Whirlpool LL 42 User guide

Page is loading ...

DISHWASHER

Contents

Installation, 14-15

Positioning and levelling

Connecting the water and electricity supplies

Technical data

Description of the appliance, 16

Overall view

Control panel

Loading the racks, 17

Lower rack

Cutlery basket

Upper rack

Start-up and use, 18

Starting the dishwasher

Loading the detergent

Washing options

Wash cycles, 19

Wash cycle table

Rinse aid and refined salt, 20

Loading the rinse aid

Loading the refined salt

Care and maintenance, 21

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the filters

Leaving the machine unused for extended periods

Precautions and advice, 22

General safety

Disposal

Saving energy and respecting the environment

Troubleshooting, 23

Assistance, 24

Before calling for Assistance

English, 13

EN

Instruction booklet

LL 43

14

EN

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

If the appliance must be moved at any time, keep it

in an upright position; if absolutely necessary, it may be

tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop (see the Assembly instruction

sheet

* ).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position (the angle of

inclination must not exceed 2 degrees). If the appliance is

levelled correctly, it will be more stable and much less

likely to move or cause vibrations and noise while it is

operating.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new piping.

- Do not use old piping.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned towards the

right or the left in order to achieve the best possible

installation (see figure).

Connecting the water inlet hose

 To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

a ¾ gas threaded connection.

 To a suitable hot water connection point: your

dishwasher may be provided with hot water from the

mains supply (if you have a central heating system

with radiators) provided that it does not exceed a

temperature of 60°C.

Screw the hose to the tap as described for

connection to a cold water supply.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (see

Assistance).

The water pressure must be within the values

indicated in the Technical data table (see below).

The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

- is provided with a Water Stop

* safety device, in other

words it has a water inlet hose that consists of a

transparent hose on the outside and a red hose on the

inside: both the hoses can withstand extremely high

pressure. If the internal hose breaks, the external hose

becomes a bright red colour and carries the water

instead, thus avoiding any leakage.

It is very important to check the external hose

regularly: if it is a bright red colour, it must be replaced

by an authorised technician as soon as possible (see

Assistance).

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be

cut as it contains live electrical parts.

* Only available in selected models.

Installation

15

EN

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm. Alternatively, rest

it over a sink or tub; the free end of the hose should not

remain immersed in water.

The special plastic elbow

*

makes it easier to find the

best layout: fix the elbow to

the wall securely in order to

prevent the outlet hose from

moving and spilling the dirty

water.

The part of the hose marked

with the letter A should be

between 40 and 100 cm

above the ground (see

figure).

We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

 the socket is earthed and complies with current

regulations;

 the socket can withstand the maximum load of the

appliance, which is indicated on the data plate

located on the inside of the door (see Description of

the appliance);

 the power supply voltage falls within the values

indicated on the data plate on the inside of the door;

 the socket is compatible with the plug of the

appliance. If this is not the case, ask an authorised

technician to replace the plug (see Assistance); do

not use extension cables or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket should be easily

accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be

replaced by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See

Assistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill the

salt dispenser with water and add approximately 2 kg of

salt (see Rinse aid and refined salt). The water may

overflow: this is normal and is not a cause for concern.

It is also normal that the LOW SALT

* indicator light

continues to flash for a few cycles after the salt has been

loaded.

If the salt container is not filled, the water softener

and the heating element may be damaged as a result.

* Only available in selected models.

Technical data

A

Dimensions

width 45 cm

height 85 cm

depth 60 cm

Capacity 9 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

4.3 psi – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-73/23/EEC dated 19/02/73

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE Waste Electrical

and Electronic Equipment

(WEEE)

16

EN

Overall view

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control panel

***

*** Only total built-in models

* Only available in selected models.

