Model No. 831.15906.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
• Assembly
• Operation
• Maintenance
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Sears, Roebuck and Co.
Hoffman Estates, IL 60179
WEIGHT BENCH EXERCISER
Userʼs Manual
2
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
B
EFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PART LIST AND EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
90-DAY FULL WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
TABLE OF CONTENTS
This drawing shows the location(s) of the warning decal(s).
If a decal is missing or illegible, call 1-877-992-5999
and request a free replacement decal. Apply the decal
in the location shown. Note: The decal(s) may not be
shown at actual size.
3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your weight bench before using your weight bench.
Sears assumes no responsibility for personal injury or property damage sustained by or through
t
he use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench.
3. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
4. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
5. Keep the weight bench indoors, away from
moisture and dust. Do not put the weight
bench in a garage or covered patio or near
water.
6. Place the weight bench on a level surface,
with a mat beneath it to protect the floor or
carpet. Make sure that there is enough clear-
ance around the weight bench to mount, dis-
mount, and use the weight bench.
7. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
8. Keep children under age 12 and pets away
from the weight bench at all times.
9. The weight bench is designed to support a
maximum user weight of 300 lbs. (136 kg)
and a maximum total weight of 410 lbs. (186
kg). Do not use more than 110 lbs. (50 kg) of
weight with the weight bench. Note: The
weight bench does not include weights.
10. Wear appropriate exercise clothes while
exercising; do not wear loose clothes that
could become caught on the weight bench.
Always wear athletic shoes for foot protec-
tion.
11. Always make sure that the locking pin is
fully inserted into the frame and into the
pivot bracket before you use the weight
bench.
12. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
4
Backrest
Front Leg
Locking Pin
Pivot Bracket
Foam Pad
Seat
BEFORE YOU BEGIN
T
hank you for selecting the versatile WEIDER PRO™
255 L weight bench. The 255 L weight bench is
designed to help develop the major muscle groups of
the upper body. Whether your goal is to tone your
b
ody, build dramatic muscle size and strength, or
improve your cardiovascular system, the weight bench
will help you to achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
r
eading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
d
ecal are shown on the front cover of this manual.
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
Length: 3 ft. 4 in. (102 cm)
Width: 1 ft. 6 in. (46 cm)
5
M10 x 63mm Bolt (16)
M10 x 85mm Bolt (23)
M10 x 70mm Bolt (26)
M6 Washer (22)
M10 Locknut (19)
M10 Washer (20)
M10 x 63mm Carriage Bolt (18)
M6 x 60mm Screw (17)
M10 Large Washer (27)
M6 x 16mm
Screw (24)
M10 x 20mm
Bolt (25)
M4 x 16mm
Screw (28)
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST near the end of this manual. IMPORTANT: If you cannot find a
part in the hardware kit, check to see if it has been preassembled. If a part is missing, please call 1-877-
992-5999.
6
ASSEMBLY
1.
Orient the Front Stabilizer (29) so that the warn-
ing decals are facing upward.
Attach the Front Stabilizer (29) to the Front Leg
(2) with two M10 x 63mm Carriage Bolts (18)
and two M10 Locknuts (19). Do not tighten the
Locknuts yet.
2. Attach the Front Leg (2) to the Frame (1) with
two M10 x 63mm Bolts (16), two M10 Large
Washers (27), and two M10 Locknuts (19). Do
not tighten the Locknuts yet.
1
2
19
19
Warning
Decals
18
2
1
19
19
16
27
27
2
29
To make assembly easier, read the
assembly tips in the box above.
•
Assembly requires two persons.
• Because of its size and weight, assemble the
weight bench in the location where it will be used.
M
ake sure that there is enough clearance to walk
around the weight bench as you assemble it.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you complete all assembly steps.
• To identify small parts, see page 5.
•
The following tools (not included) may be required
for assembly:
two adjustable wrenches
one rubber mallet
one standard screwdriver
one Phillips screwdriver
Assembly will be more convenient if you have a
set of wrenches. To avoid damaging parts, do not
use power tools.
7
3. Orient the Rear Leg (3) as shown.
Attach the Rear Stabilizer (4) to the Rear Leg
(
3) with two M10 x 63mm Carriage Bolts (18)
and two M10 Locknuts (19). Do not tighten the
L
ocknuts yet.
