Panasonic TH-65PF9BK Operating instructions

Category
Plasma TVs
Type
Operating instructions

This manual is also suitable for

Please read these instructions before operating your set
and retain them for future reference.
Model No.
Operating Instructions
High De nition Plasma Display
English
The illustration shown is an image.
TH-50PF9EK
2
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of
enjoyment from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making
any adjustments, and retain them for future reference.
Retain your purchase receipt also, and note down the model number and serial number of
your set in the space provided on the rear cover of these instructions.
Visit our Panasonic Web Site http://panasonic.net
Table of Contents
Trademark Credits
VGA is a trademark of International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, USA.
S-VGA is a registered trademark of the video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to
remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Important Safety Notice ........................................... 3
Safety Precautions ................................................... 4
Accessories .............................................................. 7
Accessories Supply ................................................. 7
Remote Control Batteries ........................................ 7
Connections .............................................................. 8
PC Input Terminals connection ................................ 9
SERIAL Terminals connection ............................... 10
DVI-D connection .................................................. 11
COMPONENT / RGB connection
& RGB signal (R, G, B) .......................................... 11
Power On / Off ......................................................... 12
Initial selections ..................................................... 13
Selecting the input signal ...................................... 13
Selecting the On-Screen Menu Language ............ 13
Basic Controls ........................................................ 14
On-Screen Menu Displays ..................................... 16
ASPECT Controls ................................................... 18
Adjusting Pos. /Size ............................................... 19
MULTI PIP ................................................................ 21
Advanced PIP .......................................................... 22
Picture Adjustments ............................................... 23
Advanced settings ................................................. 24
Sound Adjustment .................................................. 25
Mute ...................................................................... 25
Digital Zoom ............................................................ 26
PRESENT TIME Setup / Set up TIMER .................. 27
PRESENT TIME Setup .......................................... 27
Set up TIMER ........................................................ 28
Screensaver (For preventing after-images) ......... 29
Setup of Screensaver Time ................................... 30
Reduces screen after-image ................................. 30
Side Panel Adjustment .......................................... 31
Reduces power consumption ............................... 32
Customizing the Input labels ................................. 32
Setup for MULTI DISPLAY ...................................... 33
How to Setup MULTI DISPLAY ............................. 33
How to set the display location number
for each Plasma Display ....................................... 34
Seam hides video Setting ...................................... 35
ID Remote Control Function .................................. 35
Setup for Input Signals .......................................... 36
Component / RGB-in select ................................... 36
3D Y/C Filter .......................................................... 36
Colour system / Panasonic Auto ........................... 37
Cinema reality / P-NR ............................................ 37
Sync ...................................................................... 38
H-Freq. (kHz) / V-Freq. (Hz) .................................. 38
Options Adjustments ............................................. 39
Shipping condition ................................................. 42
Troubleshooting ..................................................... 43
DVI-D/COMPONENT/RGB/PC input signals ......... 44
Speci cations ......................................................... 45
3
Important Safety Notice
WARNING
1) To prevent damage which may result in re or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water ( ower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked ame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to quali ed
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only t an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic elds.
Using this appliance near sources of strong electromagnetic elds or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic elds.
IMPORTANT: THE MOULDED PLUG
IMPORTANT: THE MOULDED PLUG
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is
tted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10
amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
ASA
or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is re tted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
If the tted moulded plug is unsuitable for the socket outlet in your home, then the fuse shall be removed
and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug
is inserted into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below.
If in any doubt, please consult a quali ed electrician.
WARNING : — THIS APPARATUS MUST BE EARTHED.
IMPORTANT : —The wires in this mains lead are coloured in accordance with the following code: —
Green-and-Yellow : Earth Blue: Neutral Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which
is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug
which is marked with the letter L or coloured RED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and replace the fuse.
4
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)
Always be sure to ask a quali ed technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces.
The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic
dealer.
Transport only in upright position!
Transporting the unit with its display panel facing upright or downward may cause damage to the internal
circuitry.
