Hobart Welding Products CHAMP 2060 User manual

Brand: Hobart Welding Products

Model: CHAMP 2060

Category: Welding System

Type: User manual

This manual is also suitable for

Processes

Description

Stick (SMAW) Welding

Engine Driven Welding Generator

OM-499 197 850G

June 2003

Visit our website at

www.HobartWelders.com

CHAMP 2060

Hobart Welders manufactures a full line

of welders and welding related equipment.

For information on other quality Hobart products, contact your local Hobart

distributor to receive the latest full line catalog or individual catalog sheets.

To locate your nearest distributor or service agency call 1-877-Hobart1.

Thank you and congratulations on choosing Hobart. Now you can get the

job done and get it done right. We know you don’t have time to do it any

other way.

This Owner’s Manual is designed to help you get the most out of your

Hobart products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Hobart you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will help

you figure out what the problem is. The parts

list will then help you to decide the exact part

you may need to fix the problem. Warranty and

service information for your particular model

are also provided.

Hobart is registered to the

ISO 9001 Quality System

Standard.

Working as hard as you

do – every power source

from Hobart is backed by

the best warranty in the

business.

From Hobart to You

Hobart offers a Technical

Manual which provides

more detailed service and

parts information for your

unit. To obtain a Technical

Manual, contact your local

distributor. Your distributor

can also supply you with

Welding Process Manuals

such as SMAW, GTAW,

GMAW, and GMAW-P.

The following terms are

used interchangeably

throughout this manual:

TIG = GTAW

Stick = SMAW

MIG = GMAW

The engine exhaust from

this product contains

chemicals known to the

State of California to

cause cancer, birth

defects, or other

reproductive harm.

WARNING

TABLE OF CONTENTS

SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Engine Hazards 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. Additional Symbols For Installation, Operation, And Maintenance 3. . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISATION 5. . . . . . . . . . . . . . . . . . . . .

1-1. Signification des symboles 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Dangers relatifs au soudage à l’arc 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Dangers existant en relation avec le moteur 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. Dangers supplémentaires en relation avec l’installation, le fonctionnement

et la maintenance 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principales normes de sécurité 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. Information sur les champs électromagnétiques 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 – DEFINITIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 – SPECIFICATIONS 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Weld, Power, And Engine Specifications 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. Dimensions, Weights, And Operating Angles 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-3. Fuel Consumption (Kohler-Powered Units) 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4. Fuel Consumption (Honda-Powered Units) 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-5. Duty Cycle 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-6. Generator Power Curves 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-7. Volt-Ampere Curves 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 – INSTALLATION 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Installing Welding Generator 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Grounding Generator To Truck Or Trailer Frame 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-3. Grounding Generator When Supplying Building Systems 15. . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-4. Engine Prestart Checks (Kohler-Powered Units) 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-5. Engine Prestart Checks (Honda-Powered Units) 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-6. Connecting The Battery (Electric-Start Models Only) 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-7. Connecting To Weld Output Terminals 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-8. Selecting Weld Cable Sizes* 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 – OPERATING THE WELDING GENERATOR 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Controls (Kohler-Powered Units) 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Controls (Honda-Powered Units) (See Section 5-3) 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-3. Description Of Controls (Honda-Powered Units) (See Section 5-2) 20. . . . . . . . . . . . . . . . . . . .

SECTION 6 – OPERATING AUXILIARY EQUIPMENT 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1. Generator Power Panel 495 218 (USA) 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Optional Generator Power Panels 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Generator Power Panel Ratings 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Wiring Instructions For Optional 120/240 Volt Twistlock Plug (NEMA L14-30P) 24. . . . . . . . . .

SECTION 7 – MAINTENANCE 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-1. Maintenance Label 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-2. Routine Maintenance 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-3. Overload Protection (Honda-Powered Units) 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-4. Adjusting Engine Speed (Kohler-Powered Units) 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-5. Adjusting Engine Speed (Honda-Powered Units) 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8 – TROUBLESHOOTING 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 9 – ELECTRICAL DIAGRAMS 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 10 – GENERATOR POWER GUIDELINES 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 11 – STICK WELDING (SMAW) GUIDELINES 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 12 – PARTS LIST 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONS AND ACCESSORIES

WARRANTY

WARNING

This product, when used

for welding or cutting,

produces fumes or

gases which contain

chemicals known to the

State of California to

cause birth defects and,

in some cases, cancer.

