Shure Beta 87A Kondensator Vocalmikrofon User manual
- Category
- Microphones
- Type
- User manual
BETA 87A
SUPERCARDIOID CONDENSER MICROPHONE
The Shure Model BETA 87A is a premium quality supercar-
dioid hand-held electret condenser vocal microphone with ex-
ceptionally smooth frequency response and high sound pres-
sure level (SPL) capability. Used for professional sound
reinforcement, broadcasting, and studio recording applica-
tions, the BETA 87A combines superb performance with the
ruggedness needed for touring and field production.
The BETA 87A features a controlled low-frequency roll-off
that compensates for proximity effect and prevents the “boomy”
sound often associated with close pick-up. The characteristic
Shure presence rise brightens the upper midrange. The tight
supercardioid pattern, with null points at approximately 125°,
provides maximum isolation from other vocalists or instruments
while offering minimal off-axis coloration. The BETA 87A oper-
ates on phantom power.
Features:
• Smooth frequency response with gradual presence rise
• Highly consistent supercardioid polar pattern provides
superior gain-before-feedback
• Electronic low-frequency roll-off compensates for proximity
effect
• Wide dynamic range (117 dB) and low distortion character-
istics
• Very low susceptibility to RFI and electromagnetic hum
• Advanced cartridge shock-mount system absorbs mechan-
ical shocks and reduces handling noise
• Built-in pop filter reduces undesirable wind and breath
sounds
• Reliability for years of trouble-free performance
APPLICATION AND PLACEMENT
Some of the most common applications and placement
techniques are listed in the following table. Keep in mind that
microphone technique is largely a matter of personal taste—
there is no one “correct” microphone position.
SUGGESTED MICROPHONE
PLACEMENT
TONE QUALITY
Lips less than 6 inches (15 cm) away
or touching the windscreen, on axis to
microphone.
Robust sound, emphasized
bass, maximum isolation from
other sources.
6 inches to 2 feet (15 to 60 cm) away
from mouth, just above nose height.
Natural sound, reduced bass.
8 inches to 2 feet (20 to 60 cm) away
from mouth, slightly off to one side.
Natural sound, reduced bass
and minimal ”s” sounds.
3 to 6 feet (90 cm to 1.8 m) away. Thinner, distant sound; notice-
able levels of ambient noise.
General Rules for Microphone Use
1. Aim the microphone toward the desired sound source and at
a 125° angle away from unwanted sources. Don’t place un-
wanted sound sources directly to the rear of the microphone
since supercardioid microphones, such as the BETA 87A,
have a narrow pick up range at about 180°. Refer to Figure 1.
2. Place the microphone as close as practical to the desired
sound source. Refer to the table above.
3. Use only one microphone for each sound source.
4. Keep the distance between microphones at least three times
the distance from each source to its microphone.
5. Place microphones as far as possible from reflective sur-
faces.
6. Work close to the microphone for extra bass response.
7. Use the fewest number of microphones as is practical.
8. Add a windscreen when using the microphone outdoors.
9. Avoid excessive handling to minimize pick up of mechanical
noise and vibration.
10. Do not cover any part of the grille with your hand.
180
o
125
o
125
o
90
o
0
o
90
o
CORRECT
0
o
90
o
180
o
INCORRECTCORRECT
125
o
90
o
0
o
180
o
90
o
90
o
POSITIONING UNWANTED SOUND SOURCES
FIGURE 1
Model BETA 87A User Guide
27D2965 (Rev. 7)
2005, Shure Incorporated
Printed in U.S.A.
2
OPERATION
Power
The BETA 87A requires phantom power. This may be sup-
plied to the microphone from an external power supply (such as
the Shure model PS1A) or directly from preamplifiers, mixers,
or consoles with built-in phantom power. Suitable sources
should provide 11 to 52 Vdc phantom voltage.
Proximity Effect
Unidirectional microphones such as the BETA 87A progres-
sively boost bass frequencies by 10 to 15 dB at 100 Hz when
the microphone is at a distance of about 6 mm (1/4 in.) from the
sound source. This phenomenon, known as proximity effect,
creates a warmer, more powerful sound. To prevent explosive
low frequency sound during close-up use, the BETA 87A bass
response gradually rolls off. This provides greater control and
helps the user take advantage of proximity effect.
Wind Noise
The BETA 87A has an integral wind and pop filter providing
excellent protection against most wind and breath noise. Under
adverse conditions, such as high winds or close proximity to a
“problem” vocalist, the optional foam windscreen can be used.
Impedance
Use a minimum load impedance of 800 ohms for maximum
signal handling and minimum distortion. The load may be as
low as 150 ohms, but a reduction in output signal strength and
output clipping level results.
SPECIFICATIONS
Cartridge Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz (see Figure 2)
Polar Pattern
Supercardioid (see Figure 3)
Output Impedance
Rated at 150 ohms (100 ohms actual ±20%)
Recommended minimum load impedance: 800 ohms
Sensitivity (at 1,000 Hz)
Open Circuit Voltage –52.5 dBV/Pa (2 mV). . . . . . . . . . . . . . . . .
(1 Pa = 94 dB SPL)
Clipping Level (at 1,000 Hz)
1000 ohm Load –6 dBV (0.5 V). . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum SPL (at 1,000 Hz)
140.5 dB (0.25% THD, 1000 ohm load)
Self-Noise (equivalent sound pressure level; measured with true
rms voltmeter)
23.5 dB typical, A-weighted
25.5 dB typical, weighted per DIN 45 405
Dynamic Range
117 dB (maximum SPL to A-weighted noise level)
Signal-to-Noise Ratio
70.5 dB at 94 dB SPL (IEC 651)*
Polarity
Positive pressure on diaphragm produces positive voltage on pin
2 relative to pin 3
Power
Phantom Supply Requirement 11 to 52 Vdc, positive. . . . . . . . .
at both pins 2 and 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Drain 1.0 to 1.2 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector
Three–pin (XLR) professional audio
Case
Aluminum construction with blue metallic finish, and hardened
steel grille with nickel satin chrome plating
Dimensions
See Figure 4
Net Weight
207 grams (7.6 oz)
*S/N ratio is difference between 94 dB SPL and equivalent SPL of self–
noise A-weighted.
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC Directive
89/336/EEC. Meets applicable tests and performance criteria in
European Standard EN55103 (1996) parts 1 and 2, for residential
(E1) and light industrial (E2) environments.
FURNISHED ACCESSORIES
Swivel Adapter A25D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrying/Storage Bag 26A13. . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONAL ACCESSORIES
Phantom Power Supply PS1A. . . . . . . . . . . . . . . . . . . . . . . .
Isolation Mount A55M, A55HM. . . . . . . . . . . . . . . . . . . . . . . .
Windscreen A85WS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable (7.6 m—25 ft) C25F. . . . . . . . . . . . . . . . . . . . . . . . . . .
REPLACEMENT PARTS
Grille RK312. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cartridge R193. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement Amplifier Assembly 90KF2600. . . . . . . . . . . .
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
11
9876543298765
20000100001000
432
100
5020
0
+10
–10
TYPICAL FREQUENCY RESPONSE
RÉPONSE EN FRÉQUENCE TYPIQUE
TYPISCHER FREQUENZGANG
RESPUESTA DE FRECUENCIA TIPICA
RISPOSTA IN FREQUENZA TIPICA
FIGURE 2 S ABBILDUNG 2 S FIGURA 2
150
o
120
o
150
o
120
o
180
o
30
o
60
o
90
o
30
o
60
o
90
o
–5 dB
–10 dB
–15 dB
–20 dB
0
1000 Hz
500 Hz
250 Hz
150
o
120
o
150
o
120
o
180
o
30
o
60
o
90
o
30
o
60
o
90
o
–5 dB
–10 dB
–15 dB
–20 dB
0
10000 Hz
6300 Hz
2500 Hz
TYPICAL POLAR PATTERN
COURBE DE DIRECTIVITÉ TYPIQUE
TYPISCHE RICHTCHARAKTERISTIK
PATRON POLAR TIPICO
DIAGRAMMA POLARE TIPICO
FIGURE 3 S ABBILDUNG 3 S FIGURA 3
21 mm
(
53
/
64
in.)
51 mm
(2 in.)
OVERALL DIMENSIONS
DIMENSIONS HORS TOUT
GESAMTABMESSUNGEN
DIMENSIONES GENERALES
DIMENSIONI COMPLESSIVE
FIGURE 4 S ABBILDUNG 4 S FIGURA 4
10 mm (3/8 in.)
0.6 m (2 ft.)
192 mm
(7–
9
/
16
in.)
Hz
dB
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Shure Beta 87A Kondensator Vocalmikrofon User manual
- Category
- Microphones
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
Other documents
-
Pyle PDMIC78 Owner's manual
-
Pyle PDMIC58 User guide
-
Optimus B-F50XS User manual
-
Work-pro XS 111 PRO User manual
-
-
Sense SE-300-CM-W Quick start guide
-
-
AKG Acoustics C 4500 B-BC User manual
-
Olimpia Splendid 99615 Datasheet
-
