Sundance Spas Maxxus Owner's manual

880 SERIES OWNER’S MANUAL

Maxxus

™

| Aspen

®

| Optima

®

| Cameo

®

| Altamar

®

| Marin

®

| Capri

®

P.N.:6530-395C Rev. B

Attention New Hot Tub Owner!

Congratulations on the purchase of your new Sundance

®

hot tub! The

following is a list of automated functions performed by your hot tub. These

functions are listed below in an attempt to suppress any operational

concerns you may have during the rst 24 hours of ownership! Also listed

below are important maintenance recommendations you should observe

on a regular basis to protect your new investment.

Maintain Healthy Spa Water

Always maintain your hot tub’s water chemistry within the following

parameters:

With CLEARRAY® Without CLEARRAY®

pH 7.4-7.6 7.4-7.6

Free chlorine no less than 1.0 ppm 3.0-4.0 ppm

Free Bromine no less than 2.0 ppm 2.0-4.0 ppm

Total Alkalinity 100-150 ppm 100-150 ppm

Calcium Hardness 150-250 ppm 150-250 ppm

IMPORTANT: CLEARRAY® Water Purication System is factory

installed. If the CLEARRAY® system is altered or is not operating

efciently follow the “without CLEARRAY®” water chemistry param-

eters. Such parameters are dened by the Association of Pool and Spa

Professionals. CLEARRAY® requires an annual lamp replacement to

properly sanitize your water.

!

TO DECREASE RISK OF INFECTION OR DISEASE!

Always

maintain your spa lter as outlined below to ensure healthy spa water.

Refer to pages 66-68 for additional information.

Required Filter Maintenance

Your new hot tub is equipped with an advanced

MicroClean®

Ultra water

ltration system that provides unsurpassed water quality! To ensure

maximum water quality at all times, you should replace the lter cartridge

every six months, or earlier as necessary. The lter cartridge is designed

to be thrown away! Attempts to reuse the lter cartridge may result in

the re-release of unwanted particles back into the hot tub. See pages

66-68 for detailed lter cartridge replacement instructions.

Required Water Replacement

!

TO DECREASE RISK OF INFECTION OR DISEASE!

You

should replace the hot tub’s water every 3 to 6 months. The frequency

depends on a number of variables including frequency of use, number of

users, and attention paid to water quality maintenance. You will know it is

time for a change when you cannot control sudsing and/or you can no

longer get

the normal feel or sparkle to the water, even though the key

water balance measurements are all within the proper parameters. See

pages 73-75 for additional information.

