LP SmartSide 39806 Installation guide

Brand: LP SmartSide

Model: 39806

Type: Installation guide

This manual is also suitable for

G

• TherearenoNationalStandardsforwoodcompositesubstratetrim.

• LPSmartSidetrimandfasciacanbeapplieddirectlyovermaterials

suchassiding,ornaileddirectlytostructuralmembersupto

24in.O.C.

•

Allfasciamustbesupportedwithsolidwoodsubfascia. Strand based

fascia may be installed without subfascia if it is 6 in. 540 series or

larger.

• TRIMMUSTNOTBEINDIRECTCONTACTWITHMASONRY,

CONCRETE,BRICK,STONE,STUCCOORMORTAR.

• Minimum6in.clearancemustbemaintainedbetweentrim

andfinishgrade.

• Trimappliedadjacenttoporches,patios,walks,etc.musthavea

clearanceofatleast1in.aboveanysurfacewherewatermightcollect.

Thesurfacemustbeslopedorotherwisedesignedtoprovideproper

drainagesothetrimisatnotimedirectlyexposedtostandingwater.

• Trimandfasciaarenotdesignedforsiding;orstructuralapplications

andshouldnotbeusedasastructuralmemberinconstructionsuch

asatrellis,railingorfencing.

• Anon-corrosivedrip-edgeordrip-capmustbeappliedatbottomedge

ofroofingwhereitmeetsthefascia.

• Trimandfasciamustnotbeappliedtogreenorcrookedstructural

framingmembers.Donotapplytrimand/orfasciaoverrainsoakedor

buckledsheathingmaterials.

• DO NOT USE STAPLES

M

• Moisturecontrolandwatervaporcontrolarecriticalelements

ofproperhousingdesign.Checkyourlocalbuildingcodesfor

applicationproceduresforhandlingmoistureandwatervapor

inyourarea.

• Followallapplicablebuildingcodespecificationsrelatingto

preventionofmoistureintrusionintothewallassembly.LP

SmartSidetrimandfasciaisawoodproduct,and,aswithallwood

products,mustbekeptfreefromconstantsourcesofmoisture.

Lackofproperventilation;exposuretorepetitivesourcesofwater

suchassprinklers,condensation,inadequateflashing;improper

sealing;orfailuretofollowcommonbuildingpracticesthatprevent

moistureintrusionintothewall-system;maycausedamage,and

willvoidthewarranty.

C

• Forthecleanestcutandlongerbladelife,afine-toothcarbide

tippedbladeisrecommended.

• Trimandfasciaaremanufacturedwithaspecialedge

coatingwhichreducesmoisture-relatedissues.Avoidripping

androutingthetrimandfascia,asitwillleavetheedges

unprotected.Ifthetrimorfasciamaterialsmustberippedyou

must,takespecialcaretoprime,paintandsealallexposed

woodfiberasdescribedinthefinishingsection.

 

TRIM AND FASCIA

190, 440, 540, 2000 SERIES

S

• Storeoffthegroundonaflatsurface,underarooforseparate

waterproofcovering.

• Keeptrimandfasciacleananddry.Inspectpriortoapplication.

G, S  J

• Sealallgapswithahigh-quality,non-hardening,paintable

sealant.Followthesealantmanufacturer’sinstructionsfor

application.

• Useahigh-qualityexteriorsealantmeetingtheASTMC920,

minimumClass25sealant.

•

Installkick-outashingtodirectthewaterintothegutter

•

Installstepashingwithminimum4in.upperleg

•

Properlyintegrateashingwiththesecondarywater-resistive

barrier.Usehousewrap,ashingtape,z-ashing,orotheritems

asneededtomaintainthecounterashingprinciple.

•

DONOTextendthesidingortrimintothekick-outashingor

gutter

•

Maintainaclearancebetweentheendofthegutterandthe

adjoiningwalltoallowforpropermaintenanceofthesiding

•

PrimeandpaintALLexposedcutedges

K-O F

LP Siding

Minimum 1" clearance

between trim and rooﬁng

Clean rain

gutter

Do not run trim or siding inside

of the kick out ﬂashing

Application instructions (cont.)

F, W, D  O

• Allopeningsmustbesealedandflashedinamannerthat

preventsmoistureintrusionorwaterbuildup.Several

examplesthataccomplishthisareshown.

•

Inahorizontalbrickfriezeorbandboardapplicationwherethe

trimoverlapsthemasonryleavea3/16-inchminimumairspace

oralayerofflashingbetweenthetrimandthemasonry.

•

Horizontaltrimorbandsshallbeflashedwithadripcapto

redirectwaterawayfromthewallassembly.

space siding 3/16 in.

from corner of wall

Minimum 2 in.

overlap

PREFERRED OUTSIDE CORNER DETAIL

Trim must extend beyond face of siding.

Minimum



/ . Gap

(if necessary, increase

spacing according to siding

requirements)

INSIDE CORNER DETAIL

Figure 1

Figure 2

ALTERNATE OUTSIDE CORNER DETAIL

Minimum



/ . Gap

(if necessary,

increase spacing

according

to siding

requirements)

Trim must extend

beyond face of siding.

Figure 3

Snug

Flush

Visible fiber

Countersunk



/–



/ .

Countersunk more

than

/8 in.

CONDITION CORRECTION

Paint

Apply sealant

Apply sealant and

re-nail

N I

•

Useaminimum8d(0.113in.diametershank),hot-dipped

galvanizednail,withaminimum0.270in.diameterhead.

•Penetratestructuralframingorwoodstructuralpanelsand

structuralframingaminimumof1in.

•

Spacenailsmaximum24in.O.C.withminimumof2nailsperstud.

• Leave

/16in.gapwheretrimbuttsintoothermaterialsandat

buttjoints,miterjointsandends.Whereedgesoftrimmeet

sidingmaterial,windows,doorsorotherfinishedopenings,

leaveaminimum

/16in.gaptoallowforpropersealing.

Provideincreasedspacingalongthetrimifspecifiedbythe

sidinginstallationinstructions.

• Leave1in.clearancebetweentrimandroofingmaterialsat

roofrake.

• Foredge-nailing,allnailholesmustbepre-drilled.Donot

attempttoedge-nailwithoutpre-drilling.

• Whenappliedasrake,cornerorbandboard,nailsmust

bespacednofurtherthan12in.apartonalternatingedges.

Nailsmustbe

/8in.fromtheedge.

• Climbcutthesurfaceofthesidingsuchthattherotationofthe

bladecutsdownwardontheprimedorprenishedsurface.

• Wheretrimbuttswindow,doorcasingsandmasonry,etc.leavea

3/16in.gapandseal.

• Attachmentoftrimasbattenstripswherethetrimisunableto

beattachedtoframingwillrequireadditionalsupportfroma

constructionadhesive.Useanexteriorgradeconstructionadhe-

sivethatmeetsthefollowingspecicationsandapplyaccording

totheadhesivemanufacture’sspecications.Attachthetrim

mechanicallywithhotdippedgalvanizedring-shanknailsno

smallerthan0.090inchshankdiameter.Thenailsmustattach

thetrimsucientlytosecurethetrimtothestructurewhilethe

constructionadhesivecompletesitscuringprocess.

 ConstructionAdhesiveSpecications:

 •Minimumbondstrength:300psi

 •Minimumapplicationtemperature:40oF

 •Paintablegrade

Insulated Sheathings

LPSmartSideSidingsmaybeinstalledoverlow-compressionrigid

foamorexteriorgypsum.Thefollowingprecautionsmustbefollowed:

• 

AdequatebracingofthewallinaccordancewiththeInterna-

tionalCodesorotherrulingbuildingcodeisrequired.

• 

Forrigidfoamsheathingupto1in.(25.4mm)thick,siding

maybenaileddirectlytothefoamsheathingunlessadrainage

planeisrequiredbythelocalbuildingcode.Naillengthmust

bein-creasedtoensureaminimum1-1/2in.(38.1mm)fastener

penetrationintothestructuralframing.

• 

Forrigidfoamsheathinggreaterthan1in.(25.4mm),aminimum

1-1/2in.(38.1mm)thickby3-1/2in.(88.9mm)widevertical

strappingorfurringstripmustbeinstalledoverthesheathing

toprovideasolid,levelnailingbaseforthesiding.Thestrap-

pingmustbesecurelyfastenedtostructuralframingspacedno

greaterthan16in.O.C.(406mm)withaminimumnailpenetra-

tionof1-1/2in.(38.1mm)andamaximumnailspacingnogreater

thanthewidthofthesiding.

Louisiana-Pacicwillassumenoresponsibilityforanydamageor

conditionarisingfromtheuseofrigidfoamorexteriorgypsum.

Application instructions (cont.)

G





.

BUTT JOINT DETAIL

4 in. Vertical Flashing

Trim

Nail Fin (do not damage)

DOORS & WINDOWS

Glass

Minimum



/ . Gap

(if necessary, increase spacing

according to siding requirements)



/ . Space

Figure 4

Figure 5

Siding

HORIZONTAL

TRIM AND

BAND BOARD

Trim

Flashing

Brick

Flashing



/ . Space



/ . Space

Weather

Resistant

Barrier

Shim

Figure 6

J D

• Endsmustbespacedandjointsmaylightlytouchinrunsless

than16feet.Buttjointsrequirea3/16in.gapinruns16feetor

 greater.Sealwithahighqualitynon-hardeningpaintablelong-

 lifesealant.

•Buttjointsrequirefour(4)nailswithtwonailsoneithersideof

thejointateachedge.

TRIMBOARD 3/16 IN. JOINT DETAIL

Figure 8

Space

and seal with

sealant

Figure 9

• End-to-endjointsinverticaltrimshouldbeinstalledso

thattheyshedwater.

• Do not miter corner joints of band boards, fascia, etc.

• Allowtheendofthetrimtolapovertheendofthe

adjoiningtrim,gap3/16in.andcaulkwithsealant.

Figure 7

VINYL SIDING

Allowdrainagebetween

horizontaltrimandJ-channel

whenadjoiningvinylsiding

Window

Framing

Trim

Water release

Z flashing

Vinyl

Siding

• Donotusescarfjoints.

TheLouisiana-PacificCorporation(“LP”)LPSmartSidetrimandfascia

(the“Products”)limitedwarranty(the“Warranty”)appliesonlyto

structuresonwhichtheProductshavebeenapplied,finishedand

maintainedinaccordancewiththepublishedapplication,finishing

andmaintenanceinstructionsineffectatthetimeofapplication.

Thefailuretofollowsuchapplication,finishingormaintenance

instructionswillvoidtheWarrantyastotheportionoftheProducts

affectedbythevariance(the“AffectedProducts”).

LPassumesnoliabilityforanylossordamagesustainedbythe

AffectedProductsandisexpresslyreleasedbythepurchaseror

ownerfromanysuchlossorliability.

AnymodificationoftheWarranty’sapplication,finishingor

maintenancerequirementsisvoidandunenforceableunless

approvedinwritingpriortoapplicationbytheSidingGeneralManager

orhisdesigneeandamemberoftheLPLegalDepartment.

Foracopyofthewarrantyorforinstallationandtechnicalsupport,visitthe

LPSmartSideproductsupportWebsiteat:

orforadditionalsupportcall800-450-6106.

www.lpsmartside.com

WARRANTYREMEDIESARENOTAVAILABLEIF

REQUIREMENTSARENOTFOLLOWED.

NEVER NAIL INTO

EDGES WITHOUT

PRE DRILLING

DO NOT MITER

EDGES

SEAL AND PAINT

M

• Donotmitertrimedges.45degreemiteringoftrimends

arounddoorandwindowopeningsisacceptable,aswellas

joining.

DO NOT MITER

CUT THE

CORNER JOINT

G E

• Atgableends,abackerboard(suchasabargerafter)shouldbe

usedunderfasciatoprovidemaximumsupportalongthelength

oftheproduct(seeFigures10and11.)

• Iftrimandfasciaisinstalleddirectlytolookoutsonan

overhangingrake,thelookoutsmustbeinstallededgewiseand

mustbespacednowiderthan24in.O.C.(seeFigures10and

11).THISAPPLICATIONAPPLIESTOMINIMUM6in.540SERIES

STRANDTRIMONLY.

FASCIA DETAIL

FASCIA

SOFFIT

TRIM

Installdrip-edgeor

drip-captoprevent

waterbuildupbehind

fasciaandtrim.

Ridge

First

common rafter

End or verge

rafter

Barge rafter

2x or 4x lookouts

Fascia

Ridge

First

common rafter

End or verge

rafter

Barge rafter

2x or 4x lookouts

Fascia

F  R B  C

• Alljointsmustbesupportedby

framing.

• Donotnailfromthefaceofone

trimmemberintotheedgeof

another.

• Donotmitercutthecornerjoint.

F

• Primeandpaintallexposedsurfacesincludingalldrip

edges or where water will hang.

• Applyfinishcoatassoonaspossibleorwithin180days

ofapplication.

• High-qualityacryliclatexpaint,speciallyformulatedforuseon

woodandengineeredwoodsubstrates,ishighlyrecommended.

Semi-glossorsatinfinishoiloralkydpaintsareacceptable.For

flatalkydpaint,pleasecheckwiththecoatingmanufacturerfor

theirrecommendationsforuseoncompositewoodsiding.

• Followthecoatingmanufacturer’sapplicationand

maintenanceinstructions.

DO NOT USE

• Semi-transparentandtransparentstains.

• Shakeandshinglepaints.

• Vinyl-basedresinformulassuchasvinylacetate,PVA,

vinylacetate/acryliccopolymerpaints.

HANDLE PREFINISHED LP SMARTSIDE PRODUCTS WITH

EXTREME CARE DURING STORAGE AND APPLICATION. TOUCH

UP ANY DAMAGE TO THE FINISH THAT MAY OCCUR DURING

APPLICATION PER PREFINISHERS SPECIFICATIONS.

TrimBoard

2" x 6"

Blocking

Rafter

Cal. Prop 65 Warning: Use of this product may result in exposure to

wood dust, known to the State of California to cause cancer.

Application instructions (cont.)

areregisteredtrademarksofLouisiana-PacificCorporation.PrintedinU.S.A.

NOTE:Louisiana-PacificCorporationperiodicallyupdatesandrevisesitsproductinformation.

Toverifythatthisversioniscurrent,call800-450-6106.

       LPZB05211/14

Figure 10

Figure 11

Figure 12

Figure 13

Figure 14

LP SmartSide 39806 Installation guide

Brand: LP SmartSide

Model: 39806

Type: Installation guide

This manual is also suitable for

Download PDF

report

LP SmartSide 39806 Installation guide

This manual is also suitable for

LP SmartSide 39806 Installation guide

Related papers

Other documents