Ariston ASL 70 CX User manual

Contents

TUMBLE DRYER

ASL70C

ASL70CX

Instruction booklet

Installation, 2

Door reversal instructions

Where to put your dryer

Ventilation

Water drain

Electrical connection

Before you start using your dryer

Dryer description, 3

To open the door

The features

Control panel

Start and programmes, 4-6

Choosing a programme

Table of programmes

The controls

Laundry, 7-8

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 9

General safety

Disposal

Saving energy and respecting the environment

Maintenance and Care, 10

Switching off the electricity

Cleaning the filter after each cycle

Empty the water container after each cycle

Check the drum after each cycle

Cleaning the condenser unit

Cleaning the dryer

Troubleshooting, 11

Service, 12

Spare parts

GB

English, 1

I

Italiano, 13

F

Français, 25

D

Deutsch, 37

E

Español, 49

NL

Nederlands, 73

P

Português, 61

GB

1

Installation

2

GB

! Keep this instruction booklet on hand in order to refer to

it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another

party, make sure that this booklet is supplied along

with the dryer so that the new owner may be informed

about warnings and suggestions on how the dryer

works.

! Read these instructions carefully; the following

pages contain important information on installation

and suggestions on how the appliance works.

Door Reversal Instructions

The door of your dryer is reversible and can easily be

changed. Exchange diagonally hinge brackets and

blanking screws. Exchange door latch and catch with

their opposite blanking plates (see diagram above).

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the appliance under a

work counter, be sure to leave a 10mm space

between the top and any other objects on or

above the machine and a 15mm space between the

sides and lateral furnishings or walls. This is to ensure

proper air circulation. Make sure that the back vents

are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

Door catch

Door latch

Hinge

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

! If using the dryer in a small or cold room some

condensation could be experienced.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. Simply remove the top hose

from its top fitting at the rear of the dryer and plumb the

hose provided to the drain.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the

socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power cord supplied should be checked

periodically and replaced by a cord specially prepared

for this dryer and fitted only by authorised technicians

(see Service). New or longer power cords are supplied

at an extra charge by authorised dealers.

! The manufacturer denies any responsibility should any

of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

GB

3

replacing the empty water container, the dryer must be

running for this to happen (see The Controls).

The On/Off indicator light signals that your dryer

is in use or ready to select a programme. If this light

flashes it indicates there is a fault (see Troubleshooting).

The ON/OFF button : If the dryer is running and

this button is pressed, the dryer stops. Press again,

the dryer restarts.

The Progress or Delay lights show you the status of

the programme, or the delay time when they flash.

During a delayed start the lights flash to show the

delay selected. When (not flashing) they show each

stage of the programme by the corresponding light

turning on (see Start and Programmes).

The PROGRAMMES knob sets the programme:

rotate it until the indicator is pointing to the programme

you want to select (see Start and Programmes).

The START/CANCEL button starts a selected

programme. When you press this button there will be

one beep and the progress lights will flash to confirm

the action. If you have not set a programme, the buzzer

will beep four times. When a programme is running,

holding this button cancels the programme and stops

the dryer (see Start and Programmes).

The OPTION buttons select available options for your

selected programme (see Start and Programmes).

The Option lights indicate that the option has been

selected by the button to the left of the appropriate

light.

The Drying Guide allows you to consult a user friendly

table of fabric types and load capacities.

The Empty Water indicator light signals that the

water container should be emptied. When it is flashing

it indicates that the container is full.

The light will take a few seconds to go out after

Control panel

Dryer Description

To open the door The features

Press and release the front

panel in position shown

Water container

Air intake

grille

Rating plate

Door catch

Filter

Door latch

Model &

Serial

numbers

Condenser cover handle

(Pull to open)

Condenser cover

Empty Water

Light

Drying Guide

PROGRAMMES

Knob

START/CANCEL

Button

Indicator

Progress or Delay

Lights

OPTION

Buttons

Option

Lights

On/Off

Light

ON/OFF

Button

4

GB

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place and the water container is empty

and in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If the On/Off light is not lit: Press the ON/OFF

button .

6. Choose a programme by checking the Programmes

Guide (see Programmes) as well as the indications

for each type of fabric (see Laundry).

- Select a programme by rotating the

PROGRAMMES knob.

7. Set a delay time and other options if necessary.

8. If you wish to select the buzzer sound, at the end

of the programme, press the ALARM Option button.