(California Health &

Safety Code Section

25249.5 et seq.)

WARNING

Battery posts, terminals

and related accessories

contain lead and lead

compounds, chemicals

known to the State of

California to cause

cancer and birth defects

or other reproductive

harm. Wash hands after

handling.

Page is loading ...

OM-499 Page 1

SECTION 1 – SAFETY PRECAUTIONS – READ BEFORE USING

rom _nd_10/02

 Warning: Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

Means Warning! Watch Out! There are possible hazards

with this procedure! The possible hazards are shown in

the adjoining symbols.

 Marks a special safety message.

 Means “Note”; not safety related.

This group of symbols means Warning! Watch Out! possible

ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.

Consult symbols and related instructions below for necessary actions

to avoid the hazards.

1-2. Arc Welding Hazards

 The symbols shown below are used throughout this manual to

call attention to and identify possible hazards. When you see

the symbol, watch out, and follow the related instructions to

avoid the hazard. The safety information given below is only

a summary of the more complete safety information found in

the Safety Standards listed in Section 1-6. Read and follow all

Safety Standards.

 Only qualified persons should install, operate, maintain, and

repair this unit.

 During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the

wire, wire reel, drive roll housing, and all metal parts touching the

welding wire are electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

 Do not touch live electrical parts.

 Wear dry, hole-free insulating gloves and body protection.

 Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

 Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

 Use AC output ONLY if required for the welding process.

 If AC output is required, use remote output control if present

on unit.

 Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

 Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

 Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

 Always verify the supply ground — check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

 When making input connections, attach proper grounding conduc-

tor first – double-check connections.

 Frequently inspect input power cord for damage or bare wiring —

replace cord immediately if damaged — bare wiring can kill.

 Turn off all equipment when not in use.

 Do not use worn, damaged, undersized, or poorly spliced cables.

 Do not drape cables over your body.

 If earth grounding of the workpiece is required, ground it directly

with a separate cable.

 Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

 Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

 Wear a safety harness if working above floor level.

 Keep all panels and covers securely in place.

 Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

 Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

 Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists in inverters after

stopping engine.

 Stop engine on inverter and discharge input capacitors according

to instructions in Maintenance Section before touching any parts.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

 Keep your head out of the fumes. Do not breathe the fumes.

 If inside, ventilate the area and/or use exhaust at the arc to remove

welding fumes and gases.

 If ventilation is poor, use an approved air-supplied respirator.

 Read the Material Safety Data Sheets (MSDSs) and the

manufacturer’s instructions for metals, consumables, coatings,

cleaners, and degreasers.

 Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

 Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

 Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and if necessary, while wearing an

air-supplied respirator. The coatings and any metals containing

these elements can give off toxic fumes if welded.

OM-499 Page 2

BUILDUP OF GAS can injure or kill.

 Shut off shielding gas supply when not in use.

 Always ventilate confined spaces or use

approved air-supplied respirator.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from

the weld.

ARC RAYS can burn eyes and skin.

 Wear a welding helmet fitted with a proper shade of filter to protect

your face and eyes from arc rays and sparks when welding or

watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).

 Wear approved safety glasses with side shields under your

helmet.

 Use protective screens or barriers to protect others from flash and

glare; warn others not to watch the arc.

 Wear protective clothing made from durable, flame-resistant mate-

rial (wool and leather) and foot protection.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

 Protect yourself and others from flying sparks and hot metal.

 Do not weld where flying sparks can strike flammable material.

 Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

 Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

 Watch for fire, and keep a fire extinguisher nearby.

 Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

 Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

 Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock and fire hazards.

 Do not use welder to thaw frozen pipes.

 Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

 Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

 Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

 Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL can injure eyes.

 Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

 Wear approved safety glasses with side

shields even under your welding helmet.

HOT PARTS can cause severe burns.

 Allow cooling period before maintaining.

 Wear protective gloves and clothing when

working on a hot engine.