Ventilation should not be impleded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For suf cient ventilation;
If using the pedestal (optional accessory) for the Plasma Display, leave a space of at least 10 cm at the top,
left and right, at least 6 cm at the bottom, and at least 7 cm at the rear. If using some other setting-up method,
leave a space of at least 10 cm at the top, bottom, left and right, and at least 7 cm at the rear.
• Speakers ................................................................. TY-SP50P8W-K
• Pedestal .................................................................. TY-ST07-K, TY-ST08-K
• Mobile stand ............................................................ TY-ST42PF3
Wall-hanging bracket (vertical) ................................ TY-WK42PV7
Wall-hanging bracket (angled) ................................ TY-WK42PR7
Wall-hanging bracket (drawer type) ........................ TY-WK42DR1
• Ceiling-hanging bracket .......................................... TY-CE42PS7
BNC Component Video Terminal Board .................. TY-42TM6A
BNC Composite Video Terminal Board ................... TY-42TM6B
BNC Dual Video Terminal Board ............................. TY-FB9BD
DVI-D Terminal Board for PF Series ....................... TY-FB9FDD
RCA Component Video Terminal Board .................. TY-42TM6Z
RCA Composite Video Terminal Board ................... TY-42TM6V
RGB Active Through Terminal Board ...................... TY-42TM6G
• PC Input Terminal Board ......................................... TY-42TM6P
Composite / Component Video Terminal Board ...... TY-42TM6Y
• SDI Terminal Board ................................................. TY-FB7SD
• HD-SDI Terminal Board ........................................... TY-FB7HD, TY-FB9HD
• HDMI Terminal Board .............................................. TY-FB8HM
Ir Through Terminal Board ...................................... TY-FB9RT
• Touch Panel ............................................................ TY-TP50P8-S
• Anti glare lter ......................................................... TY-AR50P9W
5
Safety Precautions
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
Doing so may cause the Plasma Display to overheat, which can cause re or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
Do not insert any metal or ammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause re or electric shock.
Do not remove the cover or modify it in any way.
High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing
connection.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause re. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug
body, not the cable.
• Do not damage the cable, make any modi cations to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause re and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, re or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
A short circuit may occur, which could cause re. Contact your local Panasonic dealer for any repairs that need to
be made.
6
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and re or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in re.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or re ected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water to
which a small amount of neutral detergent has been added, and then wipe it evenly with a dry cloth of the same
type until the surface is dry.
• Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
7
Accessories
Power supply cord × 2 Fixing bands × 2
Remote Control
Transmitter
EUR7636090R
Operating Instruction book
Accessories Supply
Check that you have the accessories and items shown
Remote Control Batteries
Requires two R6 batteries.
1. Pull and hold the hook, then open
the battery cover.
2. Insert batteries - note correct
polarity ( + and -).
3. Replace the cover.
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.
Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
“R6 (UM3)” size
+
+
-
-
I Year Guarantee
Registration
Batteries for the Remote
Control Transmitter
(2 × R6 (UM3) Size)
CRM
( Customer
Relationship
Management)
8
Connections
1
2
1
2
1
2
SERIALPC IN
AUDIO
SLOT1 SLOT3
P
R
/C
R
/R P
B
/C
B
/B
Y/G
AUDIO
RL
COMPONENT/RGB IN
SLOT2
AUDIO
DVI-D IN
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
– Cable xing bands Secure any excess cables with bands as required.
Pass the attached cable
xing band through the
clip as shown in the
gure.
To secure cables connected to Terminals, wrap the cable xing band around them
then pass the pointed end through the locking block, as shown in the gure.
While ensuring there is suf cient slack in cables to minimize stress (especially
in the power cord), rmly bind all cables with the supplied xing band.
To tighten: To loosen:
Pull
Pull
Push the catch
Note:
At factory shipment, Terminal board is installed in SLOT 2 and SLOT 3.
