digital drum assembly instructions
SD7K
Inside this package
Before assembly, please make sure that all the items listed below are present.
CAUTION!
As a by-product of the manufacturing process, occasionally some metal shavings or burs will unavoidably remain.
To avoid injury, please watch your fingers when adjusting clamps, or when working around pipe-ends and screw-ends.
Cymbal 3pcs
Drum Pads
Accessories
Kick Pad
Leg (L)
Leg (R) Center Pipe (1)
3 Cymbal Pads
2 Tom Pads
2 Metal Rods
Kick Pad
Hi-Hat Pedal
Hi-Hat
Control Pedal
Drum Pads
2 Cymbal Holders (Long)
2 Drumsticks
Side Arm (L2)
Holder Clamp
Side Arm (R)
Cymbal Holder Clamp
Holder Clamp
Clamp ConnectorCross Pipe
Rubber Feet
SD7K
Assembly instructions
Cymbal Holder (Short) Metal Rod
Pillar (R)
Connector
Clamp
Side Arm (L1)
Holder ClampCymbal Holder Clamp
Pillar (L)
Center Pipe (2)
Connector
ClampConnector Cross Pipe
Tom Pad
Snare Pad
Lock Lock Lock
Drum Module
Drum Module
Clamp
Rubber Feet
Holder Clamp
AC Adaptor Instruction Manual
Assembly Instructions
Hexagon Key (5mm)
Drum Key
9 Connecting Cables
2 Metal Rods
digital drum assembly instructions
SD7K
Pillar (L)
Side Arm (L1)
23
24
Diagram 7
Assembly
I. Setting up the frame of the digital drum KIT
Pillar (L)
Leg (L)
3 5 6
1
4
6
2
Diagram 1
Left Leg Assembly
16
15
Center Pipe
Diagram 4
18
19
20
17
Diagram 5
Pillar (L)
Side Arm (L1)
22
21
Diagram 6
Side Arm (L2)
Attach the Pillar (L) to the clamp on the Leg (L).
Using the drum key, tighten the screws on the clamp.
Remove the screw attached to the connector.
Attach the cross pipe to the connector.
Re-attach the screw into the connector.
Tighten the screw on the connector.
1
5
4
3
2
6
Attach the Pillar (R) to the clamp on the Leg (R).
Tighten the screws on the clamp.
Remove the screw attached to the connector.
Attach the cross pipe to the connector.
Re-attach the screw into the connector
Tighten the screw on the connector.
7
11
12
10
9
8
Attach Center Pipe(1) to the clamp on the
Left Leg Assembly.
Tighten the screws on the clamp.
14
13
Attach the Right Leg Assembly to the
Center Pipe(1) .
Tighten the screws on the clamp.
16
15
Attach Center Pipe (2) to the clamp on the
Left Leg Assembly
Tighten the screws on the clamp.
Attach the Right Leg Assembly to the Center Pipe(2).
Tighten the screws on the clamp.
18
20
19
17
Attach the Side Arm (L2) to the clamp on the Pillar (L).
Tighten the screws on the clamp.
24
23
Pillar (R)
Side Arm (R)
26
25
Diagram 8
Attach the Side Arm (R) to the clamp on the Pillar (R)
Tighten the screws on the clamp.
26
25
Pillar (R)
Leg (R)
7
8
12
10
12 11 9
Diagram 2
Right Leg Assembly
Pillar (L)
Center Pipe
13
14
Diagram 3
Attach the Side Arm (L1) to the clamp on
the Pillar (L)
Tighten the screws on the clamp.
22
21
digital drum assembly instructions
SD7K
Cymbal Holder (L)
Cymbal Holder (S)
2. Attaching the drum pads
3. Attaching the cymbal pads
Wing Nut
Drum Pad Assembly
Holder Clamp
Holder Clamp
Holder Clamp Holder Clamp
Wing Nut
Felt Washer
2
1 3
4
1 2
1 2
1 2
4 5
Wing Nut
Felt Washer
5
5
3
5
5
Loosen the Wing Nuts on the drum pads.
Remove the Metal Rods.
Re-attach the Metal Rods to the drum pads.
Tighten the Wing Nuts.
Attach the drum pads assemblies to the holder clamps
and adjust their position, then tighten the wing nuts on
the Holder clamps.
Repeat for other pads.
1
5
4
3
2
Attach the Cymbal Holders to the Cymbal
Holder clamps on the Side Arms.
Tighten the Wing Nuts on the Holder clamps.
Remove the Wing Nut and the Felt Washer
of each Cymbal Holder.
Attach the Cymbal pads to the Cymbal Holders.
Re-attach the Felt Washer and Wing Nut, then tighten
the Wing Nut of each Cymbal Holder.
Repeat for other cymbals.
1
5
4
3
2
digital drum assembly instructions
SD7K
3 4
5. congratulations
Cymbal Pad
Tom Pad
Cymbal Pad
Snare Pad
Tom Pad
Drum Module
Kick Pad
0704-7917
Wing Screw
1
2
Metal Rod
Hi-Hat Control Pedal
You’ve successfully assembled your new Simmons SD7K electronic drum kit.
You can now attach your own bass drum pedal to the kick pad. Also, be sure
to attach the clearly marked cables from the pads to the correct inputs on the
drum module.
For connection instructions and more information on your new kit, please refer
to the User Manual or more visit www.simmonsdrums.net.
Attach the Metal Rod to the Drum Module.
Tighten the Wing Screw securely on the Drum Module.
Attach the Metal Rod to the Holder Clamp on the
Side Arm (L1) and adjust the position.
Tighten the Wing Nut on the Holder Clamp.
4
3
1
2
4. Attaching the drum module
-
1
-
2
-
3
-
4
