VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO
Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
INSTRUCTION MANUAL
BB
BB
rr
rr
aa
aa
dd
dd
NN
NN
aa
aa
ii
ii
ll
ll
ee
ee
rr
rr
//
//
SS
SS
tt
tt
aa
aa
pp
pp
ll
ll
ee
ee
rr
rr
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL 1-800-544-6986
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER
THE PHONE. IF YOU HAVE ASUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS
VITAL TO BLACK & DECKER.
Catalog Number
FS2NC
Catalog Number FSBN125 Shown
635549-00,FS2NC 7/13/05 10:10 AM Page 1
2
WARNING: Read and understand all instructions. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal injury. The
symbols below are used to help you recognize this information.
indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in property
damage.
SAVE THESE INSTRUCTIONS
Read and understand all warnings and operating instructions before
using any tool or equipment. When using tools or equipment, basic safety precautions
should always be followed to reduce the risk of personal injury. Improper operation,
maintenance or modification of tools or equipment could result in serious injury and
property damage. There are certain applications for which tools and equipment are
designed. Black & Decker strongly recommends that this product NOT be modified
and/or used for any application other than for which it was designed.
SAFETY GUIDELINES / DEFINITIONS
• Read and understand tool labels and manual.
Failure to follow warnings could result in DEATH or
SERIOUS INJURY. (Fig. 1)
• Operator and others in work area MUST wear
safety glasses with side shields. These safety
glasses must conform to ANSI Z87.1 requirements
(approved glasses have “Z87” printed or stamped on
them). (Fig. 2)
• Keep fingers AWAY from trigger when not
driving fasteners to avoid accidental firing.
Never carry tool with finger on trigger. In "contact
actuation mode", tool will fire a fastener if tool is
bumped.
• Choice of triggering method is important.
Check manual for triggering options. See “Using
the Tool“ section of this manual.
Fig. 2
Fig. 1
GENERAL SAFETY RULES
635549-00,FS2NC 7/13/05 10:10 AM Page 2
3
• Never point tool at yourself or others in work
area. Serious injury or death may occur if the tool
is activated. (Fig. 3)
• Never use oxygen or other bottled gasses.
Explosion will occur. Never use combustible
gases or any other reactive gas as a power
source for this tool: explosion and serious
personal injury will result. (Fig. 4)
• Wear ear protection to safe-guard against
possible hearing loss. Ear protection equipment
must conform to ANSI S3.19 requirements. (Fig. 5)
• Use clean, dry, regulated, compressed air at 70
to 120 PSI, (4.8 to 8.3 BAR). (Fig. 6)
• Do not connect tool to pressure which
potentially exceeds 200 PSI (13.7 BAR).
• All air line components (hoses, connectors,
filters, regulators, etc.) must be rated for a
maximum working pressure of at least 150 PSI
(10.3 BAR) or 150% of the maximum system
pressure, which ever is greater.
• Connect tool to air supply hose with a coupling
that automatically removes all pressure from the
tool when the coupling is disconnected. (Fig. 7).
• Disconnect tool from air supply hose before
doing tool maintenance, clearing a jammed
fastener, leaving work area, moving tool to another
location, or handing the tool to another person.
(Fig. 7)
• Never use a tool that is leaking air, has missing
or damaged parts, or requires repair. Make sure
all screws and caps are securely tightened.
(Fig. 8).
• Never use tool if safety, trigger or springs are
inoperable, missing or damaged. Do not alter or
remove safety, trigger, or springs. Make daily
inspections for free movement of trigger and
safety mechanism. (Fig. 8)
Fig. 6
Fig. 5
Fig. 3
Fig. 4
Fig. 8
Fig. 7
635549-00,FS2NC 7/13/05 10:10 AM Page 3
4
• Do not use tool without safety warning label. If
label is missing, damaged or unreadable, contact
1-800-544-6986 for a replacement. (Fig. 9)
• Only use parts, fasteners and accessories
approved by Black and Decker.
• Connect tool to air supply before loading
fasteners, to prevent a fastener from being fired
during connection. The tool driving mechanism may
cycle when tool is connected to the air supply.
(Fig. 10)
• Always assume the tool contains fasteners. No
horseplay. Respect the tool as a working
implement. (Fig. 11)
• Operator and bystanders should wear hard hats
to safeguard against possible injuries. (Fig. 12)
• Do not load fasteners with trigger or safety
depressed, to prevent unintentional firing of a
fastener. (Fig. 13
)
• Remove finger from trigger when not driving
fasteners. Never carry tool with finger on trigger. In
“Contact Actuation Mode” tool will fire a fastener if
safety is bumped while trigger is depressed.
(Fig. 14)
Fig. 9
Fig. 11
Fig. 10
Fig. 12
Fig. 13
Fig. 14
635549-00,FS2NC 7/13/05 10:10 AM Page 4
5
• Do not overreach. Keep proper footing and
balance at all times when using or handling the
tool.
