ml per 1.0L of water.)
Do not saturate your carpet.
• Test for colourfastness – Wet a white absorbent cloth with the solution. In a small, hidden area of your carpet, gently rub the
surface with the dampened cloth. Wait ten minutes and check for colour removal or bleed with white paper towel or cloth. If your
carpet has more than one colour, check all colours.
• When cleaning an entire room, move furniture out of the area to be cleaned. If the furniture is too heavy to move, place aluminium
foil or wax paper under legs. This will prevent wood nishes from staining your carpet. Pin up furniture skirts and curtains.
IMPORTANT: Carpets should be dry vacuumed thoroughly before washing.
IMPORTANT: Only use Vax carpet cleaning solution. Using other solutions may cause excess foaming. Excessive foam will prevent
the machine from working eectively. Using other solutions will invalidate the guarantee.
6vax.co.uk
How To Use
IMPORTANT: Before setting the machine up to wash, ensure the clean water tank is rinsed thoroughly of
pre-treatment solution.
Mix the solution with warm
water (max 40 C) and ll
tank with solution.
Remove clean water tank.
Tighten cap before
returning tank to unit.
Place the clean water tank
back on the carpet cleaner.
Operating your carpet washer
Your dirty water tank is tted with a oat. When the dirty water tank is full or the oor head is not in contact with the carpet
the oat will shut o the suction at the oor nozzle. You will be able to hear if this has happened as the motor noise on the unit
will increase. Once the oat is activated, empty the dirty water tank if full. If the dirty water tank is not full then turn o your
machine at the power switch and wait for the oat to settle before re-starting.
When machine is reclined
brushbar will power.
Upright position brushbar
will not power.
Turn the power and brush
bar switches on.
Press trigger to
release solution.
For best results apply
solution on the forward
stroke and release the
trigger to recover solution
on the backward stroke.
O
Pour required dose of carpet
cleaning solution (approx.
40ml per 1.0L of water.)
Press on the handle release
pedal and pull the cleaner
back into a reclined position.
Unwrap power cord
and plug unit in.
vax.co.uk
7
How To Use
Remove hose.
Remove tank door from the
top of the dirty water tank.
Insert the hose adapter
into the top of the dirty
water tank.
Connect the hose water
supply plug into the socket
on the lower left side of
the cleaner. Align inserts
and push in. Turn clockwise
to secure.
Using the wash tool
Do not saturate your upholstery.
The clean water tank will need to be lled with Vax carpet cleaning solution and water before use.
Press trigger to
release solution.
For best results apply
solution on the forward
stroke and release the
trigger to recover on the
backward stroke.
8vax.co.uk
Looking After Your Machine
Empty the water tank by
grasping the handle with
one hand and nozzle with
the other and empty into
the sink.
NOTE: Rinse out tank with clean water and leave to air dry before storing your machine.
Threads caught in the
brushbar can be cut.
WARNING: Always switch o and unplug the carpet washer from the electrical outlet before assembling, lling and emptying
the clean water tank, emptying the dirty water tank, or before connecting/disconnecting the attachments.
Emptying the dirty water tank
1
2
Removing blockages from the brushbar
Grasp the handle and pull up
out of the base, take care to
ensure that no dirty water
leaks from the front.
Grasp the top of the dirty
water tank handle and press
the release latch.
Remove dirty water tank lid.
WARNING: Always switch o and unplug the carpet washer from the electrical outlet before assembling, lling and emptying
the clean water tank, emptying the dirty water tank, or before connecting/disconnecting the attachments.
vax.co.uk
7
vax.co.uk
9
Looking After Your Machine
Replacing the belt
Cleaning the lter
To remove the belt cover,
use a phillips screwdriver
to remove the two screws.
Grasp the brush bar with
one hand, using the other
hand to keep tension on the
belt while removing by lifting
upwards.
Slide the belt o the motor
shaft and dispose.
Rinse the lter with warm
water. Allow it to dry fully
before replacing it in
your cleaner.
Replace new belt on to
spindles and secure the
belt cover.
Replace the belt cover
inserting the end furthest
from the brush rst.
Then replace the front of the
belt cover before securing in
place with the two screws.
IMPORTANT: Cleaning lters maintains cleaning performance. For best cleaning results lters require cleaning at least every
three months. If your lters are washable make sure that they are completely dry before inserting them back into the cleaner.
IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the unit should overheat, the thermostat
will automatically turn the unit o. Should this occur, unplug the carpet washer from the electrical outlet and and turn o the switch.
Check the hose for blockages. Clean the lters. Allow the unit to cool for approximately one hour (if you have cleaned the lters
you will need to wait twenty four hours for the lters to dry before putting them back in the machine.) To re-start the machine,
plug it into an electrical outlet and switch it back on.
WARNING: To reduce the risk of electric shock, turn the machine o and unplug from electrical socket before performing
maintenance/troubleshooting checks.
WARNING: Always switch o and unplug the carpet washer from the electrical outlet before assembling,
lling and emptying the clean water tank, emptying the dirty water tank, or before connecting/disconnecting
the attachments.
8vax.co.uk
FAQs
10vax.co.uk
Is there an accessory missing?
•Checkthe‘Thispackcontains’panelontheboxtomakesurethepartisdenitelyincludedinyourunit.
Why won’t the carpet washer turn on?
•Itmaynotbepluggedintotheelectricalsocketcorrectly:ensurethattheplugispushedinsecurelyandswitchedon.
•Thepowerbuttonontheunithasn’tbeenfullydepressed.
•Ifunitcutsoutduringuse,disconnecttheunitfromtheelectricalsocket,allowtocoolforonehour,cleanthelterandempty
the dirty water tank and check hose, brushbar for blockages.
Why won’t the cleaner pick up solution/spills?
•Theoatinthedirtywatertankmayhavebeenactivated.Emptythedirtywatertankiffull.Ifthedirtywatertankisnotfull
then switch the machine o and wait for the oat to settle before re-starting your machine.
•Thedirtywatertankmaybefullandtheautoshutoengaged.Emptythedirtywatertank.
•Ensurethedirtywatertankisttedcorrectlyandthetankcapissecurelytted.
•Checkthehoseforblockages.
•Checkthebrushbarforblockages.
Why won’t the solution/clean water dispense?
•Ensurethecleanwatertankisttedsecurely.
•Thesolution/cleanwatertankmaybeempty.
•Ensuredirtywatertankisttedsecurely.
Why won’t the brushes rotate?
•Thebrusheswillonlyrotatewhentheunitisreclinedandturnedon.
•Checktheoatchamberlterandcleanifnecessary.
•Beltmaybebroken–replaceifnecessary.
UK Service & Help
Any queries or concerns about using your Vax, simply visit; vax.co.uk/support – vaxireland.ie or call the
Vax Careline. Calls are charged at the UK local rate. Please make a note of the serial number and model
number of the vacuum cleaner before calling.
Vax Careline:
(UK) 0844 412 8455
(ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm
Saturday 9.00am to 5.00pm
Consumables
To purchase spares and accessories, please visit vax.co.uk
The use of genuine vax spare parts helps to maintain optimised
performance and validates your guarantee
Float chamber lter kit: 1-9-130494-00
Belt kit – Type 16: 1-9-130510-00
Technical Specication
Voltage: 220-240V ~50Hz
Wattage: 600W
Capacity: Clean water tank 3.5L
Dirty water tank 2.0L
Cord length: 7.5m
Weight: 7.7kg
Filter: Float chamber lter
Subject to technical change without notice.
EEC Statement of Compliance
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the Rapide Deluxe
series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Machine Overview
vax.co.uk
11
Other Information
Guarantee
FREE 2 year guarantee
Instead of taking me back to the shop, simply visit:
vax.co.uk/support or call (UK) 0844 412 8455 (ROI) 1-800 928 308
Let us know what you think @VaxUK
we’re here if you need us
UK based customer care centre — Open 6 days a week
Monday-Friday 8:30am-18:30pm
Saturday 9:00am-17:00pm
Please retain your original receipt for proof of purchase.
It’s quick and easy to register for your
online at: vax.co.uk/guarantees
Guarantee
12vax.co.uk
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: inf[email protected] website: vax.co.uk
Performance is everything.
vax.co.uk
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Vax Rapide Ultimate W87-RH-P User manual
-
Vax POWERMAX Owner's manual
-
Vax Rapide XL Pro User manual
-
-
-
-
-
-
-
Vax POWERMAX User manual