880 SERIES

Table of Contents

1.0 Important Hot Tub Owner Information ............................1

2.0 FCC Notice ........................................................................1

3.0 Important Safety Instructions for all Spa Owners .........2

3.1 Entrapment Risk .......................................................................... 6

3.2 Hyperthermia ............................................................................... 7

3.3 Important Additional CSA Safety Instructions (Canada Only) ...... 8

4.0 Locating Your Sundance Hot Tub ...................................8

4.1 Outdoor Location ......................................................................... 9

4.2 Indoor Location .......................................................................... 10

4.3 Location for the Optional SunSmart™ 2.0 System .................... 11

5.0 General Electrical Safety Instructions ..........................12

6.0 Electrical Installation Instructions (240V Service) .......13

7.0 Power Requirements ......................................................16

7.1 North American 60 Hz Power Options ....................................... 16

8.0 Hot Tub Fill Up Procedure ..............................................17

9.0 Hot Tub Features ............................................................22

9.1 Maxxus™ Hot Tub Features ...................................................... 22

9.2 Maxxus Massage/Waterfall Selector Diagram ........................... 23

9.3 Maxxus Air Controls Diagram .................................................... 24

9.4 Aspen® Hot Tub Features ......................................................... 25

9.5 Aspen Massage/Waterfall Selector Diagram ............................. 26

9.6 Aspen Air Controls Diagram....................................................... 27

9.7 Optima® Hot Tub Features ........................................................ 28

9.8 Optima Massage/Waterfall Selector Diagram ............................ 29

9.9 Optima Air Controls Diagram ..................................................... 30

9.10 Cameo® Hot Tub Features ........................................................ 31

9.11 Cameo Massage/Waterfall Selector Diagram ............................ 32

9.12 Cameo Air Controls Diagram ..................................................... 33

9.13 Altamar® Hot Tub Features ....................................................... 34

9.14 Altamar Massage/Waterfall Selector Diagram ........................... 35

9.15 Altamar Air Controls Diagram .................................................... 36

9.16 Marin® Hot Tub Features .......................................................... 37

9.17 Marin Massage/Waterfall Selector Diagram .............................. 38

9.18 Marin Air Controls Diagram ........................................................ 39

9.19 Capri® Hot Tub Features ........................................................... 40

9.20 Capri Massage/Waterfall Selector Diagram ............................... 41

9.21 Capri Air Controls Diagram ........................................................ 42

880 SERIES

10.0 SunTouch™ Control Panel Main Menu .........................43

10.1 SunTouch™ Welcome Screen ................................................... 43

10.2 Register Your New Spa .............................................................. 43

10.3 Home Menu ............................................................................... 45

11.0 Operating Instructions ...................................................46

11.1 Activating the Jets Pumps and Blower....................................... 46

11.2 Lights Menu ............................................................................... 47

11.3 Music Menu................................................................................ 49

11.4 Connecting the BLUEWAVE® System with

your Bluetooth® device .............................................................. 50

11.5 Audio Settings Menu .................................................................. 51

11.6 CLEARRAY on Demand ............................................................ 52

11.7 Selecting The Desired Massage Action ..................................... 52

11.8 Adjusting Fluidix Reex, Nex, ST, Intelli-Jets

And Focus-Relief ....................................................................... 52

11.9 Air Controls ................................................................................ 53

11.10 Waterfall Control ........................................................................ 53

11.11 Fragrance Dispenser ................................................................. 53

11.12 Indicator Light ............................................................................ 53

12.0 Programming and Operation Instructions ...................54

12.1 Programming the Heating Mode ................................................ 55

12.2 Programming the Primary Filter ................................................. 56

12.3 Programming the Secondary Filter ............................................ 57

12.4 Cleanup Cycle............................................................................ 58

12.5 Blow-Out Cycle .......................................................................... 58

12.6 Water Care Programming .......................................................... 58

12.7 Optional Wi-Fi Setup .................................................................. 61

12.8 Locking the Spa ......................................................................... 62

12.9 Programming the Time and Date ............................................... 63

12.10 Programming the Language ...................................................... 64

12.11 Units Display .............................................................................. 64

12.12 System Information .................................................................... 65

13.0 Hot Tub Maintenance ......................................................66

13.1 Cleaning/Replacing the Filter Cartridge ..................................... 66

13.2 Quick Release Door (Except Maxxus and Aspen Models) ........ 68

13.3 Draining And Relling................................................................. 69

13.4 Cleaning The Hot Tub Interior .................................................... 70

13.5 Pillow Care ................................................................................. 70

13.6 Maintaining the Hot Tub Cabinet................................................ 71

13.7 Vinyl Cover Care And Maintenance ........................................... 71

13.8 Winterizing ................................................................................. 72

13.9 Restarting Your Hot Tub in Cold Weather .................................. 73

880 SERIES

14.0 Water Quality Maintenance ............................................73

14.1 pH Control .................................................................................. 74

14.2 Sanitizing ................................................................................... 74

14.3 CLEARRAY® Water Purication System ................................... 75

14.4 CLEARRAY® Bulb Replacement and Quartz

Tube Maintenance ..................................................................... 75

14.5 Other Additives........................................................................... 77

14.6 Handrail Maintenance ................................................................ 78

15.0 Troubleshooting - Display Messages ...........................79

16.0 Troubleshooting - Procedures .......................................82

17.0 Typical Hot Tub Wiring Diagrams A-B

(North American 60 Hz Models Only) ............................84

18.0 North American 60 Hz Electrical Wiring Diagram ........85

18.1 North American 60 Hz Maxxus/Aspen Electrical

Wiring Diagram .......................................................................... 85

18.2 North American 60 Hz Altamar/Cameo/Capri/Marin/

Optima Electrical Wiring Diagram .............................................. 86

18.3 Dip Switch Settings .................................................................... 87

.

Page 1

880 SERIES

1.0 Important Hot Tub Owner Information

Your Sundance

®

hot tub is constructed to the highest standards and

is capable of providing many years of trouble-free use. However,

because heat retentive materials are utilized to insulate the hot tub for

efcient operation, an uncovered hot tub surface and wall ttings directly

exposed to sunlight and high temperatures for an extended period are

subject to permanent damage or discoloration. Damage caused by

exposing the hot tub to this abuse is not covered under warranty. We

recommend that you always keep the hot tub full of water when it is

exposed to direct sunlight and that you keep the Sundance insulating

cover in place at all times when the hot tub is not in use. Read and

carefully follow the requirements for your hot tub’s support base found in

the Section 4.0 titled, “Locating Your Sundance Hot Tub” (page 8) or

as prescribed by your authorized Sundance Spas dealer.

Sundance hot tubs constantly strives to offer the nest hot tubs

available, therefore, modications and enhancements may be made

which affect the specications, illustrations and/or instructions contained

herein.

2.0 FCC Notice

This equipment has been tested and found to comply with the limits for

a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

1. Rearrange or relocate the receiving antenna;

2. Increase the separation between the equipment and receiver;

3. Connect the equipment into an outlet on a circuit different from the

circuit connected;

4. Consult the dealer or an experienced radio/TV technician for help.

(Changes or modications not expressly approved by the party

responsible for FCC compliance could void the user’s authority to

operate this equipment).

Page 2

880 SERIES

3.0 Important Safety Instructions for all Spa Owners

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY!

This spa was manufactured to meet the standards and specications

outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB

Safety Act). When installing and using this spa, basic safety precautions

should always be followed, including:

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Extreme caution must be exercised to prevent unauthorized access

by children.

• To avoid accidents, ensure that children do not use this spa unless

supervised at all times. Adult supervision is a critical safety factor in

preventing children from drowning.

• Use the straps and clip tie downs to secure the spa cover when not

in use. This will help discourage unsupervised children from entering

the spa. Keep the spa cover secure in high-wind conditions.

• There is no representation that the cover, clip tie-downs, or actual

locks will prevent access to the spa.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

• Keep hair, loose articles of clothing or hanging jewelry away from

suction ttings, rotating jets or other moving components to avoid

entrapment that could lead to drowning or severe injury.

• Never use the spa unless all suction guards, lter, lter lid, or skimmer

assembly are installed to prevent body and/or hair entrapment.

• Never operate or use the spa if the lter, lter lid, or skimmer

assembly are broken or any part of the skimmer assembly is missing.

Please contact your dealer or nearest service center for service.

• The suction ttings and suction covers in this spa are sized to match the

specic water ow created by the pump(s). If it is necessary to replace

the suction ttings, suction covers or pump(s), be sure that the ow

rates are compatible and are in compliance with the VGB Safety Act.

• Never replace a suction tting or suction cover with one rated less

than the ow rate marked on the original suction tting. Using

improper suction ttings or suction covers can create a body or hair

suction entrapment hazard that may lead to drowning or severe injury.

3.

!

DANGER: RISK OF SEVERE INJURY FROM ELECTRIC

SHOCK OR DEATH FROM ELECTROCUTION!

• Install the spa at least 5 feet (1.5m), from all metal surfaces. As an

alternative, a spa may be installed within 5 feet of metal surfaces

if each metal surface is permanently connected (bonded) by a

minimum No. 8 AWG (8.4 mm²) solid copper conductor attached

to the wire connector on the grounding lug, inside the equipment

compartment on the equipment box.

Page 3

880 SERIES

• A grounding wire connector is provided on this unit to connect a

minimum No. 8 AWG (8.4 mm²) solid copper conductor between

this unit and any metal equipment, metal enclosures of electrical

equipment, metal water pipe, or conduit within 5 feet (1.5m) of the

unit.

• Never permit any electrical appliance, such as a light, telephone,

radio, television, etc. within 5 feet (1.5m) of a spa unless such

appliances are built-in by the manufacturer.

• Never bring any electrical appliances into or near the spa.

• Never operate any electrical appliances from inside the spa or when

you are wet.