• Fire fasteners into work surface only: never
into materials too hard to penetrate. (Fig. 15)
• Grip tool firmly to maintain control while
allowing tool to recoil away from work surface
as fastener is driven. In “Contact Actuation
Mode” if safety element is allowed to re-contact
work surface before trigger is released an
unwanted fastener will be fired.
• Do not drive fasteners on top of other
fasteners, or with the tool at too steep an angle:
the fasteners can ricochet causing personal injury.
(Fig. 15)
• Do not drive fasteners close to the edge of the
workpiece. The workpiece is likely to split
allowing the fastener to fly free or ricochet causing
personal injury. (Fig. 16)
• FOR TOOLS USED IN CONTACT ACTUATION
MODE, Do not use on scaffoldings or ladders
or for tasks in which changing location involves
the use of scaffoldings, stairs, ladders, and the
like. Do not use for specific tasks such as closing
boxes or crates or fitting transportation safety
systems on vehicles and wagons. (Fig. 17)
• Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
• Make sure hose is free of obstructions or
snags. Entangled or snarled hoses can cause
loss of balance or footing.
• Always keep fingers clear of fastener track of
magazine to prevent injury from inadvertent
release of the pusher. (Fig. 18)
• Refer to the Maintenance section for detailed
information on the proper maintenance of the
tool.
• Always operate the tool in a clean, lighted
area. Be sure the work surface is clear of any
debris and be careful not to lose footing when
working in elevated environments such as
rooftops.
• Do not use tool in the presence of flammable
dust, gases or fumes. The tool may produce a
spark that could ignite gases causing a fire.
Driving a fastener into another fastener may also
cause a spark. (Fig. 19)
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
635549-00,FS2NC 7/13/05 10:10 AM Page 5
• Be aware of material thickness when
using the fastener. A protruding fastener
may cause injury.
• Be aware that when the tool is being
utilized at pressures on the high end of its
operating range, fasteners can be driven
completely through thin or very soft work
material. Make sure the pressure in the
compressor is set so that fasteners are set
into the material and not pushed completely
through. (Fig. 20)
• Do not drive fasteners blindly into walls,
floors or other work areas. Fasteners
driven into live electrical wires, plumbing, or
other types of obstructions can result in
injury. (Fig. 21)
• Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
WARNING: Use of this product will expose
you to chemicals known to the State of
California to cause cancer, birth defects and
other reproductive harm. Avoid inhaling
vapors and dust, and wash hands after
using.
6
Fig. 20
Fig. 21
635549-00,FS2NC 7/13/05 10:10 AM Page 6
7
The FSBN125 Nailer is designed to install 18 ga. brad nails of various lengths from
3
/8"
to 1
1
/4" long. Brad nails are loaded into the magazine from the side.
The FSNS100 Stapler is designed to install 18 ga. narrow crown staples of various
lengths from
3
/8" to 1" long. Narrow crown staples are loaded into the magazine from
the top.
POWER SOURCE
This tool is designed to operate on clean, dry, compressed air at regulated pressures
between 70 and 120 PSI (Pounds per Square Inch)
(4.8 to 8.3 BAR)
. The preferred
system would include a filter, a pressure regulator, and an automatic oiler located as close
to the tool as possible, within 15 ft/4.6 m is ideal.
All compressed air contains moisture and other contaminates that are detrimental to
internal components of the tool. An air line filter will remove most of these contaminates
and significantly prolong the life of the tool. If an in-line oiler is not available: place five or
six drops of air tool oil into the tool’s air inlet on a daily basis.
The tool is equipped with a
1
/4" male “quick connector”. The tool must always be
connected to the air supply with a coupling such that all pressure is removed from the tool
when the coupling is disconnected.
PREPARING THE TOOL
Keep tool pointed in a safe direction when loading nails.
Never load fasteners with the contact trip or trigger activated.
1. After reading and understanding this entire manual, connect tool to
air supply. (Fig. 22)
2. Depress latch and slide magazine cover open. (Fig. 23)
3. Insert a strip of approved fasteners. (Fig. 24) Orient fasteners with points down
in the magazine. NOTE: Brad nails are side loaded and staples are top loaded.
4. Push magazine cover closed. (Fig. 25)
5. Observe the low fastener indicator (A) Fig. 26 and reload as needed.
6. Adjust directional exhaust deflector (A) Fig. 27, so that the exhaust air
or debris will be directed away from the operator. Grasp the deflector
and rotate it to the desired position for the current application.
FUNCTIONAL DESCRIPTION
Fig. 22
Fig. 23
Fig. 24 Fig. 25
635549-00,FS2NC 7/13/05 10:10 AM Page 7
8
USING THE TOOL
Complete all steps of PREPARING THE TOOL before using the tool.
This tool is shipped from the factory with a “single sequential actuation” trigger. To
fire, grip the tool firmly to maintain control, position nose of tool onto work
surface, push the tool firmly against work surface to depress safety (S) Fig. 28,
and squeeze trigger to fire a fastener. Allow tool to recoil away from work surface as
fastener is driven. This “single sequential actuation” method provides the most
accurate fastener placement.
Disconnect tool from air supply before performing
maintenance, clearing a jammed fastener, leaving work area, moving tool to
another location, or handing the tool to another person.
Clean and inspect tool daily. Carefully check for proper operation of trigger and
safety mechanism. Do Not use the tool unless both the trigger and the safety
mechanism are functional, or if the tool is leaking air or needs any other repair.
Fig. 26
Fig. 27
A
A
OPERATING INSTRUCTIONS
Fig. 28
S
635549-00,FS2NC 7/13/05 10:10 AM Page 8
9
The depth to which a fastener is driven is controlled by the depth adjustment knob (A)
Fig. 29. The depth of drive is factory adjusted to a nominal setting. Test fire a fastener
and check depth. If a change is desired, rotate the adjustment knob (A) Fig. 29. The
adjustment knob has detents every
1
/4 turn. Rotate the knob (A) Fig. 29 clockwise to
increase the depth of drive, rotate the knob counterclockwise to decrease the depth of
drive. Test fire another fastener and check depth. Repeat as necessary to achieve
desired results. The amount of air pressure required will vary depending on the size of
the fastener and the material being fastened. Experiment with the air pressure setting to
determine the lowest setting that will consistently perform the job at hand. Air pressure
in excess of that required can cause premature wear and/or damage to the tool.
Fig. 29
Fig. 30
A
A
RUBBER NOSE CUSHION
A rubber nose cushion (A) Fig. 30 is provided to reduce marring of the work surface.
The rubber cushion can be removed, and stored inside the magazine (B) Fig. 31 when
it is not required.
Disconnect tool from air supply before removing or re- installing rubber
cushion.
CLEARING A JAMMED FASTENER
Disconnect tool from air supply.
1. Open magazine and remove remaining fasteners. (Fig. 32 and Fig. 33)
Remove fasteners from tool before opening the fastener guide
plate. Fasteners are under pressure and may shoot out of magazine which could
cause injury.
2. Open the quick release latch and the fastener guide plate. (Fig. 34)
3. Remove the jammed fastener. (Fig. 35)
4. Close the fastener guide plate, and the quick release latch.
Fig. 31
B
635549-00,FS2NC 7/13/05 10:10 AM Page 9
10
Fig. 32
Fig. 33
Fig. 34
Fig. 35
MAINTENANCE
CLEAN AND INSPECT DAILY
Disconnect tool from air supply before cleaning and inspection. Correct
all problems before placing the tool back in use.
Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions
to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions.
Such solutions can damage internal parts.
Inspect trigger and safety mechanism to assure system is complete and functional: no
loose or missing parts, no binding or sticking parts.
Keep all screws tight. Loose screws can cause personal injury or damage tool.
If tool is used without an in-line oiler: place five or six drops of air tool oil into the tool’s
air inlet on a daily basis.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service organizations, always using identical
replacement parts.
635549-00,FS2NC 7/13/05 10:10 AM Page 10
11
Disconnect tool from air supply before performing any Service
Procedure.
SYMPTOM PROBLEMS SOLUTIONS
1. Air leak near top of Loose screws. Tighten screws.
tool or in trigger area. Worn or damaged B&D service for overhaul.
o-rings or seals.
2. Tool does nothing or Inadequate air supply. Verify adequate air supply.
operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet.
Worn or damaged B&D service for overhaul.
o-rings or seals.
3. Air leak near bottom Loose screws. Tighten screws.
of tool. Worn or damaged B&D service for overhaul.
o-rings or bumper.
4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of
correct size.
Damaged fasteners. Replace w/undamaged fasteners.
Magazine or nose Tighten screws.
screws loose.
Magazine is dirty. Clean magazine.
Driver is worn or damaged. B&D service for driver maintenance.
5. Other. Contact a Black & Decker
Service Facility.
ACCESSORIES
Recommended accessories for use with your tool are available from your local retailer.
The use of any accessory not recommended for use with this tool could
be hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service
locations throughout North America. All Black & Decker Service Centers are staffed
with trained personnel to provide customers with efficient and reliable power tool
service.
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the Black & Decker location nearest you.
To find your local service location, refer to the yellow page directory under “Tools—
Electric” or call: 1-800-544-6986.
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no
charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns
should be made within the time period of the retailer’s policy for exchanges (usually 30
to 90 days after the sale). Proof of purchase may be required. Please check with the
retailer for their specific return policy regarding returns that are beyond the time set for
exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned
or authorized Service Center for repair or replacement at our option. Proof of purchase
TROUBLESHOOTING
635549-00,FS2NC 7/13/05 10:10 AM Page 11
12
may be required. Black & Decker owned and authorized Service Centers are listed
under “Tools-Electric” in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal
rights and you may have
other rights which vary from state to state and province to province. Should you have
any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
Free Warning Label Replacement: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
635549-00,FS2NC 7/13/05 10:10 AM Page 12
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
36
Cat. # FS2NC (FSBN125 / FSNS100) Form # 635549-00
JULY ‘05 Copyright © 2005 Black & Decker Printed in China
635549-00,FS2NC 7/13/05 10:10 AM Page 36
/