Optional Terminal
Board Insert Slot
(covered)
COMPONENT/RGB IN
and Audio IN Terminals
(see page 11)
From EXTERNAL
monitor terminal on
Computer (see page 9)
From SERIAL Terminal
on Computer
(see page 10)
DVI-D IN
Terminals
(see page 11)
SPEAKERS
Terminals (R)
SPEAKERS
Terminals (L)
Speakers (Optional accessories)
AC cord connection (see page 12)
– AC cord xing
3. Slide up the clamper and x
the AC cord plug securely.
2. Insert the AC cord
and close the clamper
securely.
1. Open the clamper.
Clamper
AC cord
Note: The power plug in the illustration may not be the type tted to your set.
When loosen
the clamper:
4. Insert the point of the
xed clamper into the
small hole on the lower
right of
the back
cover as
necessary.
9
Connections
1
678
3
9
45
10
15 14 13 12 11
2
Notes:
• Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input
Terminal.
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080
dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible
to show ne detail with suf cient clarity.
The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you
will need to make setting changes to the computer at the time of connection.
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
The computer shown in the illustration is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speci ed
frequency range.
Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component connection) or “RGB” (when RGB signal connection). (see page 36)
Signal Names for Mini D-sub 15P Connector
Pin Layout for PC Input
Terminal
PC Input Terminals connection
AUDIO
PC IN
COMPUTER
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Stereo plug
Audio
Connect a cable which matches
the audio output terminal on the computer.
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name
1
R (PR/CR)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (PB/CB)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
NC (not connected)
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
10
SERIAL Terminals connection
Notes:
Use the RS-232C cable to connect the computer to the Plasma Display.
The computer shown is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface speci cation, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satis es the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for
the computer application for details.
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Connections
6789
13452
SERIAL
Pin layout for SERIAL Terminal
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
If there are no parameters, then the parameter signal
does not need to be sent.
Notes:
If multiple commands are transmitted, be sure to wait
for the response for the rst command to come from
this unit before sending the next command.
• If an incorrect command is sent by mistake, this
unit will send an “ER401” command back to the
computer.
Communication parameters
With the power off, this display responds to PON command
only.
COMPUTER
RS-232C Straight cable
D-sub 9p
Start
(02h)
3-character
command (3 bytes)
Colon Parameter(s)
(1 - 5 bytes)
End
(03h)
STX C1 C2 C3 P1 P2 P3 P4: P5 ETX
Command
Signal level RS-232C compliant
Synchronization method Asynchronous
Baud rate 9600 bps
Parity None
Character length 8 bits
Stop bit 1 bit
Flow control -
RS-232C Conversion cable
D-sub 9-pin female Details
2
R X D
3
T X D
5
GND
4
6
Non use
7
8
Shorted
1
9
NC
Command Parameter Control details
PON None Power ON
POF None Power OFF
AVL
**
Volume 00 - 63
AMT
0 Audio mute OFF
1 Audio mute ON
IMS None
SL1
SL2
SL3
PC1
Input select (toggle)
Slot1 input
Slot2 input
Slot3 input
PC input
DAM None
NORM
ZOOM
FULL
JUST
SELF
Screen mode select (toggle)
4 : 3
Zoom
16 : 9
Just
Panasonic Auto
11
Connections
DVI-D connection
SLOT2
AUDIO
DVI-D IN
Mini-plug (M3)
DVI-D
video cable
(Within 5 m)
PC with DVI-D
video out
Pin No.
Signal Name
Pin No.
Signal Name
1
T.M.D.S. data 2-
13
T.M.D.S. data 3+
2
T.M.D.S. data 2+
14
+5 V DC
3
T.M.D.S. data 2/4 shielded
15
Ground
4
T.M.D.S. data 4-
16
Hot plug sense
5
T.M.D.S. data 4+
17
T.M.D.S. data 0-
6
DDC clock
18
T.M.D.S. data 0+
7
DDC data
19
T.M.D.S. data 0/5 shielded
8
20
T.M.D.S. data 5-
9
T.M.D.S. data 1-
21
T.M.D.S. data 5+
10
T.M.D.S. data 1+
22
T.M.D.S. clock shield
11
T.M.D.S. data 1/3 shielded
23
T.M.D.S. clock+
12
T.M.D.S. data 3-
24
T.M.D.S. clock-
Notes:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
Refer to page 44 for applicable input signal.