• The electrical supply for this product must include a suitably rated

switch or circuit breaker to open all ungrounded supply conductors

to comply with section 422-20 of the National Electrical Code/

USA, ANSI/NFPA 70. The disconnecting means must be readily

accessible and visible to the spa occupant but installed at least 5

feet (1.5m), from the spa.

• The electrical circuit supplied for the hot tub must include a suitable

ground fault circuit interrupter (GFCI) as required by NEC Article

680-42.

4.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Extreme caution must be exercised to prevent diving or jumping

into the spa or slipping and falling, which could result in

unconsciousness, drowning, or serious injury. Remember that wet

surfaces can be very slippery.

• Never stand, walk or sit on the top railing of the spa.

5.

!

WARNING: RISK OF HYPERTHERMIA (OVER-HEATING)

CAUSING SEVERE INJURY, BURNS, WELTS OR DEATH!

• Water temperature in excess of 104°F (40°C) may be injurious to

your health.

• Refer to Section 3.2 Hyperthermia for specic causes and symptoms

of this condition.

• The water in the spa should never exceed 104°F (40°C). Water

temperatures between 100°F (38°C) and 104°F (40°C) are

considered safe for a healthy adult.

• Lower water temperatures are recommended for young children

(children are especially sensitive to hot water) and when spa use

may exceed 10 minutes.

• The Consumer Products Safety Commission/USA has stated that

the water temperature in a spa should not exceed 104°F (40°C).

• Always test the spa water temperature before entering the spa.

The user should measure the water temperature with an accurate

thermometer since the tolerance of water temperature-regulating

devices may vary as much as +/- 5°F (2°C).

Page 4

880 SERIES

6.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Since excessive water temperatures have a high potential for

causing fetal damage during the early months of pregnancy, if

pregnant or possibly pregnant, consult your physician before using a

spa.

• Pregnant or possibly pregnant women should limit spa water

temperatures to 100°F (38°C).

• Persons suffering from obesity or a medical history of heart disease,

low or high blood pressure, circulatory system problems, diabetes,

infectious diseases or immune deciency syndromes should consult

a physician before using a spa.

• If you experience breathing difculties in association with using or

operating your spa, discontinue use and consult your physician.

• Persons using medication should consult a physician before using

a spa since some medication may induce drowsiness, while other

medication may affect heart rate, blood pressure, and circulation.

• Persons suffering from any condition requiring medical treatment, the

elderly, or infants should consult with a physician before using a spa.

• The use of alcohol, drugs, or medication before or during spa use

may lead to unconsciousness with the possibility of drowning.

7.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

• Prolonged immersion in a spa may be injurious to your health.

• Observe a reasonable time limit when using the spa. Exposures

at higher temperatures can cause high body temperature (over-

heating). Symptoms may include dizziness, nausea, fainting,

drowsiness, and reduced awareness. These effects could possibly

result in drowning or serious injury.

• Never use a spa immediately following strenuous exercise. Enter

and exit the spa slowly. Wet surfaces can be slippery.

8.

!

WARNING: TO DECREASE RISK OF INFECTION OR

DISEASE!

• To reduce the risk of contracting a waterborne

illness (e.g. an infec-

tion, bacteria or virus) and/or respiratory ailments

, maintain water

chemistry within the parameters listed on the inside cover of this

manual and consult with a licensed engineer regarding proper venti-

lation if installed indoors or in an enclosed area.

• People with infectious diseases should not use a spa to avoid water

contamination, which could result in spreading infections to others.

• Always shower before and after using your spa. Maintain water

chemistry in accordance with manufacturer’s instructions. Failure to

do so may result in contracting a waterborne

illness (e.g. an infec-

tion, bacteria or virus).

Page 5

880 SERIES

9.

!

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the risk of

contracting a waterborne

illness (e.g. an infection, bacteria or virus)

and/or respiratory ailments

that could be present in the air or water.

Consult a licensed architect or building contractor to determine your

specic needs if installing your hot tub indoors.

10. CAUTION: TO DECREASE RISK OF PRODUCT DAMAGE.

• Maintain water chemistry in accordance with manufacturer’s

instructions.

• Proper chemical maintenance of spa water is necessary to maintain

safe water and prevent possible damage to spa components.

11.

!

WARNING: RISK OF SEVERE INJURY OR DEATH!

The appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience or knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

12. NOTE: This spa is not intended nor designed to be used in a

commercial or public application. The spa buyer shall determine

whether there are any code restrictions on the use or installation

of this spa since local code requirements vary from one locality to

another.

Hot Tub Safety Literature

To ensure you have a safe and enjoyable hot tub experience,

learn all you can about hot tub safety and emergency procedures.

Especially useful are the brochures listed below:

• Children Aren’t Waterproof

• Pool and Spa Emergency Procedures For Infants and Children

• Layers of Protection

• The Sensible Way to Enjoy Your Spa or Hot Tub

The Association of Pool and Spa Professionals publishes these

brochures. To acquire a brochure:

• Ask your hot tub dealer (they may have copies)

• Go to http://www.apsp.org

• Conduct your own search on the internet

• Write to the following address:

The Association of Pool and Spa Professionals

2111 Eisenhower Avenue

Alexandria VA 22314

703.838.0083

Page 6

880 SERIES

3.1 Entrapment Risk

The Consumer Products Safety Commission/USA has reported that

users of pools and spas have become entrapped (stuck) to drain and/or

suction ttings causing death, drowning, or serious injury (see diagram

below). This spa was manufactured to meet the standards and specica-

tions outlined in the “Virginia Graeme Baker Pool and Spa Safety Act”

(VGB Safety Act). Entrapment risk can be minimized if proper precau-

tions are taken.

DANGER: RISK OF PERSONAL INJURY OR DEATH!

Never operate the spa if a suction tting, suction cover, lter,

lter lid or skimmer assembly are broken, damaged or miss-

ing.

!

NOTE: SUCTION COVERS MUST BE REPLACED EVERY 5 YEARS.

1.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Hair entrapment: May occur if hair is entangled, knotted or snagged

in a drain suction or skimmer assembly. This has been reported in

persons who when submerge themselves underwater, allowing hair

to come close and/or within the reach of the suction ttings, suction

covers or skimmer assembly.

• Keep hair away from suction ttings, suction covers, lter, lter lid or

skimmer assembly.

• Children are at risk for hair entrapment if swimming under water.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

2.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Limb entrapment: May occur when a limb becomes entrapped,

inserted or sucked into a suction or outlet opening.

• Always keep suction ttings, suction covers, lter, lter lid

or skimmer assembly in place when operating to avoid limb

entrapment.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

Suction Fittings,

Suction Covers

(locations vary

by models)

Filter, Filter

Lid, Skimmer

Assembly

(location and

style vary by

models)

Page 7

880 SERIES

3.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Body entrapment: May occur when part of the torso becomes

entrapped, inserted or sucked into a suction or outlet opening.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

4.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Evisceration (disembowelment) entrapment: May occur when the

buttocks becomes entrapped, inserted or sucked into a suction or

outlet opening.

• Never sit on suction ttings, suction covers, lter, lter lid or skimmer

assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

5.

!

DANGER: RISK OF SEVERE INJURY OR DROWNING!

Mechanical entrapment: May occur when jewelry, swimsuit, or

hair accessories become entangled, knotted or snagged in a drain

suction or skimmer assembly.

• Never allow your jewelry, swimsuit, or hair accessories to come close

to the suction ttings, suction covers or skimmer assembly.

• Never allow children to play or get near the suction ttings, suction

covers, lter, lter lid or skimmer assembly.

3.2 Hyperthermia

Prolonged immersion in hot water may induce hyperthermia (over-

heating). The use of alcohol or drugs can greatly increase the risk of fatal

hyperthermia in spas. A description of the causes, symptoms, and effects

of hyperthermia are as follows:

Hyperthermia occurs when the internal temperature of the body reaches

a level several degrees above the normal body temperature of 98.6°F

(37°C). The symptoms of hyperthermia include drowsiness, lethargy

(fatigue), and an increase in the internal temperature of the body (feeling

of being too hot). The effects of hyperthermia include:

• Unawareness of impending hazard;

• Failure to perceive heat;

• Failure to recognize the need to exit spa;

• Physical inability to exit spa;

• Fetal damage in pregnant women; and

• Unconsciousness and danger of drowning.

A Warning Sign is provided in your warranty packet. Please install at

a location near your spa, where it is visible to users of the spa. For

additional or replacement Warning Signs please contact your local

Sundance spas dealer and reference item number #6530-082.

Page 8

880 SERIES

3.3 Important Additional CSA Safety Instructions (Canada Only)

When using this electrical equipment, basic safety precautions should

always be followed, including the following:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. A green colored terminal or a terminal marked G, Gr, Ground,

Grounding or the symbol* is located inside the supply termi-

nal box or compartment. To reduce the risk of electric shock, this

terminal must be connected to the grounding means provided in the

electric supply service panel with a continuous copper wire equiva-

lent in size to the circuit conductors that supply this equipment (*IEC

Publication 417, Symbol 5019).

3. At least two lugs marked “Bonding Lugs” are provided on the exter-

nal surface or on the inside of the supply terminal box/compartment.

To reduce the risk of electric shock, connect the local common bond-

ing grid in the area of the spa to these terminals with an insulated or

bare copper conductor not smaller than No. 6 AWG (10 mm²).

4. All eld installed metal components such as rails, ladders, drains or

other similar hardware within 10 feet (3m) of the spa shall be bonded

to the equipment grounding buss with copper conductors not smaller

than No. 6 AWG (10 mm²).

5. SAVE THESE INSTRUCTIONS.

4.0 Locating Your Sundance Hot Tub

WARNING: For spas that are to rest on balconies,

roofs or other platforms not specically tied into main

structural support, consult a professional Structural En-

gineer with experience in this type of application.

!

IMPORTANT: Because of the combined weight of the spa, water

and users, it is extremely important that the base upon which the

spa rests be smooth, at, level and capable of uniformly support-

ing this weight, without shifting or settling, for the entire time the

spa is in place. If the spa is placed on a surface which does not

meet these requirements, damage to the skirt and/or the spa shell

may result. Damage caused by improper support is not covered

under warranty. It is the responsibility of the spa owner to assure

the integrity of the support over time. We recommend a poured,

reinforced concrete slab with a minimum thickness of 4 inches (10

cm). Wood decking is also acceptable provided it is constructed so

that it meets the requirements outlined above.

Page 9

880 SERIES

The spa must be installed in such a manner as to provide drainage away

from it. Placing the spa in a depression without provisions for proper

drainage could allow rain, overow and other casual water to ood the

equipment and create a wet condition in which it would sit in. For spas

which will be recessed into a oor or deck, install so as to permit access

to the equipment, either from above or below, for servicing. Make certain

that there are no obstructions which would prevent removal of all side

cabinet panels and access to components, especially on the side with

the equipment bay doors.

CAUTION: If the spa is indoors or located in an enclosed area,

proper ventilation should be discussed with an Engineer or authority

competent enough to understand the necessary provisions needed

to vent moist or heated air and air associated with chemical odors

outdoors. When the spa is in use considerable amounts of

moisture will escape potentially causing mold and mildew. This

can cause health risk. Over time, this can damage certain surfaces,

surroundings, and equipment.

4.1 Outdoor Location

In selecting the ideal outdoor location for your hot tub, we suggest that

you take into consideration the following:

• The proximity to changing area and shelter (especially in regions

subject to cold weather).

• The pathway to and from your hot tub (this should be free of debris

so that dirt and leaves are not easily tracked into the hot tub).

• The closeness to trees and shrubbery (remember that leaves and

birds could create extra work in keeping the hot tub clean).

• A sheltered environment (less wind and weather exposure can result

in lowered operation and maintenance costs).

• The overall enhancement of your environment. It is preferable not

to place the hot tub under an unguttered roof overhang since run-off

water will shorten the life expectancy of the hot tub cover.

• For spas that are to rest on balconies, roofs or other platforms not

specically tied into main structural support, consult a professional

Structural Engineer with experience in this type of application.

• In the unlikely event that you should ever need to access or gain

entry to any portion of the spa for servicing, it is highly recommended

that you plan your outdoor installation to provide full access to the

entire spa. Please take this into consideration when placing the spa

in a deck or enclosed by a surrounding.

• Consider locating your spa away from any reective surface or glass

to prevent any damage to the synthetic skirt.

• Do not shim the spa. To ensure proper support the spa must sit at

on the intended foundation.

!

Page 10

880 SERIES

4.2 Indoor Location

For indoor installations many factors need to be considered before

installing a spa indoors:

WARNING: In addition to maintenance of lters and water

chemistry, proper ventilation is recommended to reduce the

risk of contracting a waterborne

illness (e.g. an infection, bac-

teria or virus) and/or respiratory ailments

that could be pres-

ent in the air or water. Consult a licensed architect or building

contractor to determine your specic needs if installing your

hot tub indoors.

!

• PROPER FOUNDATION: Consult a Structural Engineer when

considering a foundation that will adequately support the spa

the entire time it is in place. Proper support is critical especially

if the spa is to rest on a second story or higher. For spas that are

to rest on balconies, roofs or other platforms not specically tied

into the main structural support, you should consult a professional

Structural Engineer with experience in this type of application.

• PROPER DRAINAGE: It is extremely important to have in place

measures to sufciently handle excessive water spillage. Be

sure the ooring in which the spa rests on has adequate drainage

and can handle draining of the entire contents of the spa. Be sure

to make provisions for ceilings or any other structures that may be

below the spas installation. Areas around your spa can become wet

or moist so all ooring and subsequent furniture, walls and adjacent

structures should be able to withstand or resist water and moisture.

• PROPER VENTILATION: Proper ventilation should be discussed

with an Engineer or authority competent enough to understand

the necessary provisions needed to vent moist or heated air

and air associated with chemical odors outdoors. When the spa

is in use considerable amounts of moisture will escape potentially

causing mold and mildew, over time this can damage certain

surfaces and or surroundings.

• SUFFICIENT ACCESS: In the unlikely event that you should ever

need to access or gain entry to any portion of the spa for servicing,

it is highly recommended that you plan your indoor installation to

provide full access to the entire spa.

• WARRANTY: Damage caused by not following these guidelines

or any improper installation not in accordance with local codes or

authorities is not covered under the spas warranty. Please consult

your local state or city building ordinances.

• DO NOT SHIM THE SPA. To ensure proper support the spa must sit

at on the intended foundation.

Page 11

880 SERIES

4.3 Location for the Optional SunSmart™ 2.0 System

IMPORTANT! Choose an installation site with the front control panel

side pointing towards your home’s Wi-Fi router.

CAUTION: You must make sure that the spa control panel side

has a clear unobstructed line-of-site of the home Wi-Fi router. This

action ensures maximum signal strength between the spa and your

home’s Wi-Fi router.

Verify your home router’s Wi-Fi strength at the proposed spa location.

Front control panel side of spa must point towards your home’s Wi-Fi

router in your home as illustrated, Figure 4.3a. Stand near the proposed

front control panel side of the spa with your cell phone, then login to the

internet using your home Wi-Fi router signal (not 3G or 4G) and verify

results as follows:

If the home Wi-Fi router signal is strong (3-4 bars) and Internet access is

stable, the proposed installation site is a good choice.

If the home router’s Wi-Fi signal is weak and Internet access is slow or

produces an error, the proposed installation site is not a good choice.

• It may be necessary to choose another spa installation site.

• Relocate your home Wi-Fi router closer to the spa.

• Install a “repeater” device in the room closest to the spa to boost the

home’s router Wi-Fi signal at the proposed spa installation site.

Home WiFi

Router

102

°

Figure 4.3a

Page 12

880 SERIES

5.0 General Electrical Safety Instructions

Your new Sundance

®

hot tub is equipped with the “state-of-

the-art” equipment system. It contains the most advanced

safety and self-protective equipment in the industry.

Nonetheless, this hot tub must be installed properly to

ensure dependable usage. Please contact your local

Sundance Spas dealer or local building department should you have any

questions regarding your installation.

Proper grounding is extremely important. Sundance hot tubs are

equipped with a current collector system. A pressure wire connector is

provided on the surface of the control box, located inside the equipment

door (Figure C, page 15) to permit connection of a bonding wire

between this point and any ground metal equipment, metal water pipe or

conduit within 5 feet (1.5m) of the hot tub, or copper clad grounding rod

buried within 5 feet (1.5m) of the hot tub. Bonding wire must be at least

No. 8 AWG (8.4 mm²) solid copper wire. This is a most important safety

assurance feature.

Before installing your hot tub, check with your local government/electri-

cal authority to ensure installation conforms to local country/area state

codes.

Page 13

880 SERIES

6.0 Electrical Installation Instructions (240V Service)

IMPORTANT NOTICE: The electrical wiring of this hot

tub must meet the requirements of the National Electrical

Code (NEC) and any applicable state, local or country codes.

The electrical circuit must be installed by a qualied

electrician and approved by a local building/electrical

inspection authority in your state or country.

1.

!

DANGER: TO DECREASE THE RISK OF SHOCK,

PRODUCT DAMAGE OR ELECTRICAL FIRE.

This hot tub must be permanently connected (hard-wired) to the

power supply. No plug-in connections or extension cords are

to be used in conjunction with the operation of this hot tub.

Supplying power to the hot tub which is not in accordance with these

instructions will void both the independent testing agency listing and

the manufacturer’s warranty.

2. The power supplied to this hot tub must be a dedicated circuit with no

other appliances or lights sharing the power provided by the circuit.

3. To determine the current, voltage and wire size required, refer to

Section 7.0 (page 16) for your specic hot tub model.

• Wire size must be appropriate per NEC and/or local/country codes.

• We recommend type THHN wire.

• All wiring must be copper to ensure proper connections. Do not use

aluminum wire.

• When using wire larger than #6 (10 mm²), add a junction box near

the hot tub and reduce to short lengths of #6 (10 mm²) wire to

connect to the hot tub.

4. The electrical supply for this product must include a suitably rated

switch or circuit breaker to open all ungrounded supply conductors

to comply with Section 422-20 of the National Electrical Code, ANSI/

NFPA 70. The disconnecting means must be readily accessible and

visible to the hot tub’s occupant but installed at least 5 feet (1.5m)

from the hot tub.

5. The electrical circuit supplied for the hot tub must include a suitable

ground fault circuit interrupter (GFCI) as required by NEC Article

680-42.

6. To gain access to the hot tub’s power terminal block, remove the

screws securing the center cabinet panel (Maxxus™ and Aspen®

models only) or the Quick Release buttons (except Maxxus and Aspen

models) on the side of the hot tub under the controls. Then remove the

control box door screws and door (Figure C, page 15).

Page 14

880 SERIES

7. For Australia/New Zealand, the spa should be supplied through

a residual current device (RCD) with a rated tripping current not

exceeding 30mA (IEC 60335-2-60).

8. Select the power supply entrance you want to use (Figures A-B,

pages 14-15) and remove the short cabinet panel from the front

of the hot tub, then feed cable through the large opening provided on

the bottom of the control box.

9. Connect wires, color to color, on terminal blocks TB1 and TB3

(Figure D). TIGHTEN SECURELY! All wires must be hooked up

securely or damage could result.

10. Install control box door and reinstall the cabinet panel(s).

Figure A (Maxxus/Aspen Equipment Area)

102

°

8

9

10

6

2 2

13

12

7

4

11

16

3

14

5

1

15

Note: Equipment location (such as pumps, CLEARRAY® system, drain,

heater etc.) varies by model.

1. Control Box

2. Power Supply Entrance(s)

3. Jets Pump

4. Jets Pump

5. Jets Pump

6. Blower

7. Heater

8. Hot Tub Drain (Removable

External Drain Cap)

9. Pump Drain Plug(s)

10. Filter/Circulation Pump

11. CLEARRAY® (Ultraviolet) Water

Purication System

12. Electronic Ballast (for the

CLEARRAY System)

13. Control Panel

14. Quick Drain

15. SunSmart™ 2.0 Wi-Fi (Optional)

16. BLUEWAVE® 2.0 Wireless Audio

System (Optional)

Page is loading ...

Sundance Spas Maxxus Owner's manual

Sundance Spas Maxxus Owner's manual

Related papers

Other documents