 Do not touch hot engine parts or just-welded

parts bare-handed.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

 Wear approved ear protection if noise level

is high.

MAGNETIC FIELDS can affect pacemakers.

 Pacemaker wearers keep away.

 Wearers should consult their doctor before

going near arc welding, gouging, or spot

welding operations.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

 Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, slag, open flames, sparks, and arcs.

 Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

 Keep cylinders away from any welding or other electrical circuits.

 Never drape a welding torch over a gas cylinder.

 Never allow a welding electrode to touch any cylinder.

 Never weld on a pressurized cylinder — explosion will result.

 Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

 Turn face away from valve outlet when opening cylinder valve.

 Keep protective cap in place over valve except when cylinder is in

use or connected for use.

 Read and follow instructions on compressed gas cylinders,

associated equipment, and CGA publication P-1 listed in Safety

Standards.

1-3. Engine Hazards

BATTERY EXPLOSION can BLIND.

 Always wear a face shield, rubber gloves, and

protective clothing when working on a battery.

 Stop engine before disconnecting or connect-

ing battery cables or servicing battery.

 Do not allow tools to cause sparks when working on a battery.

 Do not use welder to charge batteries or jump start vehicles.

 Observe correct polarity (+ and –) on batteries.

 Disconnect negative (–) cable first and connect it last.

FUEL can cause fire or explosion.

 Stop engine and let it cool off before checking or

adding fuel.

 Do not add fuel while smoking or if unit is near

any sparks or open flames.

 Do not overfill tank — allow room for fuel to expand.

 Do not spill fuel. If fuel is spilled, clean up before starting engine.

 Dispose of rags in a fireproof container.

 Always keep nozzle in contact with tank when fueling.

OM-499 Page 3

MOVING PARTS can cause injury.

 Keep away from fans, belts, and rotors.

 Keep all doors, panels, covers, and guards

closed and securely in place.

 Stop engine before installing or connecting unit.

 Have only qualified people remove guards or covers for maint-

enance and troubleshooting as necessary.

 To prevent accidental starting during servicing, disconnect

negative (–) battery cable from battery.

 Keep hands, hair, loose clothing, and tools away from moving

parts.

 Reinstall panels or guards and close doors when servicing is

finished and before starting engine.

 Before working on generator, remove spark plugs or injectors to

keep engine from kicking back or starting.

 Block flywheel so that it will not turn while working on generator

components.

STEAM AND HOT COOLANT can burn.

 If possible, check coolant level when engine is

cold to avoid scalding.

 Always check coolant level at overflow tank, if

present on unit, instead of radiator (unless told

otherwise in maintenance section or engine

manual).

 If the engine is warm, checking is needed, and there is no over-

flow tank, follow the next two statements.

 Wear safety glasses and gloves and put a rag over radiator cap.

 Turn cap slightly and let pressure escape slowly before

completely removing cap.

ENGINE EXHAUST GASES can kill.

 Use equipment outside in open, well-ventilated

areas.

 If used in a closed area, vent engine exhaust

outside and away from any building air intakes.

BATTERY ACID can BURN SKIN and EYES.

 Do not tip battery.

 Replace damaged battery.

 Flush eyes and skin immediately with water.

ENGINE HEAT can cause fire.

 Do not locate unit on, over, or near combustible

surfaces or flammables.

 Keep exhaust and exhaust pipes way from

flammables.

EXHAUST SPARKS can cause fire.

 Do not let engine exhaust sparks cause fire.

 Use approved engine exhaust spark arrestor in

required areas — see applicable codes.

1-4. Compressed Air Hazards

BREATHING COMPRESSED AIR can

cause serious injury or death.

 Do not use compressed air for breathing.

 Use only for cutting, gouging, and tools.

COMPRESSED AIR can cause injury

 Wear approved safety goggles.

 Do not direct air stream toward self or others.

TRAPPED AIR PRESSURE AND WHIPPING

HOSES can cause injury.

 Release air pressure from tools and system

before servicing, adding or changing attach-

ments, or opening compressor oil drain or oil

fill cap.

HOT METAL from air arc cutting and

gouging can cause fire or explosion.

 Do not cut or gouge near flammables.

 Watch for fire; keep extinguisher nearby.

HOT PARTS can cause burns and injury.

 Do not touch hot compressor or air system

parts.

 Let system cool down before touching or

servicing.

READ INSTRUCTIONS.

 Read Owner’s Manual before using or servic-

ing unit.

 Stop engine and release air pressure before

servicing.

1-5. Additional Symbols For Installation, Operation, And Maintenance

FALLING UNIT can cause injury.

 Use lifting eye to lift unit only, NOT running

gear, gas cylinders, trailer, or any other

accessories.

 Use equipment of adequate capacity to lift and

support unit.

 If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

OVERHEATING can damage motors.

 Turn off or unplug equipment before starting or

stopping engine.

 Do not let low voltage and frequency caused by

low engine speed damage electric motors.

 Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle

where applicable.

OM-499 Page 4

FLYING SPARKS can cause injury.

 Wear a face shield to protect eyes and face.

 Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

 Sparks can cause fires — keep flammables away.

OVERUSE can cause OVERHEATING.

 Allow cooling period; follow rated duty cycle.

 Reduce current or reduce duty cycle before

starting to weld again.

 Do not block or filter airflow to unit.

STATIC (ESD) can damage PC boards.

 Put on grounded wrist strap BEFORE handling

boards or parts.

 Use proper static-proof bags and boxes to

store, move, or ship PC boards.

TILTING OF TRAILER can cause injury.

 Use tongue jack or blocks to support weight.

 Properly install welding generator onto trailer

according to instructions supplied with trailer.

READ INSTRUCTIONS.

 Use only genuine MILLER/Hobart replacement

parts.

 Perform engine and air compressor (if applica-

ble) maintenance and service according to this

manual and the engine/air compressor (if appli-

cable) manuals.

H.F. RADIATION can cause interference.

 High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

 Have only qualified persons familiar with

electronic equipment perform this installation.

 The user is responsible for having a qualified electrician

promptly correct any interference problem resulting from the

installation.

 If notified by the FCC about interference, stop using the

equipment at once.

 Have the installation regularly checked and maintained.

 Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

 Electromagnetic energy can interfere with

sensitive electronic equipment such as micro-

processors, computers, and computer-driven

equipment such as robots.

 Be sure all equipment in the welding area is

electromagnetically compatible.

 To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

 Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

 Be sure this welding machine is installed and grounded

according to this manual.

 If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

1-6. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

(phone: 305-443-9353, website: www.aws.org).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Mi-

ami, FL 33126 (phone: 305-443-9353, website: www.aws.org).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA

02269-9101 (phone: 617-770-3000, website: www.nfpa.org and www.

sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 1735 Jefferson Davis Highway,

Suite 1004, Arlington, VA 22202-4102 (phone: 703-412-0900, website:

www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 178 Rexdale Bou-

levard, Rexdale, Ontario, Canada M9W 1R3 (phone: 800-463-6727 or

in Toronto 416-747-4044, website: www.csa-international.org).

Practice For Occupational And Educational Eye And Face Protection,

ANSI Standard Z87.1, from American National Standards Institute, 11

West 42nd Street, New York, NY 10036–8002 (phone: 212-642-4900,

website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (phone:

617-770-3000, website: www.nfpa.org and www. sparky.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there

are 10 Regional Offices—phone for Region 5, Chicago, is

312-353-2220, website: www.osha.gov).

1-7. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro-

magnetic fields. There has been and still is some concern about such

fields. However, after examining more than 500 studies spanning 17

years of research, a special blue ribbon committee of the National

Research Council concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that exposure to power-

frequency electric and magnetic fields is a human-health hazard.”

However, studies are still going forth and evidence continues to be

examined. Until the final conclusions of the research are reached, you

may wish to minimize your exposure to electromagnetic fields when

welding or cutting.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from

operator as practical.

5. Connect work clamp to workpiece as close to the weld as

possible.

About Pacemakers:

Pacemaker wearers consult your doctor first. If cleared by your doctor,

then following the above procedures is recommended.

Page is loading ...

OM-499 Page 9

SECTION 2 – DEFINITIONS

2-1. Symbol Definitions

Engine Choke

Read Operator’s

Manual A

Amperes

Volts

Engine Oil Fuel Battery (Engine) Engine

Positive Negative

Alternating Current

(AC)

Output

Hours

Seconds Time

Protective Earth

(Ground)

Circuit Breaker Temperature

SECTION 3 – SPECIFICATIONS

This unit uses either a Kohler or a Honda engine. Differences between models are

noted throughout this manual.

NOTE

3-1. Weld, Power, And Engine Specifications

Welding

Mode

Weld Output

Range

Rated

Welding

Output

Maximum

Open Circuit

Voltage

Generator Power

Rating

Fuel Capacity Engine

CC/DC

40 – 180 A

(60 Hz)

40 – 160 A

(50 Hz)

180 A, 25 V,

30% Duty

Cycle

130 A, 25 V,

60% Duty

Cycle

100 A, 25 V,

100% Duty

Cycle

(60 Hz)

(50 Hz)

Single-Phase,

6 kVA/kW (Peak)

5.5 kVA/kW

(Continuous)

50/25 A,

110/220 V AC, 50 Hz

120/240 V AC, 60 Hz

Kohler:

1.8 gal (6.9 L) Tank

Honda:

1.7 gal (6.4 L) Tank

Kohler CS12STG

Air-Cooled,

One-Cylinder,

Four-Cycle,

12 HP (360 CC),

Gasoline Engine

Honda GX390

Air-Cooled,

One-Cylinder,

Four-Cycle,

13 HP (390 CC),

Gasoline Engine

OM-499 Page 10

3-2. Dimensions, Weights, And Operating Angles

Dimensions

Height 20-3/4 in (527 mm)

Width 22-3/4 in (577 mm)

Depth 31-1/4 in (793 mm)

 Do not exceed tilt angles or engine could

be damaged or unit could tip.

A 31-1/4 in (793 mm)

be damaged or unit could tip.

 Do not move or operate unit where it

B 10-1/2 in (268 mm)

 Do not move or operate unit where it

could tip.

C 13-45/64 in (348 mm)

D 22-3/4 in (577 mm)

E 1-3/4 in (44 mm)

F 19-1/2 in (495 mm)

G 13/32 in (10 mm) Dia.

Weight

15°

Kohler: 265 lb (120 kg)

Holes

15°

Honda Electric-Start Model:

278 lb (126 kg)

Honda Recoil-Start Model:

253 lb (114 kg)

802 096

Holes

Engine End

802 524-A

3-3. Fuel Consumption (Kohler-Powered Units)

198 575

50 HZ–AUX

50 HZ–WELD

HIGH IDLE

60 HZ–WELD

60 HZ–AUX

 Fuel consumption at low idle

(2000 rpm): 0.2 U.S. gal/hr.

OM-499 Page 11

3-4. Fuel Consumption (Honda-Powered Units)

802 122

Continuous Welding

3-5. Duty Cycle

802 093

Duty cycle is the percentage of 10

minutes that unit can weld at rated

load without overheating.

 Exceeding duty cycle can

damage unit and void

warranty.

100% Duty Cycle at 100 Amperes CC/DC

OM-499 Page 12

3-6. Generator Power Curves

198 570

The generator power curves show

the ac power available in amperes

at the receptacles.

A. 60 Hz Model

B. 50 Hz Model

100

125

150

175

200

225

250

0 5 10 15 20 25 30 35

LOAD AMPS

LOAD VOLTS

100

125

150

175

200

225

250

0 5 10 15 20 25 30 35

LOAD AMPS

LOAD VOLTS

OM-499 Page 13

3-7. Volt-Ampere Curves

198 570

The volt-ampere curve shows the

minimum and maximum voltage

and amperage output capabilities o

the welding generator. Curves of al

other settings fall between the

curves shown.

A. 60 Hz Model

B. 50 Hz Model

0 25 50 75 100 125 150 175 200 225 250

LOAD AMPS

LOAD VOLTS

MIN

MID

MAX

0 25 50 75 100 125 150 175 200 225 250

LOAD AMPS

LOAD VOLTS

MIN

MID

MAX

OM-499 Page 14

SECTION 4 – INSTALLATION

4-1. Installing Welding Generator

install1 10/00*– 802 524-A / Ref. 151 556 / 158 936-A / S-0854

18 in

(460 mm)

18 in

(460 mm)

18 in

(460 mm)

18 in

(460 mm)

18 in

(460 mm)

Movement Airflow Clearance

Location

 Always securely fasten welding

generator onto transport vehicle

or trailer and comply with all DOT

and other applicable codes.

4-2. Grounding Generator To Truck Or Trailer Frame

install1 10/00* – Ref. 151 556 / S-0854

 Always ground generator

frame to vehicle frame to pre-

vent electric shock and static

electricity hazards.

1 Generator Base

2 Metal Vehicle Frame

3 Equipment Grounding

Terminal

4 Grounding Cable

Use #10 AWG or larger insulated

copper wire.

 If unit does not have GFCI re-

ceptacles, use GFCI-

protected extension cord.

Electrically bond generator frame to

vehicle frame by metal-to-metal con-

tact.

GND/PE

OM-499 Page 15

4-3. Grounding Generator When Supplying Building Systems

GND/PE

1 2

Use ground device as

stated in electrical codes.

800 576-B

1 Equipment Grounding

Terminal

2 Grounding Cable

Use #10 AWG or larger insulated

copper wire.

3 Ground Device

 Ground generator to sys-

tem earth ground if supply-

ing power to a premises

(home, shop, farm) wiring

system.

-4. Engine Prestart Checks (Kohler-Powered Units)

802 511-A

Full

Gasoline

1/2 in

(13 mm)

 Follow run-in procedure in engine

manual.

Check all fluids daily. Engine must be

cold and on a level surface. Unit is

shipped with 10W30 engine oil.

Engine stops if oil level gets too low.

 This unit has a low oil level shut-

down switch. However, some con-

ditions may cause engine damage

before the engine shuts down.

Check oil level often and do not use

the oil level shutdown system to

monitor oil level.

1 Fuel Valve

Open valve by turning lever to vertical

position.

 Close fuel valve before moving unit

or carburetor may flood and make

starting difficult.

Fuel

Add fresh fuel before starting engine the

first time (see maintenance label for

specifications). Fill fuel tank up to 1/2 in.

(13 mm) from top to allow room for ex-

pansion. Check fuel level on a cold en-

gine before use each day.

Oil

After fueling, check oil with unit on level

surface. If oil is not up to full mark on dip-

stick, add oil (see maintenance label).

 To improve cold weather starting:

Keep battery in good condition.

Store battery in warm area.

Use correct grade oil for cold

weather.

Open

Closed

OM-499 Page 16

-5. Engine Prestart Checks (Honda-Powered Units)

802 094-A

Full

Gasoline

1/2 in

(13 mm)

Check all fluids daily. Engine must

be cold and on a level surface. Unit

is shipped with 10W30 engine oil.

Engine stops if oil level gets too low.

 Follow run-in procedure in en-

gine manual.

1 Fuel Valve

Open valve.

 Close fuel valve before moving

unit or carburetor may flood

and make starting difficult.

Fuel

Add fresh fuel before starting

engine the first time (see mainte-

nance label for specifications). Fill

fuel tank up to 1/2 in. (13 mm) from

top to allow room for expansion.

Check fuel level on a cold engine

before use each day.

Oil

After fueling, check oil with unit on

level surface. If oil is not up to full

mark on dipstick, add oil (see main-

tenance label).

 To improve cold weather

starting:

Keep battery in good condition.

Store battery in warm area.

Use correct grade oil for cold

weather.

Open

4-6. Connecting The Battery (Electric-Start Models Only)

802 524 / Ref. S-0756-D

3/8, 1/2 in

Tools Needed:

–

 Connect negative (–)

cable last.

 Turn Engine Switch to Of

(electric-start models only).

