Black & Decker GL280 User manual

Brand: Black & Decker

Model: GL280

Category: Grass trimmers

Type: User manual

GL280

GL301

GL315

GL337

GL350

English (Original instructions) 6

Intended use

Your Black & Decker trimmer has been designed for trimming

and nishing lawn edges and to cut grass in conned spaces.

This appliance is intended for consumer use only.

Safety instructions

Warning! When using mains-powered appliances, basic

safety precautions, including the following, should always be

followed to reduce the risk of re, electric shock, personal

injury and material damage.

u Read all of this manual carefully before operating the

appliance.

u The intended use is described in this manual. The use of

any accessory or attachment or the performance of any

operation with this appliance other than those recommended

in this instruction manual may present a risk of personal

injury.

u Retain this manual for future reference.

Using your appliance

Always take care when using the appliance.

u Always use safety glasses or goggles.

u Never allow children or people unfamiliar with the

instructions to use the appliance.

u Do not allow children or animals to come near the work

area or to touch the appliance or power supply cord.

u Close supervision is necessary when the appliance is

used near children.

u This appliance is not intended for use by young or inrm

persons without supervision.

u This appliance is not to be used as a toy.

u Only use the appliance in daylight or good articial light.

u Use in a dry location only. Do not allow the appliance to

become wet.

u Do not immerse the appliance in water.

u Do not open the body casing. There are not user-

serviceable parts inside.

u Do not operate the appliance in explosive atmospheres,

such as in the presence of ammable liquids, gases or

dust.

u To reduce the risk of damage to plugs or cords, never pull

the cable to remove the plug from a socket.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children must be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

After use

u When not in use, the appliance should be stored in a dry,

well ventilated place out of reach of children.

u Children should not have access to stored appliances.

u When the appliance is stored or transported in a vehicle it

should be placed in the boot or restrained to prevent

movement following sudden changes in speed or direction.

Inspection and repairs

u Before use, check the appliance for damaged or defective

parts. Check for breakage of parts and any other

conditions that may affect its operation.

u Do not use the appliance if any part is damaged or defective.

u Have any damaged or defective parts repaired or replaced

by an authorised repair agent.

u Never attempt to remove or replace any parts other than

those specied in this manual.

Using an extension cable

Always use an approved extension cable suitable for the

power input of this appliance (see technical data). The extension

cable must be suitable for outdoor use and marked accordingly.

Up to 30 m of 1.5 mm

HO5VV-F extension cable can be used

without loss of product performance. Before use, inspect the

extension cable for signs of damage, wear and ageing.

Replace the extension cable if damaged or defective.

When using a cable reel, always unwind the cable completely.

Additional safety instructions for grass trimmers

Warning! Cutting elements continue to rotate after the motor

is switched off.

u Be familiar with the controls and the proper use of the

appliance.

u Before use, check the power supply cord and extension

cord for signs of damage, ageing and wear. If a cord

becomes damaged during use, disconnect the cord from

the mains supply immediately. DO NOT TOUCH THE

CORD BEFORE DISCONNECTING THE SUPPLY.

u Do not use the appliance if the cords are damaged or worn.

u Wear stout shoes or boots to protect your feet.

u Wear long trousers to protect your legs.

u Before using the appliance, check that your cutting path is

free from sticks, stones, wire and any other obstacles.

u Only use the appliance in the upright position, with the

cutting line near the ground. Never switch the appliance

on in any other position.

u Move slowly when using the appliance. Be aware that

freshly cut grass is damp and slippery.

u Do not work on steep slopes. Work across the face of

slopes, not up and down.

u Never cross gravel paths or roads while the appliance is

running.

u Never touch the cutting line while the appliance is running.

u Do not put the appliance down until the cutting line has

come to a complete standstill.

u Use only the appropriate type of cutting line.

Never use metal cutting line or shing line.

u Be careful not to touch the line trimming blade.

u Take care to keep the mains cable away from the cutting

line. Always be aware of the position of the cable.

u Keep hands and feet away from the cutting line at all

times, especially when switching on the motor.

u Before using the appliance and after any impact, check for

signs of wear or damage and repair as necessary.

u Never operate the appliance with damaged guards or

without guards in place.

u Take care against injury from any device tted for trimming

the lament line length. After extending new cutter line

always return the machine to its normal operating position

before switching on.

u Always ensure that the ventilation slots are kept clear of

debris.

u Do not use the lawn trimmer (edge trimmer), if the cords

are damaged or worn.

u Keep extension cords away from cutting elements.

Labels on appliance

The following warning symbols are found on the appliance:

Read the manual prior to operation.

Wear safety glasses or goggles when operating this

appliance.

Keep people and animals at least 6 m away from the

cutting area.

Do not expose the appliance to rain or high humidity.

Electrical safety

This appliance is double insulated; therefore no earth

wire is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Handle

3. Cable restraint

4. Power inlet

5. Secondary handle

6. Tube

7. Storage hooks

8. Adjustment button

9. Guard

10. Line trimming blade

11. Cutting line

12. Spool housing

13. Edge guide

14. Head

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Attaching the tube to the head (g. A)

u Align the rectangular tab of the tube (6) with the location in

the head (14).

u Insert the tube into the head and push until it clicks into place.

Attaching the handle to the tube (g. B)

u Align the square tab of the tube (6) with the location in the

handle (2).

u Insert the tube into the handle and push until it clicks into

place.

Fitting the guard (g. C)

u Remove the screw (15) from the head.

u Place the guard onto the tool as shown.

u Firmly press the guard (9) until it snaps into place.

u Secure the guard with the screw.

Warning! Never use the tool unless the guard is properly tted.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

u Remove the tape holding the cutting line (11) to the spool

housing (12).

Connecting the tool to the mains (g. D)

u Connect the female plug of a suitable extension cable to

the power inlet (4).

u Loop the cable through the cable restraint (3).

u Insert the mains plug into a mains outlet.

For wired in cable units: Make sure the cable is looped through

the cable restraint prior to connecting the plug to the mains

outlet.

Warning! The extension cable must be suitable for outdoor

use.

Use

Warning! Let the tool work at its own pace. Do not overload.

Setting the tool to trimming or edging mode

(g. E - G)

The tool can be used in trimming mode as shown in g. F or in

edging mode to trim overhanging grass along lawn edges and

ower beds as shown in g. G.

Trimming mode (g. E & F)

For trimming, the trimmer head should be in the position

shown in g. F. If it is not:

u Depress the adjustment button (8).

u Rotate the head (14), while releasing the button.

u When the head is in position, the button will lock into place.

Note: The tube will only rotate in one direction.

Edging mode (g. E & G)

For edging, the trimmer head should be in the position shown

in g. G. If it is not:

u Depress the adjustment button (8).

u Rotate the head (14), while releasing the button.

u When the head is in position, the button will lock into place.

Note: The tube will only rotate in one direction.

Switching on and off

u To switch the tool on, squeeze the trigger lever (1).

u To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on

position.

Hints for optimum use

General

u In order to achieve optimum cutting results, only cut dry

grass.

Trimming

u Hold the tool as shown in g. F.

u Gently swing the trimmer from side to side.

u When cutting long grass, work in stages from the top.

Take small cuts.

u Keep the tool away from hard objects and delicate plants.

u If the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than

50 mm.

u Do not use the tool to create edges. To create edges,

use an edging spade.

u Guide the tool as shown in g. G.

u To make a closer cut, slightly tilt the tool.

Fitting a new spool of cutting line (g. H - J)

Spool with single cutting line (g. H)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6481).

u Keep the tabs (16) depressed and remove the spool cover

(17) from the housing (12).

u Remove the empty spool (18) from the spool housing.

u Remove any dirt and grass from the spool cover and housing.

u Take the new spool and unwind approximately 9 cm of

cutting line.

u Feed the cutting line through the eyelet (19).

u Push the spool onto the drive shaft (20) and rotate it

slightly until it is seated. Make sure that the cutting line is

not trapped under the spool and that 9 cm of cutting line

protrudes from the housing.

u Align the tabs on the spool cover with the holes in the

housing.

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting line protrudes beyond the trimming

blade (10), cut it off so that they just reach the blade.

Spool with twin cutting line (g. I & J)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6441). Complete cassettes

containing a spool of cutting line are also available

(cat. no. A6488).

u Keep the tabs (21) depressed and remove the spool cover

(22) from the housing (12).

u Remove the empty spool (23) from the spool cover.

u Remove any dirt and grass from the spool cover and

housing.

u Take the new spool and push it onto the boss in the spool

cover. Rotate the spool slightly until it is seated.

u Unclip the end of one of the cutting lines and feed the line

into one of the eyelets (24). The line should protrude

approximately 9 cm from the spool cover.

u Unclip the end of the other cutting line and feed the line

into the other eyelet. The line should protrude

approximately 9 cm from the spool cover.

u Align the tabs (21) on the spool cover with the cut-outs (25)

in the housing.

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (10), cut them off so that they just reach the blade.

Winding a new cutting line onto an empty spool

(g. K - O)

You may wind new cutting line onto an empty spool.

Spool with single cutting line (g. K & L)

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).

u Remove the empty spool from the tool as described above.

u Remove any remaining cutting line from the spool.

u Feed 2 cm of cutting line into one of the holes (26) in the

spool as shown.

u Bend the cutting line and anchor it in the L-shaped slot (27).

u Wind the cutting line onto the spool in the direction of the

arrow (28). Make sure to wind the line on neatly and in

layers. Do not criss-cross.

u When the wound cutting line reaches the recesses (29),

cut the line. Let the line protrude approximately 9 cm from

the spool and hold a nger on the line to keep it in place.

u Proceed as described above to t the spool on the tool.

Warning! Only use the appropriate type of Black & Decker

cutting line.

Spool with twin cutting line (g. M - O)

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6440).

u Remove the empty spool from the tool as described above.

u Remove any remaining cutting line from the spool.

u First wind new line onto the uppermost part of the spool:

- Feed 2 cm of cutting line into one of the slots (30) in the

upper section of the spool as shown.

- Wind the cutting line onto the spool in the direction of

the arrow (31). Make sure to wind the line on neatly

and in layers. Do not criss-cross.

- When the wound cutting line reaches the recesses (32),

cut the line.

- Temporarily park the line in the slots (33) on one side of

the spool as shown.

u Repeat the above procedure for the second cutting line on

the lower section of the spool. Park the line in the unused

slots (33).

u Proceed as described above to t the spool on the tool.

Do not forget to release the cutting line from the parking

slots (33).

Warning! Only use the appropriate type of Black & Decker

cutting line. Ensure that cutting line is present in both sections

of the spool.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local Black & Decker repair agent.

Warning! Before proceeding, unplug the tool.

Appliance runs slowly

u Check that the spool housing can rotate freely. Carefully

clean it if necessary.

u Check that the cutting line does not protrude more than

11 cm from the spool housing. If it does, cut it off so that it

just reaches the line trimming blade.

Automatic line feed does not work

u Keep the tabs depressed and remove the spool cover

from the housing.

u Pull the cutting line until it protrudes 11 cm from the

housing. If insufcient cutting line is left on the spool,

install a new spool of cutting line as instructed above.

u Align the tabs on the spool cover with the cut outs in the

housing.

u Push the cover onto the housing until it snaps securely

into place.

u If the cutting line protrudes beyond the trimming blade,

cut it off so that it just reaches the blade.

If the automatic line feed still does not work or the spool is

jammed, try the following suggestions:

u Carefully clean the spool cover and housing.

u Remove the spool and check if the lever can move freely.

u Remove the spool and unwind the cutting line, then wind it

on neatly again as described above. Replace the spool as

instructed.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool/appliance care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Technical data

GL280 GL301 GL315

TYPE 2 TYPE 2 TYPE 3

Input voltage V

230 230 230

Power input W 300 300 320

No-load speed min

-1

10,000 10,000 10,000

Weight kg 2.2 2.2 2.2

GL337 GL350

TYPE 2 TYPE 3

Input voltage V

230 230

Power input W 320 350

No-load speed min

-1

10,000 10,000

Weight kg 2.2 2.2

Hand/arm weighted vibration value according to EN 786:

= 4 m/s

, uncertainty (K) = 1.5 m/s

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

GL280/GL301/GL315/GL337/GL350

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1, EN 60335-2-91

2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII

KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem,

The Netherlands

Notied Body ID No.: 0344

Level of accoustic power according to 2000/14/EC

(Article 12, Annex III, L ≤ 50 cm):

(measure sound power) 95 dB(A)

uncertainty (K) = 3 dB(A)

(guaranteed sound power) 96 dB(A)

uncertainty (K) = 3 dB(A)

These products also comply with directive 2004/108/EC.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

01-10-2009

UK patent application no.: 059745.6

European Community design application nos. 340385-0001 &

339544-0001

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within

24 months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

ensure minimum inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker ofce at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

date on new products and special offers. Further information

on the Black & Decker brand and our range of products is

available at www.blackanddecker.co.uk

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

code to Black & Decker in your country.

90553705 REV-0 03/2010

Australia

Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100

20 Fletcher Road, Mooroolbark, Fax 03-9727 5940

Victoria, 3138

New Zealand

Black & Decker Tel. +64 9 259 1133

5 Te Apunga Place Fax +64 9 259 1122

Mt Wellington

Auckland 1060

United Kingdom

Black & Decker Tel. 01753 511234

210 Bath Road Fax 01753 551155

Slough, Berkshire SL1 3YD Helpline 01753 574277

Black & Decker GL280 User manual

Brand: Black & Decker

Model: GL280

Category: Grass trimmers

Type: User manual

Download PDF

report

Black & Decker GL280 User manual

Black & Decker GL280 User manual

Related papers

Other documents