9. Press the START button to begin.

During the drying programme, you can check on

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START button in order

to resume drying.

10. During the last few minutes of Drying

Programmes, before the programme is

completed, the final COOL TUMBLE phase is

entered (fabrics are cooled), this phase should

always be allowed to complete.

11. When the programme is complete. The buzzer

will sound if Alarm option was selected.

Open the door, take the laundry out, clean the filter

and replace it. Empty the water container and

replace it (see Maintenance).

If the Post Creasecare option has been selected

and you do not remove the laundry immediately,

the dryer will tumble occasionally for 10 hours or

until you open the door.

12. Unplug the dryer.

Start and Programmes

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The

cycle relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity.

These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put

them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton

mix, and less well on acrylic fibres and on materials such as Tencel®.

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

GB

5

Start and Programmes

Programmes

Programme

What it does... How to set it...

Note:

Easy

Iron

Brief programme (approximately

10 minutes) that softens fibres of

clothing that is ready for ironing.

! This is not a drying

programme (see previous

page).

Options available:

Alarm

1. Position the PROGRAMMES knob

on .

2. Select any options if required.

3. Press the START button.

Options available:

Alarm

1. Position the PROGRAMMES knob

on .

2. Select any options if required.

3. Press the START button.

Options available:

Alarm, Delayed Start,

Pre-Creasecare,

Post Creasecare.

1. Position the PROGRAMMES knob

on 3.

2. Select any options if required.

3. Press the START button.

Options available:

Alarm, Delayed Start,

Pre-Creasecare,

Post Creasecare.

1. Position the PROGRAMMES knob

on

1.

2. Select any options if required.

3. Press the START button.

Options available:

Alarm, High Heat, Delayed

Start, Pre-Creasecare,

Post Creasecare.

Consult ‘suggested drying

times’ (see Laundry).

The last 10 minutes of these

programmes is the Cool

Tumble phase, see below.

1. Position the PROGRAMMES knob

on the desired time: 160, 140, 120,

100, 90, 70, 60, 50, 40 or 30.

2. Select any options if required.

3. Press the START button.

Cottons

Cupboard

dry

Dries your clothes on High Heat

setting, ready for putting away.

Timed Drying

(160, 140, 120,

100, 90, 70, 60,

50, 40 or 30

minutes)

Dries wet clothing that you wish

to dry on Low Heat or small

loads (less than 1kg).

Can be used with High Heat

option if you prefer to use a

timed programme.

Brief programme (approximately

10 minutes) that cools fibres of

clothing.

Synthetics

Cupboard

dry

Cool Tumble

Dries your clothes on Low Heat

setting, ready for putting away.

! If the On/Off light is not lit; Press the ON/OFF button and then select programme.

Options available:

Alarm, Delayed Start,

Pre-Creasecare,

Post Creasecare.

1. Position the PROGRAMMES knob

on

2.

2. Select any options if required.

3. Press the START button.

Cottons

Hanger

dry

Dries your clothes on High Heat

setting, ready for hanging.

6

GB

Alarm

Available on all programmes and allows the buzzer to

give a signal at the end of the drying cycle, to remind

you that the clothes are ready to be removed.

Press the button and the light will show that the option

is selected.

Post Creasecare

The clothes are occasionally tumbled after the end of

the drying and cool tumble cycles, to help prevent

creases developing should you not be available to

remove the load immediately the programme is complete.

Empty Water Light / Container

(If you have plumbed your dryer to a drain this light

can be ignored, as there is no need to empty the water

container).

When this light is on (not flashing) it reminds you to

empty the water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the light flashes and the buzzer sounds.

After this it stops and all 3 progress lights and the 3hr

delay light come on and the empty water light flashes.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer, the light will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the

dryer and have the following effects:

●

All 3 progress lights and the 3hr delay light come on.

●

During a delay phase the delay will continue to

count down. The start button must be pressed to

resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

●

The start button must be pressed to resume the

programme. The progress lights will change to

show the current status.

●

During the cool tumble or post creasecare phase

of a drying programme and anytime during an

Airing or Cool Tumble programme, the

programme will finish. Pressing the start button

will re-start a new programme at the beginning.

●

Changing the programmes knob will select a new

programme, after you press the start button. You

can use this to select the Cool Tumble

programme to cool the clothes, if you find them

dry enough.

●

Note

If you have a power cut, switch off the power or

remove the plug, press the START button and the

programme will resume.

