Supermicro X10SL7-F Quick Reference Manual

Brand: Supermicro

Model: X10SL7-F

Type: Quick Reference Manual

UPERMICR

ContaCt InformatIon

MNL-1463-QRG Rev. 1.00

• www.supermicro.com(Email:[email protected])

• Manuals:http://www.supermicro.com/support/manuals

• Drivers&Utilities:ftp://ftp.supermicro.com

• Safety:http://www.supermicro.com/about/policies/safety_information.cfm

consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.

PaCkage Contents

X10sL7-f

QuICk referenCe guIde rev. 1.00

• One(1)SupermicroMotherboard

• Six(6)SATACables

• One(1)I/OShield

• One(1)QuickReferenceGuide

MNL-1463-QRG

Connector Description

Battery

Onboard Battery

COM1/COM2

COM1 (Port)/COM2 (Header)

Fan1 - Fan4, FanA

System/CPU Fan Headers

JF1

Front Panel Control Header

JL1

Chassis Intrusion Header

JLED1

Power LED Indicator Header

JPI

Power SMB (System Management Bus)

JPW1

24-pin ATX Main Power Connector (Required)

JPW2

+12V 8-pin CPU power Connector (Required)

JSD1

SATA DOM (Device_On_Module) Power Connector

JSTBY1

Standby Power Header

JTPM1

Trusted Platform Module/Port 80 Connector

LAN1/LAN2

Gigabit (RJ45) Ports (LAN1/2)

IPMI_LAN

IPMI_Dedicated LAN

I-SATA0/I-SATA1

(Intel PCH) Serial ATA (SATA 3.0) Ports 0/1 (6Gb/sec)

I-SATA 2 - I-SATA5

(Intel PCH) Serial ATA (SATA 2.0) Ports 2~5 (3Gb/sec)

L-SAS 0-7

SAS Connectors 0-7 (supported by the LSI 2308 SAS controller)

(PCH) Slot 5

PCI-Express 2.0 x4 in x8 Slot

(CPU) Slot 6

PCI-Express 3.0 x8 in x16 Slot

SPKR1

Internal Speaker/Buzzer

SW1

UID (Unit Identier) Switch

6-SGPIO 1/2

Serial_Link General Purpose I/O Headers 1/2 for SAS Connections

T-SGPIO 1/2

Serial_Link General Purpose I/O Headers 1/2 for SATA Connections

USB 2/3, 4/5

Backpanel USB 2.0 Ports 2/3, 4/5

USB 0,1 (3.0)

USB 3.0 Ports 0, 1 (USB 0: Type A Connector)

USB 8/9

Front Panel Accessible USB 2.0 Headers 8/9

VGA

Backpanel VGA Port

Jumpers, Connectors and LED Indicators

Back Panel I/O Connectors

Memory Support

Motherboard Layout and Features

Note: Item numbers are listed in counterclockwise order.

IPMI CODE

SAS CODE

BIOS

LICENSE

BAR CODE

MAC CODE

FAN2

FAN3

FAN1

FAN4

FANA

JBR1

JPL2

JPS1

JPUSB1

JPL1

JWD1

JLED1

JPB1

JPG1

JPME1

JPME2

J19

J18

LE3

LE5

LE4

JPW1

JPW2

J21

JI2C1

JI2C2

L-SAS0 L-SAS1

L-SAS2 L-SAS3

L-SAS4

L-SAS5

L-SAS6

JPI2C1

JTPM1

6-SGPIO1

T-SGPIO1

T-SGPIO2

JSD1

SPKR1

JBT1

SW1

CPU SLOT6 PCI-E 3.0 X8 (IN X 16)

USB1 (3.0)

USB0 (3.0)

COM2

USB8/9

_LAN

IPMI

VGA

COM1

LAN2

JL1

LAN1

DIMMB2

DIMMA2

USB4/5

CPU

JF1

USB2/3

I-SATA3

I-SATA4

I-SATA2

I-SATA1

I-SATA0

I-SATA5

PCH SLOT5 PCI-E 2.0 X4 (IN X 8)

DIMMB1

DIMMA1

JSTBY1

L-SAS7

6-SGPIO2

Battery

PCH

SAS

CTRL

LAN

CTRL

LAN

CTRL

BMC

X10SL7-F

Rev. 1.01

CPU1

BIOS

Front Panel CTRL

JOH1

LEDS2

LE6

Jumpers

CPU Installation

Note: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as drawings shown in this guide.

Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,

and LED indicators.

Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/

motherboard installation instructions.

= mounting hole

Heatsink Installation

Front Panel Control (JF1)

DIMM Memory Installation

Connectors

LED Indicators

Load Plate

Load Lever

North Center

Edge

South

Center Edge

Pin 1

CPU Properly

Installed

Load Lever Locked

into Place

Thermal Grease

Heatsink Fan

1. Push Down

2. Turn

Clockwise

to lock; Turn

Counter-

clockwise to

unlock

3. Connect Fan

Cables to onboard

Fan Headers

Tools Needed:

Pan Head #6 screws (8)

Standoff (If needed)

Jumper Description Default

JBT1

CMOS Clear (See Chpt. 2)

C1/JI

SMB to PCI-E Slots Pins 2-3 (Disabled)

JPG1

VGA Enable Pins 1-2 (Enabled)

JPL1/JPL2

LAN1/LAN2 Enable Pins 1-2 (Enabled)

JPME1

ME Recovery Pins 1-2 (Normal)

JPME2

Manufacture Mode Select Pins 1-2 (Normal)

JPS1

SAS Enable Pins 1-2 (Enabled)

JPUSB1

USB 4/5 Wake_up Enable Pins 1-2 (Enabled)

JWD1

Watch Dog Enable Pins 1-2 (Reset)

LED Description Color/State Status

LE3 Standby Power LED On: Power On

LE4 UID LED Blue (On): Unit Identied

LE5 BMC Heartbeat LED Green (Blinking): BMC Normal

LE6 Power Status LED Red: PWR Fail/Yellow: Standby PWR Active/Green: PWR On Normal

LEDS2 SAS LED Green (Blinking): SAS Active/Red (Solid On): SAS Error

The X10SL7-F supports up to 32GB of Unbuffered (UDIMM) DDR3 ECC

1600/1333 MHz in 4 memory slots. Populating these DIMM modules with a pair

of memory modules of the same type and same size will result in interleaved

memory, which will improve memory performance.

Memory Population Guidelines

Please follow the table below when populating the X10SL7-F.

DDR3 Unbuffered ECC (UDIMM) Memory

DIMM Slots per

Channel

DIMMs Populat-

ed per Channel

DIMM Type POR Speeds Ranks per DIMM (any

combination)

2 1 Unbuffered

DDR3

1333, 1600 Single Rank, Dual Rank

2 2 Unbuffered

DDR3

1333, 1600 Single Rank, Dual Rank

Channel A Slot1

Channel A Slot2

Channel B Slot1

Channel B Slot2

Towards the CPU

Towards the Edge of the Motherboard

Release Tabs

Notches

Power Button

OH/Fan Fail LED

NIC1 LED

Reset Button

HDD LED

Power LED

Reset

PWR

Vcc

Ground

1920

Vcc

Ground

NMI

Vcc

PWR Fail LED

NIC2 LED

COM1

USB 2 (2.0)

USB 3 (2.0)

IPMI_LAN

USB 4 (2.0)

USB 5 (2.0)

LAN1

LAN2

VGA

Supermicro X10SL7-F Quick Reference Manual

Supermicro X10SL7-F Quick Reference Manual

Supermicro X10SL7-F Quick Reference Manual

Related papers

Other documents