Defy DGS178 User manual

Category
Stoves
Type
User manual
Page 1
DGS178 - DGS181
50 CM GE 3B 1S ELECTRIC OVEN
Cooking
Instruction manual
Part number: 070116
Page 2
Dear Customer,
Your new Defy appliance was manufactured in a state of the art facility and has passed the strictest quality control
procedures.
Important: Read these instructions for use carefully so as to familiarize yourself with the appliance before
connecting it to its gas container. Keep these instructions for future reference.
This User Manual may also be applicable for several other models. Differences between models are explicitly
identified in the manual.This manual will provide you with information on how to operate and care for your
appliance to gain the maximum benefit from it.
We trust you will enjoy years of trouble free use.
EXPLANATION OF SYMBOLS
Throughout this User Manual the following symbols are used:
Important information or useful hints about usage.
Warning for hazardous situations with regard to life and property.
Warning for risk of fire.
Warning for hot surfaces.
Table of contents
1 General information 3
Overview 3
Technical specifications 3
Identification table 4
2 Important safety instructions 5
General safety 5
Safety for children 6
Safety when working with gas 7
If you smell gas 8
Action to be taken in event of a burn back 8
Intended use 9
Anti tilt mechanism 10
3 Installation 11
Before installation 11
Room ventilation 11
Important information 13
Installation and connection 13
Leakage control 14
Final check 14
Gas conversion 14
Package information 17
Future transportation 17
Disposing of the old appliance 17
4 Preparation 16
Tips for energy saving 16
First cleaning of the appliance 16
Initial heating 16
Oven 16
5 Using the hob 17
General information about cooking 17
Using the hobs 17
6 How to operate the oven 18
General information on baking & roasting 18
How to use the oven 18
Cooking times table 19
7 Maintenance and care 20
General information 20
Cleaning the hob 20
Cleaning the oven / oven door 21
Removal of the oven door 21
Gas jet cleaning procedure 21
8 Troubleshooting 22
9 Branches 23
10 Warranty 24
Page 3
1 General Information
Overview
Technical specifications
GENERAL
External dimensions (height / width / depth) 850 mm/500 mm/600 mm
Gas type / pressure LPG - G 30/2.8-3.0 kPa
Total gas consumption 6.0 kW
HOB
Burners
Rear left Solid plate
Power 1000 W
Front left Rapid burner
Power 2500 W
Front right Auxiliary burner
Power 1000 W
Rear right Normal burner
Power 2000 W
OVEN/GRILL
Main oven Static oven
Power consumption of oven 2.6 kW
1 Burner plate
2 Control panel
3 Wire shelf
4 Front door
5 Lower part
1
2
3
4
5
1 Oven Thermostat
2 Selector
3 Solid plate rear left
4 Rapid burner front left
5 Auxiliary burner front right
6 Normal burner rear right
7 Ignition switch
8 Indicator light
PERMIT NUMBER
1037-57/1-RSA-12-A
Page 4
User manual
Technical specifications may be changed
without prior notice to improve the quality
of the appliance.
Figures in this manual are schematic and
may not match your appliance exactly.
Values stated on the appliance labels or
in the documentation accompanying it
are obtained in laboratory conditions in
accordance with relevant standards.
Depending on operational and
environmental conditions of the
appliance, these values may vary.
The manufacturer strives for continuous
improvement. For this reason, technical
specifications, text and illustrations in this
manual are subject to change without
notice.
Wire Shelf
Used for roasting and for placing food to be baked,
roasted or cooked in casserole dishes on to the
desired rack.
Identification table
Position hob zone 1000 W
Rear left
(RL)
2500 W
Front left (FL)
1000 W
Front right (FR)
2000 W
Rear right (RR)
Gas type / Gas pressure
LPG - G 30/2.8-3.0 kPa - 80 50 72
Rear left (RL)
Front left (FL)
Rear right (RR)
Front right (FR)
Burner Type Wattage Recommended Cooking Vessel Size
Auxilliary Burner (FR) 1000 12 – 14 cm
Normal Burner (RR) 2000 18 – 20 cm
Normal Burner (RL) 2000 18 – 20 cm
Rapid Burner (FL) 3000 20 – 22 cm
Important cooking information table
Accessories supplied may vary
depending on the model. Not all
accessories in the user manual
may be included with your
appliance. Accessories may be
purchased from Defy spares.
Page 5
2 Important safety instructions
This section contains safety
instructions that will help you
avoid risk of injury and damage.
All warranties will become void if
instructions are not followed.
General safety
x This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning the use
of the appliance by a person
responsible for their safety.
x Children should be supervised
to ensure that they do not play
with the appliance.
x Do not operate the appliance if
it is defective or has any visible
damage.
x Do not carry out any repairs or
modifications on the appliance.
However, some issues may
remedied that do not require
any repairs or modifications.
See Troubleshooting.
x Never use the appliance when
your judgment or coordination is
impaired by the use of alcohol
and/or drugs.
x Keep all ventilation slots clear
of obstructions.
x Do not use the appliance with
the front door glass removed or
cracked.
x Be careful when using alcoholic
drinks in your dishes. Alcohol
evaporates at high
temperatures and may cause a
fire since it can ignite when it
comes into contact with hot
surfaces.
x Do not heat closed tins and
glass jars in the oven. The
pressure that would build up in
the tin/jar may cause it to burst.
x Do not place any flammable
materials close to the appliance
as the sides may become hot
during use.
x Do not place baking trays,
dishes or aluminium foil directly
onto the bottom of the oven.
The heat accumulation might
damage the bottom of the oven.
x The appliance may be hot when
it is in use. Never touch the hot
burners, inner sections of the
oven, heaters etc.
x Always use heat resistant oven
gloves when putting in or
removing dishes from the hot
oven.
x Make sure that the function
knobs are switched off after
every use.
x Always keep children and infirm
persons away from the
appliance when it is in use.
x Do not use or store inflammable
products (alcohol, petrol,
benzene etc.) near the
appliance as these pose a fire
risk.
Page 6
x Electrical and/or gas products
are dangerous to children. Keep
children away from the
appliance when it is operating
and do not allow them to play
with the appliance.
x Accessible parts of the
appliance will become hot whilst
the appliance is in use. Children
must be kept away until the
appliance has cooled down.
x "CAUTION: Accessible parts
may be hot when the grill is in
use. Young children should be
kept away."
x When the door is open, do not
load any heavy object on it and
do not allow children to sit on it.
It may overturn or the door
hinges may be damaged.
x The packaging materials are a
danger for children. Keep the
packaging materials away from
children. Please ensure that the
packaging material is disposed
of in a responsible manner.
x The rear surface of the oven
gets hot when it is in use. Make
sure that the gas connection
does not come into contact with
the rear surface as connections
may get damaged.
x When using Gas, ensure that
the room is well ventilated.
x Ventilation is vital for the
efficient performance of all
appliances and for the safety of
the occupants of the room in
which the appliance is installed.
x Use a deep pan, large enough
to cover the appropriate burner.
x Always dry food properly before
placing it in hot oil or fat. Frozen
food in particular will spit and
splatter if added too quickly.
x Never fill the pan more than one
third full of fat or oil.
x Never heat fat or fry with a lid
on the pan.
x Do not fry too much food at
once. This lowers the
temperature of the oil or fat and
results in fatty foods.
x Do not leave hot fat or oil
unattended. If overheating
occurs, these could catch fire.
Safety for children
x Packaging materials are
dangerous to children. Keep
packaging materials in a safe
place out of reach of children.
x Do not place any items above
the appliance that children may
reach for.
Safety when working with gas
x Any work carried out on gas
equipment and systems may
only be done by authorised
qualified persons who are
registered LPG Gas installers.
x Prior to installation, ensure that
the local distribution conditions
(nature of the gas and gas
pressure) and the adjustment of
the appliance are compatible.
x Installation and connection
must be in accordance with
current installation regulations.
Page 7
DANGER. Risk of
explosion and poisoning!
Put out all naked flames
and do not smoke, strike
matches or do anything
that could cause ignition.
Do not operate any
electric switches (e.g.
light switch, TV,
computer, cooker or door
bell). Do not use a
telephone or mobile
phone.
CAUTION: The use of gas
cooking appliances results in the
production of heat and moisture
in the room in which it is installed.
Ensure that the kitchen is well
ventilated: keep natural
ventilation holes open or install a
mechanical ventilation device
(mechanical extractor hood).
Prolonged intensive use of the
appliance may call for additional
ventilation, for example
increasing the level of the
mechanical ventilation where
present.
IMPORTANT: If the gas
type of the appliance is
changed, then the rating
plate that shows the gas
type of the unit must also
be changed.
IMPORTANT: If the gas
type of the appliance is
changed, then the
sticker that is currently
on the rear of the
appliance that reads
“Factory adjusted for
LPG gas” must be
replaced by the sticker
“Adjusted for natural
gas”. The new sticker is
in the gas jet kit supplied
with the appliance.
x Particular attention must be
given to relevant requirements
regarding ventilation; See
Before installation.
x Gas appliances and systems
must be regularly checked for
proper functioning. The
regulator, hose and its clamp
must be checked regularly and
replaced within the periods
recommended by its
manufacturer or when
necessary.
x Clean the gas burners regularly.
The flames should be blue and
burn evenly.
x Good combustion is required in
gas appliances. In case of
incomplete combustion, carbon
monoxide (CO) might develop.
Carbon monoxide is a
colourless, odourless and very
toxic gas, which has a lethal
effect even in very small doses.
x Request information about gas
emergency telephone numbers
and safety measures from your
local gas provider in case of a
gas smell .
Page 8
In the event of a pan fire
x Switch off the Gas supply.
x Smother the flames with a
blanket or damp cloth.
x Burns and injuries are usually
caused by picking up the
burning pan and rushing
outside with it.
x Do NOT use water to extinguish
an oil or fat fire.
Intended use
This appliance is designed for
domestic use. Commercial use
will void the warrantee.
CAUTION: This appliance is for
cooking purposes only. It must
not be used for other purposes.
This appliance must not be used
for warming plates under the grill,
drying towels, dish cloths etc. by
hanging them on the oven door
handles. This product should also
not be used for room heating
purposes. The manufacturer shall
not be liable for any damage
caused by improper use or
handling errors.
Ventilation
x Room ventilation is vital for the
efficient performance of the
appliance and for the safety of
the occupants in the room in
which the appliance is installed.
Action to be taken in the event
of a burn back
x In the event of a burn back
(where the flame burns back
into the jet ) immediately turn
off the control to the affected
burner.
x Wait a few minutes and relight
the burner in the normal
manner.
x If the burn back occurs again,
turn off the control knob to the
affected burner, and consult the
nearest Defy service
technician, who will advise you.
If you smell gas
x Turn off all valves on gas
appliances and gas meter at
the main control valve, unless
it's in a confined space or
cellar.
x Extinguish all naked flames.
x Do not operate any electrical
appliances.
x Ventilate the area. Open doors
and windows.
x Check for leaks. Check all
tubes and connections for
tightness.
x If odour persists contact your
nearest Defy Service Centre for
assistance.
x If you still smell gas leave the
property.
x Warn the neighbors.
x Call the fire-brigade. Use a
telephone outside the house.
x If you have door or gates that
are secured by an electric lock,
or entry phone, please open
these manually.
x Do not re-enter the property
until you are told it is safe to do
so.
Page 9
Oven flame failure
safety cut out. (Oven
only) In the unlikely event
of a flame blow out,
caused by an overflow of
fluid at the oven burner, a
safety mechanism will
automatically shut off the
gas to the oven
approximately 30
seconds after the flame
extinguishes.
Electrical safety
x If the appliance has a failure, it
should not be operated unless it
is repaired by an authorized
service agent. There is a risk of
an electric shock!
x Connect the appliance to an
earthed outlet/line protected by
a fuse of suitable capacity.
Have the earth installation
made by a qualified electrician.
This appliance must be earthed
and the manufacturer and the
seller do not accept
responsibility for any damage
due to incorrect installation or
electrical connection.
x The appliance must be
disconnected from the mains
during installation,
maintenance, cleaning and
repair procedures.
x Never wash down the appliance
with water! There is the risk of
electric shock!
x The appliance must be installed
so that it can be completely
disconnected from the network.
The separation must be
provided either by a mains plug,
or a switch built into the fixed
electrical installation according
to construction regulations.
x If the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
x The rear surface of the stove
gets hot when it is in use.
Ensure that the electrical
connection does not come into
contact with the rear surface so
as not to damage connections.
x Do not trap the mains cable
between the oven door and
frame, do not route it over hot
surfaces as the cable insulation
may melt and cause a fire as a
result of a short circuit.
x Any work on electrical
equipment and systems to only
be carried out by authorized
and qualified persons.
x Where the appliance is
intended to be permanently
installed, the installation shall
only be carried out by a
registered installer and that
such installations shall comply
with the requirements of SANS
10087-1or SANS827 as
applicable.
SAVE THESE INSTRUCTIONS
Page 10
Anti-tilt mechanism
All stoves can tilt if you or a child
sit or lean on an open oven door.
x “A” 1 x Stability chain
x “B” 1 x Stability hook with
anchor sleeve
x “A” is factory fitted at the
rear of the stove in the centre.
(See overleaf for instructions if
the removable splashback is to
be fitted)
x Position the stove and move
“A” to touch the wall behind
the stove.
x Mark the hole where A
touches the wall behind the
stove.
x Move the stove away from the
wall to allow for an area to work
in.
x Using a 8.0 mm concrete bit,
drill a hole at the marked
position.
WARNING: in order to
prevent tipping of the
appliance, this stabilizing
means must be installed.
Refer to the instruction for
installation.
x Using the Stability hook and
anchor sleeve “B”, firmly secure
“B” to the wall.
x Slide the stove back in position
and engage the stability chain
“A” onto stability hook “B”.
x The stove is then secured and
will not accidentally tilt if
downward pressure is applied
to the open oven door.
Page 11
3 Installation
Installation is the buyer’s responsibility. The
manufacturer accepts no liability for this service. Any
action that the manufacturer has to take as a result of
an erroneous installation will not be covered by the
warranty.
The necessary installation, including gas and
electrical connections, must be carried out by
qualified personnel in accordance with current and
local regulations. An installation by an unqualified
person may constitute a hazard.
Installations carried out by unauthorized persons will
void the warranty.
The manufacturer shall not be held responsible
for injury to persons or damages arising from
procedures carried out by unauthorized persons
or due to non compliance with these provisions.
Preparation of location, electrical and
gas installation for the appliance falls
under the customer’s responsibility.
DANGER The appliance must be
installed in accordance with all local
gas and/or electrical regulations.
DANGER Prior to installation,
visually check if the appliance has any
defects on it. If so, do not have it
installed. Damaged appliances are a
safety risk.
x The appliance can be used with cabinets on either
side but in order to have a minimum distance of
400mm above hotplate level allow a side
clearance of 65mm between the appliance and
any wall, partition or tall cupboard.
x The appliance can also be used in a free standing
position. Allow a minimum distance of 750 mm
above the hob surface.
x (*) If a cooker hood is to be installed above the
cooker, refer to cooker hood manufacturer
instructions regarding installation height (min 650
mm).
x The appliance corresponds to device class 1, i.e. it
may be placed with the rear and one side to
kitchen walls, kitchen furniture or equipment of any
size. The kitchen furniture or equipment on the
other side may only be of the same size or
smaller.
x Any kitchen furniture next to the appliance must be
heat-resistant (100 °C min.).
