Whirlpool GZ9730SSS0 Owner's manual

30"(76.2CM) AND 36" (91.4 CM)

WALL-MOUNTCANOPY RANGEHOOD

HOTTEDE CUISINI_: POUR MONTAGE MURAL

30" (76,2 CM) 36" (91,4 CM)

Table of Contents/Table des matieres ............................................................................. 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY.

iMPORTANT : LIRE ET CONSERVER CES INSTRUCT_ONS. POUR UT_USATION RC:SIDENTIELLE UNIQUEMENT.

W10029770A

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Venting Requirements (vented models only) ............................... 5

Electrical Requirements ............................................................... 6

INSTALLATION INSTRUCTIONS .................................................. 7

Prepare Location .......................................................................... 7

Install Mounting Bracket .............................................................. 7

Install Flue Mounting Bracket ...................................................... 8

Prepare Range Hood ................................................................... 8

Install Range Hood ....................................................................... 9

Complete Installation ................................................................. 12

RANGE HOOD USE ...................................................................... 12

Range Hood Controls ................................................................ 12

RANGE HOOD CARE ................................................................... 12

Cleaning ...................................................................................... 12

WIRING DIAGRAM ...................................................................... 14

ASSISTANCE OR SERVICE ......................................................... 15

In the U.S.A ................................................................................ 15

Accessories ................................................................................ 15

In Canada ................................................................................... 15

WAR RANTY .................................................................................. 16

TABLEDESMATIERES

SI_CURITI_ DE LA HOTTE DE CUISINII_RE ............................... 17

EXIGENCES D'INSTALLATION ................................................... 19

Outillage et pieces ...................................................................... 19

Exigences d'emplacement ......................................................... 19

Exigences concernant I'evacuation

(seulement pour modeles avec decharge a I'exterieur) ............. 20

Specifications electriques .......................................................... 21

INSTRUCTIONS D'INSTALLATION ............................................. 22

Preparation de I'emplacement ................................................... 22

Installation de la bride de montage ............................................ 22

Installation de la bride de montage du cache-conduit .............. 23

Preparation de la hotte de cuisiniere ......................................... 23

Installation de la hotte de cuisiniere ........................................... 24

Achever I'installation .................................................................. 27

UTILISATION DE LA HOTTE DE CUISINII_RE ........................... 28

Commandes de la hotte de cuisiniere ....................................... 28

ENTRETIEN DE LA HOTTE DE CUISINII_RE ............................. 28

Nettoyage ................................................................................... 28

SCHI_MA DE CABLAGE ............................................................... 30

ASSISTANCE OU SERVICE ......................................................... 31

Liste d'accessoires ..................................................................... 31

Au Canada .................................................................................. 31

GARANTIE ..................................................................................... 32

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

[] Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

[] Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

[] Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

[] Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

[] When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

[] Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RiSK OF iNJURY TO

PERSONS iN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: _

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill

• %6" (8 mm) drill bits for pilot holes

• %2" (4 mm) drill bits

• Pencil

• Tape measure or ruler

• Caulking gun and weatherproof caulking compound

• Phillips screwdriver

• Vent clamps

• Metal snips

For vented installations, you will also need:

• 1wall or roof cap

• Metal vent system

For non-vented (recirculation} installations, you will also

need:

• Charcoal Filter Kit Part Number 8212566

See "Assistance or Service" section to order.

• 5" (12.7 cm) diameter expandable/flexible aluminum duct

• Vent clamps for a 6" (15.2 cm) diameter duct

Parts supplied

Remove parts from packages. Check that all parts are included.

• Literature package

• Decorative flue assembly

• 2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

• Parts bag containing:

• Damper

• Mounting bracket

• Flue mounting bracket

• 8 drywall anchors

• 8 - 4.8 x 38 mm pan head mounting screws

• 6- 3.9 x 9.5 mm pan head screws

• 2 - 3.9 x 5.7 mm flat head screws

IMPORTANT: Observe all governing codes and ordinances.

It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The model/

serial rating plate is located behind the left filter on the rear wall of

the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance. Consult the cooktop/

range manufacturer installation instructions before making any

cutouts.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installations" in "Prepare Location" section.

Charcoal Filter Kit Part Number 4393848 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

101%6,, 81¾_"

(27.8 cm) (25.2 cm)

30" (76.2 cm)

or

36" (91.4 cm)

(49.8 cm)

Installation Dimensions

30" (76.2 cm)

or

35" (91.4 cm)

1

12" (30.5 cm) min.

max.

24" (61 cm) rain.

30" (76.2 cm) suggested max.

...... J

........................ /

• Vent system must terminate to the outdoors, except for non-

vented (recirculating)installations.

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall cap.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

For the most efficient and quiet operation:

• Use a straight run or as few elbows as possible.

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a nonmetallic thermal break should

be installed to minimize conduction of outside temperatures as

part of the vent system. The damper should be on the cold air

side of the thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This canopy hood is factory set for venting through the roof or

wall.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall. To vent

through a wall, a 90° elbow is needed.

Rear discharge

A 90°elbow may be installed immediately above the hood.

For non-vented (recirculating) installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting an activated carbon filter and the deflector. Fumes

and vapors are recycled through the top grille.

Roof Venting WallVenting Non-vented

(recirculating)

B

A. Roof cap A. Wail cap A. Deflector

B. 6" (15.2 cm) B. 6" (15.2 cm) B. 6" (15.2 cm)

round vent round vent round vent

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm} Round

45° elbow 2.5 ft

(o.8m)

Example vent system

Wall cap

90 ° elbow

(0.6m)

!_

The following example falls within the maximum vent length of

35 ft (lO.7 m).

1 - 90 ° elbow = 5.0 ft (1.5 m)

1 - wall cap = O.0 ft (0.O m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Observe all governing codes and ordinances. A 120 Volt, 60 Hz.,

AC only 15-amp fused, electrical supply (or circuit breaker) is

required. (Atime-delay fuse or circuit breaker is recommended.) It

is recommended that a separate circuit serving only this

appliance be provided.

Set the grounded 3 prong outlet within the space covered by the

decorative flues.

GROUNDING iNSTRUCTiONS

[] For all cord connected appliances:

The range hood must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric

current. The range hood is equipped with a cord having a

grounding wire with a grounding plug. The plug must be

plugged into an outlet that is properly installed and

grounded.

WARNING: Improper use of the grounding plug can

result in a risk of electric shock. Consult a qualified

electrician or serviceman if the grounding instructions are

not completely understood, or if doubt exists as to whether

the range hood is properly grounded.

Do not use an extension cord. If the power supply cord is

too short, have a qualified electrician or serviceman install

an outlet near the range hood.

SAVE THESE iNSTRUCTiONS

90° elbow 5.0 ft

(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

INSTALLATIONINSTRUCTIONS

• It is recommended that the vent system be installed before

hood is installed.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check your ceiling height and the hood height maximum

before you select your hood.

• To avoid damage or dirt, place a thick, heavy covering over

countertop, cooktop, or range.

1. Disconnect power to outlet.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

5. Determine and mark the centerline on the wall where the

range hood will be installed.Mark location of mounting

bracket on wall section using the dimensions shown.

A

A. Framing behind drywall (optional)

B. 51A6'' (12.9 cm)

C. 38V_6"(96. 7 cm) = bottom of hood 24" (61 cm) above cooktop

44V_6"(111.9 cm) = bottom of hood 30" (76.2 cm) above cooktop

D. Centerline

E.Hood mounting bracket

Wall-Mount Installation - Style 1

1. Drill two sA6"(8 mm) pilot holes for drywall anchors.

2. Install drywall anchors.

3. Attach the hood mounting bracket to the wall using

two 4.8 x 38 mm pan head mounting screws.

A. 5_Ae'' (12.9 cm)

B. 38V_6" to 44V_6"(96. 7 cm to 111.9 cm) above cooktop

C. Centerline

On 8 ft (2.4 m) ceilings, the required hood distance above the

cooktop is a minimum of 24" (61 cm) and a suggested maximum

of 30" (76.2 cm) for vented installations. For non-vented

(recirculating) installations, the minimum is 24" (61 cm) and the

suggested maximum is 28" (71.1 cm).

On 9 ft (2.7 m) ceilings, the required hood distance above the

cooktop is a minimum of 26" (66 cm) and a suggested maximum

of 30" (76.2 cm). The air vents on the upper decorative flue will be

exposed after installation.

• For ceilings from 9 ft (2.7 m) to 10 ft (3 m), purchase the

optional Chimney Extension Kit Part Number 8212565. See

"Assistance or Service" to order. The hood distance above

the cooktop is minimum of 24" (61 cm) and a suggested

maximum of 30" (76.2 cm). The air vents on the upper

decorative flue will be exposed after installation if the range

hood is mounted 24 - 27" (61 - 68.6 cm) from the cooktop.

Chimney Extension Kit (Optional)

Follow instructions provided with kit.

• Chimney Extension Kit Part Number 8212565. See

"Assistance or Service" to order.

Wood Frame Installation - Style 2

(optional before drywall installation)

Construct wood wall framing so that it is flush with interior

surface of wall studs. The framing must be centered over the

installation location. The height of the framing must allow for

the mounting bracket to be secured to the framing within the

dimensions shown.

5. Attach the flue mounting bracket to the ceiling using

two 4.8 x 38 mm pan head mounting screws.

A

A. 5V_e"(12.9 cm)

B. 38V_6" to 44V_" (96. 7 cm to 111.9 cm) above cooktop

C. Centerfine

2. After the wall surface is finished, drill two %2" (4 mm) pilot

holes.

3. Install the mounting bracket to the frame using

two 4.8 x 38 mm pan head mounting screws.

.... _ (,_<:c_ .......

Assemble the flue mounting bracket by attaching the 2 side

brackets to the center bracket using the 2 flat head bracket

screws provided. Adjust outside width as shown,

,/ /"

A. 3.9 x 5.7 mm flat head bracket screws

B. 9W_6"(24.9 cm)

2. Center the mounting bracket directly over the range hood

location.

3. Drill two s/_6"pilot holes for drywall anchors.

4. Install drywall anchors.

C

il_ _

" i D

A. Flue mounting bracket

B. Hood mounting bracket

C. Centerline

D. Cooktop surface

NOTE: Remove the plastic film from all exterior surfaces of the

hood and decorative flues, prior to final installation,

Vented Installation

Installthe damper into the duct connector of the range hood.

A

i

B

A. Damper

B. Duct connector

Non-vented (recirculating) Installation

Damper supplied with hood is not required in a non-vented

(recirculating) installation. Install the 5" (12.7 cm) to 6" (15.2 cm)

adapter supplied with the Charcoal Filter Kit, Part Number

8212566. See "Assistance or Service" section to order.

A

A. 5" (12.7 cm) to 6" (15.2 cm) adapter

B. Blower collar

Page is loading ...

SCHI_MADECABLAGE

CARTE DE CIRCUITS -

VITESSE DU VENTILATEUR

VITESSE 1 2 I 3

i

CONTACT 1-2 1-8 1-9

CARTE DE CiRCUiTS - ALLUMAGE

ARR_:T MARCHE

2-4 4-6

1-3 3-5

SE1L7A

BO|TIER DE RACCORDEMENT

w

(5

Z

cr

O

BL

N

BL

ORANGE

]

0 0 ? O

2 4 16 8

IC°C-v°v|

o

10

9

?-

t_

LU

b=

t_

o

[L

_0

z

t_

F--

)

LAMPES

(

Z

{

= cDcAI I

ORANGE

=J

m

/L N

JA-VE T _

L-GRN__

w

>,

( "x__f a j

Vitesse Mesure entre R6sistance

du moteur conducteur ROUGE et (Ohms)

1 Noir 22

2 Orange 27

3 Blanc 32

30

Page is loading ...

Whirlpool GZ9730SSS0 Owner's manual

This manual is also suitable for

Whirlpool GZ9730SSS0 Owner's manual

in other languages

Related papers

Other documents