Briggs & Stratton 1695353 User manual

Brand: Briggs & Stratton

Model: 1695353

Category: Lawnmowers

Type: User manual

OPERATOR’S

MANUAL

Turboless Twin Catcher

Mfg. No. Description

1695353 38” Turboless Twin Catcher

Turboless Twin Catcher

Manual Part No. 1734772

Revision 01

Rev. Date 05/2007

TP 100-4528-01-AT-SMAN

CCAAUUTTIIOONN:: RReeaadd aanndd

ffoollllooww aallll iinnssttrruuccttiioonnss..

SAVE THESE INSTRUCTIONS

READ THE MANUAL

The operator’s manual contains important safety information you need to be aware of BEFORE you

operate your unit as well as DURING operation.

Safe operating techniques, an explanation of the product’s features and controls, and maintenance

information is included to help you get the most out of your equipment investment.

Failure to obey the safety rules could result in loss of control of the unit, sever personal injury or death to

you, or bystanders, or damage to property or equipment.

Hazard Symbols and Meanings

Safety Icon Hazard Safety Icon Hazard

Alert Read the

Manual

Thrown

Objects

Remove Key

Before

Servicing

Machine

Rollover

Rotating

Parts – Do

Not Touch

Safety Icons

The alert symbol is used to identify safety information

about hazards that can result in personal injury. A signal

word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelyhood and the potential

severity of the injury. In addition, a hazard icon may be used

to represent the type of hazard. An explanation of hazard

levels and icons are as follows:

DANGER

This indicates a hazard which, if not avoided, will result in

serial injury or death.

WARNING

This indicates a hazard which, if not avoided, could result in

serial injury or death.

CAUTION

This indicates a hazard which, if not avoided, might result in

minor or moderate injury.

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mowing with the Catcher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Storing the Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install Mounting Plates & Spacers (Broadmoor/1600/2600/LT Series) . . . . 5

Install Baffle and Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Install Lower Chute Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Bag and Cover Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Install Hitch and Upright Support Assembly . . . . . . . . . . . . . . . . . . . . . . . . 8

Install Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Install Collector Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Install Lower Discharge Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Install Discharge Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Normal Removal & Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Lower Discharge Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Bagger Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Normal Removal

& Installation

AssemblyOperatror Safety

Safety

• Know the unit’s controls and how to stop quickly.

READ THE OPERATOR’S MANUALS.

• Read and obey all safety decals.

• Only allow responsible adults, who are familiar with

the instructions, to operate the unit.

• Disengage the PTO. Shut off the engine and wait

for all moving parts to stop before attaching,

adjusting, or disconnecting any part of the

collection system.

• Check the collection system to make sure it is

bolted tightly to the unit.

• DO NOT operate the unit without either the entire

grass catcher or the deflector in place.

• Turn off the PTO to disengage the blades when not

mowing.

• DO NOT mow in reverse unless absolutely

necessary. Always look down and behind before

and while travelling in reverse.

• DO NOT turn sharply when travelling alongside a

building or any object. Slow down before turning.

• DO NOT carry passengers.

• When collection system is removed from the

mower deck, the deflector must be properly

installed.

• Collector bags are subject to deterioration and

wear during normal use. Inspect the bag

periodically for tears, holes, or weak spots and

replace with a new bag that meets manufacturer’s

durability standards.

• If the mower stalls or the collector chute plugs:

1. Disengage the PTO;

2. Stop the engine and remove the key;

3. Set the parking brake, and wait for all moving

parts to stop.

4. Remove the foreign object or clear the chute

with a piece of wood before restarting the engine.

NEVER place hands into COLLECTOR OR

MOWER housing to clear jammed objects.

Blower OR MOWER may rotate when object is

removed.

• For added stability and to prevent tipping or loss of

control:

a. Use reduced speed on uneven ground and

when turning corners.

b. Reduce loads on hillsides. It is recommended

that the collection system be kept only half full

when negotiating any slopes. Start mowing on

slopes when the collection system is empty.

c. Mow up and down the face of slopes; never

across the face of any slope.

• Never operate on slopes greater than 17.6%

(10°).

GENERAL WARNINGS

SAFETY DECALS

This unit has been designed and manufactured to

provide you with the safety and reliability you would

expect from an industry leader in outdoor power

equipment manufacturing.

Although reading this manual and the safety

instructions it contains will provide you with the

necessary basic knowledge to operate this equipment

safely and effectively, we have placed several safety

labels on the unit to remind you of this important

information while you are operating your unit.

All DANGER, WARNING, CAUTION and

instructional messages on your rider, attachments

and mower should be carefully read and obeyed.

Personal bodily injury can result when these

instructions are not followed.The information is for

your safety and it is important! The safety decals

below are on your product.

If any decals are lost or damaged, replace them at

once. See your local dealer for replacements.

TP 600-2562-01-AT-SMA

Attachment Decal

These labels are easily applied and will act as a

constant visual reminder to you, and others who may

use the equipment, to follow the safety instructions

necessary for safe, effective operation.

Thrown objects hazard

• Objects thrown by the mower can seriously

injure or kill you.

• Do not open the hopper while the mower blades

are turning.

• Do not operate the mower without the complete

catcher in place.

WARNING

1732819

Decal - WARNING Thrown

Objects Hazard

Part Number 1732819

Read and obey all operation and warning decals.

Before Operation

Clear the lawn of all sticks, stones, wire and other

debris which may be caught or thrown by the mower

blades.

Check grass condition. If wet, wait until later in the

day. If grass is wet, the grass catcher is likely to

become plugged.

For efficient bagging, air circulation under the

mower deck, through the chute and into the bag

is very important.

For this reason, BEFORE YOU BEGIN MOWING you

should make certain the underside of the mower and

the underside of the catcher lid are free from grass

and debris.

Make sure that there is a snug fit between mower

deck, blower housing, tubes, and grass catcher cover.

Mowing with the Catcher

Always operate with throttle at full speed when

mowing.

Grass should be cut often, and not too short. If grass

is too long or lush it may be necessary to keep

ground speed to a minimum or to cut only half the

width of the mower to prevent clogging. If grass is

long, operate with mower in high cutting position for

first pass, cutting again in a lower position on a

second pass.

Do not open the cover with mower engaged.

If a large amount of cut grass is spilling out from

under deck, the tube may be plugged or the bags

may be full— discontinue mowing, stop the unit,

disengage the PTO, shut off the engine and then

empty the catcher or clear the tube.

WARNING

ALWAYS shut off the tractor. Disengage the

PTO, and allow all moving parts to stop

BEFORE disconnecting or clearing tube, or

emptying catcher.

Before leaving the operator’s position for any

reason, engage the parking brake, disengage

the PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider

and mower free of grass, leaves and excess

grease. Do not stop or park rider over dry

leaves, grass or combustible materials.

Never operate on slopes greater than 17.6% (10°).

After Operation

Remove any debris from the the screen on the

underside of the lid.

The blower housing and tube should be removed for

cleaning.

Inspect the grass bags for wear or damage. Make

sure that there is a snug fit between mower deck,

blower housing, tubes, and grass catcher cover.

Storing The Grass Catcher

Clean the grass catcher thoroughly using a mild

detergent (other products may damage the tube).

Remove any debris from the screen on the underside

of the lid.

If paint has been scratched on metal parts, touch up

with paint, or apply a thin film of oil to prevent

corrosion.

Store in a dry area. Dry thoroughly before storing for

a long period of time. Always store away from

moisture.

Do not leave grass in bagger containers.

Empty containers after each use and before

storing. Failure to do so may result in

spontaneous combustion which could develop

into a fire.

CAUTION

Before you begin operating the unit be certain

you have read all of the safety and operational

information of this instruction sheet, as well as

the Operator’s Manual for the tractor and any

other attachments.

Safety

Notes

INSTALL MOUNTING PLATES -

BROADMOOR / 1600 / 2600 / LT

SERIES

Install Plates & Spacers

1. Mount the side brackets (C, Figure 1) to both

sides of the frame using the holes shown. Secure

with one 3/8-16 x 1 capscrew (D), 3/8 lockwasher

(B), and 3/8-16 nut (A) per side.

2. Install the rear spacers (C, Figure 2). Secure with

two 1/2-13 x 2-1/2 capscrews (E), washers (D),

spacers (C), and 1/2-13 nylock nuts (A) per side.

Figure 1. Install Side Brackets

A. Nut, 3/8-16

B. Lockwasher, 3/8

C. Side Bracket

D. Capscrew, 3/8-16 x 1

Figure 2. Install Rear Spacers

A. Nylock Nuts, 1/2-13

B. Capscrew, 1/2-13 x 2-1/2

C. Spacers

D. Washers, 1/2

Assembly

Install Baffle and Blade

Note: Units with an anti-blowout baffle do not require

the Clean Sweep baffle.

1. Remove mower deck. See OPERATOR’S

MANUAL.

2. Install notched side of baffle (A, Figure 3) to

discharge side of deck securing with 5/16-18 x 2

carriage bolt (C) and 5/16-18 locknut (D). Install

5/16-18 wing nut (F) and locknut (G) to carriage

bolt (C) as shown.

3. Secure center of baffle (A) to deck using 5/16-18 x

2 carriage bolt (C), spacer (B) and nut (D).

Secure LH end of baffle (A) to deck using 5/16-18

x 5/8 carriage bolt (E) and nut (D).

4. Remove right hand blade (A, Figure 5). Use a

block of wood to prevent blade rotation while

loosening the capscrew.

5. Reinstall the large washer (B, Figure 6), spring

washer (C) and capscrew (D). Use a wooden

block (A) to prevent blade rotation while tightening

the capscrew (D) to 45-55 ft. lbs. (61-75 Nm).

Figure 3. Baffle Assembly

A. Baffle (New)

B. Spacer (New)

C. Carriage Bolts,

5/16-18 x 2 (New)

D. Locknuts,WHIZ Lock,

5/16-18 (New)

E. Carriage Bolt,

5/16-18 x 5/8 (New)

F. Wing Nut Assembly,

Large, 5/16-18 (New)

G. Locknut, Center Lock,

5/16-18 (New)

H. Grass Shield (Existing)

I. Blade, High Lift (New)

J. Hex Washer (Existing)

K. Washer (Existing)

L. Capscrew,

7/16-14 x 1-1/4 (Existing)

LOOSEN

Figure 4. Blade Removal

A. Blade

Figure 5. Blade Installation Mowers

A. 4x4 Wood Block

B. Hex Washer

C. Spring Washer

D. Blade Capscrew

Torque Capscrew to

45-55 ft. lbs. (61-75 Nm)

Assembly

Figure 6. Install Pin and Bracket

A. Lower Chute

B. Locknut, 1/4-20

C. Puck, Metal

D. Capscrews,Thin Head, 5/16-18 x 3/4

E. Locknuts, 5/16-18

F. Bracket

G. Defflector Prop

Install Lower Chute Components

INSTALL BRACKET AND PIN ON LOWER CHUTE

1. Secure the puck (C, Figure 6) to lower chute (A)

using 5/16-18 x 3/4 capscrew (D) and 5/16-18

locknut (E).

2. Install bracket (F) and deflector prop (G) to lower

chute (A) using 5/16-18 x 3/4 capscrews (D) and

5/16-18 locknuts (E).

Figure 9. Install Cover Assembly

A. Bag Support Bracket

B. Cover Assembly

C. Cover Hinge Pins

D. Hair Pins

E. Hinge Pivots

INSTALL COVER ASSEMBLY

1. Attach cover assembly (B, Figure 9) to bag

support bracket (A) using hinge pivots (E). Secure

cover using cover hinge pins (C) and hair pins (D)

as shown.

Figure 8. Attach Hitch and Upright Support

A. Hitch and Upright Support Assembly

B. Frame spacers

INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY

1. Attach hitch and upright support assembly (A,

Figure 8) to frame spacers (B) as shown.

INSTALL BAG AND COVER SUPPORT

1. Install the bag and cover support (B, Figure 7) to

upright support (A) using reinforcement plate (C)

and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts

(E) as shown.

Figure 7. Install Bag and Cover Support

A. Upright Support

B. Bag and cover Support

C. Reinforcement Plate

D. Capscrews, 3/8-16 x 1

E. Locknuts, 3/8-16

Assembly

INSTALL COLLECTOR BAGS

1. Raise the cover (A, Figure 10).

2. Attach collector bags (B) using grass bag hanger

Figure 10. Install Collector Bags

A. Cover

B. Collector Bag

C. Grass Bag Hanger

D. Bag Hanger Posts

Figure 11. Install Lower Discharge Chute

A. Lower Chute

B. Wing Nut

C. Nut

D. Carriage Bolt

E. Discharge Deflector

F. Deflector Hinge Rod

G. Bracket

INSTALL LOWER DISCHARGE CHUTE

1. Lift discharge deflector up (E, Figure 11).

2. Slide the notch of bracket (G) on to deflector hinge

rod (F).

3. Secure the front of lower chute (A) to carriage bolt

(D) using wing nut (B) and locknut (C).

Note: Locknut (C) is intended to keep wing nut (B)

permanently on carriage bolt (D).

Assembly

INSTALL DISCHARGE TUBE

1.Slide discharge tube (B, Figure 12) into seal (C). It

may be necessary to lengthen several slits (F) in

order for tube (A) to fit into seal (B)

2. Attach the discharge tube (B and Inset) to boot (A)

and secure the tube by moving wire form (E) down

over metal puck (D).

Assembly

Figure 12. Install Discharge Tube

A. Boot

B. Discharge Tube

C. Seal

D. Puck, Metal

E. Wire Form

F. Slits

Normal Removal

& Installation

Normal Removal & Installation of

Lower Discharge Chute

Note: See previous pages for more detailed

installation and operation instructions if necessary.

1. Lift discharge deflector up (E, Figure 13).

2. Slide the notch of bracket (G) on to deflector hinge

rod (F).

3. Secure the front of lower chute (A) to carriage bolt

(D) using wing nut (B) and locknut (C).

Note: Locknut (C) is intended to keep wing nut (B)

permanently on carriage bolt (D).

Figure 13. Install Lower Discharge Chute

A. Lower Chute

B. Wing Nut

C. Locknut

D. Carriage Bolt

E. Discharge Deflector

F. Deflector Hinge Rod

G. Bracket

Figure 14. Normal Installation & Removal

WARNING

OPERATION WITHOUT BAGGER

For operation without bagger, the mower

deflector MUST be properly installed in the

down position and retained by the spring latch.

Normal Removal

& Installation

A. Hitch Support

Assembly

B. Cover

C. Pin

D. Hair Pins

E. Bag

F. Grass Bag Hanger

G. Discharge Tube

H. Wire Form

I. Puck

J. Boot

K. Seal

L. Frame Spacers

Bagger Removal

1. Disconnect the discharge tube (G, Figure 14) from

boot (J) by moving wire form (H) up and out from

metal puck (I). Remove discharge tube (G) from

seal (K).

2. Remove hair pin clips (D) and pins (C) then

remove cover (B) see Figure 9.

Note: To prevent loss of parts reinstall pins (C) and

hair pins (D) in support assembly hinge pivots (E,

Figure 9).

3.Remove and empty bags (E, Figure 10).

4. Lift discharge deflector up (E, Figure 13).

5. Loosen (do not remove) wing nut (B) and lock nut

(C).

6. Slide lower chute (A) off carriage bolt (D) and

deflector hinge rod (F).

Normal Removal

& Installation

Briggs & Stratton Yard Power Products Group

500 N Spring Street / PO Box 997

Port Washington, WI 53074-0997

www.MasseyLawn.com

MANUFACTURING, INC.

500 N Spring Street / PO Box 997

Port Washington, WI 53074-0997

www.SimplicityMfg.com

500 N Spring Street / PO Box 997

Port Washington, WI 53074-0997

AGCOLawn.com

PRODUCTS

535 Macon Street

McDonough, GA 30253

www.Snapper.com

Briggs & Stratton 1695353 User manual

Brand: Briggs & Stratton

Model: 1695353

Category: Lawnmowers

Type: User manual

Download PDF

report

Briggs & Stratton 1695353 User manual

Briggs & Stratton 1695353 User manual

Related papers

Other documents