Description of the appliance

Control panel

ON-OFF

indicator light

ON-OFF button

Wash Cycle Phase

and Delayed start*

indicator lights

WASH CYCLE

indicator light

Wash Cycle Select

button

Low Salt

indicator light*

START/RESET

button

PRE-WASH

WASH

DRYING

RINSES

Low Rinse Aid

indicator light*

Delayed Start

button*

17

EN

1

2

3

4

Loading the racks

Open the left and right guide rail

stops and pull out the rack; position

it higher or lower as required, slide it

along the guide rails until the front

wheels are in place and close the

stops (see figure).

If the rack is equipped with the click

clack handles

* (see figure), pull

them upwards or downwards to

adjust the height.

Loading examples for the upper rack

Loading examples for the lower rack

Items that should not be washed in the dishwasher

 Wooden items, objects with wooden or horn handles or

glued-on parts.

 Items made from aluminium, copper, brass, pewter or tin.

 Items made from plastic that is not heat-resistant.

 Antique or hand-painted porcelain.

 Antique silver. Silver that is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other

metals.

We recommend the use of crockery which is dishwasher

safe.

* Only available in selected models.

** The number and position may vary.

Before loading the racks, remove all food residues from

the crockery and empty liquids from glasses and cups.

After loading the appliance, check that the sprayer arms

can rotate freely.

Lower rack

The lower rack can hold pans, lids, plates, salad bowls,

cutlery, etc. as seen in the Loading examples.

Plates and large covers should be placed at the sides of the

rack, ensuring that they do not block the rotation of the upper

sprayer arm.

Some dishwasher models are fitted

with tip-up sections

*, which can be

used in a vertical position when

arranging plates or in a horizontal

position when arranging pans and

salad bowls.

Cutlery basket

The type of cutlery basket may vary according to the

dishwasher model.

Knives and other utensils with sharp edges must be

placed in the cutlery basket with the points facing downwards,

or they must be positioned horizontally in the tip-up

compartments on the upper rack.

The grille element

* may be positioned in the basket to separa-

te the cutlery: place the pieces of cutlery into the appropriate

compartments with the handles at the bottom.

If the rack has side baskets, the spoons should be loaded

individually into the appropriate slots

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

tea and coffee cups, saucers, small salad bowls, saucepans

and small saucepans that are not too soiled, using the Loading

examples as a guide.

 Lightweight crockery: position these dishes so that they

will not be moved by the jets of water.

 Mugs and cups: place these on the tip-up

compartments

**.

 Long sharp knives and serving utensils: place these on

the tip-up compartments

**.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper

rack may be moved to a higher or lower level.

The height of the upper rack should ideally be

adjusted WHEN THE RACK IS EMPTY.

Never lift or lower the rack on one side only.

18

EN

Starting the dishwasher

1. Open the water inlet valve.

2. Press the ON/OFF button: the machine will emit a

beep and the ON/OFF indicator light will illuminate.

3. Open the door and measure out a suitable amount of

detergent (see below).

4. Load the racks (see Loading the racks) and shut the

door.

5. Select the wash cycle by pressing the SELECT WASH

CYCLE button: the corresponding indicator light will

illuminate.

6. Select the wash options (see below).

7. Start the cycle by pressing the START/RESET button:

the machine will emit a confirmation beep. The WASH

CYCLE PHASE indicator lights display the status of the

cycle:

Pre-wash, Wash, Rinse, or Drying.

8. At the end of the cycle two short beeps will sound and

the DRYING indicator light will flash. Switch off the

appliance by pressing the ON/OFF button and close the

water inlet valve.

9. Open the door and wait for a few minutes before

removing the crockery inside, in order to avoid burns.

Unload the racks, beginning with the lower level.

Modifying the duration of a wash cycle already in

progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that

it has only just begun:press and hold the START/RESET

button for 5 seconds After one long beep and three short

beeps, the WASH CYCLE PHASE indicator light will

switch off: select the new cycle and switch the machine

back on by pressing the START/RESET button.

Adding extra crockery

Press the ON/OFF button and open the door, taking care

to avoid the escaping steam, and place the crockery

inside the dishwasher. Press the ON/OFF button again:

the cycle starts from the point at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is

a power cut, the cycle stops. It starts again from the point

at which it was interrupted once the door has been shut

or the electricity supply is restored.

Loading the detergent

A successful wash also depends on the correct

amount of detergent being used, as

recommended by the manufacturer. Exceeding

the recommended amount does not result in a

more effective wash and pollutes the

environment.

Only use detergent which has been

specifically designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

To obtain the best results from each washing

and drying cycle, powder detergent, rinse aid liq-

uid and salt should be used.

compartment A: Washing detergent

compartment B: Pre-wash detergent

1. Open cover C by pressing

button D.

2. Pour in the detergent after

consulting the Wash cycle table:

 for powder detergent use

compartments A and B

 for tablets, when the cycle

requires 1 tablet, place it in

compartment A and close the

cover; when it requires 2, place

the second tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Washing options

Delayed start

It is possible to delay the start time of the cycle by 12, 9,

6 or 3 hours.

1. Press the DELAYED START button: every time the

button is pressed, a beep is emitted and the selected

delayed start indicator light illuminates.

2. Select the wash cycle and press the START/RESET

button: after the beep sounds, the timer begins

counting down.

3. Once this time has elapsed, the indicator light

switches off and the wash cycle begins.

To adjust the delay time and select a smaller period of

time, press the DELAYED START button. To cancel it,

press the button repeatedly until the wash cycle begins

and the WASH CYCLE PHASE indicator light

corresponding to the start of the cycle in progress

illuminates.

Start-up and use

* Only available in selected models.

19

EN

Wash cycle table

Note

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 grams of powder = approximately 15 ml of liquid

1 teaspoon = 5 grams of powder = approximately 5 ml of liquid

Ariston dishwashers are fitted with an automatic filter cleaning system that may increase the cycle duration.

Wash cycles

The number and type of wash cycles and options may vary depending on the dishwasher model.

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash

cycles it uses less energy and is les harmful to the environment.

If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dish-

washer, reduce the amount of detergent used accordingly.

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle selection

instructions

Wash cycle

Powder Liquid Tablets

Drying

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Extremely soiled dishes

and pans (not to be

used for delicate items).

Super Wash

24 g (A)

3 g (B)

24 ml (A)

3 ml (B)

No Yes 2.00’

Normally soiled pans

and dishes. Standard

daily wash cycle.

Normal

27 g (A) 27 ml (A) No Yes 1:33’

Environmentally-

friendly

* wash cycle

with low energy

consumption levels,

suitable for pans and

dishes.

24 g (A)

3 g (B)

24 ml (A)

3 ml (B)

No Yes 2:25’

Economic and fast

wash cycle to be used

for lightly soiled dishes.

(Run cycle immediately

after use.)

Rapid & Dry

20 g (A) 20 ml (A) No Yes 0:44’

Preliminary wash cycle

for dishes while the load

is awaiting completion

with the dishes from the

next meal. Soak

No No

No No 0:12'

Special cycle to be used

for more delicate items

which are sensitive to

high temperatures. Run

cycle immediately after

use. Crystal

20 g (A) 20 g (A) No

Yes

1:30’

20

EN

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

If you do not add salt or rinse aid, the LOW SALT*

and LOW RINSE AID* indicator lights will flash

continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs

off surfaces more readily and therefore does not leave streaks

or marks.

The rinse aid dispenser should be filled:

 whenever the indicator light (H) signals that it is empty.

Illuminated light: add rinse aid; unlit light: there is no

shortage of rinse aid in the dispenser.

 when the LOW RINSE AID

* indicator light on the panel

flashes;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry

cloth.

3. Screw the lid back on.

NEVER pour the rinse aid

directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the washing or drying

results, you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster to one of the 6 pre-set

positions (the default position is set to 4):

 if there are white streaks on the crockery, set the adjuster

to a lower number (1-3).

 if drops of water remain on the crockery or there are

limescale marks present after the cycle has finished, set the

adjuster to a higher number (4-6).

If you are using multi-functional tablets and you wish to

further improve the drying performance of the appliance, fill

the dispenser and set the dosage adjuster to 2.

Loading the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the dispenser is never empty. Refined salt

removes limescale from the water, thus avoiding the formation

of deposits on crockery. The salt dispenser is located in the

lower part of the dishwasher (see Description) and should be

filled:

 when the green float

* cannot be seen by simply looking at

the cap of the salt dispenser;

 when the LOW SALT

* indicator light on the panel flashes;

 if your machine is not equipped with an indicator light or a

green float:

approximately every 30 wash cycles;

1. Remove the lower rack and unscrew

the cap of the dispenser (in an anti-

clockwise direction).

2. For the first wash cycle only: fill the

dispenser up to the edges with water.

3. Position the funnel

* provided

correctly (see figure) and fill the salt

dispenser up to the edges (approximately 2 kg); it is normal

for a little water to leak out.

4. Remove the funnel*, wipe away any salt residue from the

thread and screw the cap on tightly, so that detergent does

not leak into the dispenser during the wash cycle (this could

damage the water softening system beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

Adjusting the amount of salt*

It is possible to adjust the amount of salt used according to the

hardness of the water in your area (this information is available

from your local water board).

1. Unscrew the dispenser cap.

2. Turn the arrow on the neck of the

dispenser (see figure) towards the + or -

symbols, using the table below as a

guide.

The default setting of the water softening system is +.

- If using multi-functional tablets fill the salt dispenser and set the

adjuster to -; if the hardness of the water is greater than 60°fH,

set it to +.

* Only available in selected models.

G

H

F

Rinse aid and refined salt

Hardness of the water

°dH °fH °mmol/l

Selector

knob

position

Salt

consumption

(grams/cycle)

Autonomy

(cycles/2 kg)

0 - 10 0 - 17 0 - 1.7 / 0 /

10 – 25

18 – 44

1.8 – 4.4

- 20 60

25 – 50

45 – 89

4.5 – 8.9

MED 40 40

> 50 > 89 > 8.9 + 60 25

21

EN

Shutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle to

avoid leaks.

 Remove the plug from the socket when cleaning

the machine and when carrying out maintenance

work.

Cleaning the dishwasher

 The external surfaces of the machine and the

control panel may be cleaned using a cloth

dampened with warm soapy water. Do not use

solvents or abrasive products.

 Any marks on the appliance interior may be

removed using a cloth dampened with water and

a little vinegar.

Preventing unpleasant odours

 Always keep the door of the appliance ajar in

order to avoid moisture from forming and being

trapped inside the machine.

 Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This

will avoid food becoming trapped in the seals,

which is the main cause of the formation of

unpleasant odours.

Cleaning the sprayer arms

Food residue may become

encrusted onto the sprayer

arms and block the holes

used to spray the water. It

is therefore recommended

that the arms are checked

from time to time and

cleaned with a small non-

metallic brush.

Cleaning the filters

The filters remove food residue from the water used

in the wash cycle: to obtain the best results from

each wash, they should be cleaned.

Clean the filters regularly.

After cleaning check that the filter assembly has

been replaced correctly.

The dishwasher should not be used without filters

or when the filter is loose..

1. Remove the filters by pulling the handle upwards.

2. Clean the filters:

 after every wash

cycle, remove the

largest pieces of

residue from

semicircular plate A

and glass B (these

may be removed by

pulling the handle) by

rinsing them under

running water.

 The entire filter

assembly should be

cleaned thoroughly

once a month: this

includes the

semicircular plate A,

the glass B and the

cylinder C (this may be

removed by turning it

in an anti-clockwise direction). Use a small non-

metallic brush to clean these parts.

3. Reconstruct the filter assembly and replace it in

the correct position, following movements 1 and 2 as

shown in the figure, until it clicks into place.

Leaving the machine unused for

extended periods

 Disconnect the appliance from the electricity

supply and shut off the water tap.

 Leave the door of the appliance ajar.

