Cisco 3600 User manual

1

Cisco IOS Release 12.1(5)T

V.110 Support for Cisco 3600 Series Digital

Modems

This feature implements the V.110 protocol on Cisco digital modem network modules (NM-6DM,

NM-12DM, NM-18DM, NM-24DM, and NM-30DM) for the Cisco 3600 series of routers, and provides

V.110 support for digital modems connected over BRI or PRI interfaces.

This document contains the following sections:

• Feature Overview, page 1

• Supported Platforms, page 2

• Supported Standards, MIBs, and RFCs, page 2

• Command Reference, page 4

• Glossary, page 24

Feature Overview

V.110 is a real-time method of encapsulating varying data rates and the associated RS-232 signals into

a 64-Kbps ISDN B-channel. Using this procedure, asynchronous data rates from 600 bps to 38.4 Kpbs

can be transparently rate-adapted over a single 64-Kbps channel.

V.110 is useful for transporting data over GSM-type mobile phones. V.110 over ISDN support is being

added to the MARS platform to support digital modems in many countries which use E1 with ISDN.

V.110, as an alternative to V.120, is a method of ISDN rate adaption. It provides DTEs with V-series

type interfaces with access to ISDN networks by bit stuffing. Many V.110 devices are used in Europe

and Japan.

Benefits

The V.110 recommendation of the ITU-T rate adapts a low-speed connection to an ISDN B-channel,

allowing the remote station or terminal adapter to use the fast call-setup times offered by ISDN. This

feature enables Global System for Communications (GSM) wireless connectivity.

V.110 Support for Cisco 3600 Series Digital Modems

Supported Platforms

2

Cisco IOS Release 12.1(5)T

Restrictions

• The BRI interface with V.110 is not supported by the Cisco 3620 router.

• Cisco 3600 series routers require Low Layer Compatability (LLC) information from the Telco

switch.

Related Documents

• Cisco IOS Dial Services Configuration Guide:Terminal Services , Release 12.1

• Cisco IOS Dial Services Command Reference , Release 12.1

Supported Platforms

The following platforms are supported:

• Cisco 3620

• Cisco 3640

• Cisco 3660

The following network modules (NM) support V.110:

• NM-6DM

• NM-12DM

• NM-18DM

• NM-24DM

• NM-30DM

Supported Standards, MIBs, and RFCs

Standards

ITU-T Recommendation V.110

MIBs

No new or modified MIBs are supported by this feature.

To obtain lists of MIBs supported by platform and Cisco IOS release and to download MIB modules,

go to the Cisco MIB web site on Cisco Connection Online (CCO) at

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.

RFCs

No new or modified RFCs are supported by this feature.

V.110 Support for Cisco 3600 Series Digital Modems

Configuration Tasks

3

Cisco IOS Release 12.1(5)T

Configuration Tasks

There are no configuration tasks. All commands in this feature are existing show modem commands

with modified display output.

Note Cisco 3600 series routers require Low Layer Compatability (LLC) information from the

Telco switch. If you have problems setting up your connection, verify that the Telco switch

supports LLC.

V.110 Support for Cisco 3600 Series Digital Modems

Command Reference

4

Cisco IOS Release 12.1(5)T

Command Reference

No new commands were added for this feature. However, the output for the following commands was

modified to include V.110 information. All other commands used with this feature are documented in

the Cisco IOS Release 12.1 command reference publications.

• show modem

• show modem log

• show modem configuration

• show modem connect-speeds

• show modem operational-status

V.110 Support for Cisco 3600 Series Digital Modems

show modem

5

Cisco IOS Release 12.1(5)T

show modem

To display a high-level performance report for all modems or a single modem, use the show modem

EXEC command.

show modem [slot/port | group number]

Syntax Description

Defaults There are no default behaviors or values for this command.

Command Modes EXEC

Command History

Examples

Router# show modem

Codes:

* - Modem has an active call

R - Modem is being Reset

D - Download in progress

B - Modem is marked bad and cannot be used for taking calls

b - Modem is either busied out or shut-down

Avg Hold Inc calls Out calls Busied Failed No Succ

Mdm Time Succ Fail Succ Fail Out Dial Answer Pct.

* 0/0 00:21:01 132 0 0 0 0 0 0 100%

* 0/1 2d01h 1 0 0 0 0 0 0 100%

0/2 00:00:34 130 0 0 0 0 0 0 100%

* 0/3 00:21:53 126 1 0 0 0 0 0 99%

* 0/4 2d01h 1 0 0 0 0 0 0 100%

0/5 00:00:33 131 0 0 0 0 0 0 100%

* 0/6 00:21:12 131 0 0 0 0 0 0 100%

0/7 00:00:34 131 0 0 0 0 0 0 100%

b 0/8 00:00:00 0 0 0 0 0 0 0 0%

b 0/9 00:00:00 0 0 0 0 0 0 0 0%

!.

b 0/29 00:00:00 0 0 0 0 0 0 0 0%

Total: 00:18:25 783 1 0 0 0 0 0 99%

slot/port (Optional) Specifies the location of a slot and modem port. Remember to

include the forward slash (/) when entering this variable.

group number (Optional) Specifies a modem group to which a specified modem belongs.

The group number range is 1 to 200.

Release Modification

11.2 This command was introduced.

12.1(5)T This command was modified to show the output display indicating V.110

support on Cisco 3600 series platforms.

V.110 Support for Cisco 3600 Series Digital Modems

show modem

6

Cisco IOS Release 12.1(5)T

The following display shows output information for the show modem command:

Router# show modem

Inc calls Out calls Busied Failed No Succ

Mdm Usage Succ Fail Succ Fail Out Dial Answer Pct.

* 1/0 17% 74 3 0 0 0 0 0 96%

* 1/1 15% 80 4 0 0 0 1 1 95%

* 1/2 15% 82 0 0 0 0 0 0 100%

1/3 21% 62 1 0 0 0 0 0 98%

1/4 21% 49 5 0 0 0 0 0 90%

* 1/5 18% 65 3 0 0 0 0 0 95%

* 1/6 19% 58 2 0 0 0 0 0 96%

* 1/7 17% 67 5 0 0 0 1 1 93%

* 1/8 20% 68 3 0 0 0 0 0 95%

1/9 16% 67 2 0 0 0 0 0 97%

1/10 18% 56 2 0 0 0 1 1 96%

* 1/11 15% 76 3 0 0 0 0 0 96%

* 1/12 16% 62 1 0 0 0 0 0 98%

1/13 17% 51 4 0 0 0 0 0 92%

1/14 16% 51 5 0 0 0 0 0 91%

1/15 17% 65 0 0 0 0 0 0 100%

1/16 15% 73 3 0 0 0 0 0 96%

1/17 17% 67 2 0 0 0 0 0 97%

1/18 17% 61 2 0 0 0 0 0 96%

* 1/19 17% 74 2 0 0 0 0 0 97%

1/20 16% 65 1 0 0 0 0 0 98%

* 1/21 16% 58 3 0 0 0 0 0 95%

* 1/22 18% 56 4 0 0 0 0 0 93%

* 1/23 20% 60 4 0 0 0 0 0 93%

Table 1 describes the fields shown in the previous displays of the show modem command.

Ta b l e 1 s h o w m o d e m Field Descriptions

Field Description

Mdm Slot and modem port number. Also, the following modem states can appear

to the left of a slot/modem port number:

• b—Modem was removed from service with the modem shutdown

command or the modem busyout command.

• B—Modem is suspected to be inoperable or bad. No calls can be made

with this modem. The letter B can also mean that a modem firmware

download failed for the specified modem. In this case, try unmarking

the modem as bad with the no modem bad command and upgrading the

modem firmware.

• d—The RAM-based DSP code, which supports K56flex, is not

configured. The modem will revert to transmitting at 33.6 kbps.

• D—Modem is currently downloading firmware.

• p—Firmware download is pending, typically because one or more

modems is active.

• R—Modem is held and isolated in a suspended state by the modem

hold-reset command.

• T—Modem is conducting a back-to-back test with another modem.

• *—Modem is connected or dialing.

Usage Percentage of the total system uptime that all modems are in use.

V.110 Support for Cisco 3600 Series Digital Modems

show modem

7

Cisco IOS Release 12.1(5)T

The following example shows the statistics and current configurations for the manageable modem 2/10.

A dash (-) indicates a field that is not available on basic modems. An x indicates a field that is available

and active on manageable modems. See Table 2 for a description of the fields displayed by the show

modem command.

Router> show modem 2/10

Mdm Typ Status Tx/Rx G Duration TX RX RTS CTS DSR DCD DTR

2/10 V34 Idle 33600/33600 1 00:00:00 x x x x

Modem 2/10, Microcom MNP10 V34 Modem (Select), Async35, TTY35

Firmware (Boot) Rev: 2.1(9) (1.0(5))

Modem config: Incoming and Outgoing

Protocol: reliable/MNP, Compression: V42bis

Management port config: Status polling and AT session

Management port status: Status polling and AT session

TX signals: 0 dBm, RX signals: 0 dBm

Last clearing of "show modem" counters never

0 incoming completes, 0 incoming failures

0 outgoing completes, 0 outgoing failures

0 failed dial attempts, 0 ring no answers, 0 busied outs

0 no dial tones, 0 dial timeouts, 0 watchdog timeouts

0 no carriers, 0 link failures, 0 resets 0 recover oob

0 protocol timeouts, 0 protocol errors, 0 lost events

Connection Speeds 75 300 600 1200 2400 4800

# of connections 0 0 0 0 0 0

Connection Speeds 7200 9600 12000 14400 16800 19200

# of connections 0 0 0 0 0 0

Connection Speeds 21600 24000 26400 28800 31200 33600

# of connections 0 0 0 0 0 1

The following is an output example for a basic V.34 modem module:

Inc calls Number of incoming calls that successfully and unsuccessfully connected

to a modem.

Out calls Number of outgoing calls that successfully and unsuccessfully dialed out

from an available modem.

Busied Out Number of modems that have been manually removed from service.

Failed Dial Number of modems that attempted to dial into the network but failed to

make a connection.

No Answer Number of modems that detected an incoming ring but failed to answer the

call.

Succ Pct. Successful connection percentage of total available modems.

Field Description

V.110 Support for Cisco 3600 Series Digital Modems

show modem

8

Cisco IOS Release 12.1(5)T

Note Unavailable fields are marked with dashes (-).

Router# show modem 1/1

Mdm Typ Status Tx/Rx G Duration TX RX RTS CTS DSR DCD DTR

1/1 - Idle 19200/19200 0 00:01:05 - - - - - - -

Modem 1/1, AS5200 Non-Manageable Modem

Firmware (Boot) Rev: Unknown

Modem config: Unknown

Management config: Not Manageable Modem

Last clearing of "show modem" counters never

- incoming completes, - incoming failures

- outgoing completes, - outgoing failures,

0 failed dial attempts, 0 ring no answers, 0 busied outs

0 no dial tones, 0 dial timeouts, 0 watchdog timeouts

- no carriers, - link failures, 0 resets

- protocol timeouts, - protocol errors, - lost events

Connection Speeds 75 300 600 1200 2400 4800

# of connections 0 0 0 0 0 0

Connection Speeds 7200 9600 12000 14400 16800 19200

# of connections 0 0 0 0 0 0

Connection Speeds 21600 24000 26400 28800 31200 33600

# of connections 0 0 0 0 0 0

The following display shows output information for the show modem slot/port command for V.110

modem cards:

Router# show modem 0/1

Mdm Typ Status Tx/Rx G Duration TX RX RTS CTS DSR DCD DTR

0/1 Idle -/- 1 00:00:00 - - - - - - -

Modem 0/1, V.110 Terminal Adaptor (Unmanaged), Async2, TTY2

Firmware (Boot) Rev: Unmanaged (Unmanaged)

Modem config: Incoming and Outgoing

Management config: Unmanaged

Last clearing of "show modem" counters never

- incoming completes, - incoming failures

- outgoing completes, - outgoing failures

0 failed dial attempts, 0 ring no answers, 0 busied outs

- no dial tones, - dial timeouts, 0 watchdog timeouts

- no carriers, - link failures, 0 resets, - recover oob

- protocol timeouts, - protocol errors, - lost events

Connection Speeds 75 300 600 1200 2400 4800

# of connections - - - - - -

Connection Speeds 7200 9600 12000 14400 16800 19200

# of connections - - - - - -

Connection Speeds 21600 24000 26400 28800 31200 32000

# of connections - - - - - -

Connection Speeds 33600 34000 36000 38000 40000 42000

# of connections - - - - - -

Connection Speeds 44000 46000 48000 50000 52000 54000

# of connections - - - - - -

Connection Speeds 56000

# of connections -

V.110 Support for Cisco 3600 Series Digital Modems

show modem

9

Cisco IOS Release 12.1(5)T

The type of display output generated from the show modem slot/port command depends on the version

of Cisco IOS software running on the router or access server. For example, the following example shows

an example output for a 56K modem card, which carries digital modems that transmit at 56 kbps.

Note 56K modems do not modulate or demodulate data. A pure digital-to-digital connection is

made.

See Table 2 for a description of the fields displayed by this modem card.

Router# show modem 0/0

Mdm Typ Status Tx/Rx G Duration TX RX RTS CTS DSR DCD DTR

0/0 Idle 0/0 0 00:00:00 x x x x

Modem 0/0, Microcom MNP10 K56 Modem (Select), TTY1

Firmware (Boot) Rev: 3.1(16) (3.0(4))

DSP Controller (SPX) Rev: 1.1(0) (1.1(0))

Modem config: Incoming and Outgoing

Protocol: Normal, Compression: None

Management port config: Status polling and AT session

Management port status: Status polling and AT session

TX signals: 0 dBm, RX signals: 0 dBm

Last clearing of "show modem" counters never

0 incoming completes, 0 incoming failures

0 outgoing completes, 0 outgoing failures

0 failed dial attempts, 0 ring no answers, 0 busied outs

0 no dial tones, 0 dial timeouts, 0 watchdog timeouts

0 no carriers, 0 link failures, 1 resets 0 recover oob

0 protocol timeouts, 0 protocol errors, 0 lost events

Transmit Speed Counters:

Connection Speeds 75 300 600 1200 2400 4800

# of connections 0 0 0 0 0 0

Connection Speeds 7200 9600 12000 14400 16800 19200

# of connections 0 0 0 0 0 0

Connection Speeds 21600 24000 26400 28800 31200 32000

# of connections 0 0 0 0 0 0

Connection Speeds 33600 34000 36000 38000 40000 42000

# of connections 0 0 0 0 0 0

Connection Speeds 44000 46000 48000 50000 52000 54000

# of connections 0 0 0 0 0 0

Connection Speeds 56000

# of connections 0

Receive Speed Counters:

Connection Speeds 75 300 600 1200 2400 4800

# of connections 0 0 0 0 0 0

Connection Speeds 7200 9600 12000 14400 16800 19200

# of connections 0 0 0 0 0 0

Connection Speeds 21600 24000 26400 28800 31200 32000

# of connections 0 0 0 0 0 0

Connection Speeds 33600 34000 36000 38000 40000 42000

# of connections 0 0 0 0 0 0

Connection Speeds 44000 46000 48000 50000 52000 54000

# of connections 0 0 0 0 0 0

Connection Speeds 56000

# of connections 0

V.110 Support for Cisco 3600 Series Digital Modems

show modem

10

Cisco IOS Release 12.1(5)T

Table 2 describes the fields in the previous four displays, which were created using the show modem

slot/port command. This table applies to all modem module types.

Table 2 show modem slot/port Field Descriptions

Field Description

Mdm Slot and modem number.

Typ Modulation type, which can be any of the following values: Bel103, Bel212,

V110, V21, V22, V22bis, V23, V32, V32bis, VFC, V34, V17, V27, V33

and K56Flx

Status Current status of the modem. Possible values include:

Conn—Modem is connected to a remote host.

B—Inoperable state, which is configured by the modem bad command.

B*—Inoperable state, which is configured by the modem startup-test

command during initial power-up testing.

b—Modem is busied out. This can be manually configured by the modem

busyout line configuration command.

Reset—Modem is in reset mode.

D/L—Modem is downloading firmware.

Bad FW—Downloaded modem firmware is not operational.

Busy—Modem is out of service and not available for calls.

Idle—Modem is ready for incoming and outgoing calls.

Tx/Rx Transmission and receiving speed for the most recently connected call.

G Modem group number assigned to the modem. The group number 0 means

that the modem is not part of any group.

Duration Time duration of the current call or the last call.

Modem functions The following modem functions are displayed on manageable modems. A

field that is available and turned on is marked with an x. An unavailable

field is marked with a dash (-).

• TX—Transmit Data. The DTE device transmits data to the DCE device.

• RX—Receive Data. The DCE device receives data from the DTE

device.

• RTS—Request To Send. The DTE device signals to the DCE device

that the DTE device accepts data into its buffers.

• CTS—Clear To Send. The DCE device signals to the DTE device that

the DCE device accepts data into its buffers.

• DSR—Data Set Ready. The modem is ready to start communication.

• DCD—Data Carrier Detect. The DCE device indicates to the DTE

device that a call is present and established with a remote modem.

Dropping the DCD function terminates the session.

• DTR—Data Terminal Ready. The DTE device indicates to the DCE

device that it accepts calls.

Firmware Installed modem firmware.

V.110 Support for Cisco 3600 Series Digital Modems

show modem

11

Cisco IOS Release 12.1(5)T

Modem config Current modem configuration, which includes the fields Incoming,

Outgoing, Incoming and Outgoing, and Unknown.

Protocol Protocol the modem is running such as Normal, Direct, reliable/MNP4, and

reliable/LAPM (Link Access Procedure for Modems).

Compression Compression algorithm running on the modem, such as None, V42bis, and

MNP5.

Management config Indicates if the modem is configured for out-of-band feature polling.

TX signals Transmit signal levels. For modulations that do not support signal-to-noise

calculations, the ratio is 0.

RX signals Transmit signal levels.

Last clearing of “show

modem” counters

Last time the modem counters were cleared using the clear modem

counters command. A summary of modem events also appears:

• Incoming completes and failures—Total number of incoming

connection requests that the modem answered and successfully or

unsuccessfully connected with the remote DCE device.

• Outgoing completes and failures—Total number of outgoing

connection requests that the modem dialed and successfully or

unsuccessfully connected with the remote DCE device.

• Failed dial attempts—Number of times the modem attempted to dial

out but the call failed to leave the modem.

• Ring no answers—Number of times the integrated modem detected

ringing but did not answer the incoming call.

• Busied outs—Number of times the integrated modem was intentionally

taken out of service (for example, the modem busyout command was

enabled on the modem).

• No dial tones—Number of times the dial-out attempt failed because the

modem failed to detect a dial tone.

• Dial timeouts—Number of times the modem has timed out while

attempting to dial.

• Watchdog timeouts—Number of times the modem internal watchdog

timer has expired.

• No carriers—Number of times the modem disconnected because no

carrier was present.

• Link failures—Number of times the modem has detected a link failure.

• Resets—Number of times the modem has been reset.

• recover oob—Number of times the out-of-band feature has been

cleared and reinitialized.

