IMG Stage Line PARL-12DMX User manual

DMX-LED-SCHEINWERFER

DMX LED SPOTLIGHT

PROJECTEUR DMX À LEDS

PROIETTORE DMX A LED

PARL-12DMX Bestellnummer 38.5510

BEDIENUNGSANLEITUNG • INSTRUCTION MANUAL

MODE D’EMPLOI • ISTRUZIONI PER L’USO • MANUAL DE INSTRUCCIONES

INSTRUKCJA OBSŁUGI • VEILIGHEIDSVOORSCHRIFTEN

SIKKERHEDSOPLYSNINGER • SÄKERHETSFÖRESKRIFTER • TURVALLISUUDESTA

Page is loading ...

3

Bevor Sie einschalten …

Wir wünschen Ihnen viel Spaß mit Ihrem neuen

Gerät von „img Stage Line“. Bitte lesen Sie diese

Bedienungsanleitung vor dem Betrieb gründlich

durch. Nur so lernen Sie alle Funktionsmöglich-

keiten kennen, vermeiden Fehlbedienungen und

schützen sich und Ihr Gerät vor eventuellen Schä-

den durch unsachgemäßen Gebrauch. Heben

Sie die Anleitung für ein späteres Nachlesen auf.

Der deutsche Text beginnt auf der Seite 4.

Before switching on …

We wish you much pleasure with your new “img

Stage Line” unit. Please read these operating

instructions carefully prior to operating the unit.

Thus, you will get to know all functions of the unit,

operating errors will be prevented, and yourself

and the unit will be protected against any damage

caused by improper use. Please keep the oper -

ating instructions for later use.

The English text starts on page 10.

Avant toute installation …

Nous vous souhaitons beaucoup de plaisir à uti-

liser cet appareil “img Stage Line”. Lisez ce mode

dʼemploi entièrement avant toute utilisation. Uni-

quement ainsi, vous pourrez apprendre lʼensem-

ble des possibilités de fonctionnement de lʼappa-

reil, éviter toute manipulation erronée et vous

protéger, ainsi que lʼappareil, de dommages

éventuels en gendrés par une utilisation inadap-

tée. Conservez la notice pour pouvoir vous y

reporter ultérieurement.

La version française se trouve page 16.

Prima di accendere …

Vi auguriamo buon divertimento con il vostro

nuovo apparecchio di “img Stage Line”. Leggete

at tentamente le istruzioni prima di mettere in fun-

zione lʼapparecchio. Solo così potete conoscere

tutte le funzionalità, evitare comandi sbagliati e

proteggere voi stessi e lʼapparecchio da even-

tuali danni in seguito ad un uso improprio. Con-

servate le istruzioni per poterle consultare anche

in futuro.

Il testo italiano inizia a pagina 22.

D

A

CH

GB

Innan du slår på enheten …

Vi önskar dig mycket glädje med din nya “img

Stage Line” produkt. Läs igenom säkerhetsföre -

skrif terna innan en heten tas i bruk för att undvika

skador till följd av felaktig hantering. Behåll

instruktionerna för framtida bruk.

Säkerhetsföreskrifterna återfinns på sidan 41.

Ennen kytkemistä …

Toivomme Sinulle paljon miellyttäviä hetkiä uuden

“img Stage Line” laitteen kanssa. Ennen laitteen

käyttöä pyydämme Sinua huolellisesti tutustu-

maan turvallisuusohjeisiin. Näin vältyt vahingoilta,

joita virheellinen laitteen käyttö saattaa aiheuttaa.

Ole hyvä ja säilytä käyttöohjeet myöhempää tar-

vetta varten.

Turvallisuusohjeet löytyvät sivulta 41.

F

B

CH

I

S FIN

Antes de la utilización …

Le deseamos una buena utilización para su nue -

vo aparato “img Stage Line”. Por favor, lea estas

in s trucciones de uso atentamente antes de ha cer

funcionar el aparato. De esta manera conocerá

todas las funciones de la unidad, se pre vendrán

errores de operación, usted y el apa rato estarán

protegidos en contra de todo daño cau sado por

un uso inadecuado. Por favor, guarde las instruc-

ciones para una futura utilización.

El texto en español empieza en la página 28.

Voor u inschakelt …

Wij wensen u veel plezier met uw nieuwe appa-

raat van “img Stage Line”. Lees de veiligheids-

voorschriften grondig door, alvorens het apparaat

in gebruik te nemen. Zo behoedt u zichzelf en het

apparaat voor eventuele schade door ondeskun-

dig gebruik. Bewaar de handleiding voor latere

raadpleging.