 When you return, run a wash cycle when the

dishwasher is empty.

Care and maintenance

22

EN

The appliance was designed and manufactured

in compliance with current international safety

standards. The following information has been

provided for safety reasons and should therefore be

read carefully.

General safety

 The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

 The appliance must be used by adults only, to

wash domestic crockery according to the

instructions in this manual.

 The appliance must not be installed outdoors,

even in covered areas. It is extremely dangerous

to leave the machine exposed to rain and storms.

 Do not touch the appliance when barefoot.

 When unplugging the appliance always pull the

plug from the mains socket, do not pull on the

cable.

 The water supply tap must be shut off and the

plug should be removed from the electrical

socket before cleaning the appliance or carrying

out any maintenance work.

 If the appliance breaks down, do not under any

circumstances touch the internal parts in an

attempt to carry out the repair work yourself.

 Never touch the heating element.

 Do not lean or sit on the open door of the

appliance: this may cause the appliance to

overturn.

 The door should not be left open as it may create

a dangerous obstacle.

 Keep detergent and rinse aid out of reach of

children.

 The packaging material should not be used as a

toy: it can become a choking or suffocation

hazard.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE),

requires that old household electrical appliances

must not be disposed of in the normal unsorted

municipal waste stream. Old appliances must be

collected separately in order to optimise the

recovery and recycling of the materials they contain

and reduce the impact on human health and the

environment. The crossed out "wheeled bin" symbol

on the product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Saving water and energy

 Only start a wash cycle when the dishwasher is

full. While waiting for the dishwasher to be filled,

prevent unpleasant odours with the Soak cycle

(see Wash Cycles).

 Select a wash cycle that is suited to the type of

crockery and to the soil level of the crockery

using the Wash cycle table:

- for dishes with a normal soil level, use the Eco

wash cycle, which guarantees low energy and

water consumption levels.

- if the load is smaller than usual activate the Half

load option

* (see Start-up and use).

 If your electricity supply contract gives details of

electricity saving time bands, run wash cycles

during the periods when a lower tariff is applied.

The Delayed start

* button (see Start-up and use)

helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

 We strongly recommend that you use detergents

that do not contain phosphates or chlorine, as

these products are harmful to the environment.

 Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result

detergents containing enzymes can be used in

conjunction with low-temperature wash cycles in

order to achieve the same results as a normal

65°C wash cycle.

 To avoid wasting detergent, use the product in

appropriate quantities based on the

manufacturers recommendations, the hardness

of the water and the soil level and quantity of the

crockery. Even if they are biodegradable,

detergents contain substances that may alter the

balance of nature.

* Only available in selected models.

Precautions and advice

23

EN

Whenever the appliance fails to work, check for a solution from the following list before calling for Technical

Assistance Centre.

Troubleshooting

Problem: Possible causes / Solutions:

The dishwasher does not start.

• The plug has not been inserted into the electrical socket properly, or

there is no power in the house.

• The dishwasher door has not been shut properly.

• A delayed start has been programmed (see Start-up and use).

No water drains out from

the dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues (see Care and maintenance).

The dishwasher makes

excessive noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has

not been measured out correctly or it is not suitable for use in

dishwashers (see Start-up and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to

the hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

• The crockery is made from non-stick material.

The dishes and glasses are

streaked or have a bluish

tinge.

• The rinse aid dosage is too high (see Rinse aid and salt).

The crockery has not been

dried properly.

• The rinse aid has been used up or the dosage is too low (see Rinse aid

and salt).

• The rinse aid dispenser setting is not high enough.

• A wash cycle without a drying programme has been selected.

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has

not been measured out correctly or it is not suitable for use in

dishwashers (see Start-up and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not

take any water in/Tap shut-

off alarm.

(several short beeps are emitted)*

Only available in selected models.

(the Soak and Rapid Wash Cycle

indicator lights flash).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken

when the beeps sounded.* Switch off the machine using the ON/OFF

button, turn on the tap and switch the machine back on after 20

seconds by pressing the same button. Re-programme the machine and

restart the wash cycle.

Foam/Blocked filter alarm

(the Soak and Eco wash Cycle

indicator lights flash).

• Switch off the appliance by pressing the ON/OFF button.

• There is an excess of foam inside the machine.

• A detergent which is not suitable for use in the dishwasher has been

used;

• The lid on the rinse aid compartment has not been shut correctly.

• Remove any food residues from the filters (see Care and maintenance).

Replace the filter assembly correctly and switch the machine back on

by pressing the ON/OFF button. Re-programme the machine and restart

the wash cycle.

Water intake solenoid

valve malfunction alarm

(the Rapid Wash Cycle indicator

light flash).

• Switch off the appliance by pressing the ON/OFF button and switch it

back on after a minute. If the alarm continues, shut off the water tap to

eliminate the risk of flooding, remove the plug from the electrical

socket and contact Assistance.

24

EN

Assistance

Before calling for Assistance:

 Check whether you can solve the problem on

your own (see Troubleshooting);

 Restart the programme to check whether the

problem has been solved;

 If this is not the case, contact an authorised

Technical Assistance Centre on the telephone

number provided on the guarantee certificate.

Always request the assistance of authorised

servicemen.

Notify the operator of:

 the type of problem.

 the appliance model (Mod.).

 the serial number (S/N).

This information can be found on the data plate

situated on the internal edge of the stainless steel

door (see Description of the appliance).

Page is loading ...

47

,-

Sollten Betriebsstörungen auftreten, kontrollieren Sie bitte die nachfolgenden Punkte, bevor Sie sich an den Kundendienst wenden

(siehe Kundendienst).

Einige Störungen werden auf dem Display durch Codenummern-Blinklichtanzeigen gemeldet. Notieren Sie sich diese Anzeigen,

bevor Sie den Kundendienst anfordern.

Störungen und Abhilfe

Störungen: Mögliche Ursachen / Lösungen:

Der Geschirrspü ler startet

nicht.

• Der Netzstecker steckt nicht fest genug in der Steckdose, oder es besteht

ein Stromausfall.

• Die Gerä tetü r ist nicht ganz geschlossen.

• Es wurde eine Startzeitvorwahl programmiert (

siehe Start und

Inbetriebnahme

).

Der Geschirrspü ler pumpt das

Wasser nicht ab.

• Das Spü lprogramm ist noch nicht ganz abgelaufen.

• Der Ablaufschlauch ist geknickt (

siehe Installation

).

• Der Ablauf des Spü lbeckens ist verstopft.

• Im Filtersieb haben sich Speisereste angesammelt (

siehe

Wartung und

Pflege

).

Der Geschirrspü ler ist zu laut. • Das Geschirr schlä gt aneinander oder gegen die Sprü harme.

Auf dem Geschirr und auf den

Glä sern befinden sich

Kalkablagerungen oder ein

weiß er Belag.

• Es fehlt Regeneriersalz bzw. die Dosierung entspricht nicht der

Wasserhä rte (

siehe Klarspüler und Regeneriersalz

).

• Der Deckel des Salzbehä lters ist nicht ordnungsgemäß geschlossen.

• Es fehlt Klarspü lmittel oder es wird unzureichend dosiert.

• Das Geschirr besteht aus Antihaftmaterial.

Das Geschirr und die Glä ser

weisen weiß e Streifen bzw.

blä uliche Schattierungen auf.

• Die Dosierung des Klarspü lers ist zu hoch (

siehe Klarspüler und

Regeneriersalz

).

Das Geschirr ist nicht ganz

trocken.

• Es fehlt Klarspü lmittel oder es wird unzureichend dosiert (

siehe Klarspüler

und Regeneriersalz

).

• Die Klarspü ler-Dosiereinstellung ist nicht angemessen.

• Es wurde ein Spü lprogramm, das keinen Trockengang vorsieht, eingestellt.

Das Geschirr ist nicht sauber

geworden

• Die Kö rbe wurden zu voll geladen (

siehe Beschickung der Körbe

).

• Das Geschirr wurde nicht korrekt eingerä umt.

• Die Sprü harme kö nnen sich nicht frei bewegen.

• Das Spü lprogramm ist zu schwach (

siehe Spülprogramme

).

• Es hat sich zu viel Schaum gebildet: Das Spü lmittel wurde unkorrekt

dosiert oder es ist ungeeignet für Geschirrspü ler (

siehe Start und

Inbetriebnahme

).

• Der Stö psel des Klarspü lerbehä lters wurde nicht korrekt geschlossen.

• Das Filtersieb ist schmutzig oder verstopft (

siehe Wartung und Pflege

).

• Es fehlt Regeneriersalz (

siehe Klarspüler und Regeneriersalz

).

Der Geschirrspü ler lä dt kein

Wasser/Alarm Wasserhahn

geschlossen.

(Sie vernehmen kurze Signaltöne)

Nur an einigen Modellen.

(Es blinken die 2. und 3.

PROGRAMM-Anzeigeleuchte von

rechts.

Einweichen - Kurz)

• Es besteht eine Unterbrechung der Wasserzufuhr.

• Der Zufuhrschlauch ist geknickt (

siehe Installation

).

• Ö ffnen Sie den Wasserhahn; das Gerä t setzt sich nach wenigen Minuten in

Gang.

• Das Gerä t hat auf Sperre geschaltet, weil nach Erklingen der Bip-Tö ne*

kein Eingriff erfolgte. Schalten Sie das Gerä t ü ber die ON/OFF-Taste aus,

ö ffnen Sie den Wasserhahn und schalten Sie das Gerä t nach 20 Sekunden

ü ber dieselbe Taste wieder ein. Wiederholen Sie die Gerä teeinstellung und

starten Sie das Spü lprogramm erneut.

Alarmanzeige

Schaum/Filtersiebe verstopft

(Es blinken die 2. und 4.

PROGRAMM-Anzeigeleuchte von

rechts. Einweichen -

Umweltfreundliches Sparprogramm)

• Schalten Sie das Gerä t ü ber die ON/OFF-Taste aus.

• Es befindet sich zu viel Schaum in dem Gerä t.

• Es wurde ein fü r Geschirrspü ler ungeeignetes Spü lmittel verwendet.

• Der Stö psel des Klarspü lerbehä lters wurde nicht korrekt geschlossen.

• Befreien Sie die Filtersiebe von Speiseresten (

siehe

Wartung und Pflege

).

Setzen Sie die Filtersiebeinheit wieder ordnungsgemäß ein und schalten

Sie das Gerä t ü ber die ON/OFF-Taste erneut ein. Wiederholen Sie die

Gerä teeinstellung und starten Sie das Spü lprogramm erneut.

Alarmanzeige aufgrund einer

Stö rung des

Wasserversorgungs-

Magnetventils

(Es blinkt die 3. PROGRAMM-

Anzeigeleuchte von rechts. Kurz)

• Schalten Sie das Gerä t durch Drü cken der ON/OFF-Taste aus und schalten

Sie es nach einer Minute wieder ein. Besteht der Alarm weiterhin, drehen

Sie den Wasserhahn zu, um Ü berschwemmungen zu vermeiden. Ziehen Sie

daraufhin den Netzstecker aus der Steckdose und fordern Sie den

Kundendienst an.

Page is loading ...

#'

NL

Als er storingen zijn in de werking van het apparaat dient u eerst de volgende punten na te gaan voor u zich tot de Service

Dienst wendt (zie Service).

Storingen en oplossingen

Storingen: Mogelijke oorzaken / Oplossingen:

De afwasautomaat start niet.

• De stekker zit niet goed in het stopcontact of het hele huis zit

zonder stroom.

• De deur van de afwasautomaat is niet goed dicht.

• U heeft een Uitgestelde start ingesteld (zie Starten en gebruik).

De afwasautomaat pompt het

water niet af.

• Het programma is nog niet beë indigd.

• De waterafvoerbuis is gebogen (zie Installatie).

• De afvoer van de wasbak is verstopt.

• Het filter is verstopt met etensresten (zie onderhoud en

verzorging)

De afwasautomaat maakt

lawaai.

• De vaat stoot tegen elkaar of tegen de sproeiarmen.

Er blijven op vaat en glazen

kalkafzettingen of een witte

aanslag achter.

• Er zit niet genoeg onthardingszout in het reservoir of zijn

afregeling is niet toereikend voor de waterhardheid (zie

Glansmiddel en onthardingszout).

• De dop van het zoutreservoir is niet goed dicht.

• Het glansmiddel is op of de dosering is ontoereikend.

• Het vaatwerk is voorzien van een antiaanbaklaag.

Er blijven op vaat en glazen

strepen of blauwe kringen

achter.

• Er wordt teveel glansmiddel gebruikt (zie Glansmiddel en

onthardingszout).

De vaat is niet droog

genoeg.

• Het glansmiddel is op of de dosering is ontoereikend (zie

Glansmiddel en onthardingszout).

• De regeling van het glansmiddel is niet correct.

• U heeft een programma zonder drogen ingesteld.

De vaat is niet schoon.

• De rekken zijn te vol geladen (zie Het laden van de rekken).

• De vaat is niet goed verdeeld.

• De sproeiarmen kunnen niet vrijuit draaien.

• Het wasprogramma is niet energiek genoeg (zie Programma’s).

• Overtollig schuim: het wasmiddel is niet goed gedoseerd of is

niet geschikt voor de afwasautomaat (zie Starten en gebruik).

• Het deksel van het zoutreservoir is niet goed afgesloten.

• Het filter is vuil of verstopt (zie Onderhoud en verzorging).

• Er zit geen onthardingszout meer in het reservoir (zie

Glansmiddel en onthardingszout).

De afwasautomaat vult zich

niet met water/Alarm kraan

dicht.

(u hoort enkele korte pieptonen)*

Alleen aanwezig op bepaalde

modellen.

(de tweede en derde PROGRAMMA

controlelampjes van rechts

knipperen. Inweken - Snel ).

• Er zit geen water in de centrale waterleiding.

• De watertoevoerbuis is gebogen (zie Installatie).

• Open de kraan en de machine start na enkele minuten vanzelf.

• Het apparaat is geblokkeerd omdat u niet heeft ingegrepen na

de pieptonen*. Schakel de machine uit met de ON/OFF toets,

open de kraan en schakel hem na 20 seconden opnieuw in door

middel van dezelfde toets. Herprogrammeer het apparaat en

start het opnieuw.

Alarm Schuim/ filters

verstopt

(de tweede en vierde

PROGRAMMA controlelampjes van

rechts knipperen. Inweken - Eco).

• Schakel het apparaat uit door op de ON/OFF toets te drukken.

• Overtollig schuim aanwezig in het apparaat.

• U heeft een afwasmiddel gebruikt dat niet geschikt is voor de

afwasautomaat;

• Het deksel van het zoutreservoir is niet goed afgesloten.

• Reinig het filter van de eventuele etensresten (zie Onderhoud

en verzorging). Doe de filtergroep weer op zijn plaats en

schakel het apparaat in door op de ON/OFF toets te drukken.

Herprogrammeer het apparaat en start het opnieuw.

Alarm storing aan de

elektromagnetische klep van

de watertoevoer

(het derde PROGRAMMA

controlelampje van rechts knippert.

Snel).

• Schakel het apparaat uit door te drukken op de toets ON/OFF

en schakel het na een minuut weer in. Als het alarm blijft gaan

moet u de waterkraan dichtdraaien om lekkages te vermijden,

vervolgens de stekker uit het stopcontact halen en de

Servicedienst inschakelen.

Page is loading ...

Whirlpool LL 42 User guide

This manual is also suitable for

Whirlpool LL 42 User guide

in other languages