●

PROGRAMMES knob

! Warning, if after pressing the start button, the

programmes knob position has changed, the new

position will NOT change the programme selected.

! Position 0, turning the knob to position 0 resets and

cancels a programme.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programmes knob before

an option can be selected. Not all options are available

for all programmes (see Start and Programmes). If an

option is not available and you press the button, the

buzzer will beep four times. If the option is available

there will be one beep and the option light next to the

button lights to confirm the selection.

Progress ( Drying, Cool Tumble, Post

Creasecare) / Delay (3hr, 6hr, 9hr, 12hr) Lights

When the light next to the delay button is on, these lights

flash to indicate the delay time is selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 12 hours in 3hr

steps. Ensure the water bottle is emptied before setting

a delayed start.

When a delayed start is in progress the light next to the

delay button will be on and the selected delay period

light will flash (after the start button has been pressed).

To set a delayed start, press the Time Delay button,

and the light next to the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 12hr light is on,

pressing the button again will cancel the delay.

You can also cancel the delay by turning the programmes

knob to 0, wait for the buzzer to beep and then turn

back to your selected programme.

Pre Creasecare

When a delayed start has been selected the clothes

are tumbled occasionally during the delayed period to

help prevent creases developing.

High Heat

When available this button selects high heat. Press this

button and a high heat setting is selected and the light

alongside the button comes on. Timed programmes

have a default of low heat, if the light alongside the

button is on then pressing the button selects a low heat

setting and the light goes out.

The Controls

Start and Programmes

Laundry

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

GB

7

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 7kg max (15lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical load

Clothes

Blouse Cotton 150g 5oz

Other 100g 3oz

Dress Cotton 500g 1lb 2oz

Other 350g 12oz

Jeans 700g 1lb 6oz

10 nappies 1000g 2lb 3oz

Shirt Cotton 300g 10oz

Other 200g 7oz

T-Shirt 125g 4oz

Household Items

Duvet cover Cotton 1500g 3lb 5oz

(Double) Other 1000g 2lb3oz

Large Tablecloth 700g 1lb 6oz

Small Tablecloth 250g 9oz

Tea Towel 100g 3oz

Bath Towel 700g 1lb 6oz

Hand Towel 350g 12oz

Double Sheet 500g 1lb 2oz

Single Sheet 350g 12oz

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

8

GB

Laundry

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

The table below presents APPROXIMATE drying times

in minutes. Weights refer to dry garments:

Cottons

High (full) Heat

Drying times 800-1000rpm in washing machine

Half Load Full Load

1kg 2kg 3kg 4kg 5kg 6kg 7kg

30-40 40-55 55-70 70-80 80-90 95-120120-140

Synthetics

Low (gentle) Heat

Drying times on reduced spin in washing machine

Half Load Full Load

1kg 2kg 3kg

40-50 50-70 70-90

Acrylics

Low (gentle) Heat

Drying times on reduced spin in washing machine

Half Load Full Load

1kg 2kg

40-60 55-75

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

Installation

Description

Start and

Programmes

Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

GB

9

Warnings and Suggestions

! The appliance has been designed and built

according to international safety standards.

These warnings are given for safety reasons and

must be read carefully.

This appliance conforms to the following

EEC Directives:

- 72/23/EEC and 93/68/EEC (Low Voltage Equipment)

- 89/336/EEC, 92/31/EEC and 93/68/EEC

(Electromagnetic Compatibility)

General safety

●

This tumble dryer has been designed for home,

and not professional use.

●

This dryer must be used by adults, and the

instructions in this booklet should be followed carefully.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

The appliance must be installed correctly and

have proper ventilation. The air intake at the front

of the dryer and rear vent behind the dryer should

never be obstructed (see Installation).

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter, water

container and condenser are securely in place

(see Maintenance).

●

Do not use liquid fabric softeners in the dryer, add

it to the final rinse of your wash.

●

Do not overload the dryer (see Laundry for

maximum loads).

●

Do not load items that are dripping wet.

●

Tumble dry items only if they have been washed

with detergent and water, rinsed and been through

the spin cycle. It is a fire hazard to dry items that

HAVE NOT been washed with water.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not dry garments that have been treated with

chemical products.

●

Never dry articles that are contaminated with

flammable substances (petrol, oil, paint, hair

spray, creams, cooking fat or oils).

●

Do not tumble dry rubber, foam rubber, plastic, plastic

foam, nappy pants or liners, polythene or paper.

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Empty the water container after each use (see

Maintenance).

●

Clean the condenser unit after regular intervals

(see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

Recycling and disposal information

As part of our continued commitment to helping the

environment, we reserve the right to use quality recycled

components to keep down customer costs and minimise

material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream.

Old appliances must be collected separately in order

to optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on

the product reminds you of your obligation,

that when you dispose of the appliance it

must be separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

Saving energy and respecting the

environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Maintenance and Care

10

GB

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning the condenser unit

Periodically (every month) remove the condenser unit

and clean any build up of fluff from between the plates

by rinsing it under the tap with cold water.

This should be done with cold water from the rear of

the condenser.

Removing the condenser:

1. Unplug the dryer and open the door.

2. Pull open the condenser cover (see diagram).

Release the three catches by turning 90˚ counter-

clockwise then pull on the grip and remove from

the dryer.

3. Clean the surface of the seals and replace, making

sure that the catches have been secured.

Cleaning the dryer

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically (every 6 months) vacuum the front air

intake grille and vents at the rear of the dryer, to

remove any build up of fluff, lint or dust. Also to

remove accumulation of fluff from the front of the

condenser and filter areas, clean occasionally with

a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Switching off the electricity

! Unplug your dryer when not using it, when cleaning

it and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it

under running water or with your vacuum cleaner.

Should the filter become clogged up, the airflow inside

the dryer will be seriously compromised: drying times

lengthen and you will consume more energy. It may

also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the filter upwards (see diagram).

2. Clean the filter and replace it correctly.

Ensure the filter is fully located flush into the tumble

dryer trim.

! Do not use the dryer without replacing the filter.

Empty the water container after each

cycle

Pull the container out of the dryer and empty it into a

sink or other suitable drain.

Replace the water container securely.

Always check and empty the container before you

start a new drying programme.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Water container

Handle

Condenser cover

Catches

Air intake

Filter

Tap

Rear

Front

Condenser unit

Troubleshooting

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

Empty water light is flashing

but the dryer has only been

running for a short period.

Empty water light is on and

the water container is not full.

The ON/OFF light flashes to

indicate a fault.

Programme finishes and

clothes are damper than

expected.

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The PROGRAMMES knob has not been set properly (see Start and

Programmes).

●

The START button has not been pressed (see Start and Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes, and see Laundry).

●

The water container needs emptying? The empty water light is flashing?

(see Maintenance).

●

The condenser needs cleaning? (see Maintenance).

●

The correct drying time has not been selected for the load (see Laundry).

●

The air intake grille or rear vents are obstructed (see Installation, and see

Maintenance).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

●

The water container was probably not emptied at the start of the programme.

Do not wait for the empty water signal, always check and empty the

container before starting a new drying programme (see Maintenance).

●

This is normal, the light flashes when the container is full. If the light is on

but not flashing it is just a reminder to empty the container (see Start and

Programmes).

●

If the ON/OFF light flashes together with the Time Delay and High Heat

lights; Or the ON/OFF light flashes together with the Time Delay, Alarm,

High Heat and Empty Water lights, then:

- Turn off and remove the plug. Clean the filter and the condenser

(see Maintenance). Then replace the plug, turn on and start another

programme. If the same combination of lights still flash contact the

Service Centre (see Service).

●

If any other combination of lights flash: Note down the other lights that

are on and contact the Service Centre (see Service).

! For safety the dryer has a maximum programme time of 3 hours. If an

automatic programme has not sensed the required final moisture in this time

the dryer will complete the programme and stop. Check the above points

and run the programme again, if the results are still damp, contact the

Service Centre (see Service).

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance and

Care Troubleshooting Service

GB

11

Service

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

The spare parts have been designed exclusively for

this appliance and not for other uses.

Service

12

GB

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Comparative Programmes

●

Programmes recommended for comparative test to EN61121

! Note: This is not a full list of programme options (see Start and Programmes).

Programme Programme to select Load size

(EN61121)

Dry Cotton 3 Cottons - Hanger Dry 7 kg

Iron Dry Cotton Timed Dry - High Heat (120 minutes) 7 kg

Easy-care textile 1 Synthetics - Cupboard Dry 3 kg

Page is loading ...

Ariston ASL 70 CX User manual

This manual is also suitable for

Ariston ASL 70 CX User manual

in other languages

Related papers

Other documents