2. Edelbrock
  3. 1932

Edelbrock 1932, 19321932, QuadraJet Hot Air To Electric Choke Conversion Kit #1932 User manual

  • Hello, I'm your chat assistant. I've reviewed the Edelbrock 1932 Electric Choke Conversion Kit installation instructions. This document details how to convert your hot-air choke system to an electric one. It includes instructions on drilling out rivets, connecting the wire to a 12 volt source, and installing a vacuum cap. Feel free to ask me any questions.
  • What size drill bit is needed to remove the choke thermostat?
    What should be done with the open vacuum tube on the carburetor's choke housing?
    Where should the choke wire be connected?
Q-JET ELECTRIC CHOKE CONVERSION KIT
For Converting Hot-Air Choke to Electric Choke
Catalog #1932
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. If you have any questions, please call our Technical Hotline at:1-800-416-8628, 7:00 am - 5:00 pm,
Pacific Standard Time, Monday through Friday or e-mail us at [email protected].
•DESCRIPTION: Kit converts Q-Jet hot-air choke to electric choke. Use in applications where an intake manifold that does not accept hot-air choke is being used with the original
hot-air choke Q-Jet carburetor, to repair a damaged hot-air choke, or when aftermarket cylinder heads (such as Edelbrock Performer) that do not have a large enough exhaust
crossover passage to accept the hot-air choke tube are used.
NOTE: In applications where an intake manifold that accepts hot-air choke will be retained, a
block-off plate will be required. Edelbrock Intake manifolds include a block off plate. On stock
manifolds, a plate will need to be fabricated, or the choke tubes may be cut close to the intake
manifold and remain installed to prevent exhaust leaks.
•INSTALLATION:
1. In order to properly remove the choke thermostat from the choke housing, an 11/64” drill
bit must be used to drill out the rivets attaching the choke cover to the choke housing
(See Figure 1)
. Drill through choke housing to provide clearance for self-tapping screws
provided.
2. Attach the electric choke thermostat to the housing using the supplied self-tapping
screws and retaining clips.
3. Connect the supplied choke wire to a 12 volt key-on switched source (Power is on ONLY
when ignition key is in the “ON” position), and attach the connector end of the wire to the
choke thermostat.
NOTE: Always disconnect the battery before making any electrical
connections.
4. Using the supplied 1/4” vacuum cap, block off the open vacuum tube on the carburetors choke housing
(See Figure 1)
.
Trim Choke Tubes
Here, or Install
Block-Off Plate
After Disconnecting
Choke Tubes, Install
Vacuum Cap Here
FIGURE 1
Drill Out Rivets Using
11/64” Drill Bit
©2007 Edelbrock Corporation
Brochure #63-0422
Catalog #1932
Rev. 10/07 - AJ/mc
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503 • Tech-Line: 800-416-8628 • E-Mail: [email protected]
Q-JET ELECTRIC CHOKE CONVERSION KIT
For Converting Hot-Air Choke to Electric Choke
Catalog #1932
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. If you have any questions, please call our Technical Hotline at:1-800-416-8628, 7:00 am - 5:00 pm,
Pacific Standard Time, Monday through Friday or e-mail us at [email protected].
•DESCRIPTION: Kit converts Q-Jet hot-air choke to electric choke. Use in applications where an intake manifold that does not accept hot-air choke is being used with the original
hot-air choke Q-Jet carburetor, to repair a damaged hot-air choke, or when aftermarket cylinder heads (such as Edelbrock Performer) that do not have a large enough exhaust
crossover passage to accept the hot-air choke tube are used.
NOTE: In applications where an intake manifold that accepts hot-air choke will be retained, a
block-off plate will be required. Edelbrock Intake manifolds include a block off plate. On stock
manifolds, a plate will need to be fabricated, or the choke tubes may be cut close to the intake
manifold and remain installed to prevent exhaust leaks.
•INSTALLATION:
1. In order to properly remove the choke thermostat from the choke housing, an 11/64” drill
bit must be used to drill out the rivets attaching the choke cover to the choke housing
(See Figure 1)
. Drill through choke housing to provide clearance for self-tapping screws
provided.
2. Attach the electric choke thermostat to the housing using the supplied self-tapping
screws and retaining clips.
3. Connect the supplied choke wire to a 12 volt key-on switched source (Power is on ONLY
when ignition key is in the “ON” position), and attach the connector end of the wire to the
choke thermostat.
NOTE: Always disconnect the battery before making any electrical
connections.
4. Using the supplied 1/4” vacuum cap, block off the open vacuum tube on the carburetors choke housing
(See Figure 1)
.
Trim Choke Tubes
Here, or Install
Block-Off Plate
After Disconnecting
Choke Tubes, Install
Vacuum Cap Here
FIGURE 1
Drill Out Rivets Using
11/64” Drill Bit
©2007 Edelbrock Corporation
Brochure #63-0422
Catalog #1932
Rev. 10/07 - AJ/mc
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503 • Tech-Line: 800-416-8628 • E-Mail: [email protected]
/