DVI-D Input Connector
Pin Layouts
Connection port view
16
17
24
8
1
9
AUDIO
OUT
Y, P
B, PR,
OUT
P
R
PB
Y
L
R
COMPONENT VIDEO OUT
SLOT3
P
R
/C
R
/R P
B
/C
B
/B
Y/G
AUDIO
RL
COMPONENT/RGB IN
COMPONENT / RGB connection & RGB signal (R, G, B)
Notes:
Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component connection) or “RGB” (when RGB signal connection). (see page 36)
Additional equipment, cables and adapter plugs shown are not supplied with this set.
Sync on G signal is needed. (see page 38)
RCA-BNC
adapter plug
Computer
RGB Camcorder
or
DVD
Example of input signal source
Digital TV-SET-TOP-BOX
(DTV-STB)
12
Power On / Off
PC
16:9
Connecting the plug to the Wall Outlet
Note:
Main plug types vary between countries. The power plug shown
at right may, therefore, not be the type tted to your set.
Press the Power switch on the Plasma Display to turn the set
on: Power-On.
Power Indicator: Green
Example: The screen below is displayed for a while after the
Plasma Display is turned on (setting condition is an
example).
When the Power is turned on for the rst
time, the Language selection screen is
displayed.
From the second time on, language
selection can be done from the setup
menu. (see page 13)
Select the desired language using the
or button and press the ACTION (
)
button.
From the second time on, the below
screen is displayed for a while (setting
condition is an example).
Press the button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the switch on the
unit, when the Plasma Display is on or in standby mode.
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma
Display with the clamper. (see page 8)
Italiano
Español
ENGLISH (US)
Русский
English (UK)
Deutsch
Français
OSD Language
SetSelect
INPUT MENU ENTER/+/VOL
-
/
Power Indicator
Remote Control
Sensor
13
Initial selections
.......(Japanese)
.......(Russian)
Русский
.......(Chinese)
Italiano
Français
Deutsch
English(UK)
Español
ENGLISH(US)
1/2
Signal
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD Language English
(
UK
)
Component/RGB-in select
RGB
Input label
Power save
Setup
Selecting the On-Screen Menu Language
Press to display the Setup menu.
Press to select the OSD Language.
Press to select your preferred language.
Selectable languages
Notes:
Selecting is also possible by pressing the INPUT button on the unit.
Input terminal will not be selected if the terminal board is not installed into the
SLOT.
Select to match the signals from the source connected to the component/RGB input
terminals. (see page 36)
In 2 screen display, the same input mode cannot be selected for the main picture
and sub picture.
Selecting the input signal
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from
the equipment which has been connected to the Plasma
Display.
Input signals will change as follows:
INPUT1 INPUT2 PCINPUT3
INPUT MENU ENTER/+/VOL
-
/
INPUT MENU ENTER/
+
/VOL
-
/
14
Basic Controls
SURROUND button
The surround setting switches on and off each time
the SURROUND button is pressed.
The bene ts of surround sound are enormous. You
can be completely enveloped in sound; just as if
you were at a concert hall or cinema.
Note:
The surround settings are memorized separately
for each Sound Mode (Normal, Dynamic, Clear).
On Off
On
Surround
N button (see page 19, 20, 23, 24, 25)
POS. / SIZE button (see page 19)
PICTURE button (see page 23)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
Press to select INPUT1, INPUT2, INPUT3 and PC
input SLOTS sequentially. (see page 13)
Sound mute On / Off (see page 25)
Numeric buttons (see page 35, 41)
ASPECT button
Press to adjust the aspect. (see page 18)
MULTI Window buttons (see page 21)
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen
will switch. (see page 16)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
(see page 13)
Power Indicator
The Power Indicator will light.
