RK5

RK6T2

RK8T2

Voyager

®

Series Weatherproof Rock Speakers

2

Specifications Voyager RK5 Voyager RK6T2 Voyager RK8T2

Frequency Response 70 – 20K Hz, ±3dB 60 – 20K Hz, ±3dB 50 – 20K Hz, ±3dB

Recommended Amp Power 5 – 100 Watts 10 – 150 Watts 20 – 200 Watts

Overall Dimensions (WxHxD) 12

⁄5” x 11

1

⁄5” 18

1

⁄2” x 14

4

⁄5” x 13

2

⁄5”

Weight 9 lbs 12.5 lbs 16 lbs

Description

Thank you for purchasing the Boston Acoustics Voyager

®

system. These speakers combine the famous Boston sound, weatherproof design and enclosures designed

to blend into the surrounding environment. Enjoy exceptional sound on your patio, in your garden or around

your pool.

All the Voyager Rock models are true two-way designs housed in rugged enclosures with a natural stone appear-

concept and also uses a pair of 1-inch soft dome tweeters and matches them with a potent 8-inch woofer.

All the parts of the Voyager

RK series speakers are manufactured from high-tech plastics, rubbers, and other

materials that have been extensively tested for durability.

Additional Key Features

• The Voyager RK speakers are “voiced” for outdoor performance. Their sound is contoured to provide the

best performance in open air environments. They blend perfectly with the other Voyager series models.

• The woofers have mica-filled copolymer cones with butyl rubber surrounds. The tweeters have soft domes.

• The woofers have a stepped woofer basket that sets the cone forward to prevent “tunnel effect” and pre-

serve smooth, natural midrange sound.

audio systems where many speakers are used or where speaker wires must be run over long distances.

3

Speaker Placement

The placement of outdoor speakers follow a different set of priorities from those used for indoor speakers.

Speakers used indoors in music or AV systems are placed to achieve the best possible stereo or surround sound

image. You typically listen to them from a certain location while enjoying music or AV programs. But outdoor

listening is usually part of more active forms of recreation. So considerations such as stereo imaging or proper

• What are you going to be doing while listening to the speakers? Will you be actually listening to the

speakers or will they be providing background while you’re doing something else?

• How important is traditional stereo imaging? Do you want normal stereo imaging or is good balanced

coverage of all the sound more important?

An outdoor environment places special demands on a speaker system. You do not have the advantage of an

enclosed, defined area. So you must try to place them were they will give you the sound coverage you want, and

be in a good location for sound reproduction.

For example, when selecting outdoor speaker locations, it is usually best to have a solid surface behind the

speaker. Such placement helps reinforce bass output. Bass sound is by nature omni-directional. The bass sound

energy a speaker produces will spread out in all directions. Outdoors, where there are no walls to contain the

This provides good coverage to the area

where the table and chairs are.

Another pair of speakers are placed

against the fence facing the lounge chairs

to provide sound coverage for that area.

In these examples the RK5, being a mono-

only speaker, would have normal stereo

separation. The RK6T2 and RK8T2 could

be wired for mono to produce normal

stereo separation. Or they can be wired

4

Speaker Wires

them.

You must select wire that is suited to outdoor usage. Look for wire that is rated for burial. It will stand up to the

system is recommended. Such systems use a special amplifier that has a “70V” (or in some countries, “100V”)

degradation. Speakers used in a high voltage system require a transformer. An optional transformer is

cover located on the bottom of the speaker where the wires emerge. Contact a custom audio system installer

for more information.

Speaker Connection Polarity

It is important that all the speakers in a system are hooked up with similar polarity or “in phase.” The speaker

terminals on amplifiers are color coded and marked for polarity – typically red is + and black is –. The RK series

models have “pig tail” wire leads that extend from the bottom of the cabinet. The wires are color coded in the

usual way – red is + and black is –. In the case of the RK6T2 and RK8T2 there are two wire leads. The wire lead

for the “right” side has red and black leads. The “left” side wire lead has yellow and black wires. All you have to

do is make each connection the same way. This is particularly important with the RK6T2 and RK8T2. If they are

conected improperly, they will produce almost no sound.

Connecting the Speakers

The “pig tail” leads from the speakers are connected to the speaker wires with the supplied wire nuts that are

5

Basic Stereo Speaker Wiring

wire to be sure that positive goes to positive, and negative goes to negative, at all the connection points.

Wiring the RK6T2 and RK8T2

The RK6T2 and RK8T2 are essentially a pair of stereo speakers in one enclosure. They have two tweeters and a

woofer with a double-wound voice coil. They can be wired to operate as a single speaker or as a “pair” of stereo

speakers. How you use them depends on the physical layout of your area.

Using the example in the speaker placement illustration, you might connect the speakers facing the patio area as

stereo speakers. They are placed so that they will not produce a typical stereo image. Wiring those speakers so

6

good stereo image. Those speakers could be wired so each one reproduces just one channel of a stereo signal.

Multiple Speaker Connections

Sometimes you may want to conect more than one speaker to a given channel of an amplifier. This can be done

with certain limitations. The main concern is that the impedance (or electrical “resistance”) expressed in ohms,

of the combined speaker load must be within a range common amplifiers can handle. The following information

describes basic common multi-speaker connection schemes. For the sake of clarity and space the connection

diagrams will show common schematic symbols instead of speaker images.

There are two basic connection methods-parallel (A) and series (B). The parallel connection is shown on the left,

the series connection on the right.

can handle a 4-ohm impedance load. Impedance loads lower than 4 ohms can trigger amplifer protection circuits

or, in some cases, cause over heating.

Two 8 ohm speakers in series produce a 16 ohm impedance. This is an easy impedance for an amplifer to handle.

However it will result in somwhat lower power ouput.

7

done using a combined series/parallel connection. This type of conection is illustrated below. Two speakers

Listening Levels and Power Handling

The listed power recommendations assume you will operate your system in a way that will not produce

distortion. Even these rugged speakers can be damaged by a modest amplifier if it produces distortion.

If you hear a harsh, gritty noise, turn down the volume. Prolonged or repeated operation of your speaker

with a distorted signal from the amplifier can cause damage that is not covered by the warranty.

8

Limited Warranty

materials and workmanship for a period of 5 years from the date of purchase.

Your responsibilities are to install and use them according to the instructions supplied, to provide safe and se-

ping, or repairs/modifications by anyone other than an authorized Boston Acoustics service representative.

This warranty is limited to the Boston Acoustics product and does not cover damage to any associated equip-

has been removed or defaced. This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

If Service Seems Necessary

First, contact the dealer from whom you purchased the product. If that is not possible, write to:

Boston Acoustics, Inc.

300 Jubilee Drive

Peabody, MA 01960 USA

Or contact us via e-mail at:

[email protected]

We will promptly advise you of what action to take. If it is necessary to return your RK series unit to the fac-

tory, please ship it prepaid. After it has been repaired, we will return it freight prepaid in the United States and

Canada.

household waste. Instead, it may be placed in a separate collection facility for electronic waste or

returned to a retailer when purchasing similar product. The producer paid to recycle this product.

Doing this contributes to reuse and recycling, minimizes adverse effects on the environment and

human health and avoids any fines for incorrect disposal.

®

Boston Acoustics, Inc.

Rich Gorzynski, Project Manager: 978/538-5141

OWNERS MANUAL RK artwork

Date: 05/01/07

BA P/N: 142-002634-0 Scale: 100%

Note:

This drawing and data embody proprietary designs and information which is the confidential property of Boston Acoustics,

None of which shall be copied, reproduced, disclosed to others, proposed or used in whole or in part, for any purpose

without express written permission of a duly authorized agent of Boston Acoustics. This drawing is subject to recall by

Boston Acoustics at any time. It is being submitted in confidence and patent rights are reserved by Boston Acoustics.

All Material must be compliant with the

latest revision of the Boston Acoustics

Environmental Purchasing Specification