OM-499 Page 17

4-7. Connecting To Weld Output Terminals

196 914 / 495 178

1 Positive (+) Weld Output

Terminal

2 Negative (–) Weld Output

Terminal

For Direct Current Electrode Posi

tive (DCEP), connect work cable to

Negative (–) terminal and electrode

holder to Positive (+) terminal.

For Direct Current Electrode nega

tive (DCEN), reverse cable con

nections.

Tools Needed:

3/4 in

4-8. Selecting Weld Cable Sizes*

Weld Cable Size** and Total Cable (Copper) Length in Weld Circuit

Not Exceeding***

100 ft (30 m) or Less

150 ft

(45 m)

200 ft

(60 m)

250 ft

(70 m)

300 ft

(90 m)

350 ft

(105 m)

400 ft

(120 m)

Weld Output

Terminals

 Stop engine before

connecting to weld out-

put terminals.

 Do not use worn, dam-

aged, undersized, or

poorly spliced cables.

Welding

Amperes

10 – 60%

Duty

Cycle

60 – 100%

Duty

Cycle

10 – 100% Duty Cycle

100 4 (20) 4 (20) 4 (20) 3 (30) 2 (35) 1 (50) 1/0 (60) 1/0 (60)

150 3 (30) 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 3/0 (95)

200 3 (30) 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120) 4/0 (120)

250 2 (35) 1 (50) 1/0 (60) 2/0 (70) 3/0 (95) 4/0 (120)

2 ea. 2/0

(2x70)

2 ea. 2/0

(2x70)

* This chart is a general guideline and may not suit all applications. If cable overheating occurs (normally you can smell it), use next size larger

cable.

**Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere.

( ) = mm

for metric use S-0007-E

***For distances longer than those shown in this guide, call a factory applications representative at 920-735-4505.

OM-499 Page 18

SECTION 5 – OPERATING THE WELDING GENERATOR

5-1. Controls (Kohler-Powered Units)

802 511-A / 802 0511 / 495 178

60 Hz

 Weld and generator power output stops if

generator overheats or engine speed is

too low.

1 Engine Switch

Use switch to open ignition circuit, and to stop

engine.

2 Throttle Control Lever

Use lever to select engine speed. Use 50 Hz

or 60 Hz position for 50 or 60 Hz generator

power. Use 60 Hz position for maximum weld

output.

3 Choke Control Lever

Use lever to change engine air/fuel mix. Move

lever to right if starting a cold engine. Move le-

ver to left if starting a warm engine.

To Start (Electric): open fuel valve (see Sec-

tion 4-4), move throttle lever to Idle, set choke,

and turn engine switch to Start position. Open

choke as engine warms. If engine does not

crank, use recoil starting procedure following

to start engine.

 If engine does not start, let engine

come to a complete stop before at-

tempting restart.

4 Starter Handle

To Start (Recoil): open fuel valve (see Sec-

tion 4-4), move throttle lever to Idle, set choke,

and pull starter handle. Open choke as engine

warms.

To Stop: turn engine switch to Off.

 Always close fuel valve after stopping

unit. Moving unit with fuel valve open may

cause carburetor flooding and make

starting difficult.

5 Engine Hour Meter

6 Welding Range Label

Use label to determine correct weld amper-

age based on electrode size, type, and mate-

rial thickness.

7 Current Control

Use control to select weld amperage. Control

may be adjusted while welding.

To Set Current Control: Use label to deter-

mine correct size electrode for material thick-

ness. Select electrode type and set current

control to corresponding amperage range.

Adjust control to obtain desired weld

performance.

EXAMPLE:

Material Thickness: 1/8 to 1/4 in

Electrode Diameter: 1/8

Electrode Type: E-6013

Current Control Setting: 90 – 120 A

50 Hz

OM-499 Page 19

5-2. Controls (Honda-Powered Units) (See Section 5-3)

802 094-A / 802 095 / 495 187

Recoil-Start

Electric-Start

60 Hz

50 Hz

OM-499 Page 20

5-3. Description Of Controls (Honda-Powered Units) (See Section 5-2)

 Weld and generator power output stops if

generator overheats or engine speed is

too low.

1 Engine Switch

On models with recoil-start, use switch to

open ignition circuit, and to stop engine.

On models with electric-start, use switch to

open ignition circuit, and to start and stop en-

gine.

2 Throttle Control Lever

Use lever to select engine speed. Use 50 Hz

or 60 Hz position for generator power. Use 60

Hz position for maximum weld output.

3 Choke Control Lever

Use lever to change engine air/fuel mix. Move

lever to left if starting a cold engine. Move le-

ver to right if starting a warm engine.

4 Starter Handle (Recoil-Start Models

Only)

To Start (Recoil): open fuel valve, turn engine

switch to On, move throttle lever to Idle, set

choke, and pull starter handle. Open choke as

engine warms.

To Start (Electric): open fuel valve, move

throttle lever to Idle, set choke, and turn en-

gine switch to Start position. Open choke as

engine warms.

 If engine does not start, let engine

come to a complete stop before at-

tempting restart.

To Stop: turn engine switch to Off.

 Always close fuel valve after stopping

unit. Moving unit with fuel valve open may

cause carburetor flooding and make

starting difficult.

5 Engine Hour Meter

6 Welding Range Label

Use label to determine correct weld amper-

age based on electrode size, type, and mate-

rial thickness.

7 Current Control

Use control to select weld amperage. Control

may be adjusted while welding.

To Set Current Control: Use label to deter-

mine correct size electrode for material thick-

ness. Select electrode type and set current

control to corresponding amperage range on

nameplate. Adjust control within selected

range to obtain desired weld performance.

EXAMPLE:

Material Thickness: 1/8 to 1/4 in

Electrode Diameter: 1/8

Electrode Type: E-6013

Current Control Setting: 90 – 120 A

Notes

OM-499 Page 21

SECTION 6 – OPERATING AUXILIARY EQUIPMENT

The welding generator provides power while welding and with the Current control

in any position. However, under these conditions equipment connected to the

welding generator may be subject to larger than normal voltage fluctuations. It is

recommended that only lamps be powered under these conditions.

NOTE

6-1. Generator Power Panel 495 218 (USA)

495 218

1234 5

 If unit does not have GFCI recep-

tacles, use GFCI-protected exten-

sion cord.

 Power is still present at the 240 volt

receptacle when only one circuit

breaker trips.

Unplug power cord before attempt-

ing to service accessories or tools.

 Generator power decreases as weld

current increases.

Set Amperage control at max. for full

generator power.

 Place throttle lever in Run position (far

right) for generator power.

1 120 V AC Twistlock Receptacle RC1

RC1 supplies 60 Hz single-phase power at

weld/power speed. Maximum output is 3.5

kVA/kW.

2 120 V 20 A AC Duplex Receptacle

RC2

3 120 V 20 A AC Duplex Receptacle

RC3

RC2 and RC3 supply 60 Hz single-phase

power at weld/power speed. Maximum

output from RC2 or RC3 is 2.4 kVA/kW.

 Each receptacle of the duplex can pro-

vide 15A/1800W.

 Do not parallel the two 120V duplex

receptacles.

4 Circuit Breaker CB1

CB1 protects RC1 from overload. If CB1

opens, RC1 does not work.

5 Circuit Breakers CB2 And CB3

CB2 protects RC2 and CB3 protects RC3

from overload. If a circuit breaker opens,

the receptacle does not work.

 Press button to reset circuit breaker. If

breaker continues to open, contact

Factory Authorized Service Agent.

Combined output of all receptacles limited

to 6 kVA/kW rating of the generator (See

Section 10 – Generator Power Guide-

lines).

EXAMPLE: If 10 A is drawn from each 120

volt duplex receptacle, only 9 A is available

from the 120 V twistlock receptacle.

2 x (120 V x 10 A) + (240 V x 9 A) = 3.5 kVA/

KW.

Page is loading ...

Hobart Welding Products CHAMP 2060 User manual

Brand: Hobart Welding Products

Model: CHAMP 2060

Category: Welding System

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Hobart Welding Products CHAMP 2060 Manuel utilisateur

Hobart Welding Products CHAMP 2060 User manual

This manual is also suitable for

Hobart Welding Products CHAMP 2060 User manual

in other languages

Related papers

Other documents