Chief iCSPDA2T02 Installation guide
- Category
- Flat panel wall mounts
- Type
- Installation guide
This manual is also suitable for
Page is loading ...
iCSPDA2 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS
AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the iCSPDA2 does not exceed
40 lbs (18kg).
i
AVISOS Y PRECAUCIONES
IMPORTANTES!
AVISO: Un AVISO llama su atención sobre la posibilidad de
sufrir lesiones de gravedad o incluso mortales si no sigue las
instrucciones.
PRECAUCIÓN: Una nota de PRECAUCIÓN llama su
atención sobre la posibilidad de dañar o destruir
el equipo si no sigue las instrucciones.
AVISO: Si no lee, comprende perfectamente y sigue todas
las instrucciones, podría causar daños graves, daños
personales y materiales o anular la garantía de fábrica. El
instalador es el responsable de asegurarse de que todos los
componentes están correctamente montados e instalados
siguiendo las instrucciones indicadas.
AVISO: Si no se proporciona la resistencia estructural
adecuada para este componente, podrían provocarse graves
daños personales o materiales. El instalador es el
responsable de asegurarse de que la estructura a la que este
componente está sujeta puede soportar cinco veces el peso
combinado de todo el equipo. Refuerce la estructura según
sea necesario antes de instalar el componente.
AVISO: Si se excede el peso máximo, podrían causarse
graves daños personales o materiales. El instalador es
responsable de asegurarse de que el peso combinado de
todos los componentes montados en el iCSPDA2 no excede
40 kg (18 libras).
WICHTIGE WARN- und
VORSICHTSHINWEISE!
WARNUNG: Ein WARNHINWEIS macht auf mögliche
schwere oder tödliche Verletzungen aufmerksam, die bei
Nichtbefolgung der Anweisungen eintreten können.
VORSICHT: Ein VORSICHTSHINWEIS macht auf Schäden
oder mögliche Zerstörung des Geräts aufmerksam, die bei
Nichtbefolgung der Anweisungen eintreten können.
WARNUNG: Falls nicht alle Anweisungen gelesen und gut
verstanden werden, kann dies zu schweren
Körperverletzungen, Schaden an den Geräten führen und die
Werksgarantie nichtig machen! Der Monteur ist dafür
verantwortlich, dass alle Komponenten unter Einhaltung der
mitgelieferten Anweisungen korrekt zusammengebaut und
eingebaut werden.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
iCSPDA2 Installation Instructions
8
LEGEND
Tighten Fastener
Apretar elemento de fijación Stram fastspændingsbeslag
Befestigungsteil festziehen Skruva åt fäste
Apertar fixador Kiristä kiinnike
Serrare il fissaggio Dokrci element mocujcy
Bevestiging vastdraaien
Serrez les fixations Balant Sn
Rögzít meghúzása
Loosen Fastener
Aflojar elemento de fijación Løsgør fastspændingsbeslag
Befestigungsteil lösen Lossa fäste
Desapertar fixador Irrota kiinnike
Allentare il fissaggio
Poluzowa element mocujcy
Bevestiging losdraaien
Desserrez les fixations Balant Gevetin
Rögzít kilazítása
Phillips Screwdriver
Destornillador Phillips Stjerneskuetrækker
Kreuzschlitzschraubendreher Krysskruvmejsel
Chave de fendas Phillips Ristipääruuviavain
Cacciavite a stella rubokrt krzyakowy
Kruiskopschroevendraaier Phillips
Tournevis à pointe cruciforme Phillips Tornavida
Csillagfej csavarhúzó
Open-Ended Wrench
Llave de boca Åben skruenøgle
Gabelschlüssel Fast nyckel
Chave de bocas Kiintoavain
Chiave a punte aperte Klucz paski
Steeksleutel
Clé à fourche Açk Uçlu Anahtar
Villáskulcs
By Hand
A mano Med hånden
Von Hand För hand
Com a mão Käsin
A mano cznie
Met de hand
À la main El le
Kézzel
Hammer
Martillo Hammer
Hammer Hammare
Martelo Vasara
Martello otek
Hamer
Marteau Çekiç
Kalapács
Pencil Mark
Marcar con lápiz Blyantmærke
Stiftmarkierung Pennmarkering
Marcar com lápis Piirretty merkki
Segno a matita Oznaczenie oówkiem
Potloodmerkteken
Marquage au crayon Kalem areti
Ceruzajelölés
Drill Hole
Perforar Borehul
Bohrloch Borra hål
Fazer furo Porausreikä
Praticare un foro Otwór wiercony
Gat boren
Percez un trou Matkap Delii
Lyukfúrás
Adjust