De veiligheidsvoorschriften vindt u op pagina 40.

Przed uruchomieniem …

Zyczymy zadowolenia z nowego produktu “img

Stage Line”. Dzięki tej instrukcji obsługi będą

państwo w stanie poznać wszystkie funkcje tego

urządzenia. Stosując się do instrukcji unikną

państwo błędów i ewentualnego uszkodzenia

urządzenia na skutek nieprawidłowego użytko-

wania. Prosimy zachować instrukcję.

Tekst polski zaczyna się na stronie 34.

Før du tænder …

Tillykke med dit nye “img Stage Line” produkt.

Læs sikkerhedsanvisningerne nøje før ibrugtag-

ning, for at beskytte Dem og enheden mod ska-

der, der skyldes forkert brug. Gem manualen til

senere brug.

Sikkerhedsanvisningerne findes på side 40.

E PL

DK

NL

B

wwwwww..iimmggssttaaggeelliinnee..ccoomm

Page is loading ...

All operating elements and connections de -

scribed can be found on page 2.

1 Operating Elements

and Connections

1.1 Rear side

1 Mounting brackets

2 Control SENSITIVITY for the sensitivity of

response in case of music control via the micro-

phone (3)

3 Microphone for music control

4 Mains jack for connection to a socket (230 V~/

50 Hz) via the supplied mains cable or for con-

nection to the jack POWER LINK OUTPUT (10)

of another PARL-12DMX

5 Display

6 Operational buttons

Buttons UP and DOWN for selection of a control

programme or a colour and for adjusting the

DMX start address

Button ENT (= Enter) to confirm a selection and

to memorize an adjustment

Button FUNC (= Function) to select the operat-

ing mode

DMX reception, control by other spot-

lights (slave mode) or remote control, adjust-

ment of the DMX start address

programmes running automatically

programmes controlled by music

colour spotlight with selectable colour

7 Locking screws for the mounting brackets (1)

8 Support for the mains fuse

Only replace a blown fuse by one of the same

type

9 Lug for fixing a safety rope

10 Connection POWER LINK OUTPUT for power

supply of another unit

11 Connection jack REMOTE for the foot-operated

remote control FS-2PARL (at option)

12 DMX signal input (3-pole XLR) for connection of

a light controller;

pin 1 = ground, 2 = DMX

-

, 3 = DMX+

13 DMX signal output (3-pole XLR) for connection

to the DMX input of another DMX light effect

unit;

pin 1 = ground, 2 = DMX

-

, 3 = DMX+

1.2 Remote control FS-2PARL

The remote control is available as an accessory

and is not supplied together with the light effect

unit.

14 Display

15 Button COLOUR to select a light colour

16 Button MODE to select a colour changing pro-

gramme or a stroboscope programme

17 Button BLACKOUT to switch the light on and off

18 Jack RJ45 for connection to the jack REMOTE

(11) via the supplied cable

19 Microphone for music control

20 Control SENSITIVITY for the sensitivity of

response in case of music control via the micro-

phone (19)

Note: For control via the remote control no DMX signal

must be present at the input DMX INPUT (12).

2 Safety Notes

The units (spotlight PARL-12DMX and remote con-

trol FS-2PARL) correspond to all relevant directives

of the EU and are therefore marked with .

Please observe the following items in any case:

G

The units are suitable for indoor use only. Protect

them against dripping water and splash water,

high air humidity, and heat (admissible ambient

temperature range 0 – 40 °C).

G

Do not place any vessels filled with liquid, e. g.

drinking glasses, on the units.

G

Do not set the spotlight into operation or immedi-

ately disconnect the mains plug from the mains

socket

1. if the unit or the mains cable is visibly dam-

aged,

2. if a defect might have occurred after the unit

was dropped or suffered a similar accident,

3. if malfunctions occur.

In any case the unit must be repaired by skilled

personnel.

G

Never pull the mains cable for disconnecting the

mains plug from the mains socket, always seize

the plug.

G

No guarantee claims for the units and no liability

for any resulting personal damage or material

WARNING The spotlight uses hazardous mains

voltage. Leave servicing to skilled

personnel only and do not insert any-

thing into the air vents; inexpert han-

dling may result in electric shock.

10

GB

damage will be accepted if the units are used for

other purposes than originally intended, if they

are not safely mounted, not correctly connected

or operated, or if they are not repaired in an

expert way.

G

Important for U. K. Customers!

The wires in this mains lead are coloured in

accordance with the following code:

green/yellow = earth

blue = neutral

brown = live

As the colours of the wires in the mains lead of

this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows:

1. The wire which is coloured green and yellow

must be connected to the terminal in the plug

which is marked with the letter E or by the earth

symbol , or coloured green or green and yel-

low.

2. The wire which is coloured blue must be con-

nected to the terminal which is marked with the

letter N or coloured black.

3. The wire which is coloured brown must be con-

nected to the terminal which is marked with the

letter L or coloured red.

Warning – This appliance must be earthed.

3 Applications

This flat LED spotlight serves for illumination e. g.

on stage, in discotheques and festival rooms. As a

light source, 153 extra bright LEDs with a diameter

of 10 mm are used which have a low power con-

sumption, a low heat development and a long life.

The LEDs allow to radiate coloured light in the

three primary colours (red, green and blue) and

light which can be mixed from the primary colours

by addition. Besides, colour crossfadings and stro-

boscopic effects are possible.

The spotlight can be operated via the remote

control FS-2PARL available as an accessory or via

a DMX light controller (4 DMX control channels).

However, it can also be operated without a con-

troller, either on its own or interconnected with sev-

eral PARL-12DMX units in the master/slave mode.

The integrated microphone provides effects in sync

with the music.

4 Setting into Operation

4.1 Mounting

G

Always place the unit so that a sufficient air cir-

culation is ensured during operation. The air

vents at the housing must not be covered in any

case.

G

The distance to the illuminated object should be

50 cm as a minimum.

1. Fix the spotlight via the mounting brackets (1),

e. g. with a stable mounting screw or a support

for lighting units (C hook) to a cross bar.

To align the spotlight, release the two locking

screws (7) at the mounting brackets. Adjust the

desired inclination of the spotlight and retighten

the screws.

2. As an alternative, the spotlight can also be set

up as desired. For this purpose spread the

mounting brackets below the spotlight so that

they serve as a support. Then tighten the locking

screws.

4.2 Power supply

Connect the supplied mains cable to the mains jack

(4) first and then to a socket (230 V~/ 50 Hz). Then

the unit is ready for operation and can be operated

via a DMX light controller (



chapter 5.4) or it runs

independently through the control programme

adjusted (



chapter 5.1). To switch off, disconnect

the mains plug from the socket.

If several PARL-12DMX units are used, the jack

POWER LINK OUTPUT (10) of the first unit can be

WARNING Never look directly into the light

source for a longer time; this may

cause eye damage.

Please note that fast changes in

lighting, e. g. flashing light, may trig-

ger epileptic seizures with photosen-

sitive persons or persons with epi -

lepsy!

WARNING The spotlight must be mounted in a

safe and expert way. If it is installed

at a place where people may walk or

sit under it, it must additionally be

secured, e. g. by a safety rope. Lead

the safety rope through the lug (9)

and fix it so that the maximum falling

distance of the unit would not exceed

20 cm.

If the units are to be put out of operation

definitively, take them to a local recycling

plant for a disposal which is not harmful to

the environment.

11

GB

connected via a mains cable with an IEC plug and

an IEC inline jack (e. g. AAC-170/SW from the

product range of MONACOR) to the mains jack (4)

of the second unit. The second unit can again be

connected to the third unit etc., until all units are

connected in a chain. Thus, a maximum of 50 units

may be interconnected. Then the 51st unit must

have a mains connection of its own.

Caution: The unit must

not

be connected to the

mains voltage via a dimmer!

For a more convenient operation it is recommended

to connect the unit to a socket which can be

switched on and off via a light switch.

5 Operation

5.1 Operation without DMX control unit

5.1.1 Music-controlled programmes

1) Press the button FUNC (6).

2) Select the function with the button UP or

DOWN and confirm with the button ENT.

3) Select the desired control programme with the

button UP or DOWN and confirm with the button

ENT. The display (5) shows the programme:

The lighting colour is changed by music

control (mixed colours only).

Music-controlled stroboscope with colour

change (mixed colours only)

Music-controlled stroboscope with colour

change (primary colours and mixed

colours)

The lighting colour is changed by music

control (primary colours and mixed

colours).

If the music is played with a clear rhythm in the

bass range at sufficient volume, the selected pro-

gramme is controlled via the microphone (3). Adjust

the control SENSITIVITY (2) for the microphone

sensitivity so that the dynamic power of the music

is reproduced by the unit in an optimum way. For

programmes and , the colours are auto-

matically changed during music breaks after a few

seconds.

5.1.2 Programmes running automatically

1) Press the button FUNC (6).

2) Select the function with the button UP or

DOWN and confirm with the button ENT.

3) Select the desired control programme with the

button UP or DOWN and confirm with button

ENT. The display (5) shows the programme:

The lighting colour is changed automat-

ically after approx. 5 s in each case.

Automatic colour change with slow fad-

ing in and out

Automatic colour change with slow fad-

ing in and then immediate colour change

Automatic crossfading of different

colours

same as

Automatic colour change with slow fad-

ing out in each case.

5.1.3 Colour spotlight with selectable colour

1) Press the button FUNC (6).

2) Select the function with the button UP or

DOWN and confirm with the button ENT.

3) Select the desired colour with the button UP or

DOWN and confirm with the button ENT. The

display (5) shows the number of the colour:

white

red

green

blue

purple

cyan

yellow

pink

orange

light green

5.2 Interconnection of several

PARL-12DMX units

Several PARL-12DMX units may be interconnected

(master-slave operation). Then all slave units can

be controlled in sync with the master unit.

1) Connect the DMX OUTPUT (13) of the master

unit via a 3-pole XLR cable (e. g. series MEC-…

or MECN-… from the product range of MONA-

COR) to the DMX INPUT (12) of the first slave

unit.

2) Connect the DMX OUTPUT of the first slave unit

to the DMX INPUT of the second slave unit, etc.

until all units have been connected in a chain.

3) No DMX signal must be present at the DMX

INPUT of the master unit. Adjust the slave units

to the DMX address 001 (



chapter 5.4.2).

12

GB

Once the control signals from the master unit are

present at the slave units, they are controlled by the

master unit and the dot behind the first position on

the display (5) flashes. If a slave unit does not

receive any control signals, the indication

appears on its display.

5.3 Remote control via FS-2PARL

Via the foot-operated remote control FS-2PARL

available as an accessory, up to 50 spotlights can

be controlled together.

1) Connect the jack RJ45 (18) on the rear side of

the remote control FS-2PARL via the supplied

cable to the jack REMOTE (11).

2) Adjust the spotlight to the DMX address 001

(



chapter 5.4.2).

3) No DMX signal must be present at the input

DMX INPUT (12).

4) Via the output DMX OUTPUT (13) further PARL-

12DMX units may be connected (



chapter

5.2) to control them together with the main unit

via the remote control. For the identical control

of the slave units in principle, adjust their DMX

address to 001 as well. For partly opposite con-

trol and running light effects for the music-con-

trolled programmes and (



chapter

5.3.2) set the slave units to the DMX addresses

005, 009, 013, 001, 005, 009, 013, etc.

5.3.1 Switching the light on and off

The light is switched off and on again with the but-

ton BLACKOUT (17) on the remote control. With

the light switched off (Blackout) the display (14) of

the remote control is dark.

It is possible to select another colour or another

light programme with the light switched off (



the

following chapters). Then the selection is shown on

the display (14) but will only be active when the but-

ton BLACKOUT is pressed again.

5.3.2 Programmes

The following programmes may be selected with

the button MODE (16):

The lighting colour changes automatically

with slow fadings.

The lighting colour is changed by music

control.

The lighting colour is changed by music

control, partly with running light effects for

several spotlights.

Music-controlled stroboscope in white

Music-controlled stroboscope with chang-

ing colours, partly opposite for several

spotlights.

For music control the remote control has a micro-

phone (19) of its own. Adjust the control SENSI-

TIVITY (20) for the microphone sensitivity so that

the dynamic power of the music is reproduced by

the spotlight in an optimum way. For programmes

and , the colours are automatically

changed during music breaks after a few seconds.

The programme last selected is automatically saved.

5.3.3 Colour spotlight with selectable colour

The following colours can directly be selected with

the button COLOUR (15):

white

red

green

blue

purple

cyan

yellow

pink

orange

light green

The colour last selected is automatically saved.

5.4 Operation via a light controller

For operation via a light controller with DMX512

protocol (e. g. DMX-1440 or DMX-510USB by “img

Stage Line”), the PARL-12DMX is equipped with

four DMX control channels. The functions of the

channels and the DMX values can be found in

chapter 7.1.

5.4.1 DMX connection

For the DMX connection, the unit is provided with

3-pole XLR jacks of the following pin configuration:

Pin 1 = ground, 2 = DMX

-

, 3 = DMX+

For connection, special cables for high data flow

should be used. Standard microphone cables with

screening and a minimum cross section of 2 ×

0,22 mm

2

and with a capacity as low as possible

can only be recommended for a total cable length

of up to 100 m. For cable lengths exceeding 150 m

it is recommended to insert a DMX level matching

amplifier (e. g. SR-103DMX by “img Stage Line”).

1) Connect the DMX input (12) to the DMX output

of the light controller.

13

GB

2) Connect the DMX output (13) to the DMX input

of the following light effect unit. Connect its out-

put again to the input of the following unit, etc.

until all light effect units have been connected in

a chain.

3) To prevent interference in signal transmission,

for long cables or a great number of units con-

nected in series, terminate the DMX output of

the last DMX unit in the chain with a 120 Ω resis-

tor (> 0.3 W): Connect a corresponding termi-

nating plug (e. g. DLT-123 by “img Stage Line”)

to the output jack.

5.4.2 Adjusting the start address

To be able to operate the spotlight with a light con-

troller, adjust the DMX start address for the first

DMX channel. If e. g. address 17 on the DMX con-

troller is provided for controlling the red LEDs,

adjust the start address 17 on the spotlight. Then

the other DMX functions of the spotlight are auto-

matically assigned to the following addresses (in

this example 18, 19 and 20). The address 21 could

be used in this example as the next possible start

address for the following DMX-controlled unit.

1) Press the button FUNC (6).

2) Select the function with the button UP or

DOWN and confirm with the button ENT. The

display (5) shows and behind it the present

DMX start address flashing.

3) Use the button UP or DOWN to adjust the

desired start address and confirm with the but-

ton ENT. The display stops flashing and the

spotlight is ready to receive control signals.

5.4.3 DMX control

To be able to operate the spotlight with the DMX

controller, the display must show and behind it the

start address. If not, make the steps described in

chapter 5.4.2 to adjust the start address. The

reception of control signals is indicated by a flash-

ing dot behind the first position on the display.

If the display shows , the spotlight is in the

DMX control mode but no DMX control signal is

present at the jack DMX INPUT (12).

6 Cleaning the Unit

The plastic pane in front of the LEDs should be

cleaned at regular intervals from the outside,

depending on impurities caused by dust, smoke or

other particles. Only this will ensure that the light is

radiated at maximum brightness. For cleaning,

disconnect the mains plug from the socket. Only

use a soft, clean cloth and a mild detergent. Then

wipe the plastic pane dry.

For cleaning the other parts of the housing, only

use a soft, clean cloth. Never use any fluid; it may

leak into the unit and cause damage.

14

GB

7 Specifications

PARL-12DMX

Light source: . . . . . . . . . . 153 LEDs

Red: 51, green: 51,

blue: 51

Diameter: . . . . . . . . . . . 10 mm

Beam angle: . . . . . . . . . 25°

Power supply: . . . . . . . . . 230 V~ / 50 Hz

Power consumption: . . . . 45 VA max.

Ambient temperature: . . . 0 – 40 °C

Dimensions: . . . . . . . . . . . 270 × 210 × 100 mm

Weight: . . . . . . . . . . . . . . 2 kg

FS-2PARL

Dimensions: . . . . . . . . . . . 230 × 50 × 175 mm

Weight: . . . . . . . . . . . . . . 1 kg

Connection, cable length: RJ45, 6 m

Power supply: . . . . . . . . . via PARL-12DMX

7.1 DMX channels

Subject to technical modification.

DMX value Function

Channel 1

0 – 255 brightness red

Channel 2

0 – 255 brightness green

Channel 3

0 – 255 brightness blue

Channel 4

0– 7 light off

8 – 190

dimmer dark → bright

colour mixing via channel 1 – 3

191 – 200 music-depending colour change

201 – 247

stroboscope slow → fast

colours and brightness via channel 1 – 3

248 – 255

no stroboscope

colours and brightness via channel 1 – 3

15

GB

®

INTERNATIONAL GmbH & Co. KG. No part of this instruction manual

may be reproduced in any form or by any means for any commercial use.

Page is loading ...

MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany

Copyright

©

®

IMG Stage Line PARL-12DMX User manual

IMG Stage Line PARL-12DMX User manual

in other languages

Related papers

Other documents