DECK MOUNT BATH FILLER
SERIN
™
*Wrench
Certified to comply with ANSI A112.18.1M
Recommended Tools
*Supplied with Fitting
*Hex key
Turn off hot and cold water
supplies before beginning.
CAUTION
1
2
Insert SPOUT SHANK (3) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (1) is properly seated in RECESS
of ESCUTCHEON RING (2).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (3). From underside of ledge secure SPOUT (7) into position
with LOCKNUT (6).
SPOUT ASSEMBLY
PREPARE TUBE AND TEE ASSEMBLY
4
2
3
1
3
4
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
VALVE inlet is
3/4-inch NPT male.
NOTE
MOUNTING
SURFACE
3-1/4" D.
(82mm) D.
2" D.
(52mm) D.
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
9-1/2"
(240mm)
6-3/4"
(170mm)
9-3/4"
(247mm)
2-3/4"
(71mm)
6-1/2" to 12"
(165mm to 305mm)
Installation
Instructions
2064.90X
1-1/2 MAX.
(38mm) MAX.
1-3/16" MAX.
(30mm) MAX.
1-3/16 D.
(30mm) D.
3'
(76mm)
(H)
(C)
1-1/8 D.
12 MAX.
(305mm)
2-1/16" D.
(52mm) D.
1-1/16 D.
(27mm) D.
3/4-14 MALE
N.P.T. INLETS
Tubing Cutter
RECESS
3
7
1
4
6
2
5
MOUNTING
SURFACE
6-1/2" to 12"
(165mm to 305mm)
Install RUBBER RING (1) into ESCUTCHEON RING (2) and
place over mounting hole.
M968830 Rev.1.4
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
9
2
4
5/16'' MIN.
MOUNTING
SURFACE
10
11
11
10
1
3
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to
SPOUT SHANK (6) and tighten using a 10mm (3/8'') hex wrench. Tighten
COUPLING (8) using a 10mm (3/8") Hex wrench. (FOR 2064.901). Use
COUPLING (8a) for fitting less spray.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) with WRENCH supplied to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
12
4
13
7
6
8
8a
5
13
12
3
4
MOUNTING
SURFACE
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING
SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
M968830 Rev.1.4
Wrench
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Thread counter-clock wise HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3).
Use a flat blade screw driver to remove SPRING CLIP (4).
Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (4).
Reinstall HANDLE ASSEMBLY (2).
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
SERVICE
90˚
VALVE
1
5
3
4
2
4
5
INSTALL HANDLES
1
2
4
5
3
TOP
Figure "A"
SPLINE
END UP
Push ADAPTER (1) on VALVE STEM (2). See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5)
until snug against mounting surface
.
THREAD ON
TO DECK
ADAPTER
Hex wench
(supplied)
HANDSHOWER INSTALLATION (For 2064.901 only)
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in SPRAY ESCUTCHEON (1). Install RUBBER WASHER (3), BRASS WASHER (4)
and LOCKNUT (5) from underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (5).
Install SEAL (9) and connect HOSE (10) to outlet nipple at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and SPRAY ESCUTCHEON (1). Note: SPRAY
HOLDER (6) must be seperate from ESCUTCHEON (1) to
pass HOSE (8) through ESCUTCHEON.(1)
Insert SEAL (9) into SHOWER HOSE (8). Connect HOSE (8)
to HOSE (10).
Install SEAL (9) and connect HAND SHOWER (11) to
SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles to
avoid damage during construction.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Unthread LIFT ROD KNOB (2) and remove.
Remove PLUG BUTTON (3) and remove SET SCREW (4) using
4mm hex wrench supplied.
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER
RING (6).
Unthread SHANK SLEEVE (7) and remove from SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (6) is properly seated in its recess at the base of the
SPOUT (1). Make certain SET SCREW (4) is properly aligned
and tight so that SPOUT (1) is locked in place.
6
1
2
3
5
7
8
10
9
9
9
11
1
8
4
3
2
4
6
6
5
7
VIEW "A"
VIEW "A"
7
MAKE WATER SUPPLY CONNECTIONS
8
9
7A
With HANDLES in OFF position, turn on
WATER SUPPLIES and check all connections
for leaks.
Operate both HANDLES to flush water lines
thoroughly.
Connect HOT water supply to LEFT INLET
UNION (1) and COLD water supply to
RIGHT INLET UNION (2). Pipe connections
are 3/4" NPT. Use sealant or Teflon tape
on pipe connections.
Do not solder directly to valve body.
TEST INSTALLED FAUCET
3/4" X 3/4" NPT UNION
(NOT SUPPLIED)
HOT
COLD
3/4" NPT
HAND
SHOWER
TRANSFER KNOB
3/4" NPT
2
1
Lift HAND SHOWER from HOLDER, direct spray
into tub. Lift TRANSFER KNOB to check HAND
SHOWER and HOSES for leaks.
Turn handles "off" and replace HAND SHOWER.
IMPORTANT: It is strongly recommended that access be
provided for all enclosed mechanical parts to this system.
M968830 Rev.1.4
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
028679-0070A
TUBE & TEE
ASSEMBLY
DECK-MOUNT
BATH FILLER
012668-0070A
SHANK KIT
030274-0070A
SHANK MOUNTING KIT
M962347-YYY0A
SPOUT ESCUTCHEON KIT
012078-0070A
VALVE COUPLING KIT
994053-0070A
VALVE
MODEL NUMBER
028664-YYY0A
HAND SHOWER
HOLDER
M953169-YYY0A
HAND SHOWER
028699-0070A
COUPLING (FOR TRANSFER)
028698-0070A
COUPLING
028667-0020A
HAND SHOWER HOSE
A952849-0070A
CHECK VALVE
051343-0070A
HOSE KIT
030275-0070A
SHANK SLEEVE KIT
M962346-YYY0A
TRANSFER
ROD ASSEMBLY
M962418-YYY0A
SPOUT KIT (2064.901)
M962489-YYY0A
SPOUT KIT (2064.900)
M962414-YYY0A
DECK
ESCUTCHEON KIT
M950245-YYY0A
HANDLE
ASSEMBLY
SERIN
™
2064.90X
M962269-YYY0A
SPOUT END
918555-0070A
HANDLE SCREW
918049-0070A
HANDLE ADAPTER
M961634-0070A
VALVE
MOUNTING
KIT
M968830 Rev.1.4
CHROME
SATIN NICKEL
002
295
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
IN MEXICO 01-800-839-12-00
/