4. Attach the Rear Leg (3) to the Frame (1) with
two M10 x 20mm Bolts (25) and two M10
Washers (20).
See steps 1–3. Tighten the M10 Locknuts (19).
5. Insert the two Pad Tubes (10) into the Front Leg
(2).
Wet the ends of the Pad Tubes (10) with soapy
water, and slide two Foam Pads (9) onto each
Pad Tube.
Then, press a Pad Cap (11) into each Foam
Pad (9).
3
19
19
4
18
3
4
2
9
11
11
10
10
11
9
9
20
20
25
3
1
5
8
8. Orient the Backrest (7) as shown. Attach the
Backrest to the Backrest Frame (5) with four M6
x 16mm Screws (24).
See the inset drawing. Attach the tether on the
Locking Pin (21) to the underside of the Frame
(1) with an M4 x 16mm Screw (28). Then, insert
the Locking Pin into the Frame and into an
adjustment hole in the Pivot Bracket (6).
7
7. Apply some of the included grease to an M10 x
85mm Bolt (23).
Insert the Pivot Bracket (6) into the slot in the
Frame (1). Attach the Backrest Frame (5) to the
Frame with the M10 x 85mm Bolt (23) and an
M10 Locknut (19). Do not overtighten the
Locknut; the Backrest Frame must pivot
easily.
Then, attach an M10 x 20mm Bolt (25) and an
M10 Locknut (19) to the hole in the end of the
Pivot Bracket (6).
See step 6. Tighten the M10 Locknuts (19).
23
19
19
5
6
Grease
7
5
24
24
6. Attach the Pivot Bracket (6) to the Backrest
Frame (5) with two M10 x 70mm Bolts (26) and
two M10 Locknuts (19). Do not tighten the
L
ocknuts yet.
6
19
26
6
5
1
8
25
21
1
6
28
9
ADJUSTING THE BACKREST
The Backrest (7) can be used in a declined posi-
tion, a level position, or any of four inclined posi-
tions.
To adjust the Backrest (7), first remove the Locking
Pin (21) from the Frame (1). Then, pivot the
Backrest to the desired position, and reinsert the
Locking Pin into the Frame and into an adjustment
hole in the Pivot Bracket (6).
7
21
6
1
Adjustment
Holes
ADJUSTMENT
WARNING: Make sure that the
Locking Pin (21) is fully inserted into the
Frame (1) and into the Pivot Bracket (6).
See the EXERCISE GUIDELINES on page 10 for important exercise information, and refer to the accompanying
exercise guide to see the correct form for several exercises.
Make sure that all parts are properly tightened each time the weight bench is used. Replace any worn parts
immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent; do not
use solvents to clean the weight bench.
9. Attach the Seat (8) to the Frame (1) with four
M6 x 60mm Screws (17) and four M6 Washers
(22).
1
8
17
22
9
10. Make sure that all parts are properly tight-
ened before you use the weight bench.
22
10
EXERCISE GUIDELINES
FOUR TYPES OF STRENGTH WORKOUTS
Note: A “repetition” is one complete cycle of an exer-
c
ise, such as one sit-up. A “set” is a series of repeti-
tions.
Muscle Building—Work your muscles near their max-
imum capacity and progressively increase the intensity
of your exercise. Adjust the intensity level of an individ-
ual exercise as follows:
• Change the amount of resistance used.
• Change the number of repetitions or sets performed.
Use your own judgment to determine the amount of
resistance that is right for you. Begin with 3 sets of 8
repetitions for each exercise you perform. Rest for 3
minutes after each set. When you can complete 3 sets
of 12 repetitions without difficulty, increase the amount
of resistance.
Toning—Tone your muscles by working them to a
moderate percentage of their capacity. Select a mod-
erate amount of resistance and increase the number
of repetitions in each set. Complete as many sets of
15 to 20 repetitions as possible without discomfort.
Rest for 1 minute after each set. Work your muscles
by completing more sets rather than by using high
amounts of resistance.
Weight Loss—To lose weight, use a low amount of
resistance and increase the number of repetitions in
each set. Exercise for 20 to 30 minutes, resting for a
maximum of 30 seconds between sets.
Cross Training—Combine strength training and aero-
bic exercise by following this type of program:
• Strength training workouts on Monday, Wednesday,
and Friday.
• 20 to 30 minutes of aerobic exercise on Tuesday
and Thursday.
• One full day of rest each week to give your body
time to regenerate.
WORKOUT GUIDELINES
Familiarize yourself with the equipment and learn the
proper form for each exercise. Use your own judgment
to determine the appropriate length of time for each
workout, and the numbers of repetitions and sets to
complete. Progress at your own pace and be sensitive
to your bodyʼs signals. Follow each workout with at
l
east one day of rest.
W
arming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Working Out—Include 6 to 10 different exercises in
each workout. Select exercises for every major muscle
group, emphasizing areas that you want to develop. To
give balance and variety to your workouts, vary the
exercises from workout to workout.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FORM
Move through the full range of motion for each exer-
cise and move only the appropriate parts of the body.
Perform the repetitions in each set smoothly and with-
out pausing. The exertion stage of each repetition
should last about half as long as the return stage.
Exhale during the exertion stage of each repetition and
inhale during the return stroke. Never hold your
breath.
Rest for a short period of time after each set:
• Muscle Building—Rest for three minutes after each
set.
• Toning—Rest for one minute after each set.
• Weight Loss—Rest for 30 seconds after each set.
STAYING MOTIVATED
For motivation, keep a record of each workout. Write
the date, the exercises performed, the resistance
used, and the numbers of sets and repetitions com-
pleted. Record your weight and key body measure-
ments once a month. To achieve good results, make
exercise a regular and enjoyable part of your life.
11
21
1
4
12
12
18
19
3
19
20
20
25
13
19
23
13
19
19
16
22
22
17
17
8
14
9
9
2
9
10
29
12
12
19
18
19
7
15
5
24
6
26
19
19
25
28
9
24
10
27
27
11
11
11
PART LIST/EXPLODED DRAWING Model No. 831.15906.0 R1011A
Key No. Qty. Description Key No. Qty. Description
11Frame
2
1 Front Leg
31Rear Leg
41Rear Stabilizer
51Backrest Frame
61Pivot Bracket
71Backrest
81Seat
94Foam Pad
10 2 Pad Tube
11 4 Pad Cap
12 4 50mm Round Outer Cap
13 4 50mm Square Inner Cap
14 1 45mm Square Inner Cap
15 1 25mm x 50mm Inner Cap
16 2 M10 x 63mm Bolt
17 4 M6 x 60mm Screw
18 4 M10 x 63mm Carriage Bolt
1
9 10 M10 Locknut
20 2 M10 Washer
21 1 Locking Pin
22 4 M6 Washer
23 1 M10 x 85mm Bolt
24 4 M6 x 16mm Screw
25 3 M10 x 20mm Bolt
26 2 M10 x 70mm Bolt
27 2 M10 Large Washer
28 1 M4 x 16mm Screw
29 1 Front Stabilizer
*
– Userʼs Manual
*
– Exercise Guide
*
– Grease Packet
Note: Specifications are subject to change without
notice. For information about ordering replacement
parts, see the back cover of this manual. *These
parts are not illustrated. If a part is missing,
please call 1-877-992-5999.
Part No. 302908 R1011A Printed in China © 2011 ICON IP, Inc.
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
®
(1-888-784-6427)
Get it fixed, at your home or ours!
® Registered Trademark /
TM
Trademark /
SM
Service Mark of Sears Brands, LLC
® Marca Registrada /
TM
Marca de Fábrica /
SM
Marca de Servicio de Sears Brands, LLC
90-DAY FULL WARRANTY
If this Sears WEIGHT BENCH EXERCISER fails due to a defect in material or workmanship within 90
days of the date of purchase, call 1-800-4-MY-HOME
®
(1-800-469-4663) to arrange for free repair (or
replacement if repair proves impossible).
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental
purposes. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Weider 255 L 831.15906.0 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Weider PRO 255 L BENCH WEBE49310 Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Alaterre Furniture AWAA033320 Operating instructions
-
ProForm 831.150320 User manual
-
-
-
Pro-Form C840 User manual
-
-
-
-
-
ProForm PFEVBE3805 Owner's manual