Ajustar Juster
Einstellen Justera
Ajustar Säätää
Regolare Wyregulowa
Afstellen
Ajuster Ayar
Beállítás
Hex-Head Wrench
Llave de cabeza hexagonal Sekskantet skruenøgle
Sechskantschlüssel Insexnyckel
Chave de cabeça sextavada Kuusiokoloavain
Chiave esagonale Klucz z bem szecioktnym
Zeskantsleutel
Clé à tête hexagonale Altgen Kafal (Allen) Anahtar
Hatszögfej kulcs
Socket Wrench
Llave de cubo Hylseskruenøgle
Steckschlüssel Hylsnyckel
Chave de caixa Hylsyavain
Chiave a brugola Klucz nasadowy
Dopsleutel
Clé à douilles Lokma Anahtar
Cskulcs
Measure
Medir Mål
Messen Mät
Medir Mitta
Misurare Przymiar
Meten
Mesurer Ölçüm
Mérték
Installation Instructions iCSPDA2
9
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" (3.2mm)
#2
7mm
A (1)
G (3)
#10 x2-1/2"
(4.8 x 63.5mm)
B (1) C (1)
D (2)
E (2)
F (2)
H (12)
M4 x 12
J (4)
M4 x 20
K (4)
M4 x 30
M (4)
M4
N (4)
3/8"
(9.5mm)
P (4)
3/4"
(19.1mm)
Q (4)
M6 x 12
R (4)
#8 x 3/8"
(4.0 x 9.5mm)
S (1)
3/16"
(4.8mm)
T (1)
3/32"
(2.4mm)
L (2)
M4
iCSPDA2 Installation Instructions
10
DIMENSIONS
Installation Instructions iCSPDA2
11
INSTALL WALL PLATE TO WALL
Wood Stud Installation
WARNING: Failure to provide adequate structural
strength for this component can result in serious
personal injury or damage to equipment! It is the
installer’s responsibility to make sure the structure to
which this component is attached can support five
times the combined weight of all equipment.
Reinforce the structure as required before installing
the component.
1. Level wall plate (B) and mark locations of pilot holes.
2. Drill 1/8" (3.2mm) diameter pilot holes into
wood stud.
3. Install screws (G) through wall plate (B) into
wood stud.
1a
1/8" (3.2mm)
1
1
x3
2
x3
3
G x3
B
iCSPDA2 Installation Instructions
12
INSTALL ARM ASSEMBLY TO WALL PLATE
IMPORTANT! If installing a display with recessed mounting holes, then
proceed to "INSTALL DISPLAY TO ARM ASSEMBLY" before installing arm
assembly to wall plate.
1. Align arm assembly (A) with wall plate (B) and slide into position.
WARNING: Failure to align hex head screw with hole in wall plate (B)
may allow arm assembly (A) to fall, resulting in serious personal injury or
damage to equipment! Hex head screw should fully recede into arm
assembly hole after tightening.
2. Using hex key (T), tighten hex head screw in arm assembly (A) ensuring
that screw engages one of three holes in wall plate (B).
NOTE: Three holes are provided in wall plate (B) to provide height
adjustment.
3. Align cover (C) with grooves in wall plate (B) and slide into position.
4. Align caps (D) with holes in wall plate (B) and slide into position.
2
3
1
2
A
B
3
4
B
C
D x2
2
B
Installation Instructions iCSPDA2
13
INSTALL DISPLAY TO ARM ASSEMBLY
1. If display has a 75 x75mm or 100 x 100mm mounting
pattern, proceed to Step 3A ("Flush Mounting Holes") or
Step 3B ("Recessed Mounting Holes"), as applicable.
Otherwise, continue below.
2. Install screws (H) through brackets (F) and arm assembly
(A) into nuts (M).
3. Proceed to Step 3A ("Flush Mounting Holes") or Step 3B
("Recessed Mounting Holes"), as applicable.
4
(H, Q) x2
3
75 x 75mm, 100 x 100mm
100 x 200mm, 200 x 200mm
1
H x2
Flush Mounting Holes
IMPORTANT! This procedure only applicable when 4mm or
6mm diameter mounting holes are flush with back surface of
display.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the iCSPDA2 does not exceed
40 lbs (18 kg).
CAUTION: Using screws of improper size may damage
your display! Proper screws will easily and completely thread
into display mounting holes.
CAUTION: Inadequate thread engagement in display may
cause display to fall! Back out screws ONLY as necessary to
allow installation to arm assembly.
1. Install two screws (H or Q, as applicable) into the upper
mounting holes on display. Thread screws completely into
display, then back out 3 complete turns.
NOTE: 100 x 100 and 200 x 200 mounting hole patterns
shown; 75 x 75mm and 100 x 200mm patterns similar.
2. Align display so that screws installed in previous step fit into
upper pair of teardrop mounting holes. Lower display firmly
into place.
NOTE: Display will be hanging on upper two screws.
3. Install two remaining screws (H or Q, as applicable) through
lower pair of teardrop mounting holes.
• If installing screws (H) through brackets (F), then install
washers (L) under screw heads (H).
4. Tighten all four screws (H or Q, as applicable). Do not
overtighten!
3A
2
2
H x4
M x4
2
3
H x2
2
3
L x2
A
F x2
A
(H, Q) x2
1
7mm
A
F x2
iCSPDA2 Installation Instructions
14
Recessed Mounting Holes
IMPORTANT! This procedure only applicable when
4mm diameter mounting holes are recessed into back
surface of display.
WARNING: Exceeding the weight capacity can
result in serious personal injury or damage to
equipment! It is the installer’s responsibility to make
sure the combined weight of all components
attached to the iCSPDA2 does not exceed 40 lbs
(18 kg).
1. Carefully place display face down on protective
surface.
2. Place four spacers (N or P, as applicable) over
each mounting hole on back of display. Select
shortest spacer which will provide adequate fill.
All spacers must be same length.
NOTE: 100 x 100 and 200 x 200 mounting hole
patterns shown; 75 x 75mm and 100 x 200mm
patterns similar.
3. Select screw length:
• If using spacers (N), then use screws (J).
• If using spacers (P), then use screws (K).
NOTE: If installing screws (J, K) through brackets (F),
then also use washers (L) for lower pair of
teardrop mounting holes.
4. Orient arm assembly (A) so that teardrop mounting
holes are aligned with holes in spacers (N or P, as
applicable).
CAUTION: Using screws of improper size may
damage your display! Proper screws will easily and
completely thread into display mounting holes.
5. Install screws (J or K, as applicable) through
washers (L, if applicable), teardrop mounting holes,
and spacers (N or P, as applicable), into display.
Tighten all four screws. Do not overtighten!
6. Continue with "INSTALL ARM ASSEMBLY TO
WALL PLATE."
7
3B
75 x 75mm, 100 x 100mm
100 x 200mm, 200 x 200mm
(N, P) x4
2
(J, K) x4
5
(N, P) x4
2
(J, K) x4
5
L x2
F x2
A
A
1
1
Installation Instructions iCSPDA2
15
ADJUSTMENT
WARNING: Excessive loosening or tightening of
adjustment mechanism can result in serious
personal injury or damage to equipment!
1. To adjust pitch/swivel/roll, slightly loosen
adjustment knob (counterclockwise when looking
at back of display), move display to desired angle,
and retighten adjustment knob.
2. To adjust extension, slightly loosen or tighten
adjustment screws using hex key (S). Adjust
screws ONLY as required to achieve desired
tension.
4
2
1
CABLE MANAGEMENT
CAUTION: Ensure that adequate cable slack
exists for movement of display, and that cables will
not be pinched by installation of covers (E) or screws
(R).
1. Carefully insert cables into cavities located in lower
portions of arm assembly (A).
2. Install each cover (E) with two screws (R).
5
1
2
R x4
E x2
A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
iCSPDA2 Installation Instructions
46
:
,
. , ,
, ,
,
,
. ,
.
1. (B)
.
2.
3,2 (1/8") .
3. (G)
(B) .
1a
3,2 (1/8")
1
1
x3
2
x3
3
G x3
B
Installation Instructions iCSPDA2
47
!
,
«
»
, .
1. (A) (B),
.
:
(B),
(A) ,
!
.
2. (T)
(A) ,
(B).
: (B)
.
3. (C) (B)
.
4. (D)
(B) .
2
3
1
2
A
B
3
4
B
C
D x2
2
B
iCSPDA2 Installation Instructions
48
1.
75 x 75 100 x 100 ,
3A («,
») 3B («
»), .
, .
2. (H) (F)
(A) (M).
3. 3A («,
») 3B
(«»),
.
4
(H, Q) x2
3
75 x 75 , 100 x 100
100 x 200 , 200 x 200
1
H x2
,
!
4 6
.
:
! ,
, ,
, iCSPDA2,
18 (40 ).
:
!
.
:
, !
,
.
1. (H Q,
) .
,
3 .
:
100 x 100 200 x 200 ;
75 x 75 100 x 200 .
2. ,
.
.
: .
3. (H Q,
)
.
• (H) (F),
(L) (H).
4. (H Q,
). !
3A
2
2
H x4
M x4
2
3
H x2
2
3
L x2
A
F x2
A
(H, Q) x2
1
7
A
F x2
Installation Instructions iCSPDA2
49
!
4
.
:
! ,
,
, ,
iCSPDA2, 18
(40 ).
1.
.
2.
(N P, )
. ,
.
.
:
100 x 100
200 x 200 ;
75 x 75 100 x 200
.
3. :
• (N),
(J).
• (P),
(K).
: (J, K)
(F),
(L)
.
4. (A) ,
(N, P, ).
:
!
.
5. (J K
) (L, ),
(N P,
) .
. !
6.
«
»
.
7
3B
75 x 75 , 100 x 100
100 x 200 , 200 x 200
(N, P) x4
2
(J, K) x4
5
(N, P) x4
2
(J, K) x4
5
L x2
F x2
A
A
1
1
iCSPDA2 Installation Instructions
50
:
!
1.
(,
),
.
2.
(S).
,
.
4
2
1
: ,
,
,
(E) (R).
1. ,
(A).
2. (E)
(R).
5
1
2
R x4
E x2
A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Installation Instructions iCSPDA2
71
:
!
.
.
1. ()
.
2. 3,2mm (1/8")
.
3. (G)
() .
1a
3,2mm (1/8”)
1
1
x3
2
x3
3
G x3
B
iCSPDA2 Installation Instructions
72
! ,
«
»
.
1. () ()
.
:
(B)
(A),
!
.
2. (),
()
().
: ()
.
3. (C) ()
.
4. (D) ()
.
2
3
1
2
A
B
3
4
B
C
D x2
2
B
Installation Instructions iCSPDA2
73
1. 75 x75mm 100 x 100mm,
3A («»)
3B («»),
. , .
2. (H) (F)
(A) (M).
3. 3A («»)
3B («»),
.
4
(H, Q) x2
3
75 x 75 mm, 100 x 100 mm
100 x 200 mm, 200 x 200 mm
1
H x2
!
4mm 6mm
.
:
!
iCSPDA2
18 kg (40 lbs).
:
!
.
:
!
.
1. (H Q,
) .
, 3
.
:
100 x 100 200 x 200,
75 x 75 mm 100 x 200mm .
2.
.
.
: .
3. (H Q,
)
.
• (H) (F),
(L)
().
4. (H Q,
). !
3A
2
2
H x4
M x4
2
3
H x2
2
3
L x2
A
F x2
A
(H, Q) x2
1
7 mm
A
F x2
iCSPDA2 Installation Instructions
74
!
4mm
.
:
!
iCSPDA2
18 kg (40 lbs).
1.
.
2. (
)
.
.
.
:
100 x 100 200 x 200,
75 x 75mm
100 x 200 mm .
3. :
• (),
(J).
• (P),
(K).
: (J, K)
(F),
(L)
.
4. ()
, ).
:
!
.
5. (J or K,
) (L, ),
,
(N P, ),
. .
!
6. «
».
7
3B
75 x 75 mm, 100 x 100 mm
100 x 200 mm, 200 x 200 mm
(N, P) x4
2
(J, K) x4
5
(N, P) x4
2
(J, K) x4
5
L x2
F x2
A
A
1
1
Installation Instructions iCSPDA2
75
:
!
1. /
,
),
.
2. ,
(S).
.
4
2
1
:
() (R).
1.
().
2. () (R).
5
1
2
R x4
E x2
A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
iCSPDA2 Installation Instructions
86
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
Chief iCSPDA2T02 Installation guide
- Category
- Flat panel wall mounts
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Chief iCSPDA2T02 Guida d'installazione
- français: Chief iCSPDA2T02 Guide d'installation
- español: Chief iCSPDA2T02 Guía de instalación
- Deutsch: Chief iCSPDA2T02 Installationsanleitung
- Nederlands: Chief iCSPDA2T02 Installatie gids
- português: Chief iCSPDA2T02 Guia de instalação
- dansk: Chief iCSPDA2T02 Installationsvejledning
- polski: Chief iCSPDA2T02 Instrukcja instalacji
- Türkçe: Chief iCSPDA2T02 Yükleme Rehberi
- svenska: Chief iCSPDA2T02 Installationsguide
- suomi: Chief iCSPDA2T02 Asennusohje
Related papers
-
Chief ICSPTP2T03 Installation guide
-
Chief ICXPFM2T03 Installation guide
-
Chief iCSPSA2T02 Installation guide
-
-
-
Chief iCSPTM1T02 Specification
-
-
-
-
Chief ICMPFM3B02 Installation guide
Other documents
-
Chief Manufacturing ICMPFM1S User manual
-
PNL-tec EAP450 Datasheet
-
PERLESMITH PSRM1 Installation guide
-
Philips DCB2270/10 Quick Installation Guide
-
Sanus WSWMU User manual
-
North Light Utomhusbelysning Owner's manual
-
-
-
-
Bell'O 7465B User manual
