FURNITURE JAKARTA LONG JOHN User manual

Brand
FURNITURE
Model
JAKARTA LONG JOHN
Type
User manual

This manual is also suitable for

Big Table Size: 120 x 39 x 42 cm (WDH)
Small Table Size: 54 x 39 x 36 cm (WDH)
Colour: Mango
Finish: Melamine Veneer
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
Thank you for purchasing the Jakarta Long John Nest.
Please read the instructions carefully to ensure safe operation of this product.
Page 1 of 7
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and fittings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking.
Tools Required
Number of people
x1
0.5 Hour
Set Up
PO No : 6131
Version 1 - 010120
Page 2 of 7
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
CARE INFORMATION
•Never use scourers, abrasives or chemical cleaners.
•To clean, wipe with a damp sponge and warm soapy water.
•Do not use solvent based cleaners or detergents as they can bleach or damage the product.
WARNINGS
•Each table is designed to hold 10Kg in total. Do not exceed this weight.
•We recommend that this unit is assembled in the room intended for use.
•When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
•Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent them from getting scratched.
•Check the pack and make sure you have all the parts listed.
•Ensure that this product is fully assembled as illustrated before use.
•Check all screws or bolts are tightened and inspect regularly.
•Tools not included unless specified in the parts list.
•This product should only be used on a firm and level floor.
•Please do not drag across the floor or carpet as legs may be damaged - lift into place.
•Make sure the legs remain in contact with the floor when being used.
•Keep small parts out of reach of children.
•DO NOT
•DO NOT
•DO NOT
•DO NOT
•DO NOT
•DO NOT
use tables for 12 Hours to allow dowel glue to dry - see Steps 2 & 3.
use power tools to construct this product.
tighten screws until parts are assembled or as advised in this guide.
over tighten screws or bolts.
use this product if parts are missing, damaged or worn.
sit or stand on the Tables.
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
Version 1 - 010120
Page 3 of 7
Parts and Fittings Checklist
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer.
The fittings pack contains small items that should be kept away from children.
1
2
2
3
3
4444
All parts are packed in one carton
Description: Short Side Panels
Qty: 4
Size: 310 x 388 x 50 mm
Carton No: 1/1
4
1
2
3
Description: Long Table Top
Qty: 1
Size: 1200 x 390 x 50 mm
Carton No: 1/1
Description: Tall Side Panels
Qty: 2
Size: 370 x 388 x 50 mm
Carton No: 1/1
Description: Short Table Tops
Qty: 2
Size: 540 x 390 x 50 mm
Carton No: 1/1
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
Version 1 - 010120
Page 4 of 7
6A
6B
6C
Item QuantityCode
Fittings (to scale)
Flat Washer
(for M8 Nuts)
Nuts (for M8 bolts)
12D Dowels (8x60mm)
6H Plastic Cover (38mm)
Bolt (M8x80mm)
10 20 30 40 50 60 70 80
General Hints & Tips
Fittings (not to scale)
QuantityCode Item
6E Bracket
1
1
FWood Glue for Dowels
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
GSpanner (for M8 nuts)
A
A
E
B
C
GH
Version 1 - 010120
Page 5 of 7
STEP 1
STEP 2
For this step:
Tools required
For this step:
Tools required
Fittings required
B x2
C x2
D x4
E x2
F x1
G
D
1
1
2
2
3
x2
A
Fittings required
A x6
D
D
D
D
Put glue in all x8 dowel
holes & allow to dry -
please do not use or move
table for at least 12 Hrs.
F
F
F
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
A
A
A
A
E
B
C
G
H x2
H
Version 1 - 010120
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
x2
Page 6 of 7
Warning:
STEP 3
STEP 4
For this step:
Tools required
For this step:
Tools required
Fittings required
After assembling, please do not use or
move product for at least 12 hours to
make certain glue has time to dry.
D
3
Put glue in all x8 dowel
holes & allow to dry -
please do not use or move
table for at least 12 Hrs.
F
A
E
B
C
G
4
4
D
DD
D
F
F
Fittings required
B x4
C x4
D x8
E x4
F x1
G
H x4
H
Version 1 - 010120
Page 7 of 7
Assembly Completed
Your Jakarta Long John Nest is now completely assembled.
Periodically check to ensure that the components are in their proper position, free from damage.
Also, make sure the connectors are tight and secure.
Keep instructions for future reference
JAKARTA LONG JOHN NEST OF TABLES - ASSEMBLY INSTRUCTIONS
Version 1 - 010120
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

FURNITURE JAKARTA LONG JOHN User manual

Brand
FURNITURE
Model
JAKARTA LONG JOHN
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents