Hunter Fan 53214 Owner's manual
- Category
- Household fans
- Type
- Owner's manual
www.HunterFan.com
1.888.830.1326
PAGE
7
PAGE
10
PAGE
5
PAGE
6
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation
Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Wiring Canopy
Operation,
Maintenance & Cleaning
Troubleshooting
DownrodPreparation
Table of Contents
PAGE
12
PAGE
4
Mounting Options
PAGE
14
Blades Switch Housing Light Kit
PAGE
13
PAGE
15
PAGE
19
?
?
?
PAGE
21
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Remote Control
PAGE
17
1
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
M3543-01 • 02/11/16 • © Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
(76.2 cm)
from blade tip
to nearest wall
or obstruction
7 feet
(2.15 m)
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
for ceilings 8-10 feet
(2.4-3 meters) high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet (3 meters)
or higher
2
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
This product may cause interference to radio equipment and
should not be installed near maritime safety communications
equipment, ships at sea, or other critical navigation or
communications equipment operating between 0.45-30 MHz.
This device complies with Part 18 of the FCC Rules.
www.HunterFan.com
1.888.830.1326
Tools Needed (not included)
Ladder
Power Drill
(optional)
9/64 in. (.36 cm)
Drill Bit (optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
3
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
4
M3543-01 • 02/11/16 • © Hunter Fan Company
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches
Wall
but
NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
4
34
O
CEILING
WALL
OPTION
1
Standard
Mounting
OPTION
2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
www.HunterFan.com
1.888.830.1326
Ceiling Bracket
5
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
For angled ceilings, point
opening toward peak.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Make sure all four bumpers are
still attached.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill .36 cm (9/64
in.) pilot holes in support
structure to aid in securing
ceiling bracket with
hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
OFF
Turn Power
5
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.13261.888.830.1326
www.HunterFan.com
Preparation
D
I
S
C
A
R
D
K
E
E
P
!
Remove the shipping blocks from the
motor. Save the screws. They will be
needed for blade iron installation.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and save the screws.
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
6
M3543-01 • 02/11/16 • © Hunter Fan Company
1.888.830.1326
Downrod
www.HunterFan.com
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Longer
Downrod
for angled ceilings
or ceilings 10
feet (3 meters) or
higher
Shorter
Downrod
for fans installed
close to ceiling
Standard
Downrod
for ceilings 8-10 feet
(2.4-3 meters) high
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
Included
(pre-assembled)
7
M3543-01 • 02/11/16 • © Hunter Fan Company
KEEP!
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
The wires can be cut, but
leave at least 8 inches (20
centimeters) extending from
the top of the downrod.
Downrod (continued)
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
1.888.830.1326
www.HunterFan.com
8 inches (20 centimeters)
3/8 in.
.95 cm
8 in.
3/8 in.
C
U
T
&
S
T
R
I
P
(not to scale)
3/8 in.
.95 cm
8 in.
20 cm
8
M3543-01 • 02/11/16 • © Hunter Fan Company
1.888.830.1326
9
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
www.HunterFan.com
1.888.830.1326
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M3543-01 • 02/11/16 • © Hunter Fan Company
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
green/yellow
stripe (grounding)
green/yellow
stripe
green/yellow stripe
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
F
R
O
M
F
A
N
Place the receiver on top of the downrod
assembly as shown.
Receiver
www.HunterFan.com
1.888.830.1326
Wiring (continued)
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
M3543-01 • 02/11/16 • © Hunter Fan Company
Using the orange wire connectors
from the hardware bag:
• Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
• Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
F
R
O
M
R
E
C
E
I
V
E
R
black
blue
yellow
blue
Using the orange wire connectors
from the remote control hardware bag:
• Connect the yellow wire from
the receiver to the black wire
from the fan.
• Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
black
(ungrounded)
white (grounded)
black
white
F
R
O
M
F
A
N
white
www.HunterFan.com
1.888.830.1326
12
M3543-01 • 02/11/16 • © Hunter Fan Company
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.
www.HunterFan.com
1.888.830.1326
M3543-01 • 02/11/16 • © Hunter Fan Company
Blades
13
Insert grommets found in the hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the hardware bag.
Lightly attach the blade irons to the
motor with screws found in
the hardware bag, then securely
tighten after both screws are attached.
Remember the screws that
you kept after removing the
shipping blocks (page 6)? You
need them plus ve more from
the hardware bag for this step.
www.HunterFan.com
1.888.830.1326
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
the hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing xture falling.
Switch Housing
14
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Light Kit
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light xture falling.
Want to install your fan without a light kit?
Go to www.HunterFan.com/FAQs and click
“How do I install my fan without the light kit?”
Partially install two of the switch housing
screws found in the bag. Connect
the plugs from the upper and lower
switch housings. Make sure to line up the
colored markings on the connectors.
Align the notches in the sides of the lower
switch housing with the upper switch
housing screws. Lift the lower switch housing.
Twist the lower switch housing clockwise
to lock into place. Then thread the fan
pull chain through the hole in the light kit.
Install the third switch housing screw.
Tighten all three screws securely.
Switch
Housing
Screw
Notch
Switch
Housing
Screw
15
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
Light Kit (continued)
Connect the appropriate pull
chain pendant to each of the short
chains coming from the nial
and nial cap. The fan pull chain
controls the speed: from high to
off. The light pull chain controls
the light xture: on and off.
Press the globe and globe
keeper ush against the metal
plate. Thread the light pull chain
through the hole in the center of
the nial cap and thread the fan
pull chain through the hole in
the side of the cap. Finally, thread
only the light pull chain through
the hole in the nial and screw
the nial onto the threaded rod.
Install a light bulb in each socket.
Note: The included bulbs are not
dimmable. If you wish to utilize
the dimming feature, you may
install dimmable GU24 CFL bulbs
(sold separately).
Light
Pull
Chain
Fan
Pull
Chain
Note: Globe style and number of
lights may vary.
Finial
Finial
Cap
Globe
Keeper
Metal
Plate
Globe
M3543-01 • 02/11/16 • © Hunter Fan Company
16
www.HunterFan.com
1.888.830.1326
17
M3543-01 • 02/11/16 • © Hunter Fan Company
Remote Control
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. Install
one (1) 3-Volt, CR2032 battery (included) into the
transmitter. Clean the battery contacts and also those
of the device prior to battery installation. The battery
should be installed with the positive (+) side up.
Please contact your local battery recycling center for
proper battery disposal information.
Phillips
Head
Screw
Battery
Door
ON
Turn Power
This product contains a button battery. If swallowed,
it could cause severe injury or death in just two hours.
Seek medical attention immediately.
CAUTION:
• Always purchase the correct
size and grade of battery most
suitable for the intended use.
• Replace all batteries of a set at
the same time.
• Clean the battery contacts and
also those of the device prior to
battery installation.
• Ensure the batteries are
installed correctly with regard to
polarity (+ and -).
• Remove batteries from equipment
which is not to be used for an
extended period of time.
• Remove used batteries promptly.
The remote transmitter should already be paired
to the receiver and ready to use.
Note: If your need to pair your remote, turn fan
power off and back on at the wall switch. Within 3
minutes, press and hold both the Fan Off button
and the High button for 4 seconds to pair the
remote. To prevent faulty operation, please
ensure all other ceiling fans within range are
turned off at the wall switch while pairing.
17
www.HunterFan.com
1.888.830.1326
Remote Control (continued)
Push the 3 button on the remote transmitter
for high fan speed. Pull the fan speed chain
until the fan is on the highest speed.
3 Button
Fan Speed Chain
See next page for fan
operation instructions.
Push the light button on the remote
transmitter. Pull the light chain once. If the
light does not turn on, repeat step.
Light Button
Light Chain
Light Button
CONGRATULATIONS!
YOU’RE DONE!
18
M3543-01 • 02/11/16 • © Hunter Fan Company
18
www.HunterFan.com
1.888.830.1326
Rocker- Style
Plate
Switch Cover Plate
Removed
Tabs
To install the transmitter cradle, remove the
two screws holding the switch cover plate. Do
not remove the cover plate. Orient the cradle
by lining up the two mounting holes with
those on the cover plate. Insert and tighten
the screws. Do not over tighten.
Note: For rocker-style cover plates, break off
the tabs by pushing outward.
To turn on fan, press a fan speed button.
Speeds range from off (0) to high (3).
Quickly press the Light button to turn the
lights off and on.
Medium
Speed
Light
High
Speed
Fan
Off
Low
Speed
Operation, Maintenance, & Cleaning
To switch the direction of air ow, move the
reverse switch to the opposite position.
Reverse
Switch
19
M3543-01 • 02/11/16 • © Hunter Fan Company
www.HunterFan.com
1.888.830.1326
20
M3543-01 • 02/11/16 • © Hunter Fan Company
20
For questions regarding removing a light kit, call
customer service 1-888-830-1326.
Operation, Maintenance, & Cleaning (continued)
When cleaning the fan, use soft brushes
or cloths to prevent scratching. Cleaning
products may damage the nishes.
Changing the bulbs - unscrew the nial and
remove it from the threaded rod. Remove the
nial cap and unscrew the globe keeper while
supporting the globe with your other hand.
Carefully remove the globe. Unscrew bulbs
and replace with bulbs of same type and
wattage. Reinstall the globe assembly.
Finial
Finial Cap
Globe
Keeper
Metal
Plate
Globe
Safe-Exit
• Press the Fan Off button for at least three seconds to
initiate the Safe-Exit Mode.
• The lights will ash for visual conrmation.
• The lights will stay on 50% brightness for 15 seconds and
then begin to dim. After a total of 30 seconds, the lights
will be completely off.
The Safe-Exit Program gives you about thirty seconds
of light when you turn the lights off to exit the room
before the lights go out. To use Safe-Exit:
Note: For CFL lighting, the lights will stay on 100%
brightness for 30 seconds. After a total of 30 seconds, the
lights will be completely off.
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Hunter Fan 53214 Owner's manual
- Category
- Household fans
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hunter Fan 59049 Owner's manual
-
Hunter Fan 59313 Owner's manual
-
Hunter Fan 55045 Owner's manual
-
Hunter Fan 59653 Owner's manual
-
Hunter Fan 59589 Owner's manual
-
Hunter Fan 59206 Owner's manual
-
Hunter Fan 59237 Owner's manual
-
Hunter Fan 52 inch Maybeck Owner's manual
-
Hunter Fan 52262 Owner's manual
-
Hunter Fan 54173 Owner's manual