Before installation
To ensure that critical air gaps are maintained under
the appliance, we recommend that this appliance is
mounted on a solid base and that the feet do not sink
into any carpet or soft flooring.
The kitchen floor must be able to carry the weight of
the appliance plus the additional weight of cookware,
bakeware and food.
This appliance requires an operating pressure of
2.8-3.0 kPa. A suitable LPG regulator that
complies with the requirements of SANS 1237
must be used.
The manufacturer and the seller do not accept
responsibility for any damage due to incorrect
installation or gas connection.
Gas bottles should be located outdoors in a suitable
ventilated lock-up.
The connecting hose should not exceed 200 cm in
length.
Room ventilation
All rooms require a window that can be opened, or
equivalent, and some rooms will require a permanent
vent in addition.
Air for combustion is drawn from the room and the
exhaust gases are emitted directly into the room,
therefore good room ventilation is essential for the
safe operation of your appliance. If there is no window
or door available for room ventilation, extra ventilation
must be installed.
The appliance may be located in a kitchen, kitchen/
diner or a bed-sitting room, but not in a room
containing a bath or shower. The appliance must not
be installed in a bed sitting room of less than 20m3.
Do not install this appliance in a room below ground
level unless it is open to ground level on at least one
side.
This appliance uses LPG (Liquid petroleum or
bottle gas).
LPG Gas Only: Do not install this
appliance in a room below ground level
unless it is open to ground level on at
least one side. Failure to install
appliances correctly is dangerous and
could lead to prosecution.
Page 12
Electrical installation
This appliance must be earthed and the
manufacturer and the seller do not accept
responsibility for any damage due to incorrect
installation or electrical connection. This appliance
should not be connected through an earth leakage
system. Refer to S.A.N.S. 10142
Connection to the power supply
This appliance has a ‘Y’ type supply cord connection
and must be installed by a licensed electrician, who
will ensure that the stove is correctly connected and
safely earthed. The rated current is printed on the
serial number label attached to the stove upper back
panel. The appliance must be connected to the mains
through an All pole isolating switch which has a
minimum clearance between the contacts of 3 mm. in
All poles. A means for disconnection must be
provided in the fixed wiring.
Electrical installation
Push the electric plug into a 230V. 15A. Earthed
wall socket The stove is a plug in model with a 15A.
power supply. Do not set the knob to the unmarked
position.
Connecting the sprague to the oven
1.) Purchase a standard plastic/metal saddle type
bracket, capable of going around the 20 mm
diameter sprague and with a hole pitch of 38 mm
(Plastic) 45 mm (Metal), from your local hardware
and 2 off 4.2 mm x 12 mm self tapping screws.
2.) Feed the cables through the Sprague and connect
to the mains terminal block of the appliance.
3.) Place the plastic/metal saddle around the sprague
and fasten via the 2 self tapping screws onto the
factory pre punched holes adjacent to the mains
terminal block of the appliance.
1 2
3
WARNING!
Electrical
connection
must only
be done by
a qualified
electrician.
Cleaning: Do not use a steam cleaner.
Cleaning the Exterior
x Switch off the electrical supply to the stove before
cleaning any part of it
x Use a damp soapy cloth and avoid the use of
abrasive powders and scouring pads.
Caring for solid plates
x To prevent blotchy discolouration and corrosion,
moisture from spatters and spills should be
cleaned off immediately.
x To clean the plate, wipe it with a damp cloth or
nylon pad. A little liquid detergent may be used.
Do not use metal scourers or sharp metal objects
to clean the plate.
x After cleaning, dry the plate by switching it on for a
short while.
x To prevent rust, periodically apply some, sewing
machine oil or electrical hotplate polish - available
from Defy Service Centres. Extra attention is
required in areas of high humidity or in close
proximity to the sea.
Switch off the power at the mains
in the event of a fault or when
cleaning the appliance.
Cleaning the Oven
x Use a hot, soapy damp cloth to clean any part of
the oven. Stubborn stains may require the use of a
nylon scrubbing brush and a liquid cleaner. Do not
use metal scouring pads or abrasive cleaners.
Recommendations
x Use only pots with a solid level base. An uneven
base can prolong cooking times and waste
energy.
x Use pots with a base diameter slightly larger than
the plate. This will ensure even heat distribution
and prevent spillage from dripping onto and
staining the hot plate.
x Always cover the pot with a lid. This will conserve
energy and minimise spillage.
x Thermal shock could damage the plates. Do not
put cold pots on very hot plates.
Note
x The warranty does not cover the replacement or
repair of rusted or corroded solid plates. It is
therefore the owners responsibility to care for them
as described above.
Element and guard
x After cleaning the oven, ensure that the oven
element is securely clipped into the hook of the
element guard. Failure to observe this precaution
will allow the element to rest on and damage the
oven enamel.
Page 13
Installation and connection
This appliance can only be installed and connected in
accordance with the statutory installation rules.
Room size Ventilation
opening
Smaller than 5 m3 min. 100 cm2
5 m3 to 10 m3 min. 50 cm2
Greater than 10 m3 not required
In the cellar or basement min. 65 cm2
Important information
Upon completion of the installation ensure that you
are familiar with the following:
a) The position of the isolation or shut-off valve in the
gas supply line to the appliance.
b) The requirements for safe operation of the
appliance
Note.This appliance is supplied ex-factory with
jets and air settings for use with LPG gas only.
Safety compliance with local requirements:
Installation
A stove without a flame failure device may only be
used with a free standing cylinder placed adjacent
to but not closer to 300 mm to the stove.
Ensure that pipe clamps are tightened correctly and
are of a good quality.
x Flexible hose
Any hose that is used to connect the stove to the
gas system shall comply with SANS 1156-2 or BS
3212.
x Gas cylinder - Not supplied.
For best results we recommend that gas cylinders
with a minimum capacity of 9kg be used.
x Regulator - Not supplied.
A 2.8-3.0 kPa LPG gas regulator which complies
with SANS 1237 must be used.
Failure to comply with the above will render the
warranty invalid.
Note:
Your invoice is required in the event of you
wishing to make a warranty claim.
Gas connection
DANGER Risk of explosion or
poisoning by unprofessional
installation.
The appliance may be connected to
the gas distribution system only by a
registered LPG installer.
DANGER Risk of explosion!
Before starting any work on the gas
installation, please shut off the gas
supply.
x Gas adjustment conditions and values are stated
on labels (or on type label).
Your appliance is adjusted for LPG gas.
A stove without a flame failure device
may only be used with a free standing
cylinder placed adjacent to but not
closer to 300 mm to the stove.
Do not install the appliance next to
refrigerators or freezers. The heat
emitted by the appliance will lead to an
increased energy consumption of cooling
appliances.
Carry the appliance with at least two persons. The
appliance must be placed directly on the floor. It must
not be placed onto a base or a pedestal.
Material damage!
The door and/or handle must not be
used for lifting or moving the appliance.
Gas regulator - Not supplied.
Range – 2.8 KPA SA5 regulator with a 2 meter hose
and 2 hose clamps.
Connecting the gas hose
x Have your appliance connected so that it will be
close to the gas connection. Ensure that there is
no gas leakage.
x Gas bottles should be located outdoors in a
suitable ventilated lock-up.
x The connecting hose to be used must not be
longer than 200 cm in length.
x Fit the clamp to the hose. Soak one end of the
hose (15 mm inner diameter) into hot water for 60
seconds to soften, then slip the softened end of
the hose completely onto the sharp hose tip of the
appliance.
Page 14
x Secure the hose by tightening the hose clamp.
x Repeat the same procedure for the other end of
the hose by securing it to the regulator on the gas
bottle to complete the gas cylinder connection.
x Always check for gas leaks after installation and
whenever a new or refilled gas bottle is used for
the first time.
Leakage control at the connection point
x Ensure that the control knobs on the control panel
are in the OFF position.
x Open the valve on the Gas bottle.
x Using a small paint brush, apply some soapy
water to all the connections.
x If there is a leak, bubbles will appear.
x If this occurs, close the gas bottle valve .
x Check and tighten the connections immediately.
x Repeat the procedure to ensure that there are no
further leaks.
1. Hose tip-LPG
2. Hose tip-NG
3. Safety hose
4. O-ring (gasket)
5. Clamp
x Push the appliance towards the kitchen wall.
Caution: Never use a naked flame to
check for gas leaks.
DANGER Risk of explosion by
damage of the safety tube!
The safety tube must not be clamped,
bent or trapped or come into contact
with hot parts of the appliance.
DANGER Risk of explosion and
suffocation! LPG bottles must not be
stored in the house.
Final check
1. Open gas supply.
2. Check gas installations for secure fitting and
tightness.
3. Ignite burners and check appearance of the flame.
Gas conversion
In order to have the appliance's gas type changed, all
the injectors must be changed and the flame
adjustment for all valves must be set at the reduced
flow rate position.
Changing the injectors
1. Take off burner cap and burner body.
2. Unscrew injectors by turning them
counterclockwise.
3. Fit new injectors.
4. Check all connections for secure fitting and
The flames should be blue and burn
smoothly. If the flames appear
yellowish, check that the burner cap is
seated correctly or clean the burner.
Switch off the gas and let burner cool
before touching it.
DANGER Risk of explosion or
poisoning by unprofessional
installation. Gas conversion must
only be carried out by a registered
installer.
DANGER Risk of explosion!
Before starting any work on the gas
installation, shut off the gas supply.
Manifold
protection
plug
Manifold protector plug removal:
The manifold protection plug is inserted into the
manifold at factory level in order to protect the
manifold from being contaminated with debris. The
manifold protection plug must be removed when the
product is installed by the gas installer.
The red manifold protection plug can be removed
from the manifold by grabbing it with your fingers or if
necessary with the aid of a small pair of pliers.
Manifold
1 Flame failure device (model dependent)
2 Spark plug
3 Injector
4 Burner
Page 15
Unless there is an abnormal condition,
do not attempt to remove the gas burner
taps. You must call an authorised
service agent if it is necessary to
change the taps.
New injectors have their position
marked on their packing or refer to the
Injector table.
Reduced gas flow rate setting for taps
1. Ignite the burner that is to be adjusted and turn the
knob to the reduced position.
2. Remove the knob from the gas tap.
3. Use an appropriately sized screwdriver to adjust
the flow rate adjustment screw. For LPG (Butane -
Propane) turn the screw clockwise. For natural
gas, you should turn the screw counter-clockwise
once. The normal length of a straight flame in the
reduced position should be 6-7 mm
4. If the flame is higher than the desired position, turn
the screw clockwise. If it is smaller turn
anticlockwise.
5. For the last control, bring the burner to both the
high-flame and reduced positions and check
whether the flame is on or off.
Depending on the type of gas tap used in your
appliance the adjustment screw position may vary.
If the gas type of the appliance is
changed, then the rating plate that
shows the gas type of the unit must also
be changed.
Exchange of injector for the oven
1. Unscrew the fastening screws of the back wall.
2. Unscrew the 2 screws (2) of the injector holder (1).
1. Injector holder
2. Screw
3. Pull out the injector holder.
4. Unscrew injector by turning to counter-clockwise
direction.
5. Fit new injector.
2. Close the oven door and wait for 10 to 15 minutes
until the oven becomes ready for adjustment.
3. Take out the knob
4. After 15 minutes, adjust the oven to the lowest
flame position.
5. Set the flame length to 2 to 3 mm by adjusting the
screw 1 on the oven tap. Turn clockwise to reduce the
flame, turn counter-clockwise to increase the flame.
If the temperature of the oven increases
unintentionally, turn off the oven and
call the authorised service agent to
have the oven thermostat repaired.
Butan/propan Natural gas
Fasten the screw
until the end
Loosen the
screw
1/2 round
1 Flow rate adjustment screw
Before connecting the gas hose, make sure that the
gas hose outlet behind the product is in the same
direction as the hose outlet
If the gas hose is not in the same direction as the
hose outlet, mount it so that it does not pass through
the hot zone when connecting the hose.
3
3
X
X
X
Routing of the gas hose
Reduced flow adjustment for the gas oven
For the appropriate functioning of the oven re-
checking the by-pass adjustment is extremely
important. In order to provide maximum security to
the user these operations have to be done with care.
1. Ignite the burner that is to be adjusted and turn the
knob to the high flame position.
Page 16
Check the general appearance of your
appliance for any damages that might
have occurred during transportation.
Do not place other items on the top of
the appliance. The appliance must be
transported upright.
Disposing of the old appliance
Dispose of the old appliance in an environmentally
friendly and safe manner.
Refer to your local dealer or solid waste collection
centre in your area to learn how to dispose of your
product.
Before disposing of the product, make the door lock
(if any) unusable to avoid dangerous conditions to
children.
4 Preparation
Tips for energy saving
The following information will help you to use your
appliance in an ecological way, and to save energy:
x Use dark coloured or enamel coated cookware in
the oven for better heat transmission.
x Before cooking your dishes, perform a preheating
operation if it is advised in the user manual or
cooking instructions.
x Do not open the door of the oven frequently during
cooking.
x Try to cook more than one dish in the oven at the
same time whenever possible. Two cooking
vessels can be placed onto the wire shelf.
First cleaning of the appliance
The surface of the appliance may be
damaged by some detergents or
cleaning materials. Do not use
aggressive detergents, cleaning
powder, cream or any sharp objects.
1. Remove all packaging materials.
2. Wipe the surfaces of the appliance with a damp
cloth or sponge and dry with a cloth.
Initial heating
Heat up the appliance for about 30 minutes and then
switch it off. This will ensure that any production
residues or layers will be burnt off and removed.
WARNING Hot surfaces cause
burns! Product may be hot when it is in
use. Never touch the hot burners, inner
sections of the oven, heaters and etc.
Keep children away. Always use heat
resistant oven gloves when putting in
or removing dishes into/from the hot
oven.
Package information
Packaging materials are dangerous to children. Keep
packaging materials in a safe place out of reach of
children.
Packaging materials of the appliance are
manufactured from recyclable materials.
Do not dispose of the packaging materials together
with domestic or other wastes. Dispose of them in a
responsible manner.
Future Transportation
Keep the appliances original carton and transport the
appliance in it. Follow the instructions on the carton. If
you do not have the original carton, pack the
appliance in bubble wrap or thick cardboard and tape
it securely.
To prevent the wire grill and tray inside the oven from
damaging the oven door, place a strip of cardboard
onto the inside of the oven door that lines up with the
position of the trays. Tape the oven door to the side
walls.
Secure the caps and pan supports with adhesive
tape.
Do not use the door or handle to lift or move the
appliance.
Smell and smoke may emit during the
first heating. This is not a fault and is
quite normal and is due to any
production residues or layers being
burnt off and removed. Ensure that the
room is well ventilated.
x Cook more than one dish one after another. The
oven will already be hot.
x Save energy by switching off your oven a few
minutes before the end of the cooking time. Do not
open the oven door.
x Defrost frozen dishes before cooking them.
x Use pots and pans with covers for cooking. If there
is no cover, energy consumption may increase by 4
times.
x Select the burner which is suitable for the bottom
size of the pot that is to be used. Always select the
correct pot size for your dishes. Larger pots require
more energy.
Danger of fire: Do not store items on the
cooking surface.
CAUTION: The cooking process has
to be supervised. A short term cooking
process has to be supervised
continuously.
WARNING: Unattended cooking on a
hob with fat or oil can be dangerous and
may result in a fire.
Page 17
5 Using the hob
Important! See cooking information table on page 4
for cooking vessel sizes. The large flame symbol
indicates the highest cooking power and small flame
symbol indicates the lowest cooking power. In the
turned off position (top), gas is not supplied to the
burners.
Igniting the gas burners
Burner is equipped with automatic ignition.
1.Keep the burner knob pressed in.
2.Turn it counter clockwise to the large flame symbol.
3.Ignite the hob by pressing the automatic ignition
switch on the right hand side of the control panel.
4.Adjust it to the desired cooking power.
Turning off the gas burners
Turn the knob to off (upper) position.
Using the hobs
IGNITION ELECTRODE
FLAME
FAILURE
SENSOR
General information about cooking
DANGER Risk of fire by overheated
oil! When heating oil, do not leave it
unattended.
Never try to extinguish a fire with
water! When oil has caught fire,
immediately cover the pot or pan with a
lid. Switch off the hob if safe to do so
and phone the fire service.
x Before frying foods, always dry them well and
gently place into the hot oil. Ensure complete
thawing of frozen foods before frying.
x Do not cover the pot or pan being used when
heating oil.
x Place the pans and saucepans in a manner so that
their handles are not over the hob to prevent
heating of the handles. Do not place unbalanced
and easily tilting cooking vessels on the hob.
x Do not place empty pots or saucepans on cooking
zones that are switched on. to prevent damage.
x Operating a cooking zone without a pot, pan or
saucepan on it may damage the appliance. Turn off
the cooking zones after cooking is complete.
x As the surface of the appliance can be hot, do not
place plastic and aluminum vessels on it.
x Plastic and aluminum vessels should not be used
to keep foods in.
x Use flat bottomed saucepans or cooking vessels.
x Place only the appropriate amount of food in
saucepans and pans. Doing so will assist with not
having to do any unnecessary cleaning as this will
help prevent the dishes from overflowing.
x Do not put covers of saucepans or pans on the
cooking zones.
x Place saucepans so that they are centered on the
cooking zone. When moving the saucepan onto
another cooking zone, lift and place it onto the
other cooking zone instead of sliding it.
Gas cooking
x The size of the cooking vessel and the flame must
be suited to each other. Adjust the gas flames so
that they do not extend past the bottom of the
cooking vessel and ensure that the cooking vessel
is centered on the saucepan carrier.
Fitting the burner caps
Incorrect Correct
x Carefully align the hole in the burner body with the
flame failure sensor.
x Gently lower the burner body into position.
x Centralise and level the burner cap onto the
burner body. (The burner cap must be positioned
so that it rests centrally on the burner body).
Ensure that it is correctly seated. Refit the pot
stands.
Page 18
WARNING: Hot surfaces may cause
burns! Do not touch the hot surfaces of
the appliance. Use oven gloves. Keep
children away from the appliance.
DANGER: Risk of scalding by hot
steam! Take care when opening the
oven door as steam may escape.
Tips for baking
x Use non-sticky coated appropriate metal plates or
aluminum vessels or heat resistant silicone
moulds.
x Make best use of the space on the rack.
x Place the baking mould in the middle of the shelf.
x Select the correct rack position before turning the
oven on. Do not change the rack position when the
oven is hot.
x Keep the oven door closed.
Tips for roasting
x Treating whole chicken, turkey and large pieces of
meat with dressings such as lemon juice and black
pepper before cooking will increase the cooking
performance.
x It takes about 15 to 30 minutes longer to roast
meat with bones when compared to roasting the
same size of meat without bones.
x Each centimeter of meat thickness requires
approximately 4 to 5 minutes of cooking time.
x Let meat rest in the oven for about 10 minutes
after the cooking time is over. The juice is better
distributed all over the roast and does not run out
when the meat is cut.
x Fish should be placed on the middle or lower rack
in a heat-resistant plate.
General information on baking & roasting
6 How to operate the oven
Closed vessels will preserve the juice of the dish. If a
vegetable dish does not get cooked, boil the
vegetables beforehand or prepare them like canned
food and put in the oven.
Tips for cooking vegetables
If the vegetable dish runs out of juice and gets too
dry, cook it in a pan with a lid instead of a tray.
Shelf positions
x BAKE is used for baking and roasting
x PRE-HEAT utilises all the oven elements to
quickly bring the oven up to the selected
temperature. The oven indicator light will remain
on until the selected temperature is reached
Thereafter the selector must be set to BAKE . You
may use the oven without PRE-HEAT, it just takes
a little longer to warm up.
x GRILL is used for conventional grilling
Grilling
x Keep oven door closed during grilling.
x Set the selector to grill and the oven thermostat to
the grill position.
x Place oven shelf on the top shelf position.
x Place the item to be grilled in a roast pan on the
shelf under the pre-heated grill element.
x The oven door may be opened to check on the
grilling process which should be done every 5 to
10 minutes to avoid burning the food.
x After grilling is completed, the oven thermostat and
the selector switch must be returned to the "0"
position in an anti-clockwise direction.
4 Position selector
x The selector is used to select one of four oven
operating modes.
1. 0 or OFF,
2. Bake
3. Pre-Heat
4. Grill
WARNING:
Accessible parts may become hot
when grilling.
Always use oven gloves when handling
food in the oven and keep children well
away from the stove when it is in use.
Page 19
Cooking times table
1st rack of the oven is the bottom rack.
Maximum load capacity of oven tray:
4 kg (8.8 lb).
The timings in this chart are meant as a
guide. Timings may vary due to
temperature of food, thickness, type
and your own preference of cooking.
Stand dishes on a baking sheet to prevent spillages
onto oven base and help keep oven clean.
Food Preheating * Insertion
level Temp Cooking
time
Apple
pie 10 min. 3...4 180 30...40 min.
Fruit tart 10 min. 3...4 180 30...40 min.
Pie 10 min. 3...4 180 40...55 min.
Cookies 10 min. 3...4 180 30...40 min.
Pastry 10 min. 3...4 180 30...40 min.
Cake 10 min. 2 180 40...55 min.
Biscuits 3...4 180 30...40 min.
Roast
lamb 10 min. 3...4 240
30...40 min.
per 450 g +
30 min.
Roast
Beef 10 min. 2...3 240
30...40 min.
per 450 g +
30 min.
Turkey 10 min. 4...5 240
50...60 min.
per 450 g +
30 min.
Poultry 10 min. 2...3 240
30...40 min.
per 450 g +
25 min.
Casserol 4 240 90...120 min.
§
Fish 10 min. 2 240 30...40 min.
Macaroni 10 min. 3 240 20 min.
Small
cakes 10 min. 2 180 35...40 min.
Victoria
sand-
wich
10 min. 3 180 30...35 min.
* at control knob position 270 / § depending on quantity / #
depending on size
Baking
For best baking results, use an aluminium bake
tray (300 x 230 x 30mm.) These are available from
all Defy Parts Centres Part number 067609.
Teflon coated baking trays are not recommended.
x Set the selector to pre-heat and set the oven
thermostat to the desired temperature.
x The indicator light will glow and remain on until the
oven has reached the selected temperature.
x When the indicator light switches off, the food
should be placed in the oven.
x Set the selector to bake
x During baking the indicator light will regularly cycle
on and off as the oven thermostat maintains the
selected temperature.
x The door may be opened, for inspection purposes,
after about half the cooking time has elapsed..
Solid plate
x Before using the plates for the first time, switch
them on for four minutes at the highest setting.
This allows the factory applied protective coating
to burn in.
x The markings around the plate control knobs
represent the following heat settings:
x 1 = Warming.
x 2 = Slow simmer.
x 3 = Simmer.
x 4 = Medium heat.
x 5 = High heat
x 6 = Boiling and frying.
Page 20
7 Maintenance and care
General information
The service life of the appliance will extend and the
possibility of problems will decrease if the appliance is
cleaned at regular intervals.
Service intervals
x Every twelve months the appliance should be
serviced by a Defy Service agent to ensure
continued efficient and safe operation.
x If required, the cleaning of the valves should only
be carried out by a qualified Defy technician. i.e.
Burner not functioning correctly.
x Wash removable burner parts weekly with hot
water and detergent.
x Remove any encrustations and ensure that the
burner holes are clear.
x The condition of the gas hose and valve should be
inspected for leaks every time the gas bottle is re-
filled.
DANGER Hot surfaces may cause
burns! Allow the appliance to cool
down before you clean it.
x Clean the appliance thoroughly after each use.
This enables cooking residues to be removed more
easily and prevents these from burning when the
appliance is used.
x No special cleaning agents are required for
cleaning the appliance. Use warm water with
washing liquid, a soft cloth or sponge to clean the
product and wipe it with a dry cloth.
The surface may be damaged by some
detergents or cleaning materials. Do not
use aggressive detergents, cleaning
powder/cream or any sharp objects.
Do not use steam cleaners for cleaning.
Cleaning the hob
Gas hobs
1. Remove and clean the saucepan carriers and
burner caps.
2. Clean the hob.
3. Install the burner caps and make sure that they
are seated correctly.
4. When installing the upper grills, pay attention to
place the saucepan carriers so that the burners
are centered.
Cleaning the control panel
Clean the control panel and knobs with a damp cloth
and wipe them dry.
x Always ensure any excess liquid is thoroughly
wiped off after cleaning and any spillage is
immediately wiped dry.
x Never use high-pressure steam equipment or a
water jet for cleaning.
x Do not use cleaning agents that contain acid or
chloride.
x Never use cleaning products containing abrasive
materials as these could damage the decorative
and informative paint applications.
x Remove the burners and wipe them with a thin
damp cloth or a non-abrasive sponge. Use a
neutral detergent. Dry afterward with a soft cloth
and blow away any residual water in the gas outlet
holes.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Defy DGS178 User manual

Category
Stoves
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI