Chicago Electric 46804 User manual

Brand: Chicago Electric

Model: 46804

Category: Power tools

Type: User manual

Chicago Electric 46804 is a powerful and versatile tool that makes drilling tasks a breeze. With its 3.8 amp motor and 2800 RPM no-load speed, it can handle a variety of drilling tasks in both wood and metal. The keyed chuck allows for quick and easy bit changes, while the reversible feature provides added convenience.

Model 46804

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

3/8” SINGLE SPEED, ELECTRIC DRILL

SKU 46804 For technical questions, please call 1-800-444-3353. Page 2

PRODUCT SPECIFICATIONS

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures, parts list and as-

sembly diagram. Keep your invoice with this manual. Write the invoice number

on the inside of the front cover. Keep this manual and invoice in a safe and dry

place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in

electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

2. Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from

debris such as chips and sparks. Provide barriers or shields as needed.

Power Requirements 120 VAC, 60 Hz, Single Phase, 3.8 Amps

No Load Speed 2800 RPM

Drilling Capacity Wood - 1”, Metal - 3/8”

Weight 2.8 Lbs.

Features: Reversible, Single Speed, Fan-Cooled Motor, Keyed Chuck.

E194601

SKU 46804 For technical questions, please call 1-800-444-3353. Page 3

ELECTRICAL SAFETY

4. Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter

plugs. Check with a qualified electrician if you are in doubt as to whether

the outlet is properly grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to carry electricity away

from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is

wider than the other). This plug will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet, reverse the plug. If it still does not

fit, contact a qualified electrician to install a polarized outlet. Do not

change the plug in any way. Double insulation eliminates the need for the

three wire grounded power cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators,

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools

or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords immedi-

ately. Damaged Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These extension cords are rated for outdoor use, and

reduce the risk of electric shock.

PERSONAL SAFETY

10. Stay alert. Watch what you are doing, and use common sense when oper-

ating a power tool. Do not use a power tool while tired or under the influ-

ence of drugs, alcohol, or medication. A moment of inattention while operat-

ing power tools may result in serious personal injury.

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose

clothes, jewelry, or long hair can be caught in moving parts.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 4

12. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Carrying power tools with your finger on the Trigger invites accidents.

13. Remove adjusting keys or wrenches before turning the power tool on. A

wrench or a key that is left attached to a rotating part of the power tool may result

in personal injury.

14. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the power tool in unexpected

situations.

15. Use safety equipment. Always wear ANSI approved eye protection. Dust

mask, non-skid safety shoes, hard hat, or hearing protection must be used for

appropriate conditions.

TOOL USE AND CARE

16. Use clamps (not included) or other practical ways to secure and support

the workpiece to a stable platform. Holding the work by hand or against your

body is unstable and may lead to loss of control.

17. Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

18. Do not use the power tool if the Trigger does not turn it on or off. Any tool

that cannot be controlled with the Power Switch is dangerous and must be re-

placed.

19. Disconnect the Power Cord Plug from the power source before making any

adjustments, changing accessories, or storing the tool. Such preventive

safety measures reduce the risk of starting the tool accidentally.

20. Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

21. Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with a sharp cutting bits are less likely to bind and are easier

to control. Do not use a damaged tool. Tag damaged tools “Do not use” until

repaired.

22. Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool’s operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly main-

tained tools.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 5

23. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

SERVICE

24. Tool service must be performed only by qualified repair personnel. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

25. When servicing a tool, use only identical replacement parts. Follow

instructions in the

“Inspection, Maintenance, And Cleaning”

section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions

may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

1. Hold tool by insulated gripping surfaces when performing an operation

where cutting tools may contact hidden wiring or its own cord. Contact

with a ‘live’ wire will make exposed metal parts on the tool ‘live’ and shock

the operator.

2. Maintain labels and nameplates on the Drill. These carry important informa-

tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.

3. Always wear safety impact goggles and heavy work gloves when using the

Drill. Using personal safety devices reduce the risk for injury. Safety impact eye

goggles and heavy work gloves are available from Harbor Freight Tools.

4. Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of

obstructions, grease, oil, trash, and other debris. Do not use a power tool in

areas near flammable chemicals, dusts, and vapors. Do not use this product in a

damp or wet location.

5. Make sure to read and understand all instructions and safety precautions

as outlined in the manufacturer’s manual for the drill.

6. When using a hand-held power tool, always maintain a firm grip on the tool

with both hands to resist starting torque.

7. Always keep the extension cord away from moving parts on the tool.

8. Avoid unintentional starting. Make sure you are prepared to begin work

before turning on the Drill.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 6

9. Make sure the Drill bit being used is free from burrs and any other foreign

matter which could damage the tool.

10. Never leave the Drill unattended when it is plugged into an electrical outlet.

Turn off the tool, and unplug it from its electrical outlet beforeleaving.

11. Always unplug the Drill from its electrical outlet before performing and

inspection, maintenance, or cleaning procedures.

12. Let Bits cool before touching changing or adjusting them. Bits heat up

dramatically while in use, and are capable of severe burns.

13. Do not force the Drill. This tool will do the work better and safer at the speed

and capacity for which it was designed.

14. Always secure the workpiece in a vise or other appropriate device; never

attempt to hold the workpiece in your hand while drilling.

15. WARNING! People with pacemakers should consult their physician(s) before

using this product. Electromagnetic fields in close proximity to a heart pace-

maker could cause interference to or failure of the pacemaker.

16.

WARNING! Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities, contain chemicals known (to the State of Califor-

nia) to cause cancer, birth defects or other reproductive harm. Some examples

of these chemicals are: lead from lead-based paints, crystalline silica from bricks

and cement or other masonry products, arsenic and chromium from chemically

treated lumber. Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these chemicals: work in a

well ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to filter out microscopic particles.

(California Health & Safety Code 25249.5, et seq.)

SKU 46804 For technical questions, please call 1-800-444-3353. Page 7

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualified electrician if you are in doubt as to whether the

outlet is properly grounded. Do not modify the power cord plug provided with

the tool. Never remove the grounding prong from the plug. Do not use the

tool if the power cord or plug is damaged. If damaged, have it repaired by

a service facility before use. If the plug will not fit the outlet, have a proper

outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of elec-

tric shock. (See Figure A.)

2. The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached

to an electrically “live” terminal. (See Figure A.)

3. Your tool must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet

should look like those in the following illustration. (See Figure A.)

FIGURE A

SKU 46804 For technical questions, please call 1-800-444-3353. Page 8

FIGURE B

4. Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisfies OSHA requirements and complies with

the applicable standards of Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical Code. (See Figure B.)

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

EXTENSION CORDS

Grounded

tools require a three wire extension cord.

Double Insulated

tools

can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool damage.

(See Figure C, next page.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure C.)

4. When using more than one extension cord to make up the total length, make

sure each cord contains at least the minimum wire size required.

(See Figure C.)

5. If you are using one extension cord for more than one tool, add the nameplate

amperes and use the sum to determine the required minimum cord size.

(See Figure C.)

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

Note: This Drill has a Two Prong Plug.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 9

6. If you are using an extension cord outdoors, make sure it is marked with the

suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified

electrician before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or

wet areas.

SYMBOLOGY

Double Insulated

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current

Amperes

No Load Revolutions

per Minute (RPM)

xxxx/min.

V ~

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 VOLT)

NAMEPLATE

AMPERES

(At Full Load)

EXTENSION CORD LENGTH

25 FEET 50 FEET 75 FEET 100 FEET 150 FEET

0 - 2.0 18 18 16 16 16

2.1 - 3.4 18 18 16 14 14

3.5 - 5.0 18 18 16 14 12

5.1 - 7.0 18 16 14 12 12

7.1 - 12.0 16 14 12 10 -

12.1 - 16.0 14 12 10 - -

16.1 - 20.0 12 10 - - -

FIGURE C

*Based on limiting the line voltage drop

to five volts at 150% of the rated amperes.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 10

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on page 14

are included. If any parts are missing or broken, please call Harbor Freight Tools at the

number shown on the cover of this manual as soon as possible.

OPERATING INSTRUCTIONS

NOTE: For additional information regarding the parts listed in the following pages, refer

to the

Assembly Diagram on page 15.

Warning!! Always wear ANSI approved safety glasses and full face

shield when operating your Drill. Failure to do so could result in dust,

shavings, or loose particles being thrown into your eyes.

CAUTION: Always make sure the Power Cord of the Drill is unplugged from its

electrical outlet

prior

to making any adjustments to the tool.

FIGURE 1

Chuck (10)

Put Chuck Key

(22)Here

Level

Trigger (4)

Forward/Reverse

Lever

Chuck Key (22)

Lock

SKU 46804 For technical questions, please call 1-800-444-3353. Page 11

FIGURE 2

Chuck Key (22) in hole.

Jaws

Using the Lock Button

When you are drilling for

extended times and want to

take your finger off of the

Trigger, use the Lock Button.

Squeeze the Trigger to start the

drill, then push the Lock Button.

The drill will stay on. When you

are finished, just squeeze and

release theTrigger to stop the

drill.

See FIGURE 1 on page 10.

To Install Bits: See FIGURE 1 on page ten and FIGURE 2 below.

1. Insert the Chuck Key (22) in one of the holes on the Chuck (10) and turn it coun-

terclockwise to open the jaws of the Chuck (10).

2. Insert a bit (not included). Keep the bit straight as you turn the Chuck Key (22)

clockwise to close the jaws of the Chuck (22). Once tightened, visually check to

see if it is in straight. If not, repeat the process and straighten the bit. When it is

straight, use the Chuck Key (22) to tighten the Chuck (10).

3. To remove a bit (not included), insert the Chuck Key (22) in a Chuck Hole and

turn it counterclockwise until the jaws open and release the bit.

OPERATING INSTRUCTIONS (continued)

Note: Always use sharp bits. Dull or damaged bits may cause undue stress on the

drill and possibly break, causing injury. Bits are available at Harbor Freight

Tools.

Note: When holding the drill in your hand, the Forward/Reverse Lever points to-

ward the right and the unit will drill forward. When it is pointed to the left, the

unit will drill in reverse. See FIGURE 1 on page 10. The Forward/Reverse

Lever does not act as a locking mechanism. To lock Trigger, see “Using the

Lock Button” above.

Note: To ensure you are drilling or driving screws on a level plane, use the built-in

level on the top of the Drill.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 12

OPERATING INSTRUCTIONS (continued)

When drilling wood: Place the bit at the point to be drilled. If you are drilling a

hard, smooth surface, use a punch to mark the drill location. Set the Forward/

Reverse Lever to forward (right). Grasp the handle firmly and slowly squeeze the

Trigger (4). Never force the tool. Only apply light pressure when drilling. To stop

drilling, release the Trigger. Note: The further you pull back on the Trigger (4), the

faster the bit will rotate. Maximum drilling depth capacity for wood is 1 inch.

Metal Drilling: Always wear work gloves when handling sheet metal.

Always clamp sheet metal. Use a punch to mark the position of the hole. When

used, light machine oil wil prolong the life of the bit and increase drilling action.

With steel, use oil as a lubricant; aluminum, use turpentine or paraffin; brass, cop-

per and cast iron, use no lubricant. Do not force the tool. Start slowly and let the

weight of the tool do the job. Apply only light pressure for horizontal drilling.

Maximum drilling depth capacity for metal is 3/8 of an inch.

Plastic and plastic coated chipboard:

Use high speed steel drill bits and refer to the wood drilling section on this page.

Warning! If the drill abnormally shakes,

gets hot, smokes and smells, sparks, or

the jaws of the Chuck (10) get stuck in a

workpiece, cut off the power supply and

have the Drill inspected by a qualified

service technician.

Warning! If the bit jams in a workpiece,

or if the drill stalls, stop the tool and

immediatly inplug it. Determine the reason

for jamming before resuming. To remove

a bit, reverse the direction by turning the

Forward/Reverse Lever to the left.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 13

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Make sure that the tool is unplugged from its electrical outlet

before performing any inspection, maintenance, or cleaning procedures.

2. BEFORE EACH USE, inspect the general condition of the Drill. Check for loose

screws, misalignment or binding of moving parts, cracked or broken parts, dam-

aged electrical wiring, and any other condition that may affect its safe operation.

If abnormal noise or vibration occurs, have the problem corrected before further

use. Do not use damaged equipment.

3. Periodically check the mounting screws and tighten if necessary.

4. Clean the unit with a damp cloth. Never use solvents to clean the unit.

5. Inspect the chuck and remove any dirt or debris.

6. The following should only be done by a qualified service technician. Inspect the

Carbon Brushes (17) periodically. See the Assembly Drawing on page 15. Re-

move the Brush Holder (16) on the side of the drill. Take the Carbon Brush (17)

out of the Brush Holder (17). If it is dirty, use a pencil eraser to clean it. If it is

worn, replace it and insert the Carbon Brush (17) into the Brush Holder (17). If

one brush is bad, replace both.

SKU 46804 For technical questions, please call 1-800-444-3353. Page 14

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

PLEASE READ THE FOLLOWING CAREFULLY

PARTS LIST

Part No. Description

1 Rubber Grip

2 Blister

3 Right Cover

4 Trigger

5 Fender Ring

6 Circle Key

7 Slip Bearing

8 Cogwheel

9 Bearing

10 Chuck

11 Spindle

12 Rolling Bearing

13 Rotor

14 Bearing

15 Stator

16 Brush Holder

17 Carbon Brush

18 Screw

19 Terminal Plate

20 Cord Sheath

21 Left Cover

22 Chuck Key

SKU 46804 For technical questions, please call 1-800-444-3353. Page 15

NOTE: Some parts are listed and shown for illustration purposes only, and are not

available individually as replacement parts.

ASSEMBLY DIAGRAM

The Chuck Key (22) is not shown.

Chicago Electric 46804 User manual

Brand: Chicago Electric

Model: 46804

Category: Power tools

Type: User manual

Download PDF

report

Chicago Electric 46804 User manual

Chicago Electric 46804 User manual

Related papers

Other documents