SKYTRONIC 351.148 IP Camera User manual

MJPEG SERIES OUTDOOR

WiFi outdoor IP Camera

BEFORE YOU BEGIN

Please unpack the box carefully and identify that all the parts are present.

The Camera is suitable for indoor or outdoor use.

Check the voltage of the power supply. Make sure you use the recommended power

input (12V DC, 1.0A). Use of incorrect voltage is not covered by the warranty.

Do not attempt to open the casing to access the Camera. Damage caused to the

product by tampering with the casing is not covered by the warranty.

Do not aim the camera at the sun or similar intense light.

The interval time of powering the camera on and off must be more than 10 seconds

otherwise it will cause serious damage to the CPU.

When you update the cameras, please ensure you:

- connect the camera directly to a computer using a network cable

- close other programs and windows on the computer

- keep the power connected when updating the firmware

PRODUCT DESCRIPTION

Camera combines a high quality digital

charge-coupled device (COMS) with a

powerful wireless web server for clear

images from anywhere on your local

network or over the internet.

Can be used on WiFi or Wired Networks.

Dual resolution, 640x480 or 320x240

pixel resolution.

Expand the system at any time by adding

up to 35 additional cameras.

View cameras in Split Screen view or

watch the camera detecting movement

full screen.

Cameras can be viewed via standard

PC or Mac browsers including Internet

Explorer, Safari, Chrome and Firefox.

IR LEDs for up to 20m Night Vision.

Cameras can be mounted indoors or

outdoors.

Includes Multi-level user management

which can be configured with secure

password access.

Easy to use web browser controls. Also

allows quick configuration changes via

the Settings menu.

View live images on your 3G Smartphone.

Supports image snapshots and image

sending via Email and FTP upload.

Supplied with free 36 Camera Windows

Recording and Viewing software.

FEATURES

NOTES ON WINDOWS AND MAC COMPATIBILITY:

- IP camera setup should be completed on a Windows PC only using Internet Explorer.

- Live viewing, taking snapshots, recording and camera configuration are fully supported on Windows

PCs.

Mac users are only able to:

- view live images via compatible web browsers including Safari, Firefox and Chrome but are

limited to viewing one camera at a time.

- take and save snapshot images via the web browser interface.

WiFi outdoor IP Camera can be set up in minutes for instant monitoring and live viewing on your

Mac or Windows computer and 3G Smartphone - all via your wireless network router or switch

For optional recording, simply install the Smart Witness recording software to you r Windows PC

and configure it to your particular requirements.

PACKAGE CONTENTS

Power Adaptor

Allen Key Screws and Wall Plugs

WiFi Camera with

Bracket & Antenna

Software

Installation CD

CAMERA INSTALLATION

1. Begin by screwing the antenna and bracket to the camera and power the camera using the power

supply provided.

2. Using a standard Ethernet network cable, connect the camera to your wireless network.

The camera can either be connected to a router/switch or directly to a PC with an Ethernet network

cable. We recommend you setup the camera initially on your network using a wired connection

before it is used wirelessly.

3. Continue with setup (read the next chapter) and once the camera has been successfully setup on

your network, it can be mounted on a wall using the wall plugs and screws provided. (Camera setup

is designed for Windows PCs only).

CAMERA SETUP continued

Please note that if you are using the camera on a wireless network you will need to

first configure the camera for wired use, before you programme your wireless settings

in to it.

1. Insert the Installation CD into your PC CD drive and the installation screen should appear

automatically. If it does not, click ‘Start > Run> Browse...’ to locate the CD on your computer .

2. Double click ‘IPCamSetup.exe’ and install the software as instructed.

3. Click Next, to complete the software installation.

The computer will restart upon completion of the installation and a new icon will appear on the

desktop automatically called ‘IP Camera Tool’.

4. Double click the icon to start the IP Camera Tool software. The software is designed to search the

Local Area Network (LAN) for any connected IP cameras or devices.

CAMERA SETUP continued

After searching, the software will give one of 3 results:

Connected IP cameras are located on the LAN - All the IP cameras will be listed and will be

displayed in the result field as shown below.

No IP Camera found within LAN - After about 1 minute search, the result field will show ‘Not

Found IP Server’ and the software application will shut down automatically.

The IP Cameras installed within LAN do not share the same subnet with the monitoring

PC. A prompt will be shown in result field ‘Subnet doesn’t match, double click to change!’ Double

click the mouse button and select ‘Network Configuration’ to set the IP address of the Camera to

the same subnet as LAN.

When you select an IP camera from the list and click the right mouse button, there are five options:

- Basic Properties

- Network Configuration

- Upgrade Firmware

- Refresh Camera List

- Flush Arp Buffer

Basic Properties

View device information such as Device ID, System Firmware Version, Web UI Version.

CAMERA SETUP continued

Network Configuration

Configure the Network parameters from this page.

• DHCP checkbox: If checked, the device will obtain an IP from the DHCP server (ensure the Router, with

which the device connects, has a DHCP function).

• IP address: Fill in the IP address assigned and make sure it is in the same subnet as the gateway (i.e. the

first three sections are the same).

• Mask: The default subnet mask of the equipment is: 255.255.255.0

• Gateway: Make sure it is in the same subnet with PC IP address. Default Gateway address is 192.168.0.1

• DNS: IP address of IPS network provider.

• Port: LAN port assigned for the equipment, usually 80.

• User & Password: (Default administrator User Name/Password = admin/No password).

If you enable using DHCP, the system will assign an IP address for your equipment only if your

gateway supports DHCP (which is the case with most gateways). NOTE: When the subnet doesn’t

match, double click to change it and set the camera’s IP address once again.

Upgrade Firmware

Enter the correct User Name and Password to upgrade the system Firmware and Web user interface.

Refresh Camera List

Refreshes the camera list manually.

CAMERA SETUP continued

Flush ARP Buffer

ARP stands for Address Resolution Protocol. It is used to associate a layer 3 (Network layer) address

(such as an IP address) with a layer 2 (Data Link layer) address (MAC address). When a wired

network and a wireless network of the camera both use the same fixed IP address, a problem may

occur where connections to web pages will time out and fail. Use the Flush ARP Buffer to clear the

ARP cache and fix the error.

5. Access the IP camera through the IP Camera Tool or IE directly. Either:

• Double click the IP address of the IP camera listed in the search result window. Internet Explorer will be

opened automatically and display the camera login page.

Access the camera via the Internet Explorer browser directly by typing in the camera’s IP address. In the window

that appears, click the ‘Sign in’ button as shown below:

6. The Camera Login page will pop up. Enter your account and password on the login page.

By default administrator’s username is: admin and no password. Click Sign in to enter the

monitoring page. You can enter the page as an Administrator, Operator or Visitor. Each type of user

will allow different levels of access on the web browser interface. Read below for more information

on the access rights and user interface.

Visitor: In this mode, you can only view.

Operator: You can control the image setting of IP Camera and set some parameters.

Administrator: You can setup the advanced configurations of the IP Camera.

7. If you are using a PC, follow the top link for IE Browsers. This will activate ActiveX which allows

access to additional functions of the user interface.

If you are a Mac user, you can view the camera via the second link, Server Push Mode. This web

browser mode features limited functionality but allows Live View and Image Snapshots.

CAMERA SETUP continued

Main User Interface (as seen in Internet Explorer)

Device Status

Indicates the number of cameras connected on the network.

For Viewer

Allows you to view Full Screen or in Split Screen. Select the icons according to the view preferred.

For example: Select for Full Screen, for Quad view or for Multi Split Screen.

Add timestamp on record

When checked, a timestamp will be added in the bottom right corner of recorded videos.

OSD (On Screen Display) for Multi-Device Settings

Display the date and time on the video. You can disable the OSD function.

Audio buffer

Set the audio buffer time in sconds.

Audio switch

Click to enable the audio stream for the camera. The icon will change to . Click this to stop

the audio.

Record

Click icon to go into Record mode. Click to stop. (Audio recording is active if audio is on).

CAMERA SETUP continued

Snapshot: Click the icon to take a snapshot image.

Note:

Recorded video file names will be saved in the format: CameraName_ Current time.

For example: IPCAM_20081211134442. This recording is from the camera called IPCAM and the

recording ‘end’ time was 13:44:42 on December 11, 2008.

For operator

When you login as an Operator or Administrator, you can enter the ‘For Operator’ page.

Mirror

Click the icons to see the horizontal or vertical mirror image.

Resolution

Select either VGA (640x480) or QVGA (320x240).

Work mode

Select either 50Hz, 60Hz or Outdoor.

Brightness and Contrast parameters

Click the + or - icons to adjust the brightness and contrast of the camera image.

Default All

Click to return the settings to the factory defaults.

For Administrator

When you login as an Administrator, the ‘For Administrator’ functions are enabled.

Device Info - You can find information about the camera such as the Device ID, Firmware Version

and Embeded Web UI Version.

Alias Settings - You can change the name of the IP camera.

Data & Time Settings - Set the time and date.

CAMERA SETUP continued

User Settings - You can configure up to 8 user names and passwords and the level of users as

Administrator, Operator or Visitor.

Administrators can:

Set Record Path - Click ‘Browse’ to choose the recording path of where video files will be saved.

Set Alarm Record Path - Click ‘Browse’ to choose the alarm recording path.

Note:

1. The default path for saving files is C:\Documents and Settings\All Users\Documents.

2. In Windows Vista, there are two points you need to notice:

• Vista’s Security level is higher than Windows XP/2000. For the ‘Set Record Path’ function, you will need to

add the add the Device IP address to IE’s ‘Trusted sites’ first. To do this go to: Tools > Internet Properties >

Security >Trusted sites > Sites > Add. In Vista, there is a prompt to add Trusted sites when the Set Record/

Alarm Record path is clicked.

• You cannot set the Windows System Root Directory as you will do for the Record/Alarm Record Path. This

prompt only pops-up in Vista.

UPnP Settings - Access this page to make sure the UPnP Status is working.

Upgrade Device Firmware - Upgrade the camera’s Firmware and device embeded web UI software on

this page.

Restore Factory Settings - Restore factory settings of the device.

Reboot Device - Reboot the device.

CAMERA SETUP continued

Multi-Device Settings

In the Multi Device Settings page, you can see all devices searched in the LAN.

The ‘1st Device’ is the default IP camera. You can add more cameras to the list in the network for

monitoring. The web browser software supports up to 9 IP cameras simultaneously.

To add cameras to the LAN

Click ‘The 2nd Device’ and double click the IP camera from the ‘Device List in LAN’. The Alias Host and

HTTP Port will fill in automatically. Enter the correct User Name and Password then click ‘Add’. Add more

cameras in the same way.

To add cameras to the Internet

Firstly, make sure the camera added can be accessed on the Internet with the IP address or DDNS domain. (as:

http://202.96.133.134: 9008 or http://ipcamera.dyndns.org:9008).

Enter the Host in the format: 202.96.133.134 port:9008 or Host: ipcamera.dyndns.org port:9008. Enter the

correct User Name and Password then click ‘Add’. Add more cameras in the same way.

Basic Network Settings

If the router that the IP camera connects to has a DHCP function, you can choose ‘Obain IP from

DHCP Server” and fill in the network parameters manually.

HTTP Port - In most cases, you can leave this value as 80, however, if your Internet Service Provider blocks this

port, you may have to switch to another port number such as 8005.

CAMERA SETUP continued

Wireless LAN Settings

Enter the wireless settings page of the Wireless Router to find out the SSID, Channel, Encryption and

Authentication details. This product supports WEP and WAP security encryption.

ADSL Settings

When connected to the Internet through ADSL, you can enter the ADSL username and password

obtained from your ISP.

DDNS Service Settings

The system supports protocols from some DDNS providers such as dyndns.org. Enter the following

information once the DDNS information has been setup.

User and Password: The User Name and Password used when applying for the domain name.

DDNS Host: The domain name.

DDNS or Proxy Server: If you access the DDNS host through a proxy, you should input the Proxy IP.

DDNS or Proxy Port: The Proxy Port.

CAMERA SETUP continued

Mail Service Settings

Configure the Email addresses that will receive and send mails after an alarm is raised.

Sender - This device uses the sender mailbox to send mails.

Receiver - To receive the mail from the Sender.You can set up to 4 receiver mailbox.

SMTP Server - The SMTP server for the sender mailbox.

Need Authentication - Check the box if the email needs authentication then input the SMTP User Name &

Password.

Mail test: Set the Mail parameters then click ‘Submit’ first before sending a test email.

There are 8 possible Mail Test errors:

1. Cannot connect to the server.

2. Network Error. Please try later.

3. Server Error.

4. Incorrect username or password.

5. The Sender is denied by the server - The server needs to authenticate the user, check settings and try again.

6. The Receiver is denied by the server - Could be caused by the anti-spam privacy settings of the server.

7. The message is denied by the server - Could be caused by the anti-spam privacy settings of the server.

8. The server does not support the authentication mode used by the device.

CAMERA SETUP continued

Report Internet IP by Mail - Check the box so when the IP camera is powered on or the Internet IP address

changes, an email will be sent. (For example: IPCAM ‘s url is http://119.123.207.96:9002). Make sure the port

is mapped to the router correctly by UPnP or Virtual Map function.

FTP Service Settings

Note: When Alarm Service Settings > Upload Image on Alarm is checked, the FTP Service takes effect.

FTP Server - The FTP server address.

FTP port - The port usually is 21.

FTP Mode - Supports standard (POST) mode and passive (PASV) mode.

Upload Image Now - Check the box to upload the image. When checked, you can input the upload interval

time in seconds.

FTP Test - Set the FTP parameters and then click ‘Submit’ before testing the FTP settings. If successful, it will

display the prompt. There are 8 possible FTP test errors:

1. Cannot connect to the server - Please check FTP Server settings.

2. Network Error. Please try later.

3. Server Error.

4. Incorrect username or password - Check the username and password.

5. Cannot access the folder - Ensure the folder exists and your account is authorized.

6. Error in PASV mode - Ensure the server supports PASV mode.

7. Error in PORT mode - PASV mode should be selected if the device is behind a NAT.

8. Cannot upload file - Ensure your account is authorized.

CAMERA SETUP continued

Alarm Service Settings (Motion Detection)

Enter the Alarm Service Settings page to configure the Motion Detection function. When you enable

motion detection, the camera can be triggered to send email alerts and upload images. In the

camera monitoring page, the green icons will turn to red and you will hear an alert sound if motion

is detected.

Motion Detection Sensitivity - You can choose a level from 1 to 10. The most sensitive is 10.

Input Pins - The input pins can be used for a 1-way external sensor input. For example, you can connect a

Passive Infrared Sensor (PIR) to it for motion detection. When an external sensor is triggered, the IP camera

can be programmed to send an email with an image snapshot or control the internal relay output. If you link a

external alarm with Pin3 and Pin4, and enable alarm input, the external alarm will be enabled.

Send Mail on Alarm- Sends picture & mail information to the set Email address after the alarm is triggered.

Upload Image on Alarm - Enable this function to upload an image after the alarm is triggered.

REC on schedule and save to PC - Enable this function for automatic recording to start on schedule for

several seconds and save to the PC if there is an alarm triggered.

ACCESSING THE WIFI CAMERA

Using the WiFi Function

To use the wireless functions of the IP Camera a wireless router is required. Follow the instructions

below to get started after the camera has been mounted properly.

1. Use the Network cable to connect IP Camera to the LAN.

2. Enter IP Camera Tool to search for the IP camera.

3. When IP address of the camera is listed in the Result Field of the IP Camera Tool, it means the

basic configuration is completed.

4. Set the security settings in Internet Explorer on the PC when you view it for the first time.

5. Login to the web browser of the IP camera.

6. Now you can use the IP Camera as a Visitor, Operator or Administration in the LAN.

7. Enter the wireless router setup page and enter the SSID, Channel, Security Way (NONE,

WEP), Authentication Type and Encryption. NOTE: The product supports WEP and WAP

security encryption.

8. Click Submit to reboot the device.

9. Wait at least 30 seconds then unplug the ethernet cable and the power supply. Then power on the camera

ensuring only the power supply is connected. After 30 seconds, if the LED blinks, it indicates the IP camera is

working in WiFi mode.

Connect to the Internet through ADSL directly

1. Use the Network cable to connect IP Camera to PC.

2. Enter IP Camera Tool to search for the IP camera.

3. Login to the IP camera web browser page as an Administrator.

4. Enter the ADSL Settings page to input ADSL User Name and password.

5. Enter DDNS Settings Page and enable the DDNS service and click ‘Submit’ to reboot the camera.

6. Connect IP Camera to the ADSL directly, you can access the Camera from Internet by the domain

name.

NOTE: Choose the option ‘Report ADSL IP by Mail’, for the ADSL IP address to be sent via Email.

ACCESSING THE WIFI CAMERA continued

Connect to the Internet using a router to access the Internet

Follow the steps to use a router to access the Internet by shared ADSL. If a router is set for dial-up

Internet access, setting an ADSL dial-up account and password on the IP Camera is not required.

1. Use the Network cable to connect IP Camera to the LAN.

2. Enter IP Camera Tool to search for the IP camera.

3. Login to the IP camera web browser page as an Administrator.

4. Enter DDNS Settings Page and enable the DDNS service and click ‘Submit’ to reboot the camera.

5. Access the Camera directly from the Internet by using the domain name.

Static IP address users

Static IP address users do not need to use DDNS for remote access. When the settings of the IP

camera in LAN mode complete, you can access the Camera directly from the Internet by the WAN IP.

You can obtain the WAN IP address in two ways.

1: Obtain the WAN IP from a Website

You can discover this easily by opening on a computer using the same connection as the IP camera

and entering this address: http://www.whatismyip.com. The page at this address will show you the

current WAN IP.

2: Obtain the WAN IP address from the router

1. Obtain the IP address of the router (LAN Gateway address), User Name and Password for logging

into the router.

2. Enter the LAN IP address of the router (ie:192.168.1.1) in the address bar of your PC browser to

log on to the router.

3. Open the Status page to find out the WAN address of the router (ie: 116.25.51.115).

ACCESSING THE WIFI CAMERA continued

Access the IP Camera from the Internet

User can access the IP Camera from the Internet by entering the WAN IP address + port number into

the browse. For example, http://116.25.51.115:85.

Note: Make sure the Port mapping is successful. You can configure port mapping by two ways:

•EntertheSettingspageoftherouter,withwhichtheIPcameraconnects,toenableUPnPfunction.

Then enter IP camera’s ‘UPnP Settings’ to enable UPnP and make sure the state is ‘UPnP Success’.

•IfyourrouterhastheVirtualMapfunction,enterroutersettingpage,addthecamera’sIPaddress

and port number to the Virtual map list.

How to use DDNS

When you use ADSL, the IP Camera will connect to the Internet through ADSL automatically. For

each ADSL reconnection, your Internet Service Provider will re-assign a new IP address for the IP

Camera to facilitate the access. DDNS (Dynamic Domain Name Server) can map the dynamic IP

address of an IP Camera to a fixed domain name. Therefore, we can access the IP Camera by the

fixed domain name whether the IP address changes or not. The IP address is not necessary when

using the DDNS via the domain name to find your network.

1. Go to the website which provides free domain names such as http://www.dyndns.com and

2. Enter DDNS Settings Page and enable the DDNS service and click ‘Submit’ to reboot the camera.

3. Re-Login to the Camera web browser as Administrator and enter the ”DDNS Service.

Settings”page to check if the DDNS Status is DynDNS Succeed.

4. Enter the ‘UPnP Settings’ page, the UPnP Status should be ‘UPnP Succeed’. If not, then enter

‘Basic Network Settings’ page to change HTTP Port details. Then click “SUBMIT” and reboot Device.

5. Re-login to the Camera homepage to check and make sure the DDNS Status and UPnP Status

are working.

6. You only need to enter the domain name (Domain name+Port number http://ipcam.domain.

net:81) in the IE address bar, the browser will visit the IP Camera. Wait for several minutes and the

ACCESSING THE WIFI CAMERA continued

IP Camera will access the Internet automatically.

Another way the user can access the IP camera from a WAN is by using the DDNS domain name.

If the gateway settings and DDNS settings have been completed, enter the DDNS dynamic domain

name (for example,http://ipcam.vicp.net, do not add www.) in the address bar of IE to access the IP

Camera. If multiple IP Cameras are connected to the same router, enter DDNS dynamic domain with

the port number (for example, http://ipcam.vicp.net:85) in the address bar of IE to access different IP

cameras.

Accessing the IP Camera from an iPhone

1. Go to your web broswer and enter the IP address of the camera.

ACCESSING THE WIFI CAMERA continued

2. Login as “admin” and enter your password.

3. Camera recording image displays as shown in the picture below.

Page is loading ...

SKYTRONIC 351.148 IP Camera, IP391W, IP601W User manual

Other documents