• Protocol timeouts and errors—Number of times the modem protocol

failed to make a call connection.

• Lost events—Number of incomplete modem events performed by the

modem.

Transmit Speed

Counters

List of connection speeds that were sent by the modem.

Field Description

V.110 Support for Cisco 3600 Series Digital Modems

show modem

12

Cisco IOS Release 12.1(5)T

The following example shows the output for modem group 1, which is composed of modem 1/0 through

modem 1/23:

Router# show modem group 1

Incoming calls Outgoing calls Busied Failed No Succ

Grp Usage Succ Fail Avail Succ Fail Avail Out Dial Ans Pct.

1 0% 0 0 24 0 0 24 0 0 0 0%

Modem Group 1: 1/0, 1/1, 1/2, 1/3, 1/4, 1/5, 1/6, 1/7, 1/8, 1/9, 1/10, 1/11, 1/12, 1/13,

1/14, 1/15, 1/16, 1/17, 1/18, 1/19, 1/20, 1/21, 1/22, 1/23

Related Commands

Receive Speed Counters List of connection speeds that were received by the modem.

Connection Speeds # of

connections

A complete summary of possible connection speeds and the actual number

of connections that occurred at those speeds. Depending on which modem

port module and version of software you are running, possible connection

speeds range from 75 to 56,000 bps. The number of successful connections

is displayed directly beneath the connection speed identifier. For example,

the following output shows that three connections were made at 56 kbps.

Connection Speeds 56000 # of connections 3

Field Description

Command Description

show modem version Displays version information about the modem firmware, controller,

DSP code (for 56-kbps modems only), and boot code.

V.110 Support for Cisco 3600 Series Digital Modems

show modem log

13

Cisco IOS Release 12.1(5)T

show modem log

To display the modem history event status performed on a manageable modem or group of modems, use

the show modem log EXEC command.

show modem log [slot/port | group number]

Syntax Description

Defaults There are no default behaviors or values for this command.

Command Modes EXEC

Command History

Examples The following example shows a portion of the output display when using the show modem log

command. Since no specific modem or range of modems is designated, the data from all modems is

shown. The V.110 information is highlighted in this example.

Router# show modem log

Modem 0/0 Mica: Event Log contains 100 Events:

1d21h MICA-Cfg issued S-Reg configuration change:

configuration index = 59, value = 0x3

1d21h CSM: Incoming call from 9195555301 to Unknown

1d21h CSM: event-ISDN_CALL New State-IC_MODEM_RESERVED

CSM: status-1 dchan-3/2 bchan-0

...

1d21h CSM: event-MODEM_CONNECTED New State-CONNECTED_STATE

1d21h MICA-Qry Static Link Information:

Connect Protocol - V.110, Compression - None, Connected Standard - V110

Tx/Rx Symbol Rate - 0/0, Tx/Rx Carrier Freq - 0/0

Tx/Rx Trellis Coding - /, Frequency offset - 0Hz

Round trip delay - 0ms, Tx/Rx bit rate - 2400/2400

RBS pattern - 0x0, digital pad - , compensation - 0

1d21h MICA-Cmd Set Framing Mode to PPP.

...

1d21h MICA-Qry Final Link Information:

Call Time - 00:00:34, Disconnect Reason (0x8001) - SOFTWARE_RESET command

0 retrains and/or speed shifts, 0 ec retransmissions

9454 chars tx, 6577 chars rx, 0 chars rx bad

slot/port (Optional) Specifies the location of a slot and modem port. If this number

is not specified, statistics for all connected modems are displayed.

Remember to include the forward slash (/) when entering this variable.

group number (Optional) Specifies the location of a specific group of modems. If this

number is not specified, statistics for all modems in the access server are

displayed. The group number range is from 1 to 200.

Release Modification

11.2 This command was introduced.

12.1(5)T This command was modified to show display output for Cisco 3600 series

digital modems that support V.110.

V.110 Support for Cisco 3600 Series Digital Modems

show modem log

14

Cisco IOS Release 12.1(5)T

189 ppp packets tx, 129 ppp packets rx, 14 ppp packets rx bad

0 ec packets tx, 0 ec packets rx, 0 ec packets rx bad

0 v110 packets tx, 0 v110 packets rx, 0 v110 packets rx bad, 0 v110 sync loss

1d21h CSM: event-ASYNC_DTR_DOWN New State-IDLE_STATE

...

1d21h MICA-Cfg issued S-Reg configuration change:

S29 = 8 V.110 modem standard

1d21h MICA-Cfg issued S-Reg configuration change:

S57 = 3 User rate for V.110 connection is 3 bps

...

Related Commands Command Description

show modem

configuration

Displays the current modem configuration for digital MICA modems

loaded inside access servers or routers.

show modem mica Displays information about MICA digital modems.

show modem

operational-status

Displays the current modem operational status for MICA digital modems

loaded in access servers or routers.

V.110 Support for Cisco 3600 Series Digital Modems

show modem configuration

15

Cisco IOS Release 12.1(5)T

show modem configuration

To display the current modem configuration for digital MICA technologies modems loaded inside an

access server or router, use the show modem configuration EXEC command.

show modem configuration [slot/port]

Syntax Description

Defaults There are no default behaviors or values for this command.

Command Modes EXEC

Command History

Examples The following example shows the display output when using the show modem configuration command.

A specific modem, 0/0, has been designated. V.110 information is highlighted in this example.

Router# show modem configuration 0/0

S-Reg Value Meaning

——-|——-|———————————————

S-- = 1 Country Code is Default u-law

S00 = 0 Auto Answer immediately

S01 = 0 Reserved

S02 = 43 escape character is 0x2B or '+'

S03 = 13 carriage return character is 0xD

S04 = 10 line feed character is 0xA

S05 = 8 backspace character is 0x8

S06 = 2 pause 2 seconds before blind dialing

S07 = 60 wait up to 60 seconds for carrier after dialing

S08 = 2 comma adds 2 second dial delay

S09 = 317 BitMap register value = 0x13D

S10 = 14 1.4 second delay for hangup after carrier loss

S11 = 0 In Answer Mode

S12 = 3 3 Data Bits

S13 = 3 Space Parity

S14 = 1 1 Stop Bits

S15 = 1 V.42 ODP generation enabled

S16 = 50 5.0 second Error Correction autodetect timeout

S17 = 100 10.0 second Error Correction negotiation timeout

S18 = 13 Error Correction fallback char is 0xD

S19 = 12 Error Correction retransmission limit is 12

S20 = 256 Error Correction frame length is 256 octets

S21 = 3 V42bis or MNP Data Compression

slot/port (Optional) Specifies the location of a slot and modem port. If this number

is not specified, statistics for all connected modems are displayed.

Remember to include the forward slash (/) when entering this variable.

Release Modification

11.2P This command was introduced.

12.1(5)T This command was modified to show output display for Cisco 3600 series

digital modems that support V.110.

V.110 Support for Cisco 3600 Series Digital Modems

show modem configuration

16

Cisco IOS Release 12.1(5)T

S22 = 0 ARA Error Correction is disabled

S23 = 1 V.42 Error Correction enabled

S24 = 1 MNP Error Correction enabled

S25 = 0 Link Protocol Fallback to Async framing

S26 = 0 Using TDM slice 0

S27 = 0 Calling Tone disabled

S28 = 0 Guard Tone disabled

S29 = 8 V.110 modem standard

S30 = 33600 Maximum connect rate of 33600 bps

S31 = 300 Minimum connect rate of 300 bps

S32 = 2 Bit Errors >= 1:1000 cause recovery

S33 = 500 Fallback/Fallforward Squelch Timer is 500ms

S34 = 2000 Fall Forward Timer is 20.0 seconds

S35 = 50 Fall Back Timer is 0.50 seconds

S36 = 20 Terminate timeout is 20 seconds

S37 = 60 Wait 60 seconds for data mode timeout

S38 = 14 1.4 second lost carrier to hang-up delay

S39 = 7 Transmit level setting of -13dBm

S40 = 4 4 consecutive retrains cause link disconnect

S41 = 5 V.34 maximum symbol rate of 3429 baud

S42 = 0 V.34 minimum symbol rate of 2400 baud

S43 = 2 V.34 carrier frequency is Auto Selection

S44 = 11 V.34 Preemphasis filter selection is Automatic

S45 = 0 Null transmit and receive Signalling Type

S46 = 0 No call progress tone detection

S47 = 2 +++ escape detection enabled for originate mode only

S48 = 1 AT command processor enabled

S49 = 0 no call setup delay

S50 = 60000 Maximum PCM connect rate of 60000 bps

S51 = 28000 Minimum PCM connect rate of 28000 bps

S52 = 1 Digital Pad Compensation is enabled

S53 = 3 V.8bis is enabled

S57 = 2400 User rate for V.110 connection is 2400 bps

configuration index = 59, value = 0x3

Related Commands Command Description

show modem log Displays the modem history event status performed on a manageable

modem or group of modems.

show modem mica Displays information about MICA digital modems.

show modem

operational-status

Displays the current modem operational status for MICA digital modems

loaded in access servers or routers.

V.110 Support for Cisco 3600 Series Digital Modems

show modem connect-speeds

17

Cisco IOS Release 12.1(5)T

show modem connect-speeds

To display connection speed statistics for all modems running in an access server or router, use the show

modem connect-speeds EXEC command. There is no no form of this command.

show modem connect-speeds [max-speed [slot]]

Syntax Description

Defaults The maximum speed displayed is 12,000 bps.

Command Modes EXEC

Command History

Usage Guidelines Because most terminal screens are not wide enough to display the entire range of connection speeds at

one time (for example, 75 to 56,000 bps), the max-speed variable is used. This variable specifies the

contents of a shifting baud-rate window, which provides you with a snapshot of modem connection

speeds for your system. If you want to see a snapshot of lower baud rates, specify a lower connection

speed. If you want to see a snapshot of higher baud rates, specify a higher connection speed.

The Cisco IOS software rounds up the max-speed variable to the nearest recognizable baud rate, so you

do not need to memorize or enter exact connection speeds. For example, if you enter a maximum baud

rate of 22059, the system software automatically rounds the value up to 24000.

To display a complete picture of all connection speeds and counters on the system, you must enter a

series of commands. Each time you issue the show modem connect-speeds max-speed command, only

nine baud rate columns can be displayed at the same time.

Table 3 shows a range of commands that you can issue, one at a time, to see a complete picture of the

total possible connection speeds on your access server.

Table 3 Connect Speed Displays for show modem connect-speeds

Command

max-speed (Optional) Maximum speed you want displayed in the shifting speed

window. You can specify from 12,000 to 56,000 bps.

slot (Optional) Specifies the slot number, which limits the display output to a

particular range of modems in the system.

Release Modification

11.3 This command was introduced.

12.1(5)T This command was modified to show display output for Cisco 3600 series

digital modems that support V.110.

Command Connect Speed Range Displayed

show modem connect-speeds 56000 40,000 to 56,000 bps

show modem connect-speeds 38000 24,000 to 38,000 bps

V.110 Support for Cisco 3600 Series Digital Modems

show modem connect-speeds

18

Cisco IOS Release 12.1(5)T

Note The Cisco IOS software does not accept commas (,) in the connect speed field. For

example, enter 28000 not 28,000.

The show modem connect-speeds command displays a log of connection speed statistics starting from

the last time the access servers or router was power cycled or the clear modem counters command was

issued. If you want to create a monthly report of the connection speeds achieved by the modems, issue

the clear modem counters command at the beginning of the month and issue the show modem

connect-speeds command at the end of the month.

Examples

Router# show modem connect-speeds

Codes:

* - Modem has an active call

R - Modem is being Reset

D - Download in progress

B - Modem is marked bad and cannot be used for taking calls

b - Modem is either busied out or shut-down

Transmit connect speeds

Mdm 75 300 600 1200 2400 4800 7200 9600 12000 TotCnt

* 0/0 0 0 0 36 35 61 0 0 0 132

* 0/1 0 0 0 1 0 0 0 0 0 1

0/2 0 0 0 48 45 37 0 0 0 130

* 0/3 0 0 0 86 36 4 0 0 0 126

* 0/4 0 0 0 0 0 1 0 0 0 1

0/5 0 0 0 20 33 78 0 0 0 131

* 0/6 0 0 0 25 57 49 0 0 0 131

0/7 0 0 0 47 48 36 0 0 0 131

b 0/8 0 0 0 0 0 0 0 0 0 0

!.

b 0/29 0 0 0 0 0 0 0 0 0 0

Tot 0 0 0 263 254 266 0 0 0 783

Tot % 0 0 0 33 32 33 0 0 0

Receive connect speeds

Mdm 75 300 600 1200 2400 4800 7200 9600 12000 TotCnt

* 0/0 0 0 0 36 35 61 0 0 0 132

* 0/1 0 0 0 1 0 0 0 0 0 1

0/2 0 0 0 48 45 37 0 0 0 130

* 0/3 0 0 0 86 36 4 0 0 0 126

* 0/4 0 0 0 0 0 1 0 0 0 1

0/5 0 0 0 20 33 78 0 0 0 131

* 0/6 0 0 0 25 57 49 0 0 0 131

0/7 0 0 0 47 48 36 0 0 0 131

b 0/8 0 0 0 0 0 0 0 0 0 0

!.

b 0/29 0 0 0 0 0 0 0 0 0 0

show modem connect-speeds 21600 2,400 to 21,600 bps

show modem connect-speeds 1200 75 to 1200 bps

Command Connect Speed Range Displayed

V.110 Support for Cisco 3600 Series Digital Modems

show modem connect-speeds

19

Cisco IOS Release 12.1(5)T

Tot 0 0 0 263 254 266 0 0 0 783

Tot % 0 0 0 33 32 33 0 0 0

Router# show modem connect-speeds ?

<12000-64000> Max baud connect speed to display to

| Output modifiers

<cr>

Router# show modem connect-speeds 12000 ?

<0-3> Slot number

| Output modifiers

<cr>

Router# show modem connect-speeds 12000 2

Codes:

* - Modem has an active call

R - Modem is being Reset

D - Download in progress

B - Modem is marked bad and cannot be used for taking calls

b - Modem is either busied out or shut-down

Transmit connect speeds

Mdm 75 300 600 1200 2400 4800 7200 9600 12000 TotCnt

Tot 0 0 0 263 254 266 0 0 0 783

Tot % 0 0 0 33 32 33 0 0 0

Receive connect speeds

Mdm 75 300 600 1200 2400 4800 7200 9600 12000 TotCnt

Tot 0 0 0 263 254 266 0 0 0 783

Tot % 0 0 0 33 32 33 0 0 0

The following example shows connection speed statistics up to 28,000 bps:

Router# show modem connect-speeds 28800

transmit connect speeds

Mdm 9600 12000 14400 16800 19200 21600 24000 26400 28800 TotCnt

* 1/0 0 0 0 0 3 4 6 37 23 74

* 1/1 0 0 3 1 0 4 9 41 20 80

* 1/2 0 0 2 0 1 3 10 37 26 82

1/3 1 0 0 0 0 3 15 35 7 62

1/4 0 0 0 0 4 2 8 20 13 49

* 1/5 0 0 4 0 1 0 4 38 17 65

* 1/6 0 0 2 1 0 1 9 32 11 57

* 1/7 1 0 2 0 0 5 10 31 18 67

* 1/8 0 0 0 1 1 1 10 42 11 68

1/9 0 0 2 1 2 4 4 30 23 67

1/10 0 0 0 0 0 2 5 26 22 56

* 1/11 0 0 0 0 3 1 16 38 17 76

* 1/12 0 0 0 0 0 3 7 40 12 62

1/13 0 0 0 1 2 3 11 20 14 51

1/14 0 0 2 0 0 2 7 26 12 51

1/15 0 0 1 1 1 2 6 29 25 65

1/16 2 0 2 0 1 5 10 37 15 73

1/17 0 0 0 0 0 2 10 33 22 67

1/18 0 0 2 2 0 2 12 17 25 61

* 1/19 2 0 3 0 1 2 9 35 20 74

1/20 0 0 2 2 2 2 8 28 21 65

* 1/21 0 1 2 0 1 2 5 23 21 58

V.110 Support for Cisco 3600 Series Digital Modems

show modem connect-speeds

20

Cisco IOS Release 12.1(5)T

* 1/22 0 0 1 0 1 1 5 27 21 56

* 1/23 0 0 2 0 0 4 8 30 15 60

Tot 6 1 32 10 24 60 204 752 431 1546

Tot % 0 0 2 0 1 3 13 48 27

receive connect speeds

Mdm 9600 12000 14400 16800 19200 21600 24000 26400 28800 TotCnt

* 1/0 0 0 1 0 1 2 9 35 25 74

* 1/1 0 0 3 0 1 3 10 42 18 80

* 1/2 0 0 2 0 1 4 8 40 26 82

1/3 1 0 0 0 0 1 10 36 14 62

1/4 0 0 1 0 2 2 8 22 8 49

* 1/5 0 1 4 0 0 0 9 32 17 65

* 1/6 0 0 2 0 0 0 7 33 14 57

* 1/7 0 0 2 1 1 0 6 39 18 67

* 1/8 0 0 0 0 1 0 11 43 12 68

1/9 1 0 3 0 0 0 8 33 22 67

1/10 0 0 0 0 1 1 6 31 17 56

* 1/11 0 0 0 1 1 1 14 43 16 76

* 1/12 0 0 0 0 0 0 5 43 12 62

1/13 0 0 0 0 0 2 10 26 13 51

1/14 0 0 2 1 0 0 5 27 14 51

1/15 0 0 1 0 1 2 3 36 22 65

1/16 1 0 3 1 2 0 8 37 20 73

1/17 0 0 0 0 0 0 8 36 22 67

1/18 0 1 1 0 0 2 4 30 20 61

* 1/19 0 0 3 2 1 1 6 42 18 74

1/20 0 1 2 1 2 1 2 37 18 65

* 1/21 0 0 3 3 1 2 2 28 18 58

* 1/22 0 0 1 0 1 0 5 32 16 56

* 1/23 0 0 2 0 0 1 8 35 13 60

Tot 3 3 36 10 17 25 172 838 413 1546

Tot % 0 0 2 0 1 1 11 54 26

The following example shows connection speed statistics up to 56,000 bps:

Router# show modem connect-speeds 56000

transmit connect speeds

Mdm 40000 42000 44000 46000 48000 50000 52000 54000 56000 TotCnt

1/0 0 0 0 0 0 0 0 0 0 0

1/1 0 0 0 0 0 0 0 0 0 0

1/2 0 0 0 0 0 0 0 0 0 0

!.

1/23 0 0 0 0 0 0 0 0 0 0

Tot 0 0 0 0 0 0 0 0 0 0

Tot % 0 0 0 0 0 0 0 0 0

receive connect speeds

Mdm 40000 42000 44000 46000 48000 50000 52000 54000 56000 TotCnt

1/0 0 0 0 0 0 0 0 0 0 0

1/1 0 0 0 0 0 0 0 0 0 0

1/2 0 0 0 0 0 0 0 0 0 0

!.

Page is loading ...

Cisco 3600 User manual

This manual is also suitable for

Cisco 3600 User manual

Related papers

Other documents