Power-OFF ....Indicator not illuminated (The unit
will still consume some power
as long as the power cord is still
inserted into the wall outlet.)
• Standby ..........Red
• Power-ON ......Green
• DPMS .............Orange (With PC input signal
and during operation of PC’s
screensaver.)
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is displayed:
“+” : press to move the cursor up
“–” : press to move the cursor down
(see page 16)
Enter / Aspect button
(see page 16, 18)
Remote control sensor
Normal Viewing Picture Setup
Sound Pos. /Size
INPUT MENU ENTER/
+
/VOL
-
/
Main Power On / Off Switch
15
Basic Controls
Standby (ON / OFF) button
The Plasma Display must rst be plugged into the wall outlet and turned on at the power switch (see page 12).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off
to Standby mode.
POSITION buttons
SET UP button (see page 16, 17)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to
select the PC input mode.
This button is used to switch directly to INPUT mode.
These buttons can only display the slot which is installed. If you
press the button whose slot is not installed, it automatically displays
the current input signal.
Note:
After-image (image lag) may occur on the plasma display panel when
a still picture is kept on the panel for an extended period. The function
that darkens the screen slightly is activated to prevent after-image (see
page 43), this function is not the perfect solution to after-image.
Channel Adjustment
This button cannot be used for this model.
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease
the sound volume level.
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a xed
period. The setting changes to 30 minutes, 60 minutes, 90 minutes
and 0 minutes (off timer cancelled) each time the button is pressed.
When three minutes remain, “Off timer 3” will ash.
The off timer is cancelled if a power interruption occurs.
Remote ID lock (see page 35)
Status button
Press the “Status” button to display the current system status.
1
Input label
2
Aspect mode (see page 18)
3
Off timer
The off timer indicator is displayed only when the off timer
has been set.
Digital Zoom (see page 26)
Press to access
Digital Zoom.
This displays an enlargement of the designated part of the
displayed image.
ACTION button
Press to make
selections.
SOUND button
(see page 25)
R button (see page 17)
Press the R button to return to previous menu screen.
Off timer 90
2
3
1
PC
4:3
30 60
0
90
16
1
2
On-Screen Menu Displays
1/2Picture
Normal
Normalise
Normal
25
0
0
0
5
Brightness
Sharpness
Picture Mode
Colour
Contrast
Tint
2/2Picture
Advanced settings
White balance
Colour Management
Normal
Off
On
Advanced settings
Normal
Normalise
0
0
0
0
0
0
2.2
Off
W/B Low B
Black extension
W/B High B
W/B Low R
AGC
Gamma
Input level
W/B High R
Sound
Normal
Normalise
Normal
0
0
0
Off
Treble
0
Mid
Sound Mode
Balance
Bass
Surround
Main
Audio Out (PIP)
1/2
Signal
PC
Off
Standby save
Off
Power management
Off
Auto power off
Off
OSD Language English
(
UK
)
Component/RGB-in select
RGB
Input label
Power save
Setup
2/2Setup
Screensaver
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
To Sound adjust menu
(see page 25)
To Advanced settings
(see page 23, 24)
Press to select
“On”.
Press to enter
Advanced settings.
To Picture adjust menu
(see page 23)
The MENU button on the unit can also
be pressed.
Each time the MENU button is pressed,
the menu screen will switch.
1
Press to select.
Normal Viewing Picture Setup
Sound Pos. /Size
To Pos. /Size adjust menu
(see page 19)
During “Video (S Video)”, “Digital”,
“SDI” and “HDMI” input signal.
0
Normal
Normalise
Auto Setup
Pos. /Size
V-Pos
0
H-Pos
V-Size
Dot Clock
H-Size
Clock Phase
1:1 Pixel Mode
Off
0
0
0
0
During “Component”, “RGB” and
“PC” input signal.
0
0
0
Normal
Normalise
Pos. /Size
V-Pos
H-Pos
0
V-Size
H-Size
1:1 Pixel Mode
Off
Auto Setup
[ from the unit ]
1
Press to select.
