Marantz M-ER803 Owner's manual

Brand: Marantz

Model: M-ER803

Category: Blu-Ray players

Type: Owner's manual

Blu-ray Disc Receiver

M-ER803

SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH

Page is loading ...

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

To completely disconnect this product from the mains, disconnect

the plug from the wall socket outlet.

The mains plug is used to completely interrupt the power supply to

the unit and must be within easy access by the user.

VORSICHT:

Um dieses Gerät vollständig von der Stromversorgung abzutrennen,

ziehen Sie bitte den Stecker aus der Wandsteckdose.

Der Netzstecker wird verwendet, um die Stromversorgung zum

Gerät völlig zu unterbrechen; er muss für den Benutzer gut und

einfach zu erreichen sein.

PRECAUTION:

Pour déconnecter complètement ce produit du courant secteur,

débranchez la prise de la prise murale.

La prise secteur est utilisée pour couper complètement

l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder

facilement.

ATTENZIONE:

Per scollegare completamente questo prodotto dalla rete di

alimentazione elettrica, scollegare la spina dalla relativa presa a

muro.

La spina di rete viene utilizzata per interrompere completamente

l’alimentazione all’unità e deve essere facilmente accessibile

all’utente.

WAARSCHUWING:

Om de voeding van dit product volledig te onderbreken moet de

stekker uit het stopcontact worden getrokken.

De netstekker wordt gebruikt om de stroomtoevoer naar het toestel

volledig te onderbreken en moet voor de gebruiker gemakkelijk

bereikbaar zijn.

FÖRSIKTIHETSMÅTT:

Koppla loss stickproppen från eluttaget för att helt skilja produkten

från nätet.

Stickproppen används för att helt bryta strömförsörjningen till

apparaten, och den måste vara lättillgänglig för användaren.

PRECAUCIÓN:

Para desconectar completamente este producto de la alimentación

eléctrica, desconecte el enchufe del enchufe de la pared.

El enchufe de la alimentación eléctrica se utiliza para interrumpir

por completo el suministro de alimentación eléctrica a la unidad

y debe de encontrarse en un lugar al que el usuario tenga fácil

acceso.

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.

UNDGÅ UDSAETTELSE FOR STRÅLING.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ

KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA

ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1

YLITTÄVÄLLE NÄKYMÄMTTÖMÄLLE LASERSÄTEILYLLE.

VARNING: OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA

BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN

UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING SOM

ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

ATTENZIONE: QUESTO APPARECCHIO E’ DOTATO DI

DISPOSITIVO OTTICO CON RAGGIO LASER.

L’USO IMPROPRIO DELL’APPARECCHIO PUO’ CAUSARE

PERICOLOSE ESPOSIZIONI A RADIAZIONI!

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE

EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFETY

INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

10. Only use attachments/accessories speciﬁed by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when

unused for long periods of time.

13. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

14. Batteries shall not be exposed to excessive heat such as sunshine, ﬁre or

the like.

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO /

NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA ANGÅENDE ANVÄNDNINGEN

WARNINGS WARNHINWEISE AVERTISSEMENTS AVVERTENZE ADVERTENCIAS WAARSCHUWINGEN VARNINGAR

• Avoid high temperatures.

Allow for sufﬁcient heat

dispersion when installed in a

rack.

• Handle the power cord carefully.

Hold the plug when unplugging

the cord.

• Keep the unit free from

moisture, water, and dust.

• Unplug the power cord when

not using the unit for long

periods of time.

• Do not obstruct the ventilation

holes.

• Do not let foreign objects into

the unit.

• Do not let insecticides,

benzene, and thinner come in

contact with the unit.

• Never disassemble or modify

the unit in any way.

• Ventilation should not be

impeded by covering the

ventilation openings with

items, such as newspapers,

tablecloths or curtains.

• Naked ﬂame sources such as

lighted candles should not be

placed on the unit.

• Observe and follow local

regulations regarding battery

disposal.

• Do not expose the unit to

dripping or splashing ﬂuids.

• Do not place objects ﬁlled with

liquids, such as vases, on the

unit.

• Do not handle the mains cord

with wet hands.

• When the switch is in the OFF

position, the equipment is not

completely switched off from

MAINS.

• The equipment shall be

installed near the power supply

so that the power supply is

easily accessible.

• Vermeiden Sie hohe Temperaturen.

Beachten Sie, dass eine

ausreichende Belüftung

gewährleistet wird, wenn das Gerät

auf ein Regal gestellt wird.

• Gehen Sie vorsichtig mit dem

Netzkabel um.

Halten Sie das Kabel am

Stecker, wenn Sie den Stecker

herausziehen.

• Halten Sie das Gerät von

Feuchtigkeit, Wasser und Staub

fern.

• Wenn das Gerät längere Zeit

nicht verwendet werden soll,

trennen Sie das Netzkabel vom

Netzstecker.

• Decken Sie den Lüftungsbereich

nicht ab.

• Lassen Sie keine fremden

Gegenstände in das Gerät

kommen.

• Lassen Sie das Gerät nicht

mit Insektiziden, Benzin oder

Verdünnungsmitteln in Berührung

kommen.

• Versuchen Sie niemals das Gerät

auseinander zu nehmen oder zu

verändern.

• Die Belüftung sollte auf keinen

Fall durch das Abdecken der

Belüftungsöffnungen durch

Gegenstände wie beispielsweise

Zeitungen, Tischtücher, Vorhänge

o. Ä. behindert werden.

• Auf dem Gerät sollten keinerlei

direkte Feuerquellen wie

beispielsweise angezündete

Kerzen aufgestellt werden.

• Bitte beachten Sie bei der

Entsorgung der Batterien

die örtlich geltenden

Umweltbestimmungen.

• Das Gerät sollte keiner tropfenden

oder spritzenden Flüssigkeit

ausgesetzt werden.

• Auf dem Gerät sollten keine mit

Flüssigkeit gefüllten Behälter wie

beispielsweise Vasen aufgestellt

werden.

• Das Netzkabel nicht mit feuchten

oder nassen Händen anfassen.

• Wenn der Schalter ausgeschaltet

ist (OFF-Position), ist das Gerät

nicht vollständig vom Stromnetz

(MAINS) abgetrennt.

• Das Gerät sollte in der Nähe einer

Netzsteckdose aufgestellt werden,

damit es leicht an das Stromnetz

angeschlossen werden kann.

• Eviter des températures

élevées.

Tenir compte d’une dispersion

de chaleur sufﬁsante lors de

l’installation sur une étagère.

• Manipuler le cordon

d’alimentation avec précaution.

Tenir la prise lors du

débranchement du cordon.

• Protéger l’appareil contre

l’humidité, l’eau et la poussière.

• Débrancher le cordon

d’alimentation lorsque l’appareil

n’est pas utilisé pendant de

longues périodes.

• Ne pas obstruer les trous

d’aération.

• Ne pas laisser des objets

étrangers dans l’appareil.

• Ne pas mettre en contact des

insecticides, du benzène et un

diluant avec l’appareil.

• Ne jamais démonter ou

modiﬁer l’appareil d’une

manière ou d’une autre.

• Ne pas recouvrir les oriﬁ ces

de ventilation avec des objets

tels que des journaux, nappes

ou rideaux. Cela entraverait la

ventilation.

• Ne jamais placer de ﬂamme

nue sur l'appareil, notamment

des bougies allumées.

• Veillez à respecter les lois en

vigueur lorsque vous jetez les

piles usagées.

• L’appareil ne doit pas être

exposé à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant

du liquide, par exemple un

vase, sur l’appareil.

• Ne pas manipuler le cordon

d’alimentation avec les mains

mouillées.

• Lorsque l’interrupteur est sur

la position OFF, l’appareil n’est

pas complètement déconnecté

du SECTEUR (MAINS).

• L’appareil sera installé près de

la source d’alimentation, de

sorte que cette dernière soit

facilement accessible.

• Evitate di esporre l’unità a

temperature elevate.

Assicuratevi che vi sia

un’adeguata dispersione del

calore quando installate l’unità

in un mobile per componenti

audio.

• Manneggiate il cavo di

alimentazione con attenzione.

Tenete ferma la spina quando

scollegate il cavo dalla presa.

• Tenete l’unità lontana

dall’umidità, dall’acqua e dalla

polvere.

• Scollegate il cavo di

alimentazione quando

prevedete di non utilizzare

l’unità per un lungo periodo di

tempo.

• Non coprite i fori di

ventilazione.

• Non inserite corpi estranei

all’interno dell’unità.

• Assicuratevi che l’unità non

entri in contatto con insetticidi,

benzolo o solventi.

• Non smontate né modiﬁcate

l’unità in alcun modo.

• Le aperture di ventilazione

non devono essere ostruite

coprendole con oggetti, quali

giornali, tovaglie, tende e così

via.

• Non posizionate sull’unità ﬁ

amme libere, come ad esempio

candele accese.

• Prestate attenzione agli aspetti

legati alla tutela dell’ambiente

nello smaltimento delle

batterie.

• L’apparecchiatura non deve

essere esposta a gocciolii o

spruzzi.

• Non posizionate sull’unità alcun

oggetto contenente liquidi,

come ad esempio i vasi.

• Non toccare il cavo di

alimentazione con le mani

bagnate.

• Quando l’interruttore

è nella posizione OFF,

l’apparecchiatura non è

completamente scollegata da

MAINS.

• L’apparecchio va installato

in prossimità della fonte di

alimentazione, in modo che

quest’ultima sia facilmente

accessibile.

• Evite altas temperaturas.

Permite la suﬁciente dispersión

del calor cuando está instalado

en la consola.

• Maneje el cordón de energía

con cuidado.

Sostenga el enchufe cuando

desconecte el cordón de

energía.

• Mantenga el equipo libre de

humedad, agua y polvo.

• Desconecte el cordón de

energía cuando no utilice el

equipo por mucho tiempo.

• No obstruya los oriﬁcios de

ventilación.

• No deje objetos extraños

dentro del equipo.

• No permita el contacto

de insecticidas, gasolina y

diluyentes con el equipo.

• Nunca desarme o modiﬁque el

equipo de ninguna manera.

• La ventilación no debe quedar

obstruida por haberse cubierto

las aperturas con objetos

como periódicos, manteles o

cortinas.

• No deberán colocarse sobre

el aparato fuentes inﬂamables

sin protección, como velas

encendidas.

• A la hora de deshacerse de las

pilas, respete la normativa para

el cuidado del medio ambiente.

• No exponer el aparato al goteo

o salpicaduras cuando se

utilice.

• No colocar sobre el aparato

objetos llenos de líquido, como

jarros.

• No maneje el cable de

alimentación con las manos

mojadas.

• Cuando el interruptor está en la

posición OFF, el equipo no está

completamente desconectado

de la alimentación MAINS.

• El equipo se instalará cerca

de la fuente de alimentación

de manera que resulte fácil

acceder a ella.

• Vermijd hoge temperaturen.

Zorg er bij installatie in een

audiorack voor, dat de door het

toestel geproduceerde warmte

goed kan worden afgevoerd.

• Hanteer het netsnoer

voorzichtig.

Houd het snoer bij de stekker

vast wanneer deze moet

worden aan- of losgekoppeld.

• Laat geen vochtigheid,

water of stof in het apparaat

binnendringen.

• Neem altijd het netsnoer uit

het stopkontakt wanneer het

apparaat gedurende een lange

periode niet wordt gebruikt.

• De ventilatieopeningen mogen

niet worden beblokkeerd.

• Laat geen vreemde

voorwerpen in dit apparaat

vallen.

• Voorkom dat insecticiden,

benzeen of verfverdunner met

dit toestel in contact komen.

• Dit toestel mag niet

gedemonteerd of aangepast

worden.

• De ventilatie mag niet

worden belemmerd door

de ventilatieopeningen af

te dekken met bijvoorbeeld

kranten, een tafelkleed of

gordijnen.

• Plaats geen open vlammen,

bijvoorbeeld een brandende

kaars, op het apparaat.

• Houd u steeds aan de

milieuvoorschriften wanneer u

gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan

druppels of spatten.

• Plaats geen voorwerpen gevuld

met water, bijvoorbeeld een

vaas, op het apparaat.

• Raak het netsnoer niet met

natte handen aan.

• Als de schakelaar op OFF

staat, is het apparaat niet

volledig losgekoppeld van de

netspanning (MAINS).

• De apparatuur wordt in de

buurt van het stopcontact

geïnstalleerd, zodat dit altijd

gemakkelijk toegankelijk is.

• Undvik höga temperaturer.

Se till att det ﬁnns möjlighet

till god värmeavledning vid

montering i ett rack.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas

från el-uttaget.

• Utsätt inte apparaten för fukt,

vatten och damm.

• Koppla loss nätkabeln om

apparaten inte kommer att

användas i lång tid.

• Täpp inte till

ventilationsöppningarna.

• Se till att främmande föremål

inte tränger in i apparaten.

• Se till att inte insektsmedel

på spraybruk, bensen och

thinner kommer i kontakt med

apparatens hölje.

• Ta inte isär apparaten och

försök inte bygga om den.

• Ventilationen bör inte

förhindras genom att täcka

för ventilationsöppningarna

med föremål såsom tidningar,

bordsdukar eller gardiner.

• Placera inte öppen eld, t.ex.

tända ljus, på apparaten.

• Tänk på miljöaspekterna när du

bortskaffar batterier.

• Apparaten får inte utsättas för

vätska.

• Placera inte föremål fyllda

med vätska, t.ex. vaser, på

apparaten.

• Hantera inte nätsladden med

våta händer.

• Även om strömbrytaren står

i det avstängda läget OFF,

så är utrustningen inte helt

bortkopplad från det elektriska

nätet (MAINS).

• Utrustningen ska vara

installerad nära strömuttaget

så att strömförsörjningen är lätt

att tillgå.

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

III

A NOTE ABOUT RECYCLING:

This product’s packaging materials are recyclable and can be reused. Please

dispose of any materials in accordance with the local recycling regulations.

When discarding the unit, comply with local rules or regulations.

Batteries should never be thrown away or incinerated but disposed of in

accordance with the local regulations concerning battery disposal.

This product and the supplied accessories, excluding the batteries, constitute

the applicable product according to the WEEE directive.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist zum Recyceln geeignet und kann

wieder verwendet werden. Bitte entsorgen Sie alle Materialien entsprechend

der örtlichen Recycling-Vorschriften.

Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und

Bestimmungen.

Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden;

bitte entsorgen Sie die Batterien gemäß der örtlichen Vorschriften.

Dieses Produkt und das im Lieferumfang enthaltene Zubehör (mit Ausnahme

der Batterien!) entsprechen der WEEE-Direktive.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être

réutilisés. Veuillez disposer des matériaux conformément aux lois sur le recyclage

en vigueur.

Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations en vigueur.

Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux lois

en vigueur sur la mise au rebut des piles.

Ce produit et les accessoires inclus, à l’exception des piles, sont des produits conformes à la

directive DEEE.

NOTA RELATIVA AL RICICLAGGIO:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali

conformemente alle normative locali sul riciclaggio.

Per lo smaltimento dell’unità, osservare le normative o le leggi locali in vigore.

Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui

riﬁuti chimici.

Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad

eccezione delle batterie.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar.

Disponga de estos materiales siguiendo los reglamentos de reciclaje de su localidad.

Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.

Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos

de su localidad relacionados con los desperdicios químicos.

Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva

RAEE excepto pilas.

EEN AANTEKENING MET BETREKKING TOT DE RECYCLING:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt

verzocht om zich van elk afvalmateriaal te ontdoen volgens de plaatselijke voorschriften.

Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed

op.

Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke

voorschriften betreffende chemisch afval worden verwijderd.

Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor

afgedankte elektrische en elektronische apparaten (WEEE) van toepassing.

OBSERVERA ANGÅENDE ÅTERVINNING:

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala

återvinningsbestämmelser.

När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.

Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser

för kemiskt avfall.

Denna apparat och de tillbehör som levereras med den uppfyller gällande WEEE-direktiv, med

undantag av batterierna.

• DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, to which this

declaration relates, is in conformity with the following standards:

EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.

Following the provisions of Low Voltage Directive 2006/95/EC and EMC

Directive 2004/108/EC, the EC regulation 1275/2008 and its frame work

Directive 2009/125/EC for Energy-related Products (ErP).

• ÜBEREINSTIMMUNGSERKLÄRUNG

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das

sich diese Erklärung bezieht, den folgenden Standards entspricht:

EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.

Following the provisions of low voltage directive 2006/95/EC and EMC

directive 2004/108/EC, the EC regulation 1275/2008 and its frame work

directive 2009/125/EC for energy-related products (ErP).

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel se

réfère cette déclaration, est conforme aux standards suivants:

EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.

Selon la directive 2006/95/EC concernant la basse tension et la directive

CEM 2004/108/EC, la réglementation européenne 1275/2008 et la directive

2009/125/EC établissant un cadre de travail applicable aux produits liés à

l'énergie (ErP).

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la

nostra dichiarazione si riferisce, è conforme alle seguenti normative:

EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.

Facendo seguito alle disposizioni della direttiva sul basso voltaggio

2006/95/EC alla direttiva EMC 2004/108/EC, alla norma EC 1275/2008 e

alla relativa legge quadro 2009/125/EC in materia di prodotti alimentati ad

energia (ErP).

QUESTO PRODOTTO E’ CONFORME

AL D.M. 28/08/95 N. 548

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto al

que hace referencia esta declaración, está conforme con los siguientes

estándares:

EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.

De acuerdo con la directiva sobre baja tensión 2006/95/CE y la directiva

sobre CEM 2004/108/CE, la normativa CE 1275/2008 y su directiva marco

2009/125/EC para productos relacionados con la energía (ErP).

• EENVORMIGHEIDSVERKLARING

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt,

waarop deze verklaring betrekking heeft, in overeenstemming is met de

volgende normen:

EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.

Volgens de voorzieningen van lage spanningsrichtlijn 2006/95/EC en

EMC-richtlijn 2004/108/EC, de EU-richtlijn 1275/2008 en de kaderrichtlijn

2009/125/EC voor energieverbruikende producten (ErP).

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg

avser, uppfyller följande standarder:

EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.

Uppfyller reglerna i lågspänningsdirektivet 2006/95/EC och EMC-direktivet

2004/108/EC, EU-förordningen 1275/2008 och ramverksdirektivet

2009/125/EC för energirelaterade produkter (ErP).

Marantz Europe

A division of D&M Europe B.V.

Beemdstraat 11, 5653 MA Eindhoven,

The Netherlands

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

n CAUTIONS ON INSTALLATION

VORSICHTSHINWEISE ZUR AUFSTELLUNG

PRÉCAUTIONS D’INSTALLATION

PRECAUZIONI SULL’INSTALLAZIONE

EMPLAZAMIENTO DE LA INSTALACIÓN

VOORZORGSMAATREGELEN BIJ DE INSTALLATIE

FÖRSIKTIGHET VID INSTALLATIONEN

Wall

Wand

Paroi

Parete

Pared

Muur

Vägg

z z

z For proper heat dispersal, do not install this unit

in a conﬁned space, such as a bookcase or similar

enclosure.

• More than 0.3 m is recommended.

• Do not place any other equipment on this unit.

z Stellen Sie das Gerät nicht an einem geschlossenen

Ort, wie in einem Bücherregal oder einer ähnlichen

Einrichtung auf, da dies eine ausreichende Belüftung

des Geräts behindern könnte.

• Empfohlen wird über 0,3 m.

• Keine anderen Gegenstände auf das Gerät stellen.

z Pour permettre la dissipation de chaleur requise,

n’installez pas cette unité dans un espace conﬁné tel

qu’une bibliothèque ou un endroit similaire.

• Une distance de plus de 0,3 m est recommandée.

• Ne placez aucun matériel sur cet appareil.

z Per una dispersione adeguata del calore, non

installare questa apparecchiatura in uno spazio

ristretto, come ad esempio una libreria o simili.

• Si raccomanda una distanza superiore ai 0,3 m.

• Non posizionare alcun altro oggetto o dispositivo su

questo dispositivo.

z Para la dispersión del calor adecuadamente, no

instale este equipo en un lugar conﬁnado tal como

una librería o unidad similar.

• Se recomienda dejar más de 0,3 m alrededor.

• No coloque ningún otro equipo sobre la unidad.

z Plaats dit toestel niet in een kleine afgesloten ruimte,

zoals een boekenkast e.d., omdat anders de warmte

niet op gepaste wijze kan worden afgevoerd.

• Meer dan 0,3 m is aanbevolen.

• Plaats geen andere apparatuur op het toestel.

z För att tillförsäkra god värmeavledning får

utrustningen inte installeras i instängda utrymmen,

som t.ex. en bokhylla eller liknande.

• Mer än 0,3 m rekommenderas.

• Placera ingen annan utrustning ovanpå den här

enheten.

Page is loading ...

ENGLISH

Main features

High quality ampliﬁ er stressing sound quality

Equipped with a 70 W + 70 W (6 Ω) high-quality ampliﬁ er circuits.

Direct Play for iPod

and iPhone

via USB

Music data from an iPod can be played back if you connect the

USB cable supplied with the iPod via the USB port of this unit, and

also an iPod can be controlled with the remote control for this unit.

Weight and Dramatic sound

The board and circuit conﬁ guration has been redesigned to achieve

lower impedance. Since stable current is supplied to the power

amp and other sections, it is possible to realize as much as 70

watts of power.

“Simple & Straight” circuit design for sound

purity and free of coloration

This unit gives you high sound quality based on the “simple &

straight” concept. Circuitry is uncomplicated, signal paths are short,

and all adverse inﬂ uences on sound quality have been minimized.

Playback of MP3 and WMA ﬁ les

Supports playback of discs and USB memory devices on which

MP3 or WMA ﬁ les are recorded. The unit’s display can display the

title of the track and the name of the artist of the current track.

Low standby power consumption

Designed with the environment in mind, the unit consumes just

0.5 W while in standby mode.

M-XPort (Marantz-eXtension Port)

This unit is equipped with the M-XPort, a Marantz original innovation

that provides outstanding expandability. You can connect the

Wireless Receiver RX101 (sold separately) to this port.

Cautions on handling

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

• Power is supplied to some of the circuitry even when the unit is

set to the standby mode. When going on vacation or leaving home

for long periods of time, be sure to unplug the power cord from the

power outlet.

• Image persistence (image burn-in)

Do not leave the still images of the disc menu, the unit menu, etc.,

displayed on the TV screen for long periods. This can result in image

persistence (image burn-in) on the screen.

• About Condensation

If this unit is moved from a cold place to a warm place, or installed

in a room subject to rapid temperature rise from a heater, etc.,

condensation (dew) may form on the internal parts of the unit

(operating parts and lenses).

If used in this condition, this unit will not operate correctly and

damage may result. If condensation is formed on the unit, leave this

unit for 1 to 2 hours with the power off before use.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If that

occurs, move the mobile phone away from this unit when it is in use.

• Moving the unit

Be sure to remove a disc, turn off the power and unplug the power

cord from the power outlet. Next, disconnect the connection cables

to other system equipment before moving the unit.

• About Care

• Wipe the cabinet and control panel clean with a soft cloth.

• Follow the instructions when using a chemical cleaner.

• Benzene, paint thinner or other organic solvents as well as

insecticide may cause material changes and discoloration if brought

into contact with the unit, and should therefore not be used.

• Sufﬁ ciently ventilate the place of installation

If the unit is left in a room full of the smoke from cigarettes, etc., for

long periods of time, the surface of the optical pickup could get dirty,

in which case it will not be able to read the signals properly.

Accessories

Check that the following parts are supplied with the product.

q Remote control unit (RC001ER) .............................................. 1

w R03/AAA batteries ...................................................................2

e Power cord ..............................................................................1

r AM loop antenna .....................................................................1

t FM indoor antenna .................................................................. 1

y iPod stand ................................................................................1

u User guide ...............................................................................1

About this manual

n Operation buttons

The operations described in this guide are based mainly on remote

control operation.

n Symbols

This symbol indicates a reference page on which

related information is described.

This symbol indicates a supplementary information

and tips for operations.

NOTE

This symbol indicates points to remember operations

or function limitations.

n Illustrations

Note that the illustrations in this guide are for explanation purposes

and may differ from the actual unit.

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁcations Index

Getting

Started

ENGLISH

About discs

Inserting a disc

• Set the disc with the labeled side facing up.

• Make sure the disc tray is fully open when inserting the disc.

• Place the disc horizontally in the tray, aligned with the tray guide.

“NO DISC” is displayed if a disc that cannot be played back on this

unit is loaded and the disc tray reopens in the case of some discs.

NOTE

• Only load one disc at a time. Loading two or more discs can damage

the unit or scratch the discs.

• Do not use cracked or warped discs or discs that have been repaired

with adhesive, etc.

• Do not use discs on which the sticky part of cellophane tape or labels

is exposed or on which there are traces of where labels have been

removed. Such discs can get caught inside the player and damage it.

• Do not use discs with special shapes, as they could damage the

player.

• Do not push the disc tray in by hand when the power is turned off.

Doing so could damage the set.

Holding discs

Do not touch the signal surface.

Loading discs

• Place the disc in the tray, label side up.

• Make sure the disc tray is fully open when inserting the disc.

• Place the discs ﬂat, 12 cm discs in the outer tray guide (Figure 1), 8

cm discs in the inner tray guide (Figure 2).

12 cm disc

Outer tray guide

Figure 1

8 cm disc

Outer tray guide

Figure 2

• Place 8 cm discs in the inner tray guide without using an adapter.

“NO DISC” is displayed if the disc is loaded upside-down or if no disc

is loaded.

Cautions on handling

• Do not get ﬁngerprints, oil or dirt on discs.

• Take special care not to scratch discs when removing them from

their cases.

• Do not bend or heat discs.

• Do not enlarge the hole in the center.

• Do not write on the labeled (printed) surface with ball-point pens,

pencils, etc., or stick new labels on discs.

• Water droplets may form on discs if they are moved suddenly from

a cold place (outdoors for example) to a warm place, but do not try to

dry them off using a hairdryer, etc.

Cautions on storing discs

• Be sure to remove discs after using them.

• Be sure to store discs in their cases to protect them from dust,

scratches, warping, etc.

• Do not store discs in the following places:

1. Places exposed to direct sunlight for long periods of time

2. Dusty or humid places

3. Places exposed to heat from heaters, etc.

Cleaning discs

• If there are ﬁngerprints or dirt on a disc, wipe them off before using

the disc. Fingerprints and dirt can impair sound quality and cause

interruptions in playback.

• Use a commercially available disc cleaning set or a soft cloth to clean

discs.

Gently wipe the disc from the

inside towards the outside.

Do not wipe in a circular motion.

NOTE

Do not use record spray, antistatic agents, benzene, thinner or other

solvents.

ENGLISH

Power operation button

(ON/STANDBY) ······························(11, 12, 46)

w TIMER indicator ·········································· (39)

e Door

When you are using buttons and/or terminals

behind the door, press the bottom of the door

to open it. When not using buttons and/or

terminals behind the door, close it. Be careful

not to catch your ﬁ ngers when closing the door.

r Display ··························································· (5)

t Remote control sensor ································(7)

y Master volume control buttons

(VOLUME d,f) ············································ (13)

u Stop button (2) ······························ (11, 18, 22)

i Forward-skip/search button

(9) ················································ (19, 23, 46)

o Play/Pause button (1/3) ····················· (18, 40)

Q0 Disc tray open/close button (5) ················(16)

Q1 Reverse-skip/search button

(8) ················································ (19, 23, 46)

Q2 Disc tray ························································(3)

Q3 Input source select button (INPUT) ·········· (12)

Part names and functions

For buttons not explained here, see the page indicated in parentheses ( ).

Front panel

ye rq tw

Q5 Q3Q6 Q5 Q4 uiQ1 Q0 o

About discs

About discs and ﬁ les

n BD-Video, DVD-Video

BD-Video/DVD-Video discs are divided into several large sections

(titles) and small sections (chapter). These sections are all allotted

numbers, called the title numbers and chapter numbers.

GExampleH

Title1 Title2

Chapter 3

Blu-ray Disc, DVD

Chapter 2Chapter 1Chapter 2Chapter 1

n CD

CDs are divided into several sections (tracks). These sections are

all allotted numbers, called the track numbers.

Track1 Track2 Track3 Track4 Track5

n File

MP3/WMA/JPEG/WMV/AVI ﬁ les recorded on CD-R/-RW are

divided into large segments (folders) and small segments (ﬁ les).

Files are stored in folders, and folders can be placed for storage in

a hierarchy. This unit can recognize up to 8 hierarchies of folder.

  





File1 File2 File3

Folder3

1st level

2nd level

3rd level

 

File4 File5

 

File6 File7

Folder1 Folder2

CD-R/-RW

When writing MP3/WMA/JPEG/WMV/AVI ﬁ les on a CD-R/-RW disc,

set the writing software’s format to “ISO9660”. The ﬁ les may not play

properly if they are recorded in other formats. For details, refer to the

instructions of your writing software.

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁ cations Index

Getting

Started

ENGLISH

ENTER button ······························· (11, 38 – 40)

Used to conﬁ rm an item.

• TUNER mode ··············································· (22)

Used to register a broadcast station.

Q5 u/i buttons

• SETUP mode ··································· (11, 38, 40)

Used to select the item to be set.

• TUNER mode ··············································· (22)

Used when switching frequencies.

• DISC, iPod/USB mode ························ (28 – 31)

Used to select the item.

GWith the door openH

Q7 Q8 W0 W1 W2Q9

Part names and functions

Q6 MODE button

• SETUP mode ··············································· (39)

Calls up the SETUP menu when pressed

continuously.

• TUNER mode ··············································· (22)

Used to select reception band.

Q7 Headphones jack ········································ (13)

Q8 AUX1 input jack ·········································· (26)

Q9 iPod/USB1 port ··········································(25)

W0 SOURCE DIRECT button ···························· (13)

W1 STEREO button ··········································· (21)

W2 SURROUND button ···································· (21)

q Tone indicators

DBB: Lights when the dynamic bass boost

function is set to “ON”.

TONE: Lights when the tone (bass/treble) is

being adjusted.

w Surround mode indicators ························(21)

e Information display

Various information is displayed here.

r Play mode indicators

Lights when the random playback mode or

repeat playback mode is used.

t Remote control signal reception indicator

y Timer operation indicator ·························· (39)

Display

ew r

Q0 o i u y

u Tuner reception mode indicators ·············(22)

These light according to the reception conditions

when the input source is set to “TUNER”.

TUNED: Lights when the broadcast is properly

tuned in.

RDS: This light when receiving RDS broadcasts.

AUTO: Lights when “FM AUTO” is selected.

ST: In the FM mode, this light when receiving

analog stereo broadcasts.

MONO: Lights when “FM MONO” is selected,

or when an analog monaural broadcast is

received.

i Decoder indicators

These light when the respective decoders are

operating.

o Playback mode indicators

1 : During playback

3 : During pause

Q0 USB/DISC indicators

Lights when a disc or USB memory device is

installed.

Page is loading ...

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁcations Index

Getting

Started

ENGLISH

n Inserting the batteries

q Remove the rear lid in the

direction of the arrow and

remove it.

w Load the two batteries

properly as indicated by

the marks in the battery

compartment.

R03/AAA

e Put the rear cover back on.

NOTE

• Replace the batteries with new ones if the set does not operate

even when the “remote control” is operated close to the unit.

• The supplied batteries are only for verifying operation.

• Be sure to insert the batteries in the proper direction, following the

q and w marks in the battery compartment.

• To prevent damage or leakage of battery ﬂuid:

• Do not use a new battery with an old one.

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in

a ﬁre.

• Do not keep the battery in a place exposed to direct sunlight or in

places with extremely high temperatures, such as near a heater.

• If the battery ﬂuid leaks, carefully wipe the ﬂuid off the inside of the

battery compartment and insert new batteries.

• Remove the batteries from the “remote control” if it will not be used

for a long time.

• Used batteries should be disposed of in accordance with the local

regulations regarding battery disposal.

Part names and functions

n Operating range of the remote control unit

Operate the remote control unit while pointing it at the remote

sensor.

30°

Approx. 7 m

NOTE

The set may function improperly or the “remote control” may not

operate if the remote control sensor is exposed in direct sunlight or

strong artiﬁcial light such as a ﬂuorescent or infrared light.

W6 Fast-reverse-skip/Fast-forward buttons

(6/7) ···················································· (19)

TUNING buttons (+/–) ································ (22)

W7 Play button (1) ························· (18, 19, 28, 29)

W8 Pause button (3) ········································(18)

W9 RETURN button ···························· (34 – 37, 39)

E0 ENTER button ····································· (34 – 37)

E1 POP UP MENU button ·······························(16)

E2 SURROUND button ···································· (21)

E3 Master volume control buttons

(VOLUME df) ············································· (13)

E4 MUTE button ·············································· (13)

E5 Input source select buttons (INPUT) ········ (12)

E6 ANGLE button ············································(20)

E7 SUBTITLE button ········································ (21)

E8 DBB/TONE button ······································ (13)

E9 Picture in picture button (PIP) ··················· (17)

R0 SLEEP button ·············································· (39)

R1 Dimmer button (DIMM.) ···························· (13)

ENGLISH

This section explains how to connect speakers, TV, set-top box, antennas and power cord.

For other connections, see the sections below.

n Connecting an iPod or USB memory device to the iPod/USB1 port (vpage25)

n Connecting a USB memory device to the USB2 port (vpage26)

n Connecting a portable audio player (vpage26)

n Connecting to the network (vpage27)

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the user guide of the other components.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power supply cords together with connection cables.

Doing so can result in humming or noise.

Basic connections

Connecting speakers

Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being

connected to the unit, and be sure to connect the channels and polarities correctly.

Cables used for connections

Audio cable (sold separately)

Pin-plug cable

Speaker cable

Connecting the speaker cables

Protection circuit

The protection circuit is be activated in the

following situations:

• If the speaker cable wire touches the rear panel

or screws or if the speaker cable wire touches

the speaker cable’s + and – sides are touching

• If the surrounding temperature is extremely

high

• If the inside of the ampliﬁer gets hot to

extended use at a high output

If this happens, unplug the power cord, then check

the connections of the speaker cables and input

cables. If the unit becomes very hot, wait for it to

cool off and improve the ventilation around it. After

doing this, plug the power cord back in.

If the protection circuit is activated even though

there are no problems with the ventilation around

the unit or in connections, the unit may be

damaged. Turn off the power and then contact a

Marantz service center.

Peel off about 10 mm of sheathing from the tip

of the speaker cable, then either twist the core

wire tightly or terminate it.

NOTE

• Use speakers with an impedance of 6 to 8 Ω. The

protection circuit may be activated if speakers

with an impedance other than speciﬁed are used.

• Connect the speaker cables so they do not stick

out of the speaker terminals. The protection circuit

may be activated if the wires touch the rear panel

or if the + and – sides touch each other (vpage43

“Protection circuit”).

• Never touch the speaker terminals while the

power supply is connected. Doing so could result

in electric shock.

w q w q

(R) (L)

Subwoofer

with built-in

ampliﬁer

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁcations Index

Basic

Connections

ENGLISH

Connecting a TV

Select the connector to use and connect the device.

Cables used for connections

Audio and video cable (sold separately)

zThis interface allows transfer of

digital video signals and digital

audio signals over a single HDMI

cable.

HDMI cable z

Video cable (sold separately)

Video cable

VIDEO

HDMI

AUDIO

OUT

TV TV

HDMI function

• Deep Color (vpage36 “Color Depth”)

In order to play back digital video and audio such as BD-Video or DVD-Video via HDMI connection, both

this unit and TV need to support the copyright protection system known as HDCP (High-bandwidth

Digital Content Protection System). HDCP is copyright protection technology comprised of data

encryption and authentication of the connected AV device. This unit supports HDCP.

• If a device that does not support HDCP is connected, video and audio are not output correctly. Read

the user guide of your television for more information.

About HDMI cables

• Use a cable on which the HDMI logo is indicated (a certiﬁed HDMI product) for connection to the HDMI

connector. Normal playback may not be possible when using a cable other than one on which the HDMI

logo is indicated (a non-HDMI-certiﬁed product).

• When a device supporting Deep Color signal transfer is connected, use a cable compatible with HDMI

version 1.3a.

NOTE

• Do not connect the this unit’s video output via a VCR (Video Cassette Recorder). Some media contain

copy prohibit signals, which will disturb the screen image.

• When the HDMI video resolution is set to “HDMI Auto” as described in “Resolution” (vpage36), the

outputs the highest resolution video signal that is supported by the connected equipment.

• If the HDMI resolution is not set to “HDMI Auto”, set it to correspond with the resolution of your

television. Images will not be displayed normally if the television resolution and this unit’s output

resolution do not match.

• Audio and video will be temporarily interrupted if the power of the connected device currently playing

back is turned off, or input is switched.

• When you change the HDMI video resolution of this unit, it takes from a few seconds up to about 10

seconds for validation between this unit and the connected device. Audio/video is not output during this

period.

• If the resolution of video signal to be output from HDMI OUT does not match that of your TV, the picture

is not clear, natural or displayed.

Should this happen, ﬁrst make (composite) video connection between this unit and TV, and select the

(composite) VIDEO as an input source on the TV to display the setting menu, then set the Resolution

correctly. (For details on the resolution acceptable for your TV, refer to its operating instructions.)

• Among the components that support HDMI, some components can control other components via the

HDMI connector. However, this unit cannot be controlled by another component via the HDMI connector.

Connecting to a device equipped with a DVI-D connector

When an HDMI/DVI conversion cable (sold separately) is used, the HDMI video signals are converted to

DVI signals, allowing connection to a device equipped with a DVI-D connector.

NOTE

• No sound is output when connected to a device equipped with a DVI-D connector. Set “HDMI Output”

(vpage36) in the menu to “Off Speaker”, and output audio from the speakers.

• Signals cannot be output to DVI-D devices that do not support HDCP.

• Depending on the combination of devices, the video signals may not be output.

• The video signal will be in RGB format.

n Settings related to HDMI connections

Set as necessary. For details, see the respective reference pages.

Audio (vpage36)

Make settings for HDMI video/audio output.

• HDMI Output

ENGLISH

Connecting an antenna

• Connect the FM antenna or AM loop antenna supplied with the unit

to enjoy listening to radio broadcasts.

• After connecting the antenna and receiving a broadcast signal

(vpage22 “Listening to FM/AM broadcasts”), ﬁx the antenna with

tape in a position where the noise level becomes minimal.

w e

AM loop antenna

(Supplied)

FM indoor antenna

(Supplied)

White Black

NOTE

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the AM

loop antenna.

• Make sure the AM loop antenna lead terminals do not touch metal

parts of the panel.

• If the signal has noise interference, connect the ground terminal

(GND) to reduce noise.

• If you are unable to receive a good broadcast signal, we recommend

installing an outdoor antenna. For details, inquire at the retail store

where you purchased the unit.

n AM loop antenna assembly

Put the stand section

through the bottom of the

loop antenna from the

rear and bend it forward.

Loop

antenna

Stand

Square

hole

Projecting

part

Insert the projecting part

into the square hole in the

stand.

n Using the AM loop antenna

Suspending on a wall

Suspend directly on a wall without assembling.

Nail, tack, etc.

Standing alone

Use the procedure shown upper to assemble.

Connecting a set-top box (Satellite

tuner/Cable TV)

You can watch satellite or cable TV.

Cables used for connections

Audio cable (sold separately)

Audio cable

(White)

(Red)

OUT

AUDIO

Satellite Tuner/

Cable TV

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁ cations Index

Basic

Connections

ENGLISH

Connecting a wireless receiver (RX101)

By connecting a wireless receiver RX101 (sold separately) to this unit,

you can receive and playback audio signals from other devices using

the Bluetooth Communication Function.

• Use a Bluetooth device that is A2DP compatible (vpage 42

“A2DP”).

• You can also use wireless receiver RX101 as an external IR receiver.

• For instructions on the wireless receiver settings, refer to the

RX101’s operating instructions.

Wireless receiver RX101

Bluetooth device

( A2DP Compatibility)

Remote control unit

Remote control connection

The unit can be controlled using the remote sensor of RX101

connected to the unit. Be sure to set “IR=DISABLE” when controlling

in this way.

NOTE

When making this remote control connection, be sure to set the IR

switch of RX101 that is connected to the unit, to ON.

n Setting the remote control

Press ON/STANDBY to

set the unit to standby

mode.

Press and hold down

2 and then press ON/

STANDBY

“IR=ENABLE” or

“IR=DISABLE” on the

display.

Press ui to select “IR=DISABLE” or

“IR=ENABLE” and then press ENTER.

NOTE

The unit cannot be controlled using the remote controller while

“IR=DISABLE” is set.

Connecting the power cord

Power cord

(Supplied)

To household power outlet

(AC 230 V, 50 Hz)

NOTE

• Do not plug in the power cord until all connections have been

completed.

• Only use the supplied power cord.

• Be sure the power cord is unplugged from the power outlet before

connecting or disconnecting it to the AC IN.

ENGLISH

n Completely turning off the power

Unplug the power cord from the wall outlet.

• Note that the time setting is cleared when the power cord is

unplugged from the outlet.

• The settings made for the various functions may be cleared if the

power cord is left unplugged from a power outlet for an extended

period of time.

Selecting the input source

Press the input source select button

(AUX

, M-XP, DISC, iPod/USB1,

TUNER) to be played back.

The desired input source can be selected

directly.

z Each time AUX is pressed, the input source is changed as shown

below.

AUX2AUX1

AUX3

n Using the button on the main unit

Press INPUT.

• Each time INPUT is pressed, the input

source is changed as shown below.

TUNER iPod/USB1DISC/USB2

AUX3

M-XPort

AUX2 AUX1

z “M-XPort” is displayed when a RX101 wireless receiver is

connected to “M-XPort”.

Basic operations

n Playable media (vpage14)

n About playback information (vpage15)

n Playing Blu-ray Disc, DVD-Video and CD

(vpage16)

Advanced operations (vpage28)

Playback (Basic) (vpage18)

n Turning the power on (vpage12)

n Turning the power off (vpage12)

n Selecting the input source (vpage12)

n Adjusting the master volume (vpage13)

n Turning off the sound temporarily (vpage13)

n Switching the display’s brightness (vpage13)

n Adjusting the tone (vpage13)

n Listening with headphones (vpage13)

n Source direct mode (vpage13)

n Setting the current time (24-Hour Display)

(vpage14)

Important information

Before starting playback, make the connections between the different

components and the settings on the receiver.

NOTE

Also refer to the operating instructions of the connected components

when playing them.

Preparations

Turning the power on

Press POWER.

The power turns on.

You can also switch the power on by pressing

ON/STANDBY on the main unit.

Press again to set the power to standby.

NOTE

• Power continues to be supplied to some of the circuitry even when

the power is in the standby mode. When leaving home for long

periods of time, either press ON/STANDBY or POWER to turn off

the power, or unplug the power cord from the power outlet.

• Be sure to stop playback before turning the power off.

Turning the power off

Press POWER.

The power turns off.

NOTE

• Be sure to stop playback before turning the power off.

• Make sure that the disc tray is completely shut before turning off

the power.

• Do not push the disc tray by hand when the power is turned off.

Doing so could damage the set.

Getting

Started

Basic

Connections

Advanced

Connections

Basic

Operations

Advanced

Operations

Other

setting

Settings

Other

information

Explanation

terms

Troubleshooting Speciﬁ cations Index

Basic

Operations

ENGLISH

Operations possible during playback

Adjusting the master volume

Use VOLUME df to adjust the

volume.

The volume level is displayed.

GAdjustable rangeH

VOLUME 00 – 59, VOLUME MAX

• The variable range differs according to the

input signal.

You can also operate via the main unit. In this

case, perform the following operations.

Press VOLUME df to adjust the volume.

Turning off the sound temporarily

Press MUTE.

“MUTE ON” is displayed.

To cancel, press MUTE again. Muting can also be canceled by adjusting

the master volume.

Switching the display’s brightness

Press DIMM..

100 % 70 %

40 %Off

• The display’s brightness switches each

time the button is pressed.

Adjusting the tone

Use DBB/TONE to select the tone

parameter to be adjusted.

DBB BASS

TREBLE

Adjust the volume with 8

9 or o p.

• To make other tone adjustments at this

time, press DBB/TONE.

• If no operation is performed for 5 seconds,

the adjustment is retained and the normal

display reappears.

DBB

Emphasize the bass sound. (Dynamic Bass Boost)

GSelectable modesH

–

OFF

BASS

Adjusts the bass sound.

GVariable rangeH

–10dB

–

+10dB

TREBLE

Adjusts the treble sound.

GVariable rangeH

–10dB

–

+10dB

Settings made upon purchase:

• DBB .......................................OFF

• BASS ..................................... 0dB

• TREBLE ................................. 0dB

DBB and BASS can be set simultaneously. If the settings were

performed at the same time, the BASS variable range may differ

depending on the volume level.

Listening with headphones

Plug the headphones (sold separately) into the .

• The sound from the speakers is automatically cut off.

NOTE

To prevent hearing loss, do not raise the volume level excessively

when using headphones.

Source direct mode

As the audio signal does not pass through the tone control circuit (DBB/

BASS/TREBLE) in source direct mode, the playback reproduction is

closer to the original sound.

Press S.DIRECT.

• If SOURCE DIRECT on the main unit is pressed, the same function

as with the remote control unit can be obtained.

ENGLISH

Playable media

Discs

Playable discs

Playable

formats/

modes

Playable region

codes

Marantz M-ER803 Owner's manual

Brand: Marantz

Model: M-ER803

Category: Blu-Ray players

Type: Owner's manual

Download PDF

report

Marantz M-ER803 Owner's manual

Marantz M-ER803 Owner's manual

Related papers

Other documents