2
Press to access each adjust
screen.
INPUT MENU ENTER/+/VOL
-
/
INPUT MENU ENTER/+/VOL
-
/
17
On-Screen Menu Displays
Sync
P-NR
Signal
Auto
H-Freq.
V-Freq.
kHz
Hz
33.8
60.0
[
RGB
]
Cinema reality
Off
Off
Cinema reality
P-NR
Signal
Off
Off
[
Component
]
3D Y/C Filter (NTSC)
Colour system
Signal
On
Auto
Cinema reality
Panasonic Auto (4 : 3)
Off
4 : 3
[
AV
]
P-NR
Off
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
Off
0:00
Off
0:00
PRESENT TIME 99:99
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
Off
0:00
Off
0:00
PRESENT TIME 99:99
Set up TIMER
POWER OFF Function
POWER OFF Time
POWER ON Time
POWER ON Function
Off
0:00
Off
0:00
PRESENT TIME 99:99
PRESENT TIME Setup
Set
PRESENT TIME
99:99
PRESENT TIME 99:99
Cinema reality
P-NR
Signal
Off
Off
H-Freq.
V-Freq.
kHz
Hz
33.8
60.0
[
Digital
]
2
Press to access
each adjust
screen.
Press the R button to return to
previous menu screen.
Note : “Signal” setup menu displays different setting condition for each input signals. (see page 13)
To Signal screen for
Component (see page 37)
To Signal screen for RGB
(see page 37, 38)
Press the R button to return
to “Setup” menu.
Press to select POWER ON
Time / POWER OFF Time.
Press to Set up
POWER ON Time /
POWER OFF Time.
To Set up TIMER selection
screen (see page 27, 28)
To PRESENT TIME Setup
(see page 27)
Press to return to next menu screen.
To Signal screen for Digital
(see page 37, 38)
Press the R button to return
to “Setup” menu.
Press to Setup.
Press to select Start Time / Finish Time
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
To setup Screensaver
(see page
29-31
)
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Operating Time
Periodic Time
White bar scroll
Interval
6:15
12:30
High
Off
Off
PRESENT TIME 99:99
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Finish Time
Start Time
White bar scroll
Time Designation
6:15
12:30
High
Off
Off
PRESENT TIME 99:99
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Finish Time
Start Time
White bar scroll
Time Designation
6:15
12:30
High
Off
Off
PRESENT TIME 99:99
Screensaver
Start
Function
Mode
Side panel
Wobbling
Peak limit
Operating Time
Periodic Time
White bar scroll
Interval
6:15
12:30
High
Off
Off
PRESENT TIME 99:99
To setup Multidisplay screen.
(See page 33)
To Signal screen for AV
(S Video) (see page 36, 37)
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
× 2
MULTI DISPLAY Setup
Horizontal Scale
Off
Off
A1
Location
Vertical Scale
Seam hides video
× 2
MULTI DISPLAY Setup
[ from the unit ]
INPUT MENU ENTER/+/VOL
-
/
18
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
[During MULTI PIP Operations]
• Picture and Picture, Picture in Picture :
• Others : Aspect switching is not possible.
Notes:
For PC signal input, the mode switches between “4:3”, “Zoom” and “16:9” only.
For a 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) /
60p · 50p signal input, the mode is set to “16:9” mode, and switching is not possible.
Panasonic Auto can be selected only during Video signal input.
The aspect mode is memorized separately for each input terminal.
Mode Picture Explanation
4 : 3
4 : 3
3
4
4:3 will display a 4:3 picture at its standard 4:3 size.
Zoom
Zoom
4
3
16
9
Zoom mode magni es the central section of the picture.
16 : 9
16 : 9
4
3
16
9
16:9 will display the picture at its maximum size but with slight
elongation.
Just
Just
4
3 9
16
Just mode will display a 4:3 picture at its maximum size but with
aspect correction applied to the center of the screen so that
elongation is only apparent at the left and right edges of the screen.
The size of the picture will depend on the original signal.
Panasonic
Auto
Panasonic Auto
416
39
The display will automatically become enlarged (depending on the
picture source), allowing you to view the picture at its maximum
size.
Notes:
Panasonic Auto mode is designed to automatically adjust the
aspect ratio to handle a mix of 16:9 and 4:3 program material.
Certain 4:3 program material, such as stock market data screens,
may occasionally cause the image size to change unexpectedly.
When viewing such programs, it is recommended that the ASPECT
be set to 4:3.
• If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9
mode, the adjustment is not memorized. When exiting the mode,
the screen will return to a former adjustment.
• Panasonic AUTO can not be selected while TY-FB9BD (optional
BNC Dual Video Terminal Board) is installed.
For an elongated image
Image is expanded
4
3
Changes in
accordance with
the Panasonic Auto
mode setting (see
page 37).
For a 4:3 image
Note:
Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent after-image
to remain on the Plasma Display Panel.
[from the unit]
4 : 3 16 : 9
4 : 3 Zoom 16 : 9
Panasonic Auto Just
Press repeatedly to move through the aspect options:
The aspect mode changes each time the ENTER button is
pressed.
INPUT MENU ENTER/+/VOL
-
/
19
Adjusting Pos. /Size
1
Press to display the Pos. /Size menu.
Press to select Auto Setup / H-Pos / H-Size / V-Pos /
V-Size / Dot Clock / Clock Phase / 1:1 Pixel Mode.
Press to adjust Pos. / Size.
Press to exit from adjust mode.
3
2
Notes:
Adjustment details are memorized separately for different input signal formats
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p,
625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p ·
24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital
signals are memorized for each frequency.)
If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture
position will shift up or down. This picture position movement cannot be
controlled by the Picture Pos./Size function.
If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 mode, the
adjustment is not memorized. When exiting the mode, the screen will return
to a former adjustment.
While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Helpful Hint ( /
Normalise
Normalisation)
4
During “Video (S Video)”, “Digital”,
“SDI” and “HDMI” input signal.
0
Normal
Normalise
Auto Setup
Pos. /Size
V-Pos
0
H-Pos
V-Size
Dot Clock
H-Size
Clock Phase
1:1 Pixel Mode
Off
0
0
0
0
During “Component”, “RGB” and
“PC” input signal.
0
0
0
Normal
Normalise
Pos. /Size
V-Pos
H-Pos
0
V-Size
H-Size
1:1 Pixel Mode
Off
Auto Setup
20
Adjusting Pos. /Size
While the Pos. /Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Helpful Hint ( /
Normalise
Normalisation)
Auto Setup
Automatically adjust H-Pos / V-Pos / Clock Phase / Dot Clock and set H-Size / V-Size the
standard value when RGB signal is input.
Notes:
If the dot clock frequency is 162 MHz or higher, Dot Clock cannot be made.
If the image is that the edge is hardly gured out or shadowy, that cannot be adjusted
automatically.
In such case, press Auto Setup again after changing the image to the clearer one.
When DVI-D is input, Clock Phase cannot be adjusted automatically.
Select Normalise in Pos. /Size and press the ACTION ( ) button when appropriate
adjustment cannot be made.
H-Pos Adjust the horizontal position.
H-Size Adjust the horizontal size.
V-Pos Adjust the vertical position.
V-Size Adjust the vertical size.
Dot Clock (During “Component”, “RGB” and “PC” input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this
happens, adjust so that any such noise is minimized.
Clock Phase (During “Component”, “RGB” and “PC” input signal)
Eliminate the ickering and distortion.
1:1 Pixel Mode Adjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
Select On when you would like to replay 1920 × 1080 input signal.
Applicable input signal;
1125 / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p · 1250 / 50i
Select Off when ickering is shown around the image.
H-Size, V-Size and Dot Clock cannot be adjusted when On is selected.
Off On
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Panasonic TH-65PF9BK Operating instructions

Category